QUICKSTART “BASIC” HARDWIRE TRACKER EXPANSION BOARD TO RELAY 2/WIEGAND 2 GUIDELINES
For COMPLETE installation instructions, please refer to the HARDwired Installation/Owner’s manual P/N 2358-065.
Tracker Expansion Board Enclosure Options
Access Control
System Board
RS 232
Single Board Enclosure with
Built-In Card Reader and Lighting
DK Prox Reader - P/N 1815-333
HID Reader - P/N 1815-392
AWID Reader - P/N 1815-292
Single Board Enclosure
P/N 2351-080
120 Glasgow Avenue
Inglewood, California 90301
Quad Board Enclosure
P/N 2351-081
U.S.A.
ELEVATOR
1
2
Tracker Expansion Board Notes:
3
7
8
9
10
2C 2RY
15
16
1C
1NC 1NO BAT 16AC 16AC
17
18
19
20
NO
Relay 1
BOARD ADDRESS
1
0
ON
4 5 6
RF
SECURE
RF
RF
DATA STATUS
CODE CODE CODE
SENT GOOD BAD
7 8
OUTPUT
RELAY
NC
NO
ALARM
RELAY
NC
NO
AUX
RELAY
NC
NO
2358-010
RESET
Ground
12 GA. Wire
ENT
Tracker Expansion
Board Address 3
Board Power
16.5 VAC, 20 VA
Required
18 GA. Wire 100 ft max
16 GA. Wire 200 ft max
BOARD ADDRESS
1
Gate Operator Control
UT
TP
OU LAY
RE
NC
Relay
Jumper
0
To #8
Red #10
Blue #17
To #18
Brown #19
SH
PU
TO
ON
RF
SECURE
RF
RF
DATA STATUS
CODE CODE CODE
SENT GOOD BAD
7 8
OUTPUT
RELAY
NC
NO
ALARM
RELAY
NC
NO
AUX
RELAY
NC
NO
2358-010
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
RESET
NO
Lock
Power
Electric Strike
Door Lock
Ground #32
Ground
ENT
Tracker
Expansion
Board
Address 4
IT
EX
Request to Exit
(Free Exit)
Green #29-Data 1
White #28-Data 0
Black #27-Com
#20-Card Reader LED
OR Beeper Control
(Available on certain
card readers)
OR
NO
Ground #32
Card Reader
N
Output Relay
#25 & #26
UT
TP
OU LAY
RE
NC
Black #27-Com
White #28-Data 1
Green #29-Data 0
21
22
23
24
25
26
27
28
29
30
31
32
33
34
0
OFF
Relay
Jumper
Board Address 10
Setting
7 8
Power #33
Power #34
1
2
6 conductor, stranded with overall
3
shield, 18-22 gauge. 500 ft max.
4
DO NOT use twisted pair.
5
#6-Green = Data 0
6
#7-White = Data 1
7
#8-Black = Common
8
#9-Red = 12 VDC Power
9
10
#10 connects 11
ONLY to tracker 12
expansion boards 13
14
15
16
17
18
19
20
NCO
Black #27-Com
White #28-Data 1
Green #29-Data 0
Com Brown #19
26, 30, 31-Bit Wiegand
Power for electric
strike or magnetic
lock is NOT
provided by the
board. Use
separate UL listed
power supply.
Power #33
Power #34
N.O. Blue #17
Wiegand Access
Control Device
Blue - Beeper
Relay 2
Set Output
Relay Jumper
UT
TP
OU AY
Maglock REL
1
ON
90 1
Relay 2
Jumper
Main
Power
0
OFF
Black #27-Com
White #28-Data 1
Green #29-Data 0
NC
Note: If card
reader has
additional
lighting for
outdoor use,
separate power
must be
provided.
Switch MUST be OFF (0)
for board addresses 3 thru 9.
NO
4 5 6
9 10 11 12 13 14
6 7 8
Relay 2
Jumper
13 14
OR
Yellow - LED
Important Note: Relay 2 is used to
control tracker expansion board
addresses 3-10, Relay 1 or Relay 0 can
be used as the Primary Relay that will
open a visitor door or gate when the
resident pushes “9” on their telephone.
A
90 1
Main Door/Gate
Relay 1 or Relay 0
12
Z
Blue #14
Switch closure across
terminals 4 & 6 will
activate relay 1 for its
programmed strike time.
(Postal Lock)
11
0
OFF
BOARD ADDRESS
Relay
Jumper
4 5 6
6
Electric
strike
UT
TP
OU LAY
E
R
NC
4 56
5
4 56
4
Brown #13
Central Office
phone line touch tone,
loop start.
3
CGND PSW MIC COM SPKR IMD 5VDC IMC
7 8
Red #10
2
PHONE
DK Prox Reader
Aux
Power
1
ON
Second Board Address
Set to 4
9 0 1
1
NC
Switch MUST be ON (1)
for board address 10.
2 3
RING
NO
C
Card Reader
1
Door Lock Control
BOARD ADDRESS
9 0 1
NO NC
First Board Address
Starts at 3
9 0 1
Relay 0
ON
MASTER
CODE
OFF
KEYPAD
1 2 3 4 5
Auxiliary Terminal
CLK
SEN
Board addresses MUST start at 3 and contiunue thru
board address 10 (up to
BOARD ADDRESS
12 boards using Zone
ON
Addresses) if required.
7 8
2 3
3 2 1
Communication line will continue for each board like
shown on tracker expansion board address 4.
Tracker expansion boards connected to Wiegand 2 will activate
Relay 2 in the access control system.
2 3
3 2 1
FEED
BACK
Communication 2
Black #9-Com
White #8-Data 1
Green #7-Data 0
2 3
3 2 1
SPK
VOL
Auxiliary
Terminal
2 3
MIC
VOL
All tracker expansion boards can be wired with
desired options for their access points like shown on
tracker expansion board address 3.
Board Power
To #18
To #8 Com
SH
PU
TO
IT
EX
Request to Exit
(Free Exit)
Tracker Expansion
Board “Busy” #10
Typical BASIC Tracker
Expansion Board
Wiring Options
for Access Point
NO “optional” tracker features or battery back-up wiring shown, see manual for details.
Use 6 conductor stranded with overall shield. 18 - 22 gauge.
ONLY use 18 gauge when wiring more than 8 boards.
DO NOT connect shield to 2358-010 board common.
DO NOT use twisted pair.
To Board Addresses 5 thru 10
Communication Line
Up to 12 tracker expansion boards can be HARDwired to relay 2/wiegand 2 at the access control system.
IMPORTANT: The maximum distance for a tracker expansion board HARDwire run is 4000 feet TOTAL (1 to 12 boards
can be in a HARDwire run). The farthest board can be NO more than 2000 feet away from the access control system.
See manual for multiple tracker expansion boards layout limitations.
QUICKSTART PROGRAMMING OPTIONS ON EACH HARDWIRED TRACKER EXPANSION BOARD GUIDELINES
For COMPLETE programming instructions, please refer to the HARDwired Installation/Owner’s manual P/N 2358-065.
BOARD ADDRESS
Relay Communication Line (NO)
Request to Exit
Relay Communication Line (Com)
Card Reader LED/Beeper Control
ON
CODE CODE CODE
SENT GOOD BAD
7 8
4 5 6
0
OUTPUT
RELAY
NC
NO
ALARM
RELAY
NC
NO
AUX
RELAY
NC
NO
2358-010
Relay jumpers MUST be
set for each relay used.
2 3
Data 0
Data 1
Access Control Device
26, 30, 31-Bit Wiegand
Com
12 VDC
Tracker Expansion Board Busy
1
RF
RF
DATA STATUS
90 1
Board addresses MUST be
set for each board used.
RF
SECURE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Programming Options on EACH Tracker Expansion Board
Program
Step
Aux Relay
Description
Selection
Options Number
1
Door Strike Timer
00 - 99
00
01 - 99
2
Free Exit Timer, Strike Time
00 - 99
00
01 - 99
3
Door Ajar Timer
00 - 99
00
01 - 99
4
Aux Relay Timer
00 - 99
00
01 - 99
5
Free Exit Timer, Aux Relay
00 - 99
00
01 - 99
6
Free Exit, No Strike
0 or 1
0
1
7
Not Used
8
Door Contact Switch Logic
0 or 1
9
Auto Relock
0 or 1
10
Beeper / LED Hold Open
0 or 1
11
Hold Open or Hold Egress functions
0 or 1
12
Dual Door Mode
0 or 1
13
14
Not Used
Not Used
Alarm Relay
Output Relay
Com
Data 1 Tracker Communication Line
Data 0
(-) 12VDC Battery
(+) 12VDC Back-Up
Ground - Required
RESET
Board Power
16.5 VAC, 20 VA
Required
ENT
LED Display
Programming
Buttons
Basic Programming Sequence on EACH Tracker Expansion Board
Follow these basic steps to perform desired programming, See programming options table for PROGRAM STEPS.
1. Press
arrow buttons or ENT button to ACTIVATE LED display.
2. Press
arrow buttons again to CHOOSE desired PROGRAM STEP.
IMPORTANT Display Decimal Point Note
3. Press ENT button to ENTER desired PROGRAM STEP.
(LED display number will blink after ENT button has been pressed).
4. Press
4
arrow buttons to choose SELECTION NUMBER for desired function of program step.
When decimal point is NOT displayed:
Indicates that you are IN a program step.
5. Press ENT button to program SELECTION NUMBER for desired function of program step.
(Function has now been programmed into board).
5
15
Aux Relay Functions
0 - 12
6. Press ENT button again to exit programming OR after 10 seconds, board will automatically exit programming.
After all tracker expansion boards have been programmed.....
Alarm Relay Functions
Manage the Complete Access Control System from Your PC
Refer to the DKS Remote
Account Manager Software
to program and manage the
complete system.
SO
INS FTW
TA AR
LL E
ED
TELEPHONE ENTRY SYSTEM
SP
ABC
DEF
GHI
JKL
MNO
TUV
WXYZ
1
4
PQRS
7
2
5
8
3
6
9
OPER
Your PC connected to the access control system.
Either IM Server OR TCP/IP OR RS-232 OR Modem
to Modem Connection. See PC Programmable
Telephone Entry and Access Control Systems
Installation/Owner’s manual for more information
about connection options.
6
7
8
9
10
11
12
Note: Repeat these steps for all other desired programming functions.
Each tracker expansion board will have to be INDIVIDUALLY programmed with desired functions.
0
HOLD TO SCAN
OPERATING INSTRUCTIONS
1. Use “A to Z” Buttons to Locate
Name and Code Number on Display.
Names are In Alphabetical Order.
2. T o Call, Enter Code Number on
Keypad or Press “Call” Button. If
Line is Busy, Press “#” or “Call” to
Hang Up. Try Again.
3. Enter on Open Display and Tone.
A
Z
CALL
Door Operation Note:
PROPER Condition: The access control
system OR request to exit device HAS
activated the OUTPUT RELAY on the
tracker expansion board and the door
contact switch is CLOSED (Door is
OPEN). This indicates that the door has
been PROPERLY OPENED.
16
FORCED Condition: The access control
system OR request to exit device has
NOT activated the OUTPUT RELAY on
the tracker expansion board and the
door contact switch is CLOSED (Door is
OPEN). This indicates that the door has
been FORCED OPENED.
17
18
19
20
21
Not Used
Not Used
Reset to Factory Defaults
View RF POT Setting
View RF Signal Loss
22
Card Code Forwarding
Copyright 2013 DoorKing, Inc. All rights reserved.
Function
Sets Strike Time for output relay (term 25 & 26)
0.25 second strike time
Strike time in 1-second increments
Set Strike Time for RX (Request to Exit) of output relay (input at term 18)
0.25 second Egress Strike time
Egress Strike time in 1-second increments
Timer starts when valid access has been granted.
1 second Door Ajar Timer
Timer set in 5-second increments: 01 = 5 seconds, 10 = 50 seconds
Timer setting for Aux Relay activation in 5-second increments
1 second Door Ajar Timer
Timer set in 5-second increments: 01 = 5 seconds, 10 = 50 seconds
Set Strike Time for RX (Request to Exit) of Aux relay (ONLY available if Dual Door Mode step 12 is ON)
0.25 second Egress Strike time
Egress Strike time in 1-second increments
Set RX (Request to Exit) function. Activate Output Relay or do not Activate Output Relay
Do Not Activate Output Relay or Reader Beeper/LED when RX input is received
Activate Output Relay and Reader Beeper/LED for Free Exit Strike Time when RX received
Sets type of Door Switch contacts
0 N.O. contact from door switch with Door Closed (Circuit Open - CO)
1 N.C. contact from door switch with Door Closed (Circuit Close - CC)
Turns on Auto Relock function (not available if Dual Door Mode, step 12 is ON)
0 Output Relay is activated for Strike Time
1 Door Contact Switch required. If door returns to closed position during Strike Time
door will “relock” after 1 second, even if strike time has not expired.
Sets how BEEPER or LED will function during Hold Open
0 When Hold Open occurs, Beeper or LED is active only during Strike Timer
1 When Hold Open occurs, Beeper or LED will remain active during Hold Open
Sets how Aux & Alarm Relay responds during Hold Open or Hold Egress situation
0 No Aux Relay functions. Alarm will be in “Reset”. If Alarm Relay is set for “integral” mode, Alarm relay will not activate. If
Alarm Relay set for “Bypass” mode, Alarm Relay will activate for Hold Open period or Extended Egress Hold.
1 Aux Relay will function for all settings. If Alarm Relay is set for “integral” mode, Alarm relay will not activate. If Alarm Relay set
for “Bypass” mode, Alarm Relay will activate for Hold Open period or Extended Egress Hold.
Sets Tracker to function as 2 Access Points (2 tracker addresses)
0 Disabled, Tracker functions as single access point
Dual Mode: Tracker functions as set board address and next sequential address
1 Card Read will be sent to controller as set board address, access is granted or denied
Card then sent as set address +1, access granted or denied. Aux Relay becomes 2nd output relay. All other Aux Relay functions
disabled. Door Contact switch becomes RX (Request to Exit) for 2nd address.
0
1
2
3
When decimal point is displayed:
Indicates that you are SELECTING
a program step.
120 Glasgow Avenue
Inglewood, California 90301
0
1
2
0-4
3
4
Sets function for Aux Relay
Aux Relay Disabled
No Door Ajar Timer: Requires Door Contact Switch. Aux Relay activates when Door Not Closed.
No Door Ajar Timer, Pulse: Requires Door Contact Switch. Aux Relay “pulses” when Door Not Closed.
Door Ajar Timer: Requires Door Contact Switch. When door opens, start Door Ajar Timer. When timer expires Aux Relay
activates for Aux Relay timer or until door closes, whichever occurs first.
Door Ajar Timer, Pulse: Requires Door Contact Switch. When door opens, start Door Ajar Timer. When timer expires Aux Relay
Pulses for Aux Relay timer or until door closes, whichever occurs first.
Door Ajar, Pulse warning the ON: Requires Door Contact Switch. When door opens, Pulse Aux Relay and start Door Ajar Timer.
When timer expires Aux Relay ON for Aux Relay timer or until door closes, whichever occurs first.
Door opens for any reason, Start Door Ajar timer and pulse Aux Relay. When Door Ajar timer expires, start Aux Timer and
continue Pulsing Aux Relay.
When Door Closes or both timers expire, turn off Aux Relay
Aux Relay as 2nd Alarm Relay. Aux Relay will mirror Alarm Relay functions.
Aux Relay as 2nd Alarm Relay, PULSE. Aux relay will Pulse during any Alarm Relay activation.
Good Card: Aux Relay will activate for Aux Relay timer for any Access Granted Card
Any Card: Aux Relay will activate for Aux Relay Timer when any card has been presented.
Bad Card: Aux Relay will activate for Aux Relay timer when a card has been denied
Warn before Hold Open or Release of Hold Open: Aux relay will activate for Aux Relay timer when scheduled Hold Open begins
or ends. Output Relay will be delayed until Aux Timer expires. DO NOT set Aux Timer above 60 seconds in this mode.
Sets function for Alarm Relay
Aux Relay Disabled
Bypass Mode: Alarm Relay provides “Bypass” to Alarm Door Switch. With proper door input (access or egress) activate Alarm
Relay, start Strike timer and Door Ajar timer. When Door Ajar timer expires, deactivate Alarm Relay.
If second Door Contact Switch is provided, generate transaction for Door Ajar and Door Closed following Door Forced condition.
Also generate transaction for Door Forced condition.
Integral Mode, Door Ajar Timer: Door Contact Switch connected to Tracker, Alarm Relay provides connection directly to Alarm
System. When door is opened for any reason, start Door Ajar timer. When Door Ajar timer expires and Door is still OPEN,
activate Alarm Relay. Reset when door closes.
Send Door Ajar and Door Close transactions.
Integral Mode, Proper and Forced condition: Door Contact Switch connected to Tracker, Alarm Relay provides connection
directly to Alarm System. With proper door input (access or egress) start Strike timer and Door Ajar timer. When Door Ajar
timer expires and Door is still OPEN, activate Alarm Relay. Reset when door closes.
If door is opened without proper condition, activate alarm relay. When door closes deactivate Alarm Relay. Send Door Ajar,
Door Close and Door Forced transactions.
Gate Alarm Function: Alarm Relay will activate for 1 second when tracker board receives a “Gate Forced” or “Gate Obstructed”
transaction from the operator control board.
5 Sets all parameters to Factory Default
5
Adjustable Setting Sets maximum amount of allowable signal strength loss
Displays on LED Displays current signal loss between Base and Tracker.
Sets Wireless Tracker to act as Repeater
ONLY USE AS DIRECTED BY DOORKING TECH SUPPORT 0=Repeater Mode OFF 1=Repeater Mode ON
0 or 1
U.S.A.
Rev-E 1-13-14
Factory
Default
01 - 1 second
01 - 1 second
12 - 60 secs
12 - 60 secs
01 - 1 second
1 - Activate
0 - N.O.
0 - Disabled
0
0 - No relay
functions
0 - Disabled
0 - Disabled
0 - Disabled
0 - Off
2358-066-F-2-14