Reset Form
Wall Forms ® WF31C and WF31H
Half Face Recessed Mount, Round revision 6/17/11 • kl_wf3_spec1.pdf
Fixture
/
Lens
/
Electrical Module
See page 2
/
Finish
/
Options
See page 3
Date:
Page: 1 of 3
1 L"
(44.5 mm)
6 E"
(173.6 mm)
5 B"
(130.2 mm)
10 " - 24 "
(254.0 mm -
609.6 mm)
BACK
SEMI
RECESSED
FULLY
RECESSED
10 E"
(276.2 mm)
5 "
(127.0 mm)
5 E"
(149.2 mm)
Half Face
Recessed Mount
WF31 with LED
Adjustable
Stud Mount
Brackets “H”
Hollow Wall
Models Only
L" NPT Conduit Taps:
“C” Concrete Wall Model: 2 in sides / 2 in bottom
“H” Hollow Wall Models: 2 in bottom Only
Housing:
Recessed Concrete: Die-cast, low copper (<0.6% Cu) aluminum alloy with clear anodize under powder coat finish to match louver and face plate.
Integral junction box (21 cubic inch volume) with four L" NPT conduit taps.
Presswood niche cover provided as temporary protection against moisture.
Recessed Hollow Wall: Die-cast, low copper (<0.6% Cu) aluminum alloy with clear anodize under powder coat finish to match louver and face plate.
Integral junction box (21 cubic inch volume) with four L" NPT conduit taps.
Presswood niche cover provided as temporary protection against moisture.
(HID): Supplied with adjustable stud mount brackets plus insulation detector in place of one side conduit tap. Quick disconnect plug supplied for electrical module.
Face Plate: Die-cast, low copper (<0.6% Cu) aluminum alloy with vertical and horizontal double ribs covering the full hemisphere. Ribs are minimum D" depth and F" thickness. Secures to housing with four stainless steel captive socket head screws.
Half Face: Solid upper half.
Lens: Molded and heat treated glass, F" minimum thickness with internal sandblast. Retained in face plate and sealed with a one-piece silicone gasket.
Choice of smooth (S) or internal prisms (P) .
Socket: (HID): Porcelain medium base socket rated 4KV. (Fluorescent): Plastic
GX24q-3/GX24q-4 base socket. No socket for LED.
Ballast: All components mounted on plate with quick disconnect plug. (HID):
HX-Reactor - High power factor with starting temperatures of -40°F. for HPS and
-20°F. for PMH lamp modes. (Fluorescent): Encapsulated with thermal cutoff.
Electronic with multi-voltage (108v to 305v) input, 50/60 HZ, High power factor with starting temperatures of -0°F.
LED Optical System: A total of 9 LED emitters configured in a rectangular array comprised together as a module. One (1) module for 9 LED version and two (2) modules for 18 LED version. Available in 3500K and 5100K.
LED Driver: Rated for 9 or 18 LED. Universal voltage from 120 to 277V with a ±10% tolerance. -40ºF starting temperature. All drivers are
Underwriters Laboratories recognized.
Finish: Super TGIC thermoset polyester powder coat paint, 2.5 mil nominal thickness, applied over a titanated zirconium conversion coating; 2500 hour salt spray test endurance rating. Standard colors are Black, Dark Bronze, Light Gray,
Stealth Gray ® , Platinum Silver, or White. Custom colors are available.
Pour Items: Recessed housings, devoid of all electrical components. Protective presswood niche covers are supplied to temporarily seal the open housings until the electrical modules and face plates are ready to install. Quick disconnect plugs supplied for electrical modules. For recessed hollow wall configurations, insulation detectors supplied in place of one conduit tap for HID No insulation is permitted above the housing or within 3 " of sides and bottom. Detectors will cut power if fixtures overheat due to insulation.
Finishing Items: Electrical modules and face plates. Each set of finishing items shall be in one container, clearly marked with the fixture catalog number.
CAUTION: Fixtures must be grounded in accordance with national, state, and/or local electrical codes. Failure to do so may result in serious personal injury.
Light distribution
Half Face
Listings and Ratings
ETL 1 to UL Standards 1598 & 8750 IP66 Rated CE 25C Ambient
U.S. PATENTS: D385,054, D381,452, D378,621
1 Suitable for wet locations
KIM LIGHTING RESERVES THE RIGHT TO CHANGE SPECIFICATIONS WITHOUT NOTICE.
© 2011 KIM LIGHTING INC.
• P.O. BOX 60080, CITY OF INDUSTRY, CA 91716-0080 • TEL: 626/968-5666 • FAX: 626/369-2695

Type:
Job:
Wall Forms ® WF31C and WF31H
Half Face Recessed Mount, Round revision 6/17/11 • kl_wf3_spec1.pdf
Page: 2 of 3
Fixture
Cat. No.
Lens
Cat. No.
WF31C
WF31H
S
P
WF31C
WF31H for concrete walls for hollow walls
Molded and heat treated glass, F" minimum thickness with internal sandblast. Retained in face plate and sealed with a one-piece silcone gasket.
Choice of smooth (S) or internal prismed (P)
Smooth Prismed
Electrical Module
HPS = High Pressure Sodium
PMH = Pulse Start Metal
Halide
PL = Compact Fluorescent
LED = Light Emitting Diodes
Lamp Lamp Line
Watts Type Volts
70 PMH 277
For PMH, HPS and PL.
See footnote 2 below for LED
Cat. Nos. for Electrical Modules available:
High Pressure Sodium
50HPS120
50HPS277
50HPS347
Lamp ED-17, Clear
Socket Medium Base
ANSI Ballast S68
Type
70HPS120
70HPS277
70HPS347
ED-17, Clear
Medium Base
S62
Pulse Start Metal Halide
50PMH120
50PMH277
50PMH347
ED-17, Clear
Medium Base
M110
70PMH120
70PMH277
70PMH347
ED-17, Clear
Medium Base
M98
Compact Fluorescent
42PL 1
Lamp Compact Fluor.
Socket GX24q-4 Base
LED
9L3KUV 2
9L5KUV
LED
N/A
2
18L3KUV 2
18L5KUV 2
LED
N/A
1 42PL operates 26, 32, and 42 watt lamp at 120 thru 277 volts (50-60 Hz.)
2 For LED, 9L = 9LED Emitters; 18L = 18 LED Emitters; 3K = 3500K color temperature;
5K = 5100K color temperature; UV = Universal Voltage from 120 to 277V with a ± 10% tolerance.
Finish
Super TGIC powder coat paint over a titanated zirconium conversion coating.
Color: Black Dark Bronze Light Gray Stealth Gray ®
Cat. No.: BL DB LG SG
Platinum Silver White Custom Colors 3
PS WH CC
3 Custom colors subject to additional charges, minimum quantities and extended lead times.
Consult representative. Custom color description:
© 2011 KIM LIGHTING INC.
• P.O. BOX 60080, CITY OF INDUSTRY, CA 91716-0080 • TEL: 626/968-5666 • FAX: 626/369-2

Type:
Job:
Wall Forms ® WF31C and WF31H
Half Face Recessed Mount, Round revision 6/17/11 • kl_wf3_spec1.pdf
Page: 3 of 3
Fusing
Cat. No.
SF
No Option
Quartz Standby
Cat. No.
QS
No Option
Emergency Battery
Back-up
Cat. No.
EM
No Option
Single Fusing (SF) for 120V, 277V, and 347V primary.
Integral electronic device energizes a T-4 mini-can socket during lamp warm-up and after power interruption. Socket de-energizes prior to the HID lamp reaching full brightness. T-4 mini-can halogen lamp by others; 100 watt maximum.
Internal battery pack provides 90 minutes of supplemental light at 750 lamp lumens on 42 watt compact fluorescent lamps only.
Battery Back-up
© 2011 KIM LIGHTING INC.
• P.O. BOX 60080, CITY OF INDUSTRY, CA 91716-0080 • TEL: 626/968-5666 • FAX: 626/369-2695