Salisbury by Honeywell
RUBBER & FIBER COVERUP
Class 3 Conductor Covers
•
•
•
•
•
5’ cover is ideal for covering long spans when weight is a consideration
26.4kV voltage rating
2” inside diameter
May be connected with Salisbury 1.5” I.D. Class 3 or 4 flexible cover-up equipment
Conductor covers connect easily with either plastic or rubber line hose
21172
5’ Cover with Eye
21173
27kV, 5’ Cover
21315
5’ Cover wtih 4’ Fiberglass Stick
21826
Lightweight 35kV, 6’ Conductor Cover
Straight Line Hose
• Orange Type II SALCOR® line hose wth RIB-GRIP® locking system
• Hoses remain flexible even in cold weather and are not damaged
by ozone or ultraviolet rays
• Other sizes and classes are available
Part #
Type
Class
I.D. x Length
OR125-3
II
2
1.25” x 3’
OR125-45
II
2
1.25” x 4.5’
OR125-6
II
2
1.25” x 6’
OR150-3
II
3
1.5” x 3’
OR150-6
II
3
1.5” x 6’
Part #
Type
Class
I.D. x Length
SU150-45C
II
4
1.5” x 4.5’
SU150-6C
II
4
1.5” x 6’
Line Hose - Extended Lip SU System
• The Extended Lip SU System is the only complete flexible
cover-up available for use on voltages through 34.5kV
• Extremely versatile, it may be installed by hand
• Manufactured from superior SALCOR® Type II elastomer it is
resistant to the effects of ozone and ultraviolet deterioration
• It remains flexible even at sub-zero temperatures
• Salisbury’s RIB GRIP® construction securely interlocks with its
corresponding covers and connectors
• Tapered lips facilitate easy starting on the conductors
• The contour cut ends accommodate the skirts of pin type
insulators and permit the hose to cover the line snug to a saddle
or clamp
• Available as Straight Line Hose or with a Connector End for
easier connection of line hose and covers
Stinger Cover
Protects against phase-to-phase and phase-to-ground wildlife contacts
Track resistant
May be installed without disconnecting the lead wire from the bushing
Easy to cut to the necessary length
Ozone and UV resistant SALCOR® elastomer
Part #
Description
38-50SC
3/8”x 50’ 1 coil
38-12SC
3/8” x 12’ 4 pcs
58-12SC
5/8” x 12’ coil 4 pcs
34-12SC
3/4” x 12’ coil 4 pcs
Part #
Description
21116
Cover Only; 16kV
21116TC
Cover with Tube Closure; 16kV
21644
Tube Closure
Silicon Bushing Cover
• Ozone and UV resistant silicone rubber
• Protects against wildlife contacts between energized equipment
and ground by insulating exposed energized bushing parts
• Interlock with the top weathershed of the bushing and are securely
fastened by inserting lock buttons
• Cover is 3.87” diameter x 3.37” tall
TRUSTED SINCE 1958
32
ltlutilitysupply.com
•
•
•
•
•
SU150-6C
RUBBER & FIBER COVERUP
Salisbury by Honeywell
1370 & 1371: Crossarm Guards
•
•
•
•
•
•
Available in two different styles: the 1370 pin type and the 1371 post type
Used to prevent tie wires from contacting crossarms during hot line operations
Two different tie downs provided: a neoprene and a polypropylene rope
Both are secured in the slots provided in the eye fitting
Post type model has an automatic gap closer which covers the insulator slot opening over the end of the arm
Made from orange Type I ABS cold weather high impact plastic
736PH: Slide-On Crossarm Guard
• Applied by sliding the cover on to the arm from the end using the shotgun eye until the unit locks onto the insulator pins
• Cover overlaps on top and has notches to ease application and removal
• Made from orange Type I ABS cold weather high impact plastic
Part #
Description
1370
1371
736PH
Dimensions
ASTM Voltage
Class
Weight (lbs)
Crossarm or Pin Type
Guard
9” x 9” x 25.5”
Fits Crossarm: 5 x 6
Crossarm or Post
Type Guard
4
5.7
4
6
Slide-On Crossarm
Guard
4
4.5
7”
Versa Guards® & Link Guards
• Make use of air as well as the dielectric strength of plastic to provide total insulating value
• Both guards have a 7” diameter and a hook shaped inner lip to keep the guard in place
• Versa Guards: voltage rating of 36.6kV are designed so that two guards can be coupled together to cover most 13kV single and
double arm, pin and post constructions
• Link Guards: voltage rating of 72.5kV, have inner and outer shells that run full length to include male and female couple ends
• Two guards connected provide four overlapping thicknesses of plastic plus air at a joint
• Tee Connectors: used on horizontal and vertical posts and suspension insulator strings when plastic line guards are used
on the conductor
• Available in two ratings: 72.5 kV and 48.3 kV
Part #
Description
Type
ASTM Voltage
Class
Grade
Weight
(lbs)
ltlutilitysupply.com
VERSA GUARDS 4.5’
2373
ABS/PVC, Eye
III
4
2
8.8
2377
ABS/PVC, 4’ Stick
III
4
1
10.8
2378
ABS/PVC, 6’ Stick
III
4
1
11.8
VERSA GUARDS 3.92’
2389
ABS/PVC, 4’ Stick
III
4
1
6.1
2689
ABS/PVC, Eye
III
4
2
8.1
LINK GUARDS 4.5’
2475
2373
2475
ABS/PVC, Eye
III
6
2
10.5
2476
ABS/PVC, 4’ Stick
III
6
1
12.5
2477
ABS/PVC, 6’ Stick
III
6
1
13.5
TRUSTED SINCE 1958
33
Salisbury by Honeywell
• Rated max use voltage of 48.3 kV guarded phase to guarded phase or 27kV phase to ground
• Unique Air Gap® Design: uniformly spaced dimples help increase insulation and keep electrical leakage to a minimum
• Type I ABS Plastic: strong memory improves grip when applied to the utility pole
Part #
Diameter x Length
Weight
2486
9” x 6’
13.8 lbs
2478
12” x 6’
16 lbs
Substation Cover-Up & Accessories
•
•
•
•
•
Often used where outages are difficult to reach and the occurrence of accidental contact is high
May be applied with rubber gloves or hot sticks
Made from Type I orange ABS plastic
Bus Guards: easily interlocked with each other, guard has voltage rating of 36.6kV
Bus “T” Guards: interlock two or three bus guards at bus tap “T” connections and 90° angles. To interlock units, first
position the bus guard then slide the “T” guard over the top interlocking the dimples. This guard has a voltage rating of 36.6kV
• Bus End Guards: cover the ends of a substation bus supported by station post insulators
9992
Part #
Dimensions
Description
ASTM Voltage
Class
Bus Guard 1374
5.25” x 9.5” x 4.5’
Impact Resistant ABS Plastic
4
6
Bus “T” Guard
1375
5” x 15” x 25”
Impact Resistant ABS Plastic
4
4
Bus End Guard
9992
8.5” x 12” x 24”
UV Resistant High Density
Cross Linked Polyethylene
3
5
816
8” x 16”
Hot Cover
4
2.5
4314
15” x 14.25”
Underground Distribution
Elbow Cover
3
2
4333
20” x 25”
Pole Bracket & Insulator Base
3
2.5
RUBBER & FIBER COVERUP
Class 5 Air Gap® Pole Guards
Weight (lbs)
GUARD ACCESSORIES
1374
TRUSTED SINCE 1958
34
ltlutilitysupply.com
1375
RUBBER & FIBER COVERUP
Salisbury by Honeywell
Post-Type Insulator Covers
PTHL
PTHS
• Covers interlock with 1.5” (38mm) Class 4
Extended Lip SU System or Conventional
Line Hose
• The PTHL cover also has external ribs on the
ears which secures 2.5” I.D. line hose
• Always use clamp pins to secure the device
into position
Part #
Description
PTHL
For insulators up to 16”
PTHS
For insulators up to 12”
Rubber Insulating Blanket - Slotted
• Ozone-resistant Type II orange SALCOR® is manufactured from a blend of prime EPDM, offering
supreme flexibility
• Use for covering ridge pins, cross arms with insulators or any place a wire, pin or projection interferes
with proper placement of other cover-up devices
1300
Class 4, 28 Eyelets, 36” x 36”
1302
Class 4, 2” Hole, 36” x 36”
1304
Class 4, 4.5” Hole, 36” x 36”
Rubber Insulating Blanket - Solid
• Ozone-resistant Type II orange SALCOR® is manufactured from a blend of prime EPDM, offering
supreme flexibilty
• Will maintain colour, flexibility, physical properties, and dielectric strength in the field longer than any
other blanket on the market
• Reinforced, beaded edge
Salisbury 900E
Class 4; 6 Eyelets; 36” x 36”
Roll Blanket
ltlutilitysupply.com
• Salisbury’s insulating Roll Blankets are made from a high strength fabric reinforced Type II rubber in unique colours making it
easy to identify and highly visible in the work area
• All classes of Roll Blankets are easy to cut, and flexible to -40°F. Highly puncture and tear resistant, each class of blanket is also
flame (self-extinguishing), oil, and ozone resistant
RLB00
ASTM 00, Type II, 3’ x 30’, Brown, 20 lbs
RLB0
ASTM 0, Type II, 3’ x 30’, Yellow, 26 lbs
RLB1
ASTM 1, Type II, 3’ x 30’, Yellow/Orange, 36 lbs
RLBPVC1
ASTM 1, 3’ x 50’, Clear, 60 lbs
RLBPVC1-48
ASTM 1, 4’ x 30’, Clear, 48 lbs
• The Roll Blankets can be easily custom-cut to fit each application at the job site
• This minimizes the number of different low voltage blanket sizes and shapes
that would otherwise need to be carried from job to job. Each blanket comes in a
convenient 36” wide roll
• Salisbury’s insulating Type II rubber Roll Blankets and Insulating Aprons, meet
ASTM F2320 standards
TRUSTED SINCE 1958
35
Salisbury by Honeywell
• Salisbury by Honeywell Arc Protection Blankets are now available in 4’ x 5’ and 4’ x 8’ sizes
• Each size is available in 15kA or 40kA ratings. The 15kA blankets include convenient loops and the 40kA blankets include
grommets to easily keep the blanket in place
• These new blankets are sold individually or with a storage bag or storage bag and tie-strap kit
• The Arc Suppression Blanket is used as a barrier for protection from the explosive and incendiary effects of electrical arcs and
flashes. These hazardous electrical discharges can be caused by faults in cables, in cable splices and joints, and at transformer
terminals, or they may be generated by the operation of switchgear, circuit breakers and lightning arresters
• The blanket can be used for worker protection in underground vaults, switchyards, and other locations where electrical
equipment poses a risk of exposure to explosive electrical discharges
NOTE: These products do not eliminate or reduce requirements for proper PPE for arc flash protection
Blanket Pins
Part #
Dimensions
Description
ARC45-15
48” x 60”
15kA rating - navy blue
ARC45-40
48” x 60”
40kA rating -gray/khaki
ARC48-15
48” x 96”
15kA rating - navy blue
ARC48-40
48” x 96”
40kA rating -gray/khaki
RUBBER & FIBER COVERUP
Arc Protection Blankets
• In addition to other uses, blanket clamp pins can be used to hold insulating blankets in place
• Springs are used for tension while extra holes in the body of the pin are used to grip conductors and
prevent line hose from sliding
• Opens to a full 5.5”, making these pins the most versatile on the market
• Tapered ends to accommodate any clampstick
• Fiberglass reinforced nylon with rubber tipped pin boots
• Use HS21 for applications and removal where a 90° angle is necessary
Salisbury 21
Salisbury HS21 For 90o Angle Applications
Blanket Buttons
• Designed to secure eyelet-style insulating
blanket
• Made of yellow plastic, these buttons
snap through the eyelet with thumb
pressure on the large head
• 9” x 37”; holds up to six 36” blankets
• Molded in bright orange, high impact
polyethylene with a tight fitting cap
• For easy retrieval, blankets can be rolled
individually and stored in canister; a single
blanket can then be removed without
removing any others
P2
Fits Blanket Max Size: 36”, Dimensions (in): 5 x 37,
Capacity: 1-2 Blankets
P4
Fits Blanket Max Size: 36”, Dimensions (in): 7 x 37,
Capacity: 1-4 Blankets
P6
Fits Blanket Max Size: 36”, Dimensions (in): 9 x 37,
Capacity: 1-6 Blankets
Salisbury B1
36
ltlutilitysupply.com
Blanket Canisters
RUBBER & FIBER COVERUP
Chance - Rubber Insulating Covers
36” x 36” Rubber Insulating Blankets
Rubber Blanket Buttons
• Sold individually
• For use with any rubber insulating
blanket with perimeter eyelets
C4060532
•
•
•
•
Class 4
Will retain its high-visibility orange colour
Clamp Pins
May be used in applications which require a lower class or type
• C4060530 features eyes and special handle shape for easy
Type II ozone/corona-resistant elastomer offers excellent
placement by clampstick
performance properties in accordance with ASTM Standard
• C4060531 features a special handle shape for easy
Specification D-1048
placement by clampstick
• Offers superior resistance to long-term aging/checking
C4060346
Solid Blanket
6 eyelets
C4060348
Slotted Blanket
28 eyelets
C4060530
Rubber Glove Use
C4060531
Hot Stick Use
Straight Line Hose
• Does not absorb water
• Type II ozone/corona-resistant elastometer offers excellent
performance properties in accordance with ASTM
Standard Specification D-1050-90
C4060296
Class 2, 1.25” diameter, 6’ length, 4.55 lbs
C4060299
Class 3, 1.5” diameter, 6’ length, 6.22 lbs.
Short-Lip Flexible Line Hose
• Does not absorb water
• Type II ozone/corona-resistant elastometer offers excellent
performance properties in accordance with ASTM Standard
Specification D-1050-90
C4060306
Class 2, 1.25” diameter, 6’ long coupler on one end; proof
tested at 20kV AC RMS
C4060309
Class 3, 1.25” diameter, 6’ long coupler on one end; proof
tested at 30kV AC RMS
ltlutilitysupply.com
Deadend Cover
• These covers provide a highly versatile system of covering up
a wide variety of configurations on distribution systems
• The conductor covers couple with the insulator units and
deadend units to cover pin-type or post- type insulator
construction, virtually surrounding the hot parts and
hardware to give line workers extra protection when rubber
gloving or using hot sticks
• Each item is fitted with an adapter for multi-position handling
by Grip-All clampsticks
• Covers couple with Chance 25kV covers, Classes 2, 3, and 4 of
rubber line hose and major brands of rubber insulator hoods
• All covers are bright orange in colour
• All are made of high density polyethylene in a uniform wall
thickness for excellent dielectric/puncture strength
• Performs well from -50° to 170°F
• Ultra-violet stabilizers in the material help inhibit degradation
as a result of atmospheric exposure
• Deadend cover fits three 10” diameter porcelain bells or
polymer deadend insulators and couples with the line cover
• To meet the Class 4 rating, the deadend cover must be used in
conjunction with a rubber insulating blanket covering the
coupler to the line cover
• Failure to use a blanket to cover the coupler may result in
electrical shock, severe injury or death by electrocution
Spiral Conductor Cover
• Provides extra protection with a wide air space between
two thicknesses of solid insulation
• Made of tough, durable ABS plastic
• Overall length of each cover is 53”
• All units interlock with eachother to make up a chain of
guards
• 15/36.6 kV units are formed on the ends to fit over
most 15kV insulators, thus eliminating the need for
an insulator cover
• A 4’ or 6’ long retractable Epoxiglas® handle or
Clampstick adapter provides for ease of installation
from a bucket or platform, in single units or
linked together
• Each double-crossarm unit will fit over two 15kV pintype insulators
C4060082GA
C4060537
TRUSTED SINCE 1958
37
46kV Phase-to-Phase
36kV Phase-to-Phase
Chance - Rubber Insulating Covers
•
•
•
•
•
•
Prolonged contact with an energized conductor must not be allowed
Tested to ASTM F712
Manufactured to ASTM F968 specifications
Meet Class 4 requirements
Made of high dielectric linear polyethylene material that will not flash flame
Helps protect personnel when raising or lowering a pole between energized lines or to cover poles when rubber glove
maintenance is performed in relatively confined areas
• This material will have some softening without deformation at approximately 170°F, and it will resist brittleness at
temperatures to -50°F
• Chance covers are ribbed to reduce cover contact with the pole, thus minimizing creosote contamination
• Rope handles permit personnel to easily spread the covers and snap them around the pole; rubber gloves must be worn
during this procedure
6” Diameter Pole Covers
12” Diameter Pole Covers
9” Diameter Pole Covers
C4060550
48” long
M4937-1
12” long
C4060029
24” long
C4060551
72” long
M4937-2
24” long
C4060030
48” long
M4937-4
48” long
C4060000
72” long
M4937-6
72” long
RUBBER & FIBER COVERUP
Pole Covers
Conductor Cover & Insulator Covers
rs
•
•
•
•
•
•
•
•
•
•
Bright orange in colour
5’ long; 25 kV phase-to-phase
Maximum conductor size: 666 kcmil ACSR
Performs well from -50° to 170°F
Available with adapter for hot stick application or without adapter for rubber glove application
Provide a highly versatile system of covering up a wide variety of configurations on distribution systems; the units virtually
surround the hot parts and hardware to give the linemen extra protection when rubber gloving or using hot sticks
Made of high density polyethylene in a uniform wall thickness for excellent dielectric/puncture strength
5’ long and are available with a Grip-All adapter for hot stick application or without adapter for rubber glove application
Conductor covers mate with insulator covers to cover pin-type or post-type insulator construction; may also be used with the
deadend cover
Conductor cover will couple with major brands of rubber line hose and insulator covers of the 25kV class
25 kV Phase-to-Phase
36 kV Phase-to-Phase
C4060181
5’ Cover, 4’ Handle
C4060514GA
C4060181GA
5’ Cover, Grip-All Adapter
P4060184
5’ Cover Only
5’ Cover, Grip-All Adapter
Insulator Covers
• Prevents tie wires from contacting the crossarm when
tying and untying insulators
• The material used is the same high-dielectric
polyethelyne used for Chance conductor and
insulator covers
• Flanges above the slots shield the ends of the
double-arming bolts
• Designed for single or double arm construction, with slots
provided for double-arming bolts
• Insulator covers come in two heights; 12” or 16.5”
• Cover fits 6.5” to 9” diameter pin or post insulators
• Special slits in the insulator covers help locate the conductor and
hardware when installing the covers
C4060557
12” Tall
36 kV Phase-to-Phase
C4060557L
16.5” Tall
36 kV Phase-to-Phase
M4933
TRUSTED SINCE 1958
38
ltlutilitysupply.com
Cross Arm Cover