AMPLIFIED CAPACITIVE SENSORS IN METAL HOUSING 12
÷
30 VDC NPN OR PNP OUTPUT
• Four wires, 12-30 VDC
• NPN - NO and NC
• PNP - NO and NC
• Adjustable range, 9-turn trimmer
• Nickel-plated brass
• Hight noise immunity
• Hight temperature stability
Identification code Wiring diagrams
CS
SERIES CS
NPN NO-NC output
PNP NO-NC output
NOMINAL SWITCHING DISTANCE (Sn)
NOMINAL VOLTAGE
RESIDUAL RIPPLE
HYSTERESIS
MAX. CURRENT OUTPUT
ABSORPTION AT 24 VDC
VOLTAGE DROP (Sensor ON)
OPERATION LED
SENSITIVITY ADJUSTMENT
SWITCHING FREQUENCY
START UP DELAY
REPEATABILITY (at even temperature)
SHORT CIRCUIT PROTECTION
ELECTRIC PROTECTIONS
TEMPERATURE LIMITS
PROTECTION DEGREE
CABLE LENGTH
CABLE SECTION
HOUSING MATERIAL
WEIGHT (Approximately)
09
10
09
15
16
SHIELDED NOT SHIELDED
1
÷
20 mm 1
÷
25 mm
12
÷
30 VDC (-15/+10%)
≤
10%
Depending on the sensing distance
200 mA
≤
20 mA
≤
1.8 V (I = 100 mA)
Yellow
Trimmer 9 turns
10 Hz
≤
100 mS
≤
5%
Present
Against polarity reversal - inductive loads
- 25
÷
+70
°
C
IP 67
2 m
4 x 0.25 mm2
Nickel-plated brass
250 g
NO NC
NPN
NO - NC
BROWN
BLACK
WHITE
BLUE
PNP
NO - NC
BROWN
BLACK
WHITE
BLUE
NC NO
Sensitivity adjustment
The sensitivity adjustment must be done when the sensor is installed in a definite and steady position.
The regulation must be done in a position half way between minimum and maximum, because, being air dielectric, a strong humidity variation could cause, if the regulation is very light, nuisance tripping.
The sensing distance of the sensor depends on the kind of material to detect and on its dimensions (see table about reduction factors).
The distance could change according to temperature variations.
To increase the sensitivity twist the trimmer clock-wise, to decrease do it anti clock-wise.
Models with cable output dimensions (mm)
SHIELDED MODELS
72 18
Sensitivity adjustment
LED
6
96 15
NOT SHIELDED MODELS
72
96
Ø 30 BACK VIEW
18
Sensitivity adjustment
LED
SENSITIVITY
ADJUST.
LED visible through transparence
-- +
6
CABLE
84
EMX INDUSTRIES INC.
AMPLIFIED CAPACITIVE SENSORS IN METAL HOUSING 18
÷
230 VAC-DC WITH TIMER RELAY OUTPUT
• Wide imput voltage, 18-230 VA/DC
• Relay SPDT output: 3A@30VAC, 1A@220VAC
• Timer, adjustable 1sec - 5 min
• Adjustable range
• Hight noise immunity
• Hight temperature stability
Identification code Wiring diagrams
CS 31 TE 5
R
E
L
A
Y
BROWN
WHITE
RED
BLACK
BLUE
SERIES CS
RELAY OUTPUT - Shielded
RELAY OUTPUT - Not shielded
ACTIVATING DELAY
DEACTIVATING DELAY
TIME: 1 sec
÷
5 min
31
32
TE
TD
L
N
Sensitivity adjustment
The sensitivity adjustment must be done when the sensor is installed in a definite and steady position.
The regulation must be done in a position half way between minimum and maximum, because, being air dielectric, a strong humidity variation could cause, if the regulation is very light, nuisance tripping.
The sensing distance of the sensor depends on the kind of material to detect and on its dimensions (see table about reduction factors).
The distance could change according to temperature variations.
To increase the sensitivity twist the trimmer clock-wise, to decrease do it anti clock-wise.
NOMINAL SWITCHING DISTANCE (Sn)
NOMINAL VOLTAGE
NET FREQUENCY
HYSTERESIS
OUTPUT
MAX. CURRENT OUTPUT
ABSORPTION
OPERATION LED
SENSITIVITY ADJUSTMENT
START UP DELAY
SWITCHING FREQUENCY
REPEATABILITY (at even temperature)
TEMPERATURE LIMITS
PROTECTION DEGREE
CABLE LENGTH
CABLE SECTION
HOUSING MATERIAL
WEIGHT (Approximately)
SHIELDED NOT SHIELDED
1
÷
20 mm 2
÷
30 mm
18
÷
230 VAC-DC (-15/+10%)
50
÷
60 Hz
Depending on the sensing distance
Relay (10 x106 ops. min.)
3A 30VAC - 1A 220VAC (90 W, 360 VA)
2.5 VA
Yellow
Trimmer 9 turns
≤
300 mS
10 Hz
≤
5%
- 25
÷
+70
°
C
IP 65
2 m
6 x 0.30 mm2
Nickel-plated brass
250 g
Time delay
To regulate the sensitivity of these models, reset the time delay trimmer before.
The available range of delay is :
1 SEC.
5 MIN.
SENSITIVITY ADJUST.
BACK VIEW
LED TIME ADJUST.
CABLE
Models with cable output dimensions (mm)
SHIELDED
72 18
SENSITIVITY
ADJUST.
LED
NOT SHIELDED
72 18
SENSITIVITY
ADJUST.
LED
110
85
15 110
EMX INDUSTRIES INC.