PROJECT:ITEM NO.:
CONTROL CENTER MODEL MS
SINGLE DIRECTION
SPECIFICATIONS
•Single direction only
• Push button ON/OFF switch
• High impact polycarbonate construction
• NEMA 4
• Magnetic starter/provides automatic shut-off in case of
power interruption
• Operates on line voltage
VOLTAGE/PHASE AVAILABILITY
Model
Phase
Disposer Models
1 Ph
SS-100 to SS-200
MS-8208-240V, 50/60 Hz
1 Ph
SS-100 to SS-200
MS-9208-240V, 50/60 Hz
3 Ph
SS-100 to SS-1000
MS-10380-460V, 50/60 Hz
3 Ph
SS-100 to SS-1000
MS-7
Voltage/Hz
120V, 50/60 Hz
ON-SITE
YEAR
RECOMMENDED INSTALLATION
PARTS & L ABOR
WARR ANT Y
DIMENSIONS
4-7/8”
(123.8 mm)
4-1/4”
(108.0 mm)
4”
(101.6 mm)
4-7/8”
(123.8 mm)
4-1/4”
(108.0 mm)
4-1/2”
(114.3 mm)
NOTE: Use a #8 screw to mount control.
A complete collection of our product drawings is available for download at the InSinkErator Revit/CAD
Library, which can be found at www.insinkerator.com/foodservice. Product information is also accessible
on The KCL CADalog. More information is available from KCL at www.kclcad.com.
4700 21st STREET
RACINE, WI 53406
TEL: 800-845-8345
FAX: 262 554-3620
www.insinkerator.com/foodservice
InSinkErator is a business unit of Emerson Electric Co.
The Emerson logo is a
trademark and a service mark
of Emerson Electric Co.
InSinkErator ©2016 Printed in USA
Form No. F452-16A-83-85
PROJECT:ITEM NO.:
CONTROL CENTER MODEL MRS
3-BUTTON • MANUAL REVERSE
SPECIFICATIONS
• 3-button switch with FWD/STOP/REV
• Stainless steel construction
• NEMA 4
•Manual reverse allows increased cutting element life
and reduces jams
•Magnetic starter/provides automatic shut-off in case of
power interruption
• Operates on line voltage
VOLTAGE/PHASE AVAILABILITY
Model
Phase
Disposer Models
MRS-14
120V, 50/60 Hz
Voltage/Hz
1 Ph
SS-100 to SS-200
MRS-15
208-240V, 50/60 Hz
1 Ph
SS-100 to SS-200
MRS-16
208-240V, 50/60 Hz
3 Ph
SS-100 to SS-1000
MRS-17
380-460V, 50/60 Hz
3 Ph
SS-100 to SS-1000
ON-SITE
YEAR
RECOMMENDED INSTALLATION
PARTS & L ABOR
WARR ANT Y
DIMENSIONS
6-3/4"
(171.5 mm)
4-1/2"
(114.3 mm)
5-1/4"
(133.4 mm)
1-1/2" (38.1 mm)
8-1/4"
(209.55 mm)
8-3/4"
(222.25 mm)
5-7/8"
(149.2 mm)
NOTE: The MRS control center should be mounted 1-1/2"
(38.1 mm) back from the front surface of the table.
A complete collection of our product drawings is available for download at the InSinkErator Revit/CAD
Library, which can be found at www.insinkerator.com/foodservice. Product information is also accessible
on The KCL CADalog. More information is available from KCL at www.kclcad.com.
4700 21st STREET
RACINE, WI 53406
TEL: 800-845-8345
FAX: 262 554-3620
www.insinkerator.com/foodservice
InSinkErator is a business unit of Emerson Electric Co.
The Emerson logo is a
trademark and a service mark
of Emerson Electric Co.
InSinkErator ©2016 Printed in USA
Form No. F453-16A-83-85
PROJECT:
ITEM NO.:
ELECTRICAL CONTROLS
SWITCHES
Manual Switch - MS
• Push button ON/OFF switch
• High impact polycarbonate construction
• NEMA 4 - water tight enclosure
• Single direction only
• Magnetic starter/provides automatic shut-off
in case of power interruption
• Operates on line voltage
Manual Reverse Switch - MRS
• 3 - Button switch with FWD/STOP/REV
• Stainless steel construction
• NEMA 4 - water tight enclosure
• Manual reverse allows increased cutting
element life and reduces jams
• Magnetic starter/provides automatic shut-off
in case of power interruption
• Operates on line voltage
• CUL approved switch
Low Voltage Switch - MSLV
• Push button ON/OFF switch
• Stainless steel construction
• NEMA 4 water tight enclosure
• Single direction only
• Line disconnect on front panel
• Magnetic starter/provides automatic shut-off
in case of power interruption
• Low voltage (24 volt) control circuit
ENCLOSURE DIMENSIONS ON REVERSE SIDE
4700 21st STREET
RACINE, WI 53406-5093
TEL: 800-558-5712 [Commercial Products]
FAX: 262-554-3620
www.insinkerator.com
In-Sink-Erator is a division of Emerson Electric Co.
The Emerson logo is a trademark and a
servicemark of Emerson Electric Co.
© IN-SINK-ERATOR
Printed in USA
Form No. C187-04E-02-02
ENCLOSURE DIMENSIONS (Inches)
4”
”
/8
47
MANUAL SWITCH – MS
4 7/8”
3/8”
between centerlines
41
/2”
(wit
/4”
hb
21
utto
(wit
hou 4”
t bu
t
ns)
11/16” from edge
to centerline
ton
s)
#6 3/8” panhead
self-tapping screws needed
MANUAL REVERSE SWITCH – MRS
”
/16
67
/2
41
om
” fr
LOW VOLTAGE SWITCH – MSLV
s
ine
terl
cen
mounting holes
5/16” in diameter
6"
1
/4" DIA.
HOLE (4)
5 1/2"
10 1/4"
10 3/4"
7 15/16”
8 9/16” from centerlines
8 1/4"
6 1/4"
/4”
63
51
/4”
PROJECT:ITEM NO.:
CONTROL CENTER MODEL CC-202
AUTOMATIC REVERSING ACTION • DOUBLES THE LIFE OF DISPOSER GRINDING ELEMENTS
SPECIFICATIONS
STAINLESS STEEL ENCLOSURE
• NEMA 4
• Stainless steel construction
• Easy to clean and keep clean
AUTOMATIC REVERSING CONTROL
• Reverses direction of motor at each startup
• Increases cutting element life and reduces jams
REVERSING DELAY
• Disposer will not reverse while motor is in motion
• Protects motor from burn out from operator misuse
AUTOMATIC DROP OUT SYSTEM
• If a power loss occurs, control will automatically disengage power lines
• Disposer must be restarted
VOLTAGE/PHASE AVAILABILITY
Model
Voltage/Hz
ON-SITE
Phase Disposer Models
CC202D-5
120V, 50/60 Hz
1 Ph
SS-100 to SS-200
CC202D-6
208-240V, 50/60 Hz
1 Ph
SS-100 to SS-200
CC202D-7
208-240V, 50/60 Hz
3 Ph
SS-100 to SS-1000
CC202D-8
380-460V, 50/60 Hz
3 Ph
SS-100 to SS-1000
RECOMMENDED INSTALLATION
YEAR
PARTS & L ABOR
WARR ANT Y
DIMENSIONS
8-1/4"
(209.6 mm)
6"
(152.4 mm)
10-3/4"
(273.1 mm)
10-1/4"
(260.4 mm)
5-1/4"
(133.4 mm)
5-7/8"
(149.2 mm)
NOTE: The CC-202 control center should be mounted 1-1/2"
(38.1 mm) back from the front surface of the table.
A complete collection of our product drawings is available for download at the InSinkErator Revit/CAD
Library, which can be found at www.insinkerator.com/foodservice. Product information is also accessible
on The KCL CADalog. More information is available from KCL at www.kclcad.com.
4700 21st STREET
RACINE, WI 53406
TEL: 800-845-8345
FAX: 262 554-3620
www.insinkerator.com/foodservice
InSinkErator is a business unit of Emerson Electric Co.
The Emerson logo is a
trademark and a service mark
of Emerson Electric Co.
InSinkErator ©2016 Printed in USA
Form No. F454-16A-83-85
PROJECT:ITEM NO.:
CONTROL CENTER MODEL CC-101
WATER/ENERGY SAVING FEATURE • AUTOMATIC REVERSING ACTION
SPECIFICATIONS
STAINLESS STEEL ENCLOSURE
• NEMA 4
• Stainless steel construction
• Easy to clean and keep clean
AUTOMATIC REVERSING CONTROL
• Reverses direction of motor at each startup
• Increases cutting element life and reduces jams
REVERSING DELAY
• Disposer will not reverse while motor is in motion
• Protects motor from burn out from operator misuse
AUTOMATIC DROP OUT SYSTEM
• If a power loss occurs, control will automatically
disengage power lines
• Disposer must be restarted
DISCONNECT SWITCH
• Disconnects electrical power beyond switch for service
• Interlock with front cover
SOLID STATE CONTROL
• Operates on 24V
SOLID STATE CONTROL CIRCUIT
•Printed circuit board with control diagnostic/function lights,
delay timers and timed run pin and reversing control
POST WATER FLUSH
• Adjustable timer allows water to run automatically for up
to 10 minutes, flushing disposer and drain lines after
disposer is shut off
TIMED RUN OR CONTINUOUS RUN
• Selected at your discretion, simply by moving the plug-in
in on the printed circuit board
•Timed run shuts off disposer automatically after 10 minutes
• Can be shut off manually any time
SOLENOID VALVE
• Packed unattached inside control center carton
• Ensures that water is flowing into disposer while disposer
is operating
ON-SITE
PARTS & L ABOR
YEAR
WARR ANT Y
DIMENSIONS
9-7/8"
(250.8 mm)
8-1/4"
(209.6 mm)
1"
(25.4 mm)
15-3/4"
(400.1 mm)
15-1/8"
(384.2 mm)
14"
(355.6 mm)
VOLTAGE/PHASE AVAILABILITY
Model
Voltage/Hz
Phase
Disposer Models
CC101K-5
120V, 50/60 Hz
1 Ph
SS-100 to SS-200
CC101K-6
208-240V, 50/60 Hz
1 Ph
SS-100 to SS-200
CC101K-7
208-240V, 50/60 Hz
3 Ph
SS-100 to SS-1000
CC101K-8
380-460V, 50/60 Hz
3 Ph
SS-100 to SS-1000
5-5/16"
(134.9 mm)
6-3/4"
(171.5 mm)
A complete collection of our product drawings is available for download at the InSinkErator Revit/CAD
Library, which can be found at www.insinkerator.com/foodservice. Product information is also accessible
on The KCL CADalog. More information is available from KCL at www.kclcad.com.
4700 21st STREET
RACINE, WI 53406
TEL: 800-845-8345
FAX: 262 554-3620
www.insinkerator.com/foodservice
InSinkErator is a business unit of Emerson Electric Co.
The Emerson logo is a
trademark and a service mark
of Emerson Electric Co.
InSinkErator ©2016 Printed in USA
Form No. F455-16A-83-85
RECOMMENDED INSTALLATION
NOTE: The CC-101 control center should be mounted 1-1/2" (38.1 mm) back from the front surface of the table.
PROJECT:ITEM NO.:
CONTROL CENTER MODEL AS-101
INDUSTRY EXCLUSIVE! WATER SAVING CONTROL CENTER
WATER SAVING FEATURES
• The AquaSaver® control center provides an on-demand water-saving
system for InSinkErator foodservice disposers
• The AS-101 control center senses the load of the disposer and regulates
the amount of water necessary for grinding and non-grinding situations
SPECIFICATIONS
STAINLESS STEEL ENCLOSURE
• NEMA 4
• Stainless steel construction
• Easy to clean and keep clean
AUTOMATIC REVERSING CONTROL
• Reverses direction of motor at each startup
• Increases cutting element life and reduces jams
REVERSING DELAY
• Disposer will not reverse while motor is in motion
• Protects motor from burn out from operator misuse
AUTOMATIC DROP OUT SYSTEM
• If a power loss occurs, control will automatically
disengage power lines
• Disposer must be restarted
DISCONNECT SWITCH
• Disconnects electrical power beyond switch for service
• Interlock with front cover
SOLID STATE CONTROL
• Operates on 24V
SOLID STATE CONTROL CIRCUIT
• Printed circuit board with control diagnostic/function lights,
delay timers and timed run pin and reversing control
POST WATER FLUSH
• Adjustable timer allows water to run automatically for
up to 10 minutes, flushing disposer and drain lines
after disposer is shut off
TIMED RUN OR CONTINUOUS RUN
• Selected at your discretion, simply by moving the plug-in pin
on the printed circuit board
• Timed run shuts off disposer automatically after 10 minutes
• Can be shut off manually any time
SOLENOID VALVE/FLOW CONTROL VALVE
• Two 24V solenoid valves included
• 1 GPM (3.8 LPM) and 7 GPM (26.5 LPM) flow control valves
included
ON-SITE *
YEAR
PARTS & L ABOR
WARR ANT Y
*Standard warranty is 1-year from date of installation. New AquaSaver® control
system installations that include a new disposer and new AS-101 control center
are eligible for a 3-year warranty on the entire system, including disposer.
DIMENSIONS
9-7/8”
(250.8 mm)
8-1/4”
(209.6 mm)
1”
(25.4 mm)
15-3/4”
(400.1 mm)
15-1/8”
(384.2 mm)
14”
(355.6 mm)
5-5/16”
(134.9 mm)
6-3/4”
(171.5 mm)
VOLTAGE/PHASE AVAILABILITY
Model
Voltage/Hz
Phase
Disposer Models
AS101K-5
120V, 50/60 Hz
1 Ph
SS-100 to SS-200
AS101K-6
208-240V, 50/60 Hz
1 Ph
SS-100 to SS-200
AS101K-7
208-240V, 50/60 Hz
3 Ph
SS-100 to SS-1000
AS101K-8
380-460V, 50/60 Hz
3 Ph
SS-100 to SS-1000
4700 21st STREET
RACINE, WI 53406
TEL: 800-845-8345
FAX: 262 554-3620
www.insinkerator.com/foodservice
InSinkErator is a business unit of Emerson Electric Co.
A complete collection of our product drawings is available
for download at the InSinkErator Revit/CAD Library, which
can be found at www.insinkerator.com/foodservice. Product
information is also accessible on The KCL CADalog. More
information is available from KCL at www.kclcad.com.
The Emerson logo is a
trademark and a service mark
of Emerson Electric Co.
InSinkErator ©2016 Printed in USA
Form No. F456-16A-83-85
TYPICAL TROUGH MOUNT APPLICATION
TYPICAL BOWL MOUNT APPLICATION
NOTE: The AquaSaver® control center should be mounted 1-1/2" (38.1 mm) back from the front surface of the table.
AS-101 FEATURES
Automatic
Reversing
Magnetic
Contactors
AquaSaver®
Sensor
Module
Post Water
Flush
Transformer
Timed Run or
Continuous
Run
Solid State
Control
Circuit
Line
Disconnect
Switch
Stainless
Steel
Enclosure