ASSEMBLY AND INSTALLATION
INSTRUCTIONS
PD55436 / PD55536 / PD55636 / PD55736
WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT
BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Figure.4
Outlet Box
Housing Grounding Wire
Screw
Loop lock
Mounting Plate
Green Grounding Screw
Fixture Grounding Wire
Mounting Screw
Upper Canopy
Lock Nut
Wire Nut
Fixture Wire
Twist the locking
tube to open or
close loop lock
Big Loop
Bolt Nut
Loop Lock
Chain
Figure.3
Suspension Rod
Big Loop
Frame
Hex Nut
Washer
Lower Canopy
Ring
Small Loop
Suspension Rod
Tube Assembly
Hex Nut
Washer
Coupling
Detail view for one
corner of the inside
frame
Hanger Bar
Threaded Pipe
Main Holder
Glass Holder
Frame
Glass Shade
Bulb Type A Max.100W
(not included)
Socket Ring
Page 1
100329
Figure.1
P-U
Figure.2
P-W
Figure.2-a
Clip
P-U (6pcs)
P-W (6pcs)
P-R (6pcs)
P-Z (6pcs)
P-S (6pcs)
P-U (12pcs)
P-W (6pcs)
(For All Items) (For All Items) (For PD55436) (For PD55536) (For PD55636) (For PD55736)
There are labels attached on the back of each silhouette, such
as P-Z, P-W, P-U, P-R and P-S.
Frame
Set Screw
P-U
P-W
P-Z
P-U
P-U
P-Z
P-W
P-U
P-W
1. Install the silhouettes onto the frame.
P-Z
(See Figure 1 & 2)
a. Take a silhouette and place it onto the
P-W
frame with the hole in the frame
aligning the slot in the clip of the
P-Z
silhouette, secure it with a set
P-U
P-W
Parts for
P-W
screw. (See Figure 2-a)
P-Z
PD55436
P-U
b. Repeat with the other silhouettes.
P-Z
P-U
P-U
c. There are labels attached on the back of
each silhouette, such as P-Z, P-W, P-U, P-R
Parts for
Parts for
PD55536
and P-S. Please follow the sequence shown in
PD55736
Figure 2 to install the silhouettes onto the frame.
d. You can install the silhouettes which marked P-R (for PD55436) or marked P-S (for PD55736) or
marked P-U & P-W (for PD55536) to the location of silhouettes which marked P-Z (for PD55636)
shown in Figure 2 to replace them.
2. Screw the threaded pipe into the coupling of the main holder, secure it with a washer and hex nut.
Then slide the tube assembly and lower canopy down through the threaded pipe and secure them
with a washer and hex nut.
Note: Make sure to keep the lower canopy parallel to the hanger bar.
3. Thread two screws through the mounting plate, and secure them with two lock nuts. Adjust the
length of the screws if necessary.
4. Attach the mounting plate to the outlet box by using two mounting screws.
5. Choose the length of the chains you need and adapt both chains to this length.
6. Take one loop lock, open the locking tube, then hook it onto the big loop of the upper canopy and
onto one end of the chain. Close back the locking tube of the loop lock. (See Figure.4)
7. Take another loop lock, open the locking tube, then hook it onto the big loop of the lower canopy and
onto the other end of one chain. Close back the locking tube of the loop lock. (See Figure.4)
8. Repeat steps 6~7 to connect the another chain to the upper canopy and lower canopy.
9. Thread the fixture wires and fixture grounding wire through one of the chains and out from the upper
canopy.
10. Cut any excess fixture wires and fixture grounding wire. Slit the two fixture wires apart in 5 inches.
Peel off insulation of the two wires in 5/8 inch.
11. Pull out the house supply wires and the house grounding wire from the outlet box. Make wire
connections using the wire nuts:
--- The smooth wire (marked) from the fixture to the black wire from the power source.
--- The ridged wire (unmarked) from the fixture to the white wire from the power source.
--- Attach the fixture grounding wire to the mounting strap with the green grounding screw. Then
connect it to the house grounding wire with a wire nut.
Carefully put the wires back into the outlet box.
12. Raise the upper canopy against the ceiling, with the screws located on the mounting plate
protruding from the holes in the upper canopy, secure it with two bolt nuts.
13. Take a suspension rod and hook one end onto the small loop of the lower canopy and hook another
end onto one ring located at a corner of the inside frame. (See Figure 3)
Repeat with the other suspension rods.
14. Attach the glass shades onto the glass holders, then secure them with socket rings.
15. Install bulbs (not included). See relamping label at socket area or packaging for maximum allowed
wattage.
16. Turn on the power at the main fuse or circuit breaker box.
Page 2
100329