RUNWAY LIGHTING
HIRL
High-Intensity Elevated Edge Light
Compliance with Standards
T/C:
ICAO:
FAA:
K311, Type HIRL, MITL TP 312 - with CSA Attestation.
Annex 14, Vol. 1 Para. 5.3.9 to 5.3.11
L-862 to AC 150/5345-46A.
Uses
• High-intensity edge lighting for runways up to 60 m wide, in
CAT I, II, and III conditions.
• Medium-intensity runway edge and threshold/end lighting.
• The 5NQ3850CU fixture also has omnidirectional output for
circling guidance.
Features
• Low profile and small in size to withstand high jet blast, even
when installed at threshold/runway end.
• Smooth outer glass resists dirt, pitting and damage compared
to large lenses of old C1 type fixture.
• 2” Slipfitter provides for mounting on standard 2” frangible couplings for overall height ranges of 350 mm to 760 mm.
• Energy-efficient optics utilize a 150 W lamp for H.I. edge light
applications, compared to 204 W for the old C1 type fixtures. Use
of PK30d style lamps eliminate the need for lamp sockets and the
high maintenance bi-pin type lamps.
• Lamp life is rated 1500 hrs at full brightness but typically 4000
– 6000 hrs in actual service. Easy re-lamping is accomplished
without requirement for tools and involves loosening only one
thumbscrew.
• Low maintenance design minimizes quantity of necessary spare
parts. No small clips or lens holders are used, so lamp changes
can be performed in the field by maintenance personnel wearing gloves.
• Many fixture components are compatible with ADB L861U type
fixture to reduce spares requirements.
Ordering Code
Lamp Size
45 = 45 W, 6.6 A PK30d Quartz Halogen1
10 = 100 W, 6.6 A PK30d Quartz Halogen2
15 = 150 W, 6.6 A PK30d Quartz Halogen3
20 = 200 W, 6.6 A PK30d Quartz Halogen
Notes
1
45 W Lamp is used for taxiway edge and heliport perimeter
applications only. Refer to type L861U fixtures for standard
taxiway edge light configuration.
2
100 W Lamp is used for medium intensity threshold/end light
configuration.
3
150 W Lamp is used for standard H.I. edge lighting
applications.
RUNWAY
• Four screws allow for ease of leveling fixture after installation.
Optional fixture leveling tool is available.
GREEN
L
• Fixture has provision for mounting of edge light flags or markers
with suitable mounting brackets.
THRESHOLD / END LIGHTS
RED
R
• Fixture can have side or centre cable exit without requiring
disassembly of fixture.
-
Lens Configuration
0A = Clear Inner/Clear Outer
2AA = Clear/Yellow Inner Left, Clear Outer
2AB = Clear/Yellow Inner Right, Clear Outer
2BZ = Yellow Outer Only (Omni, Twy/Heliport)
4A = Red Inner/Clear Outer
4AA = Red/Blank Inner Left, Clear Outer
4AB = Blank/Red Inner Right, Clear Outer
4BZ = Red Outer Only (Omni, Twy)
5AA = Clear/Blue Inner Left, Clear Outer
5AB = Blue/Clear Inner Right, Clear Outer
5BZ = Blue Outer Only (Omni, Twy)
6AA = Red/Green Inner Left, Clear Outer
6AB = Green/Red Inner Right, Clear Outer
6BZ = Green Outer Only (Omni, Heliport)
XXX = Non-standard (Consult ADB)
• Versatile optical system with 2-piece, 180-degree inner lenses
allows for any combination of colours. Blanking shields and thru
coloured outer lenses are also available for specific applications.
• Robust cast aluminum fixture body helps reduce damage caused
by maintenance and snow removal equipment. Durable aviation yellow finish and stainless steel hardware provide for an
extended fixture life.
5NQ3850CU-
RED
R
L
GREEN
THE LETTER "R" OR "L"
INDICATES THAT THE
APPROACH / DEPARTURE
CENTRELINE IS TO THE RIGHT
OR LEFT RESPECTIVELY.
Inner Lens Configuration for Threshold/End Lights
C1001 Rev. B I Call for manual
C-1
RUNWAY LIGHTING
HIRL I High-Intensity Elevated Edge Light
Packaging
Suggested Specification
Assembled fixture c/w lens and lamp
The Runway Edge Light shall be high intensity, elevated, in full
compliance with Transport Canada Specifications K311 and
TP 312 and meet the requirements of FAA L-862 specification (AC
150/5345-46B) and with ICAO Annex 14, Vol. I, para. 5.3.9. for
use in Category I, II and III systems.
Weight
7 lb (3.2 kg) each fixture
Packaging Dimensions
(4 fixtures per box)
15 x 15 x 16 in
(38.1 x 38.1 x 40.6 cm)
The prefocus halogen lamp shall be 150 W, 6.6 A, rated life of not
less than 1500 hours at full intensity and approx. 4000 – 6000 hrs
in actual service. The lamp shall be retained by a fool proof positioning device and should not require the use of any type of lamp
socket. Lamp changes will be accomplished without the use of
hand tools and without disassembly of the optical lenses.
Overall height of the light when installed, shall not exceed 350 mm
and its total weight shall be 4 kg or less. The light shall consist
of heavy-duty aluminum alloy castings for the body components,
heat-resistant glass optical parts and plain stainless hardware.
Gaskets and electrical wiring shall be high temperature resistant.
The light shall be suitable for direct installation on any standard
2” breakable coupling. The light shall resist jet blast from the
heaviest present day aircraft and shall be frangible in case of
impact.
The optical system shall consist of a double lens. Its outer
component shall have an externally smooth surface to prevent
accumulation of dirt. The inner lens shall be in one or two halves,
through-coloured when required.
Spare Components
Description
Part No.
(A) Clear Outer Glass Lens
(B) Blue Outer Glass Dome (Sym.)
(B) Yellow Outer Glass Dome (Sym.)
(B) Red Outer Glass Dome (Sym.)
(B) Green Outer Glass Dome (Sym.)
(C) Inner Clear Lens
(C) Inner Red Lens
(D) Inner 1/2 Lens Green Right
(D) Inner 1/2 Lens Green Left
(D) Inner 1/2 Lens Red Right
(D) Inner 1/2 Lens Red Left
(D) Inner 1/2 Lens Clear Right
(D) Inner 1/2 Lens Clear Left
(D) Inner 1/2 Lens Yellow Right
(D) Inner 1/2 Lens Yellow Left
(D) Inner 1/2 Lens Blue Right
(D) Inner 1/2 Lens Blue Left
(D) Inner 1/2 Shield Obscured
Lamp, 45W 6.6A PK30d (1)
Lamp, 100W 6.6A PK30d (1)
Lamp, 150W 6.6A PK30d (1)
Lamp, 200W 6.6A PK30d (1)
Halogen Lamp Support (2)
Outer Dome Gasket (3)
Inner Globe Holder (4)
Aluminum Snap-on Band (5)
Fixture Optic Carrier, Universal (6)
Fixture Base, Universal (7)
Slipfitter Base, Universal (8)
Cable Assembly (9)
5NQ-9638-0K
5NQ-9638-0B
5NQ-9638-0Y
5NQ-9638-0DR
5NQ-9638-0G
5NQ-9638-0R
5NQ-9638-0RZ
5NQ-9638-3RR
5NQ-9638-3RL
5NQ-9638-4RR
5NQ-9638-4RL
5NQ-9638-1RR
5NQ-9638-1RL
5NQ-9638-2RR
5NQ-9638-2RL
5NQ-9638-5RRZ
5NQ-9638-5RLZ
5NQ-9638-2K
64317
64342
64361HLX
64382
951016
930407-4
4071-22-690
SAT-9738-0K
930407-1
930407-2
940112
91 MPC-.46-H
Product specifications may be subject to change,
and specifications listed here are not binding.
Confirm current specifications at time of order.
C-2
C1001 Rev. B I Call for manual
1
A
2
B
3
4
5
6
C
D
7
Lens Styles
8
R
9
Fixture Exploded View
ADB Airfield Solutions
Leuvensesteenweg 585
B-1930 Zaventem
Belgium
ADB Airfield Solutions, LLC
977 Gahanna Parkway
Columbus, OH 43230
USA
Telephone: +32 (0)2 722.17.11
www.adb-air.com
Telephone: +1 614.861.1304
+1 800.545.4157
FAA L823 STYLE 1
© ADB Airfield Solutions
All rights reserved