Die Sets, Guide Pillars, Bushes, Die
Springs and Urethane
www.awprecision.com
A Company Introduction
AW PRECISION is one of Europe’s largest producers
of punches, dies and Die Sets. Along with an extensive
selection of Tooling Accessories, Kaller® Gas Springs,
Cam Units, Urethane and Guide Elements we are your
‘One-Stop’ shop for all your tooling requirements.
AW PRECISION can offer…
Short, consistent delivery times on most standard and nonstandard products helping you to maintain a continuous
level of production.
Broad range of products
AW Precision’s vast product range simplifies the process
of purchasing tools for the increasingly busy tool maker.
Contents
Die Sets
Pages 2 - 23
Introduction
Standard Die Sets with centre pillars
Standard Shaped Die sets with diagonal pillars
Standard Die Sets with rear pillars
Page
Page
2
3–5
6
7–9
Stripper Plate – Demountable Guide Bushes &
Ball Bearing Cages
31
Demountable Guide Bushes for use with Ball
Bearing Cages
32
Ball Bearing Cages
33
Guide to operating conditions
– Type 1
34
Selection table for Bush and Ball Cage – Type 1
35
Standard Die Sets with diagonal pillars
10–11
Guide to operating conditions
– Type 2
36
Standard Die Sets with four pillars
12–13
Selection table for Bush and Ball Cage – Type 2
37
Standard Die Sets with centre pillars and ball
bearing guide bushes
14–15
Pillar Assembly Data
38
Standard Die Sets with rear pillars and ball
bearing guide bushes
16–17
Bush Assembly Data
39
Standard Die Sets with diagonal pillars and
ball bearing guide bushes
18–19
Pillar and Bush Accessories
40
Standard Die Sets with four pillars and ball
bearing guide bushes
20–21
Standard Shanks & Setting Posts
22
SPECIAL DIE SETS
23
Guide Elements
Pages 24 - 40
Die Springs
Pages 41 - 44
Light Load Springs
41
Intermediate Load Springs
42
Heavy Load Springs
43
Guide Pillars
24
Extra Heavy Load Springs
44
Standard Die Set Demountable Guide Bushes
25
Urethane Rod
45
Demountable Guide Pillars – with fixing clamps
26
Urethane Tubes
45
Demountable Guide Pillars – with central fixing
27
Urethane Strippers
46
Demountable Guide Bushes – Plain and
Bronze lined
28
Spring Retainers
46
Demountable Guide Bushes – Plain and
Bronze lined
29
Urethane Springs
47
Straight Sleeve Ball Bearing Bushes
30
Urethane Sheet and Blocks
48
2012
3
Standard Die Sets
Introduction
The AW Precision range of Standard Die Sets has been formulated with the needs of the modern
toolmaker and tool design engineer taken into account.
Our Standard Die Sets are manufactured on the latest generation CNC machining centres,
which are recognised for their high accuracy and repeatability, thus ensuring a high quality
product.
To further ensure the accuracy of our Standard Die Sets we adopt a selective fit policy for our
pillars and guide bushes. This provides for uniform clearance in each guiding assembly and
consistency throughout the die set assembly. The three classes of fit are:
Class 1For very fine clearance between punch and die sections. Where clearance per side
is less than 0.02 mm. Normally used for very thin stock materials.
Class 2 For punch and die sections where a clearance per side of 0.02 mm to 0.06 mm is
required. For tooling processing stock material thicknesses in excess of 0.4 mm.
Class 3 For punch and die sections where clearance per side is in excess of 0.08 mm.
NOTE Class 2 is supplied as standard.
All Standard Die Sets are manufactured from stress relieved mild steel (BS 4360-43A) and fitted
with precision ground pillars and guide bushes.
AW Precision Standard Die Set range comprises:
● Demountable bushes
● Straight guide pillars
● Four die set designs
● 132 different die set sizes
● 1257 different die sets
● Available with solid guiding (plain or bronze plated) or ball bearing guiding
● One rear pillar offset 2mm on four pillar sets
● Intermediate plate option
4
Standard Die Sets with Centre Pillars D61.xxx.xxx
D71.xxx.xxx
C2
E
C2
L
C3
P
B
C1
C1
Standard Die Set with stripper plate
Ref. No.: D61.xxx.xxx
A
Standard Die Set
Ref. No.: D71.xxx.xxx
A1
To order specify Die Set Reference No. and Pillar Length (L = see page 24)
Example: D71.012.012 – L=160
External
Dimensions
REFERENCE NUMBER
3 Plate
2 Plate
STANDARD ASSEMBLY
Die Space
A
D61.010.008 D71.010.008 225
B
A1
80
100
C1 ± 2 C 2 ± 2 C 3 ± 2
32
25
25
E
P
147
39
D61.012.008 D71.012.008 250
80
125
32
25
25
172
39
D61.016.008 D71.016.008 285
80
160
32
25
25
207
39
D61.020.008 D71.020.008 325
80
200
32
25
25
247
39
D61.010.010 D71.010.010 225
100
100
32
25
25
147
39
D61.012.010 D71.012.010 250
100
125
32
25
25
172
39
D61.016.010 D71.016.010 285
100
160
32
25
25
207
39
D61.025.010 D71.025.010 390
100
250
40
32
28
304
43
D61.012.012 D71.012.012 265
125
125
40
32
28
179
43
D61.016.012 D71.016.012 300
125
160
40
32
32
214
43
D61.020.012 D71.020.012 340
125
200
50
40
32
254
43
D61.031.012 D71.031.012 455
125
315
50
40
32
369
43
D61.016.016 D71.016.016 300
160
160
50
40
32
214
43
D61.020.016 D71.020.016 340
160
200
50
40
32
254
43
D61.025.016 D71.025.016 390
160
250
50
40
32
304
43
D61.031.016 D71.031.016 455
160
315
50
40
32
369
43
Pillars
Bushes
P10.024.xxx B10.024.050
P10.025.xxx B10.025.050
P10.030.xxx B10.030.050
P10.032.xxx B10.032.050
Demountable Pillars and/or Bronze Plated Bushes may be specified and fitted at additional cost.
(Refer to Pillar & Bush Section)
5
D81.xxx.xxx
D91.xxx.xxx
Standard Die Sets with Centre Pillars
C2
L
C3
B
A1
C1
C1
P
E
C2
Standard Die Set with stripper plate
Ref. No.: D81.xxx.xxx
A
Standard Die Set
Ref. No.: D91.xxx.xxx
External
Dimensions
REFERENCE NUMBER
3 Plate
2 Plate
D81.125.016 D91.125.016
D81.225.016 D91.225.016
D81.325.016 D91.325.016
D81.425.016 D91.425.016
D81.125.020 D91.125.020
D81.225.020 D91.225.020
D81.325.020 D91.325.020
D81.425.020 D91.425.020
D81.125.025 D91.125.025
D81.225.025 D91.225.025
D81.325.025 D91.325.025
D81.425.025 D91.425.025
D81.131.020 D91.131.020
D81.231.020 D91.231.020
D81.331.020 D91.331.020
D81.431.020 D91.431.020
D81.131.025 D91.131.025
D81.231.025 D91.231.025
D81.331.025 D91.331.025
D81.431.025 D91.431.025
D81.131.031 D91.131.031
D81.231.031 D91.231.031
D81.331.031 D91.331.031
D81.431.031 D91.431.031
D81.140.020 D91.140.020
D81.240.020 D91.240.020
D81.340.020 D91.340.020
D81.440.020 D91.440.020
D81.140.025 D91.140.025
D81.240.025 D91.240.025
D81.340.025 D91.340.025
D81.440.025 D91.440.025
D81.140.031 D91.140.031
D81.240.031 D91.240.031
D81.340.031 D91.340.031
D81.440.031 D91.440.031
D81.140.040 D91.140.040
D81.240.040 D91.240.040
D81.340.040 D91.340.040
6
A
250
250
250
250
250
250
250
250
250
250
250
250
315
315
315
315
315
315
315
315
315
315
315
315
400
400
400
400
400
400
400
400
400
400
400
400
400
400
400
Die Space
B
A 1 C1 ± 2 C 2 ± 2 C 3 ± 2
160 127
32
32
32
160 127
32
40
32
160 127
40
32
32
160 127
40
40
32
200 127
32
32
32
200 127
32
40
32
200 127
40
32
32
200 127
40
40
32
250 127
32
32
32
250 127
32
40
32
250 127
40
32
32
250 127
40
40
32
200 171
40
40
32
200 171
40
50
32
200 171
50
40
32
200 171
50
50
32
250 171
40
40
32
250 171
40
50
32
250 171
50
40
32
250 171
50
50
32
315 171
40
40
32
315 171
40
50
32
315 171
50
40
32
315 171
50
50
32
200 256
40
40
32
200 256
40
50
32
200 256
50
40
32
200 256
50
50
32
250 256
40
40
32
250 256
40
50
32
250 256
50
40
32
250 256
50
50
32
315 256
40
40
32
315 256
40
50
32
315 256
50
40
32
315 256
50
50
32
400 256
40
40
32
400 256
40
50
32
400 256
50
40
32
E
174
174
174
174
174
174
174
174
174
174
174
174
225
225
225
225
225
225
225
225
225
225
225
225
310
310
310
310
310
310
310
310
310
310
310
310
310
310
310
P
38
38
38
38
38
38
38
38
38
38
38
38
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
STANDARD ASSEMBLY
Pillars
Bushes
P10.024.xxx B10.024.050
P10.025.xxx B10.025.050
P10.030.xxx B10.030.050
P10.032.xxx B10.032.050
Standard Die Sets with Centre Pillars D81.xxx.xxx
D91.xxx.xxx
To order specify Die Set Reference No. and Pillar Length (L = see page 24)
Example: D91.163.031 – L=280
External
Dimensions
REFERENCE NUMBER
3 Plate
D81.150.025
D81.250.025
D81.350.025
D81.450.025
D81.150.031
D81.250.031
D81.350.031
D81.450.031
D81.150.040
D81.250.040
D81.350.040
D81.450.040
D81.150.050
D81.250.050
D81.350.050
D81.450.050
D81.163.031
D81.263.031
D81.363.031
D81.463.031
D81.163.040
D81.263.040
D81.363.040
D81.463.040
D81.163.050
D81.263.050
D81.363.050
D81.463.050
D81.163.063
D81.263.063
D81.363.063
D81.463.063
D81.171.040
D81.271.040
D81.371.040
D81.471.040
D81.171.050
D81.271.050
D81.371.050
D81.471.050
D81.171.063
D81.271.063
D81.371.063
2 Plate
D91.150.025
D91.250.025
D91.350.025
D91.450.025
D91.150.031
D91.250.031
D91.350.031
D91.450.031
D91.150.040
D91.250.040
D91.350.040
D91.450.040
D91.150.050
D91.250.050
D91.350.050
D91.450.050
D91.163.031
D91.263.031
D91.363.031
D91.463.031
D91.163.040
D91.263.040
D91.363.040
D91.463.040
D91.163.050
D91.263.050
D91.363.050
D91.463.050
D91.163.063
D91.263.063
D91.363.063
D91.463.063
D91.171.040
D91.271.040
D91.371.040
D91.471.040
D91.171.050
D91.271.050
D91.371.050
D91.471.050
D91.171.063
D91.271.063
D91.371.063
STANDARD ASSEMBLY
Die Space
A
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
630
630
630
630
630
630
630
630
630
630
630
630
630
630
630
630
710
710
710
710
710
710
710
710
710
710
710
B
250
250
250
250
315
315
315
315
400
400
400
400
500
500
500
500
315
315
315
315
400
400
400
400
500
500
500
500
630
630
630
630
400
400
400
400
500
500
500
500
630
630
630
A 1 C1 ± 2 C 2 ± 2 C 3 ± 2
337
40
40
32
337
40
50
32
337
50
40
32
337
50
50
32
337
40
40
32
337
40
50
32
337
50
40
32
337
50
50
32
337
40
40
32
337
40
50
32
337
50
40
32
337
50
50
32
337
40
40
32
337
40
50
32
337
50
40
32
337
50
50
32
435
50
50
40
435
50
58
40
435
58
50
40
435
58
58
40
435
50
50
40
435
50
58
40
435
58
50
40
435
58
58
40
435
50
50
40
435
50
58
40
435
58
50
40
435
58
58
40
435
50
50
40
435
50
58
40
435
58
50
40
435
58
58
40
515
58
58
40
515
58
63
40
515
63
58
40
515
63
63
40
515
58
58
40
515
58
63
40
515
63
58
40
515
63
63
40
515
58
58
40
515
58
63
40
515
63
58
40
E
400
400
400
400
400
400
400
400
400
400
400
400
400
400
400
400
510
510
510
510
510
510
510
510
510
510
510
510
510
510
510
510
590
590
590
590
590
590
590
590
590
590
590
P
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
Pillars
Bushes
P10.038.xxx B10.038.050
P10.040.xxx B10.040.050
P10.048.xxx B10.048.050
P10.050.xxx B10.050.050
Demountable Pillars and/or Bronze Plated Brushes may be specified and fitted at additional cost.
(Refer to Pillar & Bush Section)
7
D72.xxx.xxx
Standard Die Sets with Rear Pillars
P
E
P
C2
B
L
B1
C1
A
Standard Die Set
Ref. No.: D72.xxx.xxx
To order specify Die Set Reference No. and Pillar Length (L = see page 24)
Example: D72.025.010 – L=160
External
Dimensions
STANDARD ASSEMBLY
Die Space
REFERENCE
NUMBER
B
A
B1
E
P
D72.012.006
108
125
63
25
20
69
28
D72.016.006
108
160
63
25
20
104
28
D72.020.006
108
200
63
25
20
144
28
D72.016.008
143
160
80
32
25
82
39
C1 ± 2 C 2 ± 2
D72.020.008
143
200
80
32
25
122
39
D72.025.008
143
250
80
32
25
172
39
D72.020.010
163
200
100
40
32
122
39
D72.025.010
163
250
100
40
32
172
39
D72.031.010
163
315
100
40
32
237
39
D72.020.012
195
200
125
40
32
114
43
D72.025.012
195
250
125
40
32
164
43
D72.031.012
195
315
125
40
32
229
43
D72.025.016
230
250
160
50
40
164
43
D72.031.016
230
315
160
50
40
229
43
Pillars
Bushes
P10.020.xxx B10.020.032
P10.025.xxx B10.025.050
P10.032.xxx B10.032.050
Demountable Pillars and/or Bronze Plated Bushes may be specified and fitted at additional cost.
(Refer to Pillar & Bush Section)
8
Standard Die Sets with Rear Pillars D92.xxx.xxx
E
P
P
C2
B
L
B1
C1
A
Standard Die Set
Ref. No.: D92.xxx.xxx
External
Dimensions
REFERENCE
NUMBER
D92.125.016
D92.225.016
D92.325.016
D92.425.016
D92.125.020
D92.225.020
D92.325.020
D92.425.020
D92.125.025
D92.225.025
D92.325.025
D92.425.025
D92.131.020
D92.231.020
D92.331.020
D92.431.020
D92.131.025
D92.231.025
D92.331.025
D92.431.025
D92.131.031
D92.231.031
D92.331.031
D92.431.031
D92.140.020
D92.240.020
D92.340.020
D92.440.020
D92.140.025
D92.240.025
D92.340.025
D92.440.025
D92.140.031
D92.240.031
D92.340.031
D92.440.031
STANDARD ASSEMBLY
Die Space
B
160
160
160
160
200
200
200
200
250
250
250
250
200
200
200
200
250
250
250
250
315
315
315
315
200
200
200
200
250
250
250
250
315
315
315
315
A
250
250
250
250
250
250
250
250
250
250
250
250
315
315
315
315
315
315
315
315
315
315
315
315
400
400
400
400
400
400
400
400
400
400
400
400
B 1 C1 ± 2 C 2 ± 2
98
32
32
98
32
40
98
40
32
98
40
40
138
32
32
138
32
40
138
40
32
138
40
40
188
32
32
188
32
40
188
40
32
188
40
40
128
32
32
128
32
40
128
40
32
128
40
40
178
32
32
178
32
40
178
40
32
178
40
40
243
40
40
243
40
50
243
50
40
243
50
50
128
40
40
128
40
50
128
50
40
128
50
50
178
40
40
178
40
50
178
50
40
178
50
50
243
40
40
243
40
50
243
50
40
243
50
50
E
174
174
174
174
174
174
174
174
174
174
174
174
225
225
225
225
225
225
225
225
225
225
225
225
310
310
310
310
310
310
310
310
310
310
310
310
P
38
38
38
38
38
38
38
38
38
38
38
38
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
Pillars
Bushes
P10.025.xxx B10.025.050
P10.032.xxx B10.032.050
9
D92.xxx.xxx
Standard Die Sets with Rear Pillars
To order specify Die Set Reference No. and Pillar Length (L = see page 24)
Example: D92.325.025 – L=180
External
Dimensions
REFERENCE
NUMBER
D92.150.025
D92.250.025
D92.350.025
D92.450.025
D92.150.031
D92.250.031
D92.350.031
D92.450.031
D92.150.040
D92.250.040
D92.350.040
D92.450.040
D92.150.050
D92.250.050
D92.350.050
D92.450.050
STANDARD ASSEMBLY
Die Space
B
250
250
250
250
315
315
315
315
400
400
400
400
500
500
500
500
A
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
B 1 C1 ± 2 C 2 ± 2
168
40
40
168
40
50
168
50
40
168
50
50
233
40
40
233
40
50
233
50
40
233
50
50
318
40
40
318
40
50
318
50
40
318
50
50
418
40
40
418
40
50
418
50
40
418
50
50
E
400
400
400
400
400
400
400
400
400
400
400
400
400
400
400
400
P
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
Pillars
Bushes
P10.040.xxx B10.040.050
Demountable Pillars and/or Bronze Plated Bushes may be specified and fitted at additional cost.
(Refer to Pillar & Bush Section)
10
Standard Die Sets with Diagonal Pillars D83.xxx.xxx
D93.xxx.xxx
C2
E
C2
P
L
C3
P
B E1
A1
B1
C1
C1
Standard Die Set with stripper plate
Ref. No.: D83.xxx.xxx
A
Standard Die Set
Ref. No.: D93.xxx.xxx
External Dimensions
REFERENCE
NUMBER
3 Plate
D83.125.016
D83.225.016
D83.325.016
D83.425.016
D83.125.020
D83.225.020
D83.325.020
D83.425.020
D83.125.025
D83.225.025
D83.325.025
D83.425.025
2 Plate
D93.125.016
D93.225.016
D93.325.016
D93.425.016
D93.125.020
D93.225.020
D93.325.020
D93.425.020
D93.125.025
D93.225.025
D93.325.025
D93.425.025
STANDARD
ASSEMBLY
Die Space Die Space
A
250
250
250
250
250
250
250
250
250
250
250
250
B1
37
37
37
37
77
77
77
77
127
127
127
127
B
160
160
160
160
200
200
200
200
250
250
250
250
A 1 C1 ± 2 C 2 ± 2 C 3 ± 2
127 32
32
32
127 32
40
32
127 40
32
32
127 40
40
32
127 32
32
32
127 32
40
32
127 40
32
32
127 40
40
32
127 32
32
32
127 32
40
32
127 40
32
32
127 40
40
32
E
174
174
174
174
174
174
174
174
174
174
174
174
E1
84
84
84
84
124
124
124
124
174
174
174
174
P
Pillars
Bushes
38
38
38
38
38
38 P10.024.xxx B10.024.050
38 P10.025.xxx B10.025.050
38
38
38
38
38
11
D83.xxx.xxx
D93.xxx.xxx
Standard Die Sets with Diagonal Pillars
To order specify Die Set Reference No. and Pillar Length (L = see page 24)
Example: D93.363.063 – L=315
External Dimensions
REFERENCE
NUMBER
3 Plate
D83.150.025
D83.250.025
D83.350.025
D83.450.025
D83.150.031
D83.250.031
D83.350.031
D83.450.031
D83.150.040
D83.250.040
D83.350.040
D83.450.040
D83.150.050
D83.250.050
D83.350.050
D83.450.050
D83.163.031
D83.263.031
D83.363.031
D83.463.031
D83.163.040
D83.263.040
D83.363.040
D83.463.040
D83.163.050
D83.263.050
D83.363.050
D83.463.050
D83.163.063
D83.263.063
D83.363.063
D83.463.063
D83.171.040
D83.271.040
D83.371.040
D83.471.040
D83.171.050
D83.271.050
D83.371.050
D83.471.050
D83.171.063
D83.271.063
D83.371.063
D83.471.063
2 Plate
D93.150.025
D93.250.025
D93.350.025
D93.450.025
D93.150.031
D93.250.031
D93.350.031
D93.450.031
D93.150.040
D93.250.040
D93.350.040
D93.450.040
D93.150.050
D93.250.050
D93.350.050
D93.450.050
D93.163.031
D93.263.031
D93.363.031
D93.463.031
D93.163.040
D93.263.040
D93.363.040
D93.463.040
D93.163.050
D93.263.050
D93.363.050
D93.463.050
D93.163.063
D93.263.063
D93.363.063
D93.463.063
D93.171.040
D93.271.040
D93.371.040
D93.471.040
D93.171.050
D93.271.050
D93.371.050
D93.471.050
D93.171.063
D93.271.063
D93.371.063
D93.471.063
STANDARD
ASSEMBLY
Die Space Die Space
A
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
630
630
630
630
630
630
630
630
630
630
630
630
630
630
630
630
710
710
710
710
710
710
710
710
710
710
710
710
B1
87
87
87
87
152
152
152
152
237
237
237
237
337
337
337
337
120
120
120
120
205
205
205
205
305
305
305
305
435
435
435
435
205
205
205
205
305
305
305
305
435
435
435
435
B
250
250
250
250
315
315
315
315
400
400
400
400
500
500
500
500
315
315
315
315
400
400
400
400
500
500
500
500
630
630
630
630
400
400
400
400
500
500
500
500
630
630
630
630
A 1 C1 ± 2 C 2 ± 2 C 3 ± 2
337 40
40
32
337 40
50
32
337 50
40
32
337 50
50
32
337 40
40
32
337 40
50
32
337 50
40
32
337 50
50
32
337 40
40
32
337 40
50
32
337 50
40
32
337 50
50
32
337 40
40
32
337 40
50
32
337 50
40
32
337 50
50
32
435 50
50
40
435 50
58
40
435 58
50
40
435 58
58
40
435 50
50
40
435 50
58
40
435 58
50
40
435 58
58
40
435 50
50
40
435 50
58
40
435 58
50
40
435 58
58
40
435 50
50
40
435 50
58
40
435 58
50
40
435 58
58
40
515 58
58
40
515 58
63
40
515 63
58
40
515 63
63
40
515 58
58
40
515 58
63
40
515 63
58
40
515 63
63
40
515 58
58
40
515 58
63
40
515 63
58
40
515 63
63
40
E
400
400
400
400
400
400
400
400
400
400
400
400
400
400
400
400
510
510
510
510
510
510
510
510
510
510
510
510
510
510
510
510
590
590
590
590
590
590
590
590
590
590
590
590
E1
150
150
150
150
215
215
215
215
300
300
300
300
400
400
400
400
195
195
195
195
280
280
280
280
380
380
380
380
510
510
510
510
280
280
280
280
380
380
380
380
510
510
510
510
P
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
Pillars
P10.038.xxx B10.038.050
P10.040.xxx B10.040.050
P10.048.xxx B10.048.050
P10.050.xxx B10.050.050
Demountable Pillars and/or Bronze Plated Brushes may be specified and fitted at additional cost.
(Refer to Pillar & Bush Section)
12
Bushes
Standard Die Sets with Four Pillars D84.xxx.xxx
D94.xxx.xxx
C2
C2
P
B
L
C3
E1B1
C1
C1
Standard Die Set with stripper plate
Ref. No.: D84.xxx.xxx
Standard Die Set
Ref. No.: D94.xxx.xxx
P
A1
A
E
External Dimensions
REFERENCE
NUMBER
3 Plate
D84.125.016
D84.225.016
D84.325.016
D84.425.016
D84.125.020
D84.225.020
D84.325.020
D84.425.020
D84.125.025
D84.225.025
D84.325.025
D84.425.025
D84.131.020
D84.231.020
D84.331.020
D84.431.020
D84.131.025
D84.231.025
D84.331.025
D84.431.025
D84.131.031
D84.231.031
D84.331.031
D84.431.031
D84.140.020
D84.240.020
D84.340.020
D84.440.020
D84.140.025
D84.240.025
D84.340.025
D84.440.025
2 Plate
D94.125.016
D94.225.016
D94.325.016
D94.425.016
D94.125.020
D94.225.020
D94.325.020
D94.425.020
D94.125.025
D94.225.025
D94.325.025
D94.425.025
D94.131.020
D94.231.020
D94.331.020
D94.431.020
D94.131.025
D94.231.025
D94.331.025
D94.431.025
D94.131.031
D94.231.031
D94.331.031
D94.431.031
D94.140.020
D94.240.020
D94.340.020
D94.440.020
D94.140.025
D94.240.025
D94.340.025
D94.440.025
STANDARD
ASSEMBLY
Die Space Die Space
A
250
250
250
250
250
250
250
250
250
250
250
250
315
315
315
315
315
315
315
315
315
315
315
315
400
400
400
400
400
400
400
400
B1
37
37
37
37
77
77
77
77
127
127
127
127
77
77
77
77
127
127
127
127
192
192
192
192
77
77
77
77
127
127
127
127
B
160
160
160
160
200
200
200
200
250
250
250
250
200
200
200
200
250
250
250
250
315
315
315
315
200
200
200
200
250
250
250
250
A 1 C1 ± 2 C 2 ± 2 C 3 ± 2
127 32
32
32
127 32
40
32
127 40
32
32
127 40
40
32
127 32
32
32
127 32
40
32
127 40
32
32
127 40
40
32
127 32
32
32
127 32
40
32
127 40
32
32
127 40
40
32
192 32
32
32
192 32
40
32
192 40
32
32
192 40
40
32
192 32
32
32
192 32
40
32
192 40
32
32
192 40
40
32
192 40
40
32
192 40
50
32
192 50
40
32
192 50
50
32
277 40
40
32
277 40
50
32
277 50
40
32
277 50
50
32
277 40
40
32
277 40
50
32
277 50
40
32
277 50
50
32
E
174
174
174
174
174
174
174
174
174
174
174
174
239
239
239
239
239
239
239
239
239
239
239
239
324
324
324
324
324
324
324
324
E1
84
84
84
84
124
124
124
124
174
174
174
174
124
124
124
124
174
174
174
174
239
239
239
239
124
124
124
124
174
174
174
174
P
Pillars
Bushes
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
P10.025.xxx B10.025.050
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
NOTE: Dimension ‘E’ is +2mm on Rear Pillars
13
D84.xxx.xxx
D94.xxx.xxx
Standard Die Sets with Four Pillars
To order specify Die Set Reference No. and Pillar Length (L = see page 24)
Example: D91.350.050 – L=250
External Dimensions
REFERENCE
NUMBER
3 Plate
D84.150.025
D84.250.025
D84.350.025
D84.450.025
D84.150.031
D84.250.031
D84.350.031
D84.450.031
D84.150.040
D84.250.040
D84.350.040
D84.450.040
D84.150.050
D84.250.050
D84.350.050
D84.450.050
D84.163.031
D84.263.031
D84.363.031
D84.463.031
D84.163.040
D84.263.040
D84.363.040
D84.463.040
D84.163.050
D84.263.050
D84.363.050
D84.463.050
D84.163.063
D84.263.063
D84.363.063
D84.463.063
D84.171.040
D84.271.040
D84.371.040
D84.471.040
D84.171.050
D84.271.050
D84.371.050
D84.471.050
D84.171.063
D84.271.063
D84.371.063
D84.471.063
2 Plate
D94.150.025
D94.250.025
D94.350.025
D94.450.025
D94.150.031
D94.250.031
D94.350.031
D94.450.031
D94.150.040
D94.250.040
D94.350.040
D94.450.040
D94.150.050
D94.250.050
D94.350.050
D94.450.050
D94.163.031
D94.263.031
D94.363.031
D94.463.031
D94.163.040
D94.263.040
D94.363.040
D94.463.040
D94.163.050
D94.263.050
D94.363.050
D94.463.050
D94.163.063
D94.263.063
D94.363.063
D94.463.063
D94.171.040
D94.271.040
D94.371.040
D94.471.040
D94.171.050
D94.271.050
D94.371.050
D94.471.050
D94.171.063
D94.271.063
D94.371.063
D94.471.063
STANDARD
ASSEMBLY
Die Space Die Space
A
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
630
630
630
630
630
630
630
630
630
630
630
630
630
630
630
630
710
710
710
710
710
710
710
710
710
710
710
710
B1
106
106
106
106
171
171
171
171
256
256
256
256
356
356
356
356
152
152
152
152
237
237
237
237
337
337
337
337
467
467
467
467
205
205
205
205
305
305
305
305
435
435
435
435
B
250
250
250
250
315
315
315
315
400
400
400
400
500
500
500
500
315
315
315
315
400
400
400
400
500
500
500
500
630
630
630
630
400
400
400
400
500
500
500
500
630
630
630
630
A 1 C1 ± 2 C 2 ± 2 C 3 ± 2
356 40
40
32
356 40
50
32
356 50
40
32
356 50
50
32
356 40
40
32
356 40
50
32
356 50
40
32
356 50
50
32
356 40
40
32
356 40
50
32
356 50
40
32
356 50
50
32
356 40
40
32
356 40
50
32
356 50
40
32
356 50
50
32
467 50
50
40
467 50
58
40
467 58
50
40
467 58
58
40
467 50
50
40
467 50
58
40
467 58
50
40
467 58
58
40
467 50
50
40
467 50
58
40
467 58
50
40
467 58
58
40
467 50
50
40
467 50
58
40
467 58
50
40
467 58
58
40
515 58
58
40
515 58
63
40
515 63
58
40
515 63
63
40
515 58
58
40
515 58
63
40
515 63
58
40
515 63
63
40
515 58
58
40
515 58
63
40
515 63
58
40
515 63
63
40
E
410
410
410
410
410
410
410
410
410
410
410
410
410
410
410
410
530
530
530
530
530
530
530
530
530
530
530
530
530
530
530
530
590
590
590
590
590
590
590
590
590
590
590
590
E1
160
160
160
160
225
225
225
225
310
310
310
310
410
410
410
410
215
215
215
215
300
300
300
300
400
400
400
400
530
530
530
530
280
280
280
280
380
380
380
380
510
510
510
510
P
Pillars
Bushes
45
45
45
45
45
45
45
45
P10.032.xxx B10.032.050
45
45
45
45
45
45
45
45
50
50
50
50
50
50
50
50
P10.040.xxx B10.040.050
50
50
50
50
50
50
50
50
60
60
60
60
60
60
P10.050.xxx B10.050.050
60
60
60
60
60
60
NOTE: Dimension ‘E’ is +2mm on Rear Pillars
Demountable Pillars and/or Bronze Plated Bushes may be specified and fitted at additional cost (Refer to Pillar & Bush Section)
14
Standard Die Sets With Centre Pillars
and Ball Bearing Guide Bushes
C2
D80.xxx.xxx
D90.xxx.xxx
E
C2
P
C3
D
D
D1
D1
B
A1
C1
C1
Standard Die Set with stripper plate
Ref. No.: D80.xxx.xxx
A
Standard Die Set
Ref. No.: D90.xxx.xxx
External Dimensions
REFERENCE
NUMBER
3 Plate
D80.125.016
D80.225.016
D80.325.016
D80.425.016
D80.125.020
D80.225.020
D80.325.020
D80.425.020
D80.125.025
D80.225.025
D80.325.025
D80.425.025
D80.131.020
D80.231.020
D80.331.020
D80.431.020
D80.131.025
D80.231.025
D80.331.025
D80.431.025
D80.131.031
D80.231.031
D80.331.031
D80.431.031
D80.140.020
D80.240.020
D80.340.020
D80.440.020
D80.140.025
D80.240.025
D80.340.025
D80.440.025
D80.140.031
D80.240.031
D80.340.031
D80.440.031
D80.140.040
D80.240.040
D80.340.040
2 Plate
D90.125.016
D90.225.016
D90.325.016
D90.425.016
D90.125.020
D90.225.020
D90.325.020
D90.425.020
D90.125.025
D90.225.025
D90.325.025
D90.425.025
D90.131.020
D90.231.020
D90.331.020
D90.431.020
D90.131.025
D90.231.025
D90.331.025
D90.431.025
D90.131.031
D90.231.031
D90.331.031
D90.431.031
D90.140.020
D90.240.020
D90.340.020
D90.440.020
D90.140.025
D90.240.025
D90.340.025
D90.440.025
D90.140.031
D90.240.031
D90.340.031
D90.440.031
D90.140.040
D90.240.040
D90.340.040
Die Space
A
250
250
250
250
250
250
250
250
250
250
250
250
315
315
315
315
315
315
315
315
315
315
315
315
400
400
400
400
400
400
400
400
400
400
400
400
400
400
400
B
160
160
160
160
200
200
200
200
250
250
250
250
200
200
200
200
250
250
250
250
315
315
315
315
200
200
200
200
250
250
250
250
315
315
315
315
400
400
400
A1
120
120
120
120
120
120
120
120
120
120
120
120
171
171
171
171
171
171
171
171
171
171
171
171
256
256
256
256
256
256
256
256
256
256
256
256
256
256
256
C1 ± 2 C2 ± 2 C3 ± 2
32
32
32
32
40
32
40
32
32
40
40
32
32
32
32
32
40
32
40
32
32
40
40
32
32
32
32
32
40
32
40
32
32
40
40
32
40
40
32
40
50
32
50
40
32
50
50
32
40
40
32
40
50
32
50
40
32
50
50
32
40
40
32
40
50
32
50
40
32
50
50
32
40
40
32
40
50
32
50
40
32
50
50
32
40
40
32
40
50
32
50
40
32
50
50
32
40
40
32
40
50
32
50
40
32
50
50
32
40
40
32
40
50
32
50
40
32
D
25
25
25
25
25
25
25
25
25
25
25
25
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
D1
24
24
24
24
24
24
24
24
24
24
24
24
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
E
165
165
165
165
165
165
165
165
165
165
165
165
225
225
225
225
225
225
225
225
225
225
225
225
310
310
310
310
310
310
310
310
310
310
310
310
310
310
310
P
42
42
42
42
42
42
42
42
42
42
42
42
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
15
D80.xxx.xxx
D90.xxx.xxx
Standard Die Sets With Centre Pillars
and Ball Bearing Guide Bushes
To order specify Die Set Reference No. and details of Pillar, Ball Bearing Guide Bush
and Ball Cage (Refer to Pillar & Bush Section)
Die Space refers to use of B30 Bushes
External Dimensions
REFERENCE
NUMBER
3 Plate
D80.150.025
D80.250.025
D80.350.025
D80.450.025
D80.150.031
D80.250.031
D80.350.031
D80.450.031
D80.150.040
D80.250.040
D80.350.040
D80.450.040
D80.150.050
D80.250.050
D80.350.050
D80.450.050
D80.163.031
D80.263.031
D80.363.031
D80.463.031
D80.163.040
D80.263.040
D80.363.040
D80.463.040
D80.163.050
D80.263.050
D80.363.050
D80.463.050
D80.163.063
D80.263.063
D80.363.063
D80.463.063
D80.171.040
D80.271.040
D80.371.040
D80.471.040
D80.171.050
D80.271.050
D80.371.050
D80.471.050
D80.171.063
D80.271.063
D80.371.063
D80.471.063
Die Space
2 Plate
D90.150.025
D90.250.025
D90.350.025
D90.450.025
D90.150.031
D90.250.031
D90.350.031
D90.450.031
D90.150.040
D90.250.040
D90.350.040
D90.450.040
D90.150.050
D90.250.050
D90.350.050
D90.450.050
D90.163.031
D90.263.031
D90.363.031
D90.463.031
D90.163.040
D90.263.040
D90.363.040
D90.463.040
D90.163.050
D90.263.050
D90.363.050
D90.463.050
D90.163.063
D90.263.063
D90.363.063
D90.463.063
D90.171.040
D90.271.040
D90.371.040
D90.471.040
D90.171.050
D90.271.050
D90.371.050
D90.471.050
D90.171.063
D90.271.063
D90.371.063
D90.471.063
A
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
630
630
630
630
630
630
630
630
630
630
630
630
630
630
630
630
710
710
710
710
710
710
710
710
710
710
710
710
B
250
250
250
250
315
315
315
315
400
400
400
400
500
500
500
500
315
315
315
315
400
400
400
400
500
500
500
500
630
630
630
630
400
400
400
400
500
500
500
500
630
630
630
630
A1
330
330
330
330
330
330
330
330
330
330
330
330
330
330
330
330
429
429
429
429
429
429
429
429
429
429
429
429
429
429
429
429
509
509
509
509
509
509
509
509
509
509
509
509
C1 ± 2 C2 ± 2 C3 ± 2
40
40
32
40
50
32
50
40
32
50
50
32
40
40
32
40
50
32
50
40
32
50
50
32
40
40
32
40
50
32
50
40
32
50
50
32
40
40
32
40
50
32
50
40
32
50
50
32
50
50
40
50
58
40
58
50
40
58
58
40
50
50
40
50
58
40
58
50
40
58
58
40
50
50
40
50
58
40
58
50
40
58
58
40
50
50
40
50
58
40
58
50
40
58
58
40
58
58
40
58
63
40
63
58
40
63
63
40
58
58
40
58
63
40
63
58
40
63
63
40
58
58
40
58
63
40
63
58
40
63
63
40
D
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
Die Space refers to use of B30 Bushes, the use of B40 Bushes will reduce Die Space
16
D1
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
E
395
395
395
395
395
395
395
395
395
395
395
395
395
395
395
395
510
510
510
510
510
510
510
510
510
510
510
510
510
510
510
510
590
590
590
590
590
590
590
590
590
590
590
590
P
52
52
52
52
52
52
52
52
52
52
52
52
52
52
52
52
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
Standard Die Sets With Rear Pillars
and Ball Bearing Guide Bushes
P
C2
D97.xxx.xxx
E
P
D
B
B1
C1
A
Standard Die Set
Ref. No.: D97.xxx.xxx
External Dimensions
REFERENCE
NUMBER
D97.125.016
D97.225.016
D97.325.016
D97.425.016
D97.125.020
D97.225.020
D97.325.020
D97.425.020
D97.125.025
D97.225.025
D97.325.025
D97.425.025
D97.131.020
D97.231.020
D97.331.020
D97.431.020
D97.131.025
D97.231.025
D97.331.025
D97.431.025
D97.131.031
D97.231.031
D97.331.031
D97.431.031
D97.140.020
D97.240.020
D97.340.020
D97.440.020
D97.140.025
D97.240.025
D97.340.025
D97.440.025
D97.140.031
D97.240.031
D97.340.031
D97.440.031
D97.140.040
D97.240.040
D97.340.040
Die Space
B
160
160
160
160
200
200
200
200
250
250
250
250
200
200
200
200
250
250
250
250
315
315
315
315
200
200
200
200
250
250
250
250
315
315
315
315
400
400
400
A
250
250
250
250
250
250
250
250
250
250
250
250
315
315
315
315
315
315
315
315
315
315
315
315
400
400
400
400
400
400
400
400
400
400
400
400
400
400
400
B1
93
93
93
93
133
133
133
133
183
183
183
183
128
128
128
128
178
178
178
178
243
243
243
243
128
128
128
128
178
178
178
178
230
230
230
230
315
315
315
C1 ± 2 C2 ± 2
32
32
32
40
40
32
40
40
32
32
32
40
40
32
40
40
32
32
32
40
40
32
40
40
32
32
32
40
40
32
40
40
32
32
32
40
40
32
40
40
40
40
40
50
50
40
50
50
40
40
40
50
50
40
50
50
40
40
40
50
50
40
50
50
40
40
40
50
50
40
50
50
40
40
40
50
50
40
D1
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
40
40
40
40
40
40
40
E
170
170
170
170
170
170
170
170
170
170
170
170
225
225
225
225
225
225
225
225
225
225
225
225
310
310
310
310
310
310
310
310
295
295
295
295
295
295
295
P
40
40
40
40
40
40
40
40
40
40
40
40
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
52
52
52
52
52
52
52
17
D97.xxx.xxx
Standard Die Sets With Rear Pillars
and Ball Bearing Guide Bushes
To order specify Die Set Reference No. and details of Pillar, Ball Bearing Guide Bush and
Ball Cage (Refer to Pillar & Bush Section)
Die Space refers to use of B30 Bushes
External Dimensions
REFERENCE
NUMBER
D97.150.025
D97.250.025
D97.350.025
D97.450.025
D97.150.031
D97.250.031
D97.350.031
D97.450.031
D97.150.040
D97.250.040
D97.350.040
D97.450.040
D97.150.050
D97.250.050
D97.350.050
D97.450.050
D97.163.031
D97.263.031
D97.363.031
D97.463.031
D97.163.040
D97.263.040
D97.363.040
D97.463.040
D97.163.050
D97.263.050
D97.363.050
D97.463.050
D97.163.063
D97.263.063
D97.363.063
D97.463.063
D97.171.040
D97.271.040
D97.371.040
D97.471.040
D97.171.050
D97.271.050
D97.371.050
D97.471.050
D97.171.063
D97.271.063
D97.371.063
D97.471.063
Die Space
B
250
250
250
250
315
315
315
315
400
400
400
400
500
500
500
500
315
315
315
315
400
400
400
400
500
500
500
500
630
630
630
630
400
400
400
400
500
500
500
500
630
630
630
630
A
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
630
630
630
630
630
630
630
630
630
630
630
630
630
630
630
630
710
710
710
710
710
710
710
710
710
710
710
710
B1
157
157
157
157
222
222
222
222
307
307
307
307
407
407
407
407
206
206
206
206
291
291
291
291
391
391
391
391
521
521
521
521
291
291
291
291
391
391
391
391
521
521
521
521
C1 ± 2 C2 ± 2
40
40
40
50
50
40
50
50
40
40
40
50
50
40
50
50
40
40
40
50
50
40
50
50
40
40
40
50
50
40
50
50
50
50
50
58
58
50
58
58
50
50
50
58
58
50
58
58
50
50
50
58
58
50
58
58
50
50
50
58
58
50
58
58
58
58
58
63
63
58
63
63
58
58
58
63
63
58
63
63
58
58
58
63
63
58
63
63
D1
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
E
395
395
395
395
395
395
395
395
395
395
395
395
395
395
395
395
510
510
510
510
510
510
510
510
510
510
510
510
510
510
510
510
590
590
590
590
590
590
590
590
590
590
590
590
Die Space refers to use of B30 Bushes, the use of B40 Bushes will reduce Die Space
18
P
52
52
52
52
52
52
52
52
52
52
52
52
52
52
52
52
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
Standard Die Sets with Diagonal Pillars
and Ball Bearing Guide Bushes
C2
E
C2
C3
D
D
D1
B
D1
E1
P
P
A1
C1
C1
Standard Die Set with stripper plate
Ref. No.: D85.xxx.xxx
D85.xxx.xxx
D95.xxx.xxx
B1
A
Standard Die Set
Ref. No.: D95.xxx.xxx
External Dimensions
REFERENCE
NUMBER
3 Plate
D85.125.016
D85.225.016
D85.325.016
D85.425.016
D85.125.020
D85.225.020
D85.325.020
D85.425.020
D85.125.025
D85.225.025
D85.325.025
D85.425.025
D85.131.020
D85.231.020
D85.331.020
D85.431.020
D85.131.025
D85.231.025
D85.331.025
D85.431.025
D85.131.031
D85.231.031
D85.331.031
D85.431.031
D85.140.020
D85.240.020
D85.340.020
D85.440.020
D85.140.025
D85.240.025
D85.340.025
D85.440.025
D85.140.031
D85.240.031
D85.340.031
D85.440.031
D85.140.040
D85.240.040
D85.340.040
2 Plate
D95.125.016
D95.225.016
D95.325.016
D95.425.016
D95.125.020
D95.225.020
D95.325.020
D95.425.020
D95.125.025
D95.225.025
D95.325.025
D95.425.025
D95.131.020
D95.231.020
D95.331.020
D95.431.020
D95.131.025
D95.231.025
D95.331.025
D95.431.025
D95.131.031
D95.231.031
D95.331.031
D95.431.031
D95.140.020
D95.240.020
D95.340.020
D95.440.020
D95.140.025
D95.240.025
D95.340.025
D95.440.025
D95.140.031
D95.240.031
D95.340.031
D95.440.031
D95.140.040
D95.240.040
D95.340.040
Die Space
Die Space
A
250
250
250
250
250
250
250
250
250
250
250
250
315
315
315
315
315
315
315
315
315
315
315
315
400
400
400
400
400
400
400
400
400
400
400
400
400
400
400
B
160
160
160
160
200
200
200
200
250
250
250
250
200
200
200
200
250
250
250
250
315
315
315
315
200
200
200
200
250
250
250
250
315
315
315
315
400
400
400
B1
30
30
30
30
70
70
70
70
120
120
120
120
56
56
56
56
106
106
106
106
171
171
171
171
56
56
56
56
106
106
106
106
171
171
171
171
256
256
256
A 1 C1 ± 2
120 32
120 32
120 40
120 40
120 32
120 32
120 40
120 40
120 32
120 32
120 40
120 40
171 32
171 32
171 40
171 40
171 32
171 32
171 40
171 40
171 40
171 40
171 50
171 50
256 40
256 40
256 50
256 50
256 40
256 40
256 50
256 50
256 40
256 40
256 50
256 50
256 40
256 40
256 50
C2 ± 2
32
40
32
40
32
40
32
40
32
40
32
40
32
40
32
40
32
40
32
40
40
50
40
50
40
50
40
50
40
50
40
50
40
50
40
50
40
50
40
C3 ± 2
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
D
25
25
25
25
25
25
25
25
25
25
25
25
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
D1
24
24
24
24
24
24
24
24
24
24
24
24
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
E
165
165
165
165
165
165
165
165
165
165
165
165
225
225
225
225
225
225
225
225
225
225
225
225
310
310
310
310
310
310
310
310
310
310
310
310
310
310
310
E1
75
75
75
75
115
115
115
115
165
165
165
165
110
110
110
110
160
160
160
160
225
225
225
225
110
110
110
110
160
160
160
160
225
225
225
225
310
310
310
P
42
42
42
42
42
42
42
42
42
42
42
42
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
19
D85.xxx.xxx
D95.xxx.xxx
Standard Die Sets with Diagonal Pillars
and Ball Bearing Guide Bushes
To order specify Die Set Reference No. and details of Pillar, Ball Bearing Guide Bush and Ball Cage
(Refer to Pillar & Bush Section)
Die Space refers to use of B30 Bushes
External Dimensions
REFERENCE
NUMBER
3 Plate
D85.150.025
D85.250.025
D85.350.025
D85.450.025
D85.150.031
D85.250.031
D85.350.031
D85.450.031
D85.150.040
D85.250.040
D85.350.040
D85.450.040
D85.150.050
D85.250.050
D85.350.050
D85.450.050
D85.163.031
D85.263.031
D85.363.031
D85.463.031
D85.163.040
D85.263.040
D85.363.040
D85.463.040
D85.163.050
D85.263.050
D85.363.050
D85.463.050
D85.163.063
D85.263.063
D85.363.063
D85.463.063
D85.171.040
D85.271.040
D85.371.040
D85.471.040
D85.171.050
D85.271.050
D85.371.050
D85.471.050
D85.171.063
D85.271.063
D85.371.063
D85.471.063
2 Plate
D95.150.025
D95.250.025
D95.350.025
D95.450.025
D95.150.031
D95.250.031
D95.350.031
D95.450.031
D95.150.040
D95.250.040
D95.350.040
D95.450.040
D95.150.050
D95.250.050
D95.350.050
D95.450.050
D95.163.031
D95.263.031
D95.363.031
D95.463.031
D95.163.040
D95.263.040
D95.363.040
D95.463.040
D95.163.050
D95.263.050
D95.363.050
D95.463.050
D95.163.063
D95.263.063
D95.363.063
D95.463.063
D95.171.040
D95.271.040
D95.371.040
D95.471.040
D95.171.050
D95.271.050
D95.371.050
D95.471.050
D95.171.063
D95.271.063
D95.371.063
D95.471.063
Die Space
Die Space
A
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
630
630
630
630
630
630
630
630
630
630
630
630
630
630
630
630
710
710
710
710
710
710
710
710
710
710
710
710
B
250
250
250
250
315
315
315
315
400
400
400
400
500
500
500
500
315
315
315
315
400
400
400
400
500
500
500
500
630
630
630
630
400
400
400
400
500
500
500
500
630
630
630
630
B1
80
80
80
80
145
145
145
145
230
230
230
230
330
330
330
330
114
114
114
114
199
199
199
199
299
299
299
299
429
429
429
429
199
199
199
199
299
299
299
299
429
429
429
429
A 1 C1 ± 2
330 40
330 40
330 50
330 50
330 40
330 40
330 50
330 50
330 40
330 40
330 50
330 50
330 40
330 40
330 50
330 50
429 50
429 50
429 58
429 58
429 50
429 50
429 58
429 58
429 50
429 50
429 58
429 58
429 50
429 50
429 58
429 58
509 58
509 58
509 63
509 63
509 58
509 58
509 63
509 63
509 58
509 58
509 63
509 63
C2 ± 2
40
50
40
50
40
50
40
50
40
50
40
50
40
50
40
50
50
58
50
58
50
58
50
58
50
58
50
58
50
58
50
58
58
63
58
63
58
63
58
63
58
63
58
63
C3 ± 2
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
D
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
D1
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
38
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
Die Space refers to use of B30 Bushes, the use of B40 Bushes will reduce Die Space
20
E
395
395
395
395
395
395
395
395
395
395
395
395
395
395
395
395
510
510
510
510
510
510
510
510
510
510
510
510
510
510
510
510
590
590
590
590
590
590
590
590
590
590
590
590
E1
145
145
145
145
210
210
210
210
295
295
295
295
395
395
395
395
195
195
195
195
280
280
280
280
380
380
380
380
510
510
510
510
280
280
280
280
380
380
380
380
510
510
510
510
P
52
52
52
52
52
52
52
52
52
52
52
52
52
52
52
52
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
Standard Die Sets with Four Pillars
and Ball Bearing Guide Bushes
C2
C2
P
C3
D
B
D
C1
E1
B1
C1
Standard Die Set with stripper plate
Ref. No.: D89.xxx.xxx
D89.xxx.xxx
D99.xxx.xxx
Standard Die Set
Ref. No.: D99.xxx.xxx
P
A
A1
E
External Dimensions
REFERENCE
NUMBER
3 Plate
D89.125.016
D89.225.016
D89.325.016
D89.425.016
D89.125.020
D89.225.020
D89.325.020
D89.425.020
D89.125.025
D89.225.025
D89.325.025
D89.425.025
D89.131.020
D89.231.020
D89.331.020
D89.431.020
D89.131.025
D89.231.025
D89.331.025
D89.431.025
D89.131.031
D89.231.031
D89.331.031
D89.431.031
D89.140.020
D89.240.020
D89.340.020
D89.440.020
D89.140.025
D89.240.025
D89.340.025
D89.440.025
D89.140.031
D89.240.031
D89.340.031
D89.440.031
D89.140.040
D89.240.040
D89.340.040
2 Plate
D99.125.016
D99.225.016
D99.325.016
D99.425.016
D99.125.020
D99.225.020
D99.325.020
D99.425.020
D99.125.025
D99.225.025
D99.325.025
D99.425.025
D99.131.020
D99.231.020
D99.331.020
D99.431.020
D99.131.025
D99.231.025
D99.331.025
D99.431.025
D99.131.031
D99.231.031
D99.331.031
D99.431.031
D99.140.020
D99.240.020
D99.340.020
D99.440.020
D99.140.025
D99.240.025
D99.340.025
D99.440.025
D99.140.031
D99.240.031
D99.340.031
D99.440.031
D99.140.040
D99.240.040
D99.340.040
Die Space
Die Space
A
250
250
250
250
250
250
250
250
250
250
250
250
315
315
315
315
315
315
315
315
315
315
315
315
400
400
400
400
400
400
400
400
400
400
400
400
400
400
400
B
160
160
160
160
200
200
200
200
250
250
250
250
200
200
200
200
250
250
250
250
315
315
315
315
200
200
200
200
250
250
250
250
315
315
315
315
400
400
400
B1
30
30
30
30
70
70
70
70
120
120
120
120
70
70
70
70
120
120
120
120
185
185
185
185
70
70
70
70
120
120
120
120
165
165
165
165
250
250
250
A 1 C1 ± 2
120 32
120 32
120 40
120 40
120 32
120 32
120 40
120 40
120 32
120 32
120 40
120 40
185 32
185 32
185 40
185 40
185 32
185 32
185 40
185 40
185 40
185 40
185 50
185 50
270 40
270 40
270 50
270 50
270 40
270 40
270 50
270 50
250 40
250 40
250 50
250 50
250 40
250 40
250 50
C2 ± 2
32
40
32
40
32
40
32
40
32
40
32
40
32
40
32
40
32
40
32
40
40
50
40
50
40
50
40
50
40
50
40
50
40
50
40
50
40
50
40
C3 ± 2
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
D
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
32
32
32
32
32
32
32
D1
165
165
165
165
165
165
165
165
165
165
165
165
230
230
230
230
230
230
230
230
230
230
230
230
315
315
315
315
315
315
315
315
304
304
304
304
304
304
304
E
75
75
75
75
115
115
115
115
165
165
165
165
115
115
115
115
165
165
165
165
230
230
230
230
115
115
115
115
165
165
165
165
219
219
219
219
304
304
304
E1
42
42
42
42
42
42
42
42
42
42
42
42
42
42
42
42
42
42
42
42
42
42
42
42
42
42
42
42
42
42
42
42
48
48
48
48
48
48
48
P
52
52
52
52
52
52
52
52
52
52
52
52
52
52
52
52
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
NOTE: Dimension ‘E’ is +2mm on Rear Pillars
21
D89.xxx.xxx
D99.xxx.xxx
Standard Die Sets with Four Pillars
and Ball Bearing Guide Bushes
To order specify Die Set Reference No. and details of Pillar, Ball Bearing Guide Bush and
Ball Cage (Refer to Pillar and Bush Section)
Die Space refers to use of B30 Bushes
External Dimensions
REFERENCE
NUMBER
3 Plate
D89.150.025
D89.250.025
D89.350.025
D89.450.025
D89.150.031
D89.250.031
D89.350.031
D89.450.031
D89.150.040
D89.250.040
D89.350.040
D89.450.040
D89.150.050
D89.250.050
D89.350.050
D89.450.050
D89.163.031
D89.263.031
D89.363.031
D89.463.031
D89.163.040
D89.263.040
D89.363.040
D89.463.040
D89.163.050
D89.263.050
D89.363.050
D89.463.050
D89.163.063
D89.263.063
D89.363.063
D89.463.063
D89.171.040
D89.271.040
D89.371.040
D89.471.040
D89.171.050
D89.271.050
D89.371.050
D89.471.050
D89.171.063
D89.271.063
D89.371.063
2 Plate
D99.150.025
D99.250.025
D99.350.025
D99.450.025
D99.150.031
D99.250.031
D99.350.031
D99.450.031
D99.150.040
D99.250.040
D99.350.040
D99.450.040
D99.150.050
D99.250.050
D99.350.050
D99.450.050
D99.163.031
D99.263.031
D99.363.031
D99.463.031
D99.163.040
D99.263.040
D99.363.040
D99.463.040
D99.163.050
D99.263.050
D99.363.050
D99.463.050
D99.163.063
D99.263.063
D99.363.063
D99.463.063
D99.171.040
D99.271.040
D99.371.040
D99.471.040
D99.171.050
D99.271.050
D99.371.050
D99.471.050
D99.171.063
D99.271.063
D99.371.063
Die Space
Die Space
A
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
630
630
630
630
630
630
630
630
630
630
630
630
630
630
630
630
710
710
710
710
710
710
710
710
710
710
710
B
250
250
250
250
315
315
315
315
400
400
400
400
500
500
500
500
315
315
315
315
400
400
400
400
500
500
500
500
630
630
630
630
400
400
400
400
500
500
500
500
630
630
630
B1
100
100
100
100
165
165
165
165
250
250
250
250
350
350
350
350
140
140
140
140
225
225
225
225
325
325
325
325
455
455
455
455
190
190
190
190
290
290
290
290
420
420
420
A1 C1 ± 2 C2 ± 2 C3 ± 2
350
40
40
32
350
40
50
32
350
50
40
32
350
50
50
32
350
40
40
32
350
40
50
32
350
50
40
32
350
50
50
32
350
40
40
32
350
40
50
32
350
50
40
32
350
50
50
32
350
40
40
32
350
40
50
32
350
50
40
32
350
50
50
32
455
50
50
40
455
50
58
40
455
58
50
40
455
58
58
40
455
50
50
40
455
50
58
40
455
58
50
40
455
58
58
40
455
50
50
40
455
50
58
40
455
58
50
40
455
58
58
40
455
50
50
40
455
50
58
40
455
58
50
40
455
58
58
40
500
58
58
40
500
58
63
40
500
63
58
40
500
63
63
40
500
58
58
40
500
58
63
40
500
63
58
40
500
63
63
40
500
58
58
40
500
58
63
40
500
63
58
40
D
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
50
50
50
50
50
50
50
50
50
50
50
NOTE: Dimension ‘E’ is +2mm on Rear Pillars
Die Space refers to use of B30 Bushes, the use of B40 Bushes will reduce Die Space
22
E
404
404
404
404
404
404
404
404
404
404
404
404
404
404
404
404
520
520
520
520
520
520
520
520
520
520
520
520
520
520
520
520
581
581
581
581
581
581
581
581
581
581
581
E1
154
154
154
154
219
219
219
219
304
304
304
304
404
404
404
404
205
205
205
205
290
290
290
290
390
390
390
390
520
520
520
520
271
271
271
271
371
371
371
371
501
501
501
P
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
64
64
64
64
64
64
64
64
64
64
64
Standard Shanks & Setting Posts
D Length
C Length
AØ
Symbol No.
A
SSM25
25
SSM32
32
SSM40
B
BØ
C
D
Symbol No.
A
B
C
1”
3
M20 x 2.5
45
35
SSI10
M20 x 2.5
56
35
SSI15
40
M20 x 3
70
45
SSI20
/4” WHIT
2”
2”
11/2”
3
/4” WHIT
2”
11/2”
2”
11/4” WHIT
2”
2”
SSI25
1
SSM50
50
M20 x 3
80
60
SSM65
65
M20 x 3
90
60
2 /2”
1 /4” WHIT
2”
2”
SSI30
3”
11/4” WHIT
3”
2”
1
D
Example order: 2 off SSM25
B +0.5
C
A
E
D
Symbol No.
A
B
C
D
E
SP20
20
22.0–80.0
11
13
7
SP25
25
22.0–90.0
14
15
9
SP32
32
22.0–100.0
14
15
9
SP38
38
25.0–100.0
17
18
11
SP50
50
25.0–100.0
17
18
11
Example order: 6 off SP25 x 55.0
Will be supplied soft unless otherwise stated.
23
Special Die Sets
In addition to the AW Precision range of Standard Die Sets we are able to
offer an excellent service to manufacture and supply SPECIAL DIE SETS
to individual design requirements.
With the benefit of the latest generation CNC machine technology we can
supply die sets with peripheral shapes flamecut to your particular design
specifications, together with flamecut apertures.
Alternatively, we can supply with machined apertures and pockets, etc.
All die set plates are stress relieved prior to grinding and machining.
Please forward your design specification for quotation.
24
Guide Pillars P10.xxx.xxx
Example
To use with
d
Bush B10.xxx.xxx
B12.xxx.xxx
page 28
min 1.5 x d
m
Case Hardened 60 – 64 HRc
L
Bush B30.xxx.xxx
Ball Cage C11.xxx.xxx
C12.xxx.xxx
pages 30 & 33
D1
Demountable Bush B40.xxx.xxx
Ball Cage C11.xxx.xxx
C12.xxx.xxx
pages 32 & 33
D1
d
m
L
100
110
125
140
160
180
200
220
250
280
315
355
400
450
500
19
M5
6
20
24
M6
8
25
30
M8
8
32
38
M10
8
40
48
M12
8
50
63
M16
8
80
M20
8
CATALOGUE REFERENCES
P10.019.100 P10.020.100 P10.024.100 P10.025.100
P10.019.110 P10.020.110 P10.024.110 P10.025.110 P10.030.110 P10.032.110
P10.019.125 P10.020.125 P10.024.125 P10.025.125 P10.030.125 P10.032.125 P10.038.125 P10.040.125
P10.019.140 P10.020.140 P10.024.140 P10.025.140 P10.030.140 P10.032.140 P10.038.140 P10.040.140
P10.019.160 P10.020.160 P10.024.160 P10.025.160 P10.030.160 P10.032.160 P10.038.160 P10.040.160 P10.048.160 P10.050.160
P10.019.180 P10.020.180 P10.024.180 P10.025.180 P10.030.180 P10.032.180 P10.038.180 P10.040.180 P10.048.180 P10.050.180
P10.019.200 P10.020.200 P10.024.200 P10.025.200 P10.030.200 P10.032.200 P10.038.200 P10.040.200 P10.048.200 P10.050.200 P10.063.200
P10.024.220 P10.025.220 P10.030.220 P10.032.220 P10.038.220 P10.040.220 P10.048.220 P10.050.220 P10.063.220
P10.024.250 P10.025.250 P10.030.250 P10.032.250 P10.038.250 P10.040.250 P10.048.250 P10.050.250 P10.063.250
P10.024.280 P10.025.280 P10.030.280 P10.032.280 P10.038.280 P10.040.280 P10.048.280 P10.050.280 P10.063.280 P10.080.280
P10.030.315 P10.032.315 P10.038.315 P10.040.315 P10.048.315 P10.050.315 P10.063.315 P10.080.315
P10.038.355 P10.040.355 P10.048.355 P10.050.355 P10.063.355 P10.080.355
P10.048.400 P10.050.400 P10.063.400 P10.080.400
P10.048.450 P10.050.450 P10.063.450 P10.080.450
P10.080.500
Example order (give pillar diameter and length) P10.020.140
25
Standard Die Set Demountable Guide Bushes
D4
D2
E
h
T
L
F
D1
D3
- Case Hardened 60 - 64 HRC
- supplied with clamps and screws
BUSH - Standard
Position of fixing clamps
N
M
M
N
120°
30°
30°
M
120°
N
for 19 & 20mm diam.
for 24 to 40mm diam.
for 48 & 50mm diam.
BUSH STANDARD
D1
F
L
Ref. Bush
Bronze
D2
D3
D4
E
h
No
Ref. clamps
Screw
M
N
T
26
19
20
32
50
B10.0xx.032
B20.0xx.032
28
29
32.5
18
3.2
2
B01.005.000
M5 x 12
19.5
25.5
10.5
24
25
50
72
B10.0xx.050
B20.0xx.050
38
42
47
22
5
3
B01.006.000
M6 x 16
27.5
35
14.7
30
32
50
75
B10.0xx.050
B20.0xx.050
45
49
54
25
5
3
B01.006.000
M6 x 16
31
38.2
14.7
38
40
50
80
B10.0xx.050
B20.0xx.050
54
58
63
30
5
4
B01.008.000
M8 x 20
37
46.3
17.5
48
50
50
85
B10.0xx.050
B20.0xx.050
65
70
75
35
5
4
B01.008.000
M8 x 20
43
52.3
17.5
Demountable Guide Pillars P21.xxx.xxx
with fixing clamps
D1
To use with
m
Bush B10.xxx.xxx
B12.xxx.xxx
page 28
d
F
Bush B30.xxx.xxx
Ball Cage C11.xxx.xxx
C12.xxx.xxx
pages 30 & 33
- Case Hardened 60 – 64 HRc
- Supplied with end cap and screws
T
D2
d
E
D3
Q1
N Q1
M
Q2
Demountable Bush B40.xxx.xxx
Ball Cage C11.xxx.xxx
C12.xxx.xxx
for diameter 19 to 32
pages 32 & 33
D1 = D2
D3
E
d
m
Qty
Réf
Vis
M
N
Q1
Q2
T
F
80
90
100
110
125
140
160
180
200
220
250
280
315
355
400
19
25
20
M5
6
3
20
24
32
25
M6
8
3
25
30
40
32
M6
8
3
32
38
50
40
M10
8
4
40
M
N
Q2
for diameter 38 to 80
48
63
45
M12
8
4
50
63
76
50
M16
8
4
80
93
60
M20
8
4
B01.005.000
B01.006.000
B01.006.000
B01.008.000
B01.008.000
B01.008.000 B01.008.000
M5 x 12
16
22
16.5
22.2
10.5
M6 x 16
20.3
27.5
20.6
27.8
14.7
M6 x 16
24
31.5
22.6
31.3
14.7
M8 x 20
30
39.3
26.5
38
17.5
M8 x 20
36.5
45.8
38
38
17.5
M8 x 20 M8 x 20
42.5
51
51.8
60.3
42.2
48.3
42.2
48.3
17.5
17.5
CATALOGUE REFERENCES
P21.019.080
P21.019.090
P21.019.100
P21.019.110
P21.019.125
P21.019.140
P21.019.160
P21.020.080
P21.020.090
P21.020.100
P21.020.110
P21.020.125
P21.020.140
P21.020.160
P21.024.080
P21.024.090
P21.024.100
P21.024.110
P21.024.125
P21.024.140
P21.024.160
P21.024.180
P21.024.200
P21.025.080
P21.025.090
P21.025.100
P21.025.110
P21.025.125
P21.025.140
P21.025.160
P21.025.180
P21.025.200
P21.030.100
P21.030.110
P21.030.125
P21.030.140
P21.030.160
P21.030.180
P21.030.200
P21.030.220
P21.030.250
P21.030.280
P21.032.100
P21.032.110
P21.032.125
P21.032.140
P21.032.160
P21.032.180
P21.032.200
P21.032.220
P21.032.250
P21.032.280
P21.038.100
P21.038.110
P21.038.125
P21.038.140
P21.038.160
P21.038.180
P21.038.200
P21.038.220
P21.038.250
P21.038.280
P21.040.100
P21.040.110
P21.040.125
P21.040.140
P21.040.160
P21.040.180
P21.040.200
P21.040.220
P21.040.250
P21.040.280
P21.048.110
P21.048.125
P21.048.140
P21.048.160
P21.048.180
P21.048.200
P21.048.220
P21.048.250
P21.048.280
P21.048.315
P21.048.355
P21.048.400
P21.050.110
P21.050.125
P21.050.140
P21.050.160
P21.050.180
P21.050.200
P21.050.220
P21.050.250
P21.050.280
P21.050.315
P21.050.355
P21.050.400
P21.063.125
P21.063.140
P21.063.160
P21.063.180
P21.063.200
P21.063.220
P21.063.250
P21.063.280
P21.063.315
P21.063.355
P21.063.400
P21.080.200
P21.080.220
P21.080.250
P21.080.280
P21.080.315
P21.080.355
P21.080.400
Example order (give pillar diameter and length) P21.020.140
27
P22.xxx.xxx
Demountable Guide Pillars
with central fixing
Example
To use with
Bush B10.xxx.xxx
B12.xxx.xxx
page 28
D1
m
d
F
Bush B30.xxx.xxx
Ball Cage C11.xxx.xxx
C12.xxx.xxx
pages 30 & 33
- Case Hardened 60 – 64 HRc
- Supplied with end cap and screws
D3
h
D2
E
d
Demountable Bush B40.xxx.xxx
Ball Cage C11.xxx.xxx
C12.xxx.xxx
pages 32 & 33
D1 = D2
D3
D4
D5
E
d
m
a
b
Cmin
h
F
80
90
100
110
125
140
160
180
200
220
250
280
315
355
400
19
25
25
19
20
M5
6
3.3
4.2
28
20
24
32
32
24
25
M6
8
5
4
35
25
P02.020.000
P02.025.000
3.3
5
P22.019.080
P22.019.090
P22.019.100
P22.019.110
P22.019.125
P22.019.140
P22.019.160
P22.020.080
P22.020.090
P22.020.100
P22.020.110
P22.020.125
P22.020.140
P22.020.160
P22.024.080
P22.024.090
P22.024.100
P22.024.110
P22.024.125
P22.024.140
P22.024.160
P22.024.180
P22.024.200
P22.025.080
P22.025.090
P22.025.100
P22.025.110
P22.025.125
P22.025.140
P22.025.160
P22.025.180
P22.025.200
30
40
40
30
32
M8
8
5
7
45
32
P02.032.000
50
50
38
40
M 10
8
5
10
56
40
P02.040.000
48
63
63
48
45
M 12
8
5
13
64
P22.032.100
P22.032.110
P22.032.125
P22.032.140
P22.032.160
P22.032.180
P22.032.200
P22.032.220
P22.032.250
P22.032.280
P22.038.100
P22.038.110
P22.038.125
P22.038.140
P22.038.160
P22.038.180
P22.038.200
P22.038.220
P22.038.250
P22.038.280
P22.040.100
P22.040.110
P22.040.125
P22.040.140
P22.040.160
P22.040.180
P22.040.200
P22.040.220
P22.040.250
P22.040.280
5
P22.048.110
P22.048.125
P22.048.140
P22.048.160
P22.048.180
P22.048.200
P22.048.220
P22.048.250
P22.048.280
P22.048.315
P22.048.355
P22.048.400
Example order (give pillar diameter and length) P22.020.140
28
50
P02.050.000
5
5
CATALOGUE REFERENCES
P22.030.100
P22.030.110
P22.030.125
P22.030.140
P22.030.160
P22.030.180
P22.030.200
P22.030.220
P22.030.250
P22.030.280
b
a
D5
D4
38
P22.050.110
P22.050.125
P22.050.140
P22.050.160
P22.050.180
P22.050.200
P22.050.220
P22.050.250
P22.050.280
P22.050.315
P22.050.355
P22.050.400
C min
63
76
76
63
50
M 16
8
5
19
75
80
93
93
80
60
M 20
8
5
25
91
P02.063.000 P02.080.000
5
5
P22.063.125
P22.063.140
P22.063.160
P22.063.180
P22.063.200
P22.063.220
P22.063.250
P22.063.280
P22.063.315
P22.063.355
P22.063.400
P22.080.200
P22.080.220
P22.080.250
P22.080.280
P22.080.315
P22.080.355
P22.080.400
B12.xxx.xxx
Demountable Guide Bushes B10.xxx.xxx
B20.xxx.xxx
Plain and Bronze lined
B22.xxx.xxx
D4
D2
To use with
BUSH EXTRA LONG
PlainB10.XXX.100
Bronze Lined B20.XXX.100
E
h
T
L
F
Pillar P10 .xxx.xxx
Page 24
D1
D3
- Case Hardened 60 – 64 HRc
- Supplied with clamps and screws
D4
D2
Demountable pillar
?P21.xxx.xxx page 26
E
BUSH LONG
h
PlainB10.XXX.075
T
Bronze Lined B20.XXX.075
L
F
D1
D3
Demountable pillar
?P22.xxx.xx page 27
D4
D2
BUSH STANDARD
PlainB10.XXX.032
B10.XXX.050
Bronze Lined B20.XXX.032
B20.XXX.050
E
L
h
T
F
D1
D3
Position of fixing clamps
MN
for dia. 19 & 20
D4
D2
BUSH SHORT
N
M
PlainB10.XXX.016
B10.XXX.020
Bronze Lined B20.XXX.016
B20.XXX.020
Q1
E
T
Q2
D4
D2
BUSH EXTRA SHORT
M
N
for dia. 38 to 80
Q1
L
F
D1
D3
for dia. 24 to 32
Q2
h
PlainB12.XXX.010
B12.XXX.014
Bronze Lined B22.XXX.010
B22.XXX.014
E L
X
h
T
F
D1
D3
29
B10.xxx.xxx
B12.xxx.xxx
B20.xxx.xxx
B22.xxx.xxx
Demountable Guide Bushes
Plain and Bronze lined
D1
D2
D3
D4
E
h
Qty
Clamps
Screw
M
N
Q1
Q2
T
19
28
29
32.5
18
3.2
2
20
24
38
42
47
22
5
3
25
38
54
58
63
30
5
4
40
48
65
70
75
35
5
4
50
63
81
88
93
48
5
4
80
100
110
115
48
5
4
B01.006.000
B01.006.000
B01.008.000
B01.008.000
B01.008.000
B01.008.000
M6 x 16
27.5
35
24.2
34
14.7
M6 x 16
31
38.2
26
37
14.7
M8 x 20
37
46.3
31.5
44.1
17.5
M8 x 20
43
52.3
37.5
52.3
17.5
M8 x 20
53
61.3
46.5
57
17.5
M8 x 20
63
72.3
57.5
66.6
17.5
BUSH EXTRA-LONG
30
32
38
40
100
100
125
130
B10.0xx.100 B10.0xx.100
B20.0xx.100 B20.0xx.100
24
25
24
25
24
25
75
97
B10.0xx.075
B20.0xx.075
19
20
19
20
32
50
B10.0xx.032
B20.0xx.032
16
34
B10.0xx.016
B20.0xx.016
D1
19
20
D3
29
F
10
E
18
L
28
X
6
Clamps
B01.005.000
Screws
M5 x 12
M
19.5
N
25.5
Q1
—
Q2
—
Bush Plain
B12.0xx.010
Bush Bronze Plated B22.0xx.010
30
32
M5 x 12
19.5
25.5
—
—
10.5
D1
F
L
Bush Plain
Bush Bronze Plated
D1
F
L
Bush Plain
Bush Bronze Plated
45
49
54
25
5
3
B01.005.000
D1
F
L
Bush Plain
Bush Bronze Plated
D1
F
L
Bush Plain
Bush Bronze Plated
30
50
72
B10.0xx.050
B20.0xx.050
20
42
B10.0xx.020
B20.0xx.020
BUSH LONG
32
38
40
75
75
100
105
B10.0xx.075 B10.0xx.075
B20.0xx.075 B20.0xx.075
30
BUSH STANDARD
30
32
38
40
50
50
75
80
B10.0xx.050 B10.0xx.050
B20.0xx.050 B20.0xx.050
BUSH SHORT
30
32
38
40
20
20
45
50
B10.0xx.020 B10.0xx.020
B20.0xx.020 B20.0xx.020
BUSH EXTRA SHORT
30
32
38
40
36
43
50
10
10
14
23
30
38
33
40
52
6
10
10
B02.006.000 B02.006.000 B02.008.000
M6 x 12
M6 x 12
M8 x 16
30
33.5
40
38
41.5
51.2
25.3
27
33.8
36.6
39.6
49
B12.0xx.010 B12.0xx.010 B12.0xx.014
B22.0xx.010 B22.0xx.010 B22.0xx.014
24
25
48
50
100
135
B10.0xx.100
B20.0xx.100
63
100
148
B10.063.100
B20.063.100
48
63
75
123
B10.063.075
B20.063.075
48
63
50
98
B10.063.050
B20.063.050
80
50
98
B10.080.050
B20.080.050
48
63
20
68
B10.063.020
B20.063.020
80
20
68
B10.080.020
B20.080.020
48
63
79
14
61
75
20
B02.008.000
M8 x 16
55
66.7
46.5
62.5
B12.063.014
B22.063.014
80
99
14
78
92
32
B02.008.000
M8 x 16
66
77.2
57.5
71.6
B12.080.014
B22.080.014
50
75
110
B10.0xx.075
B20.0xx.075
50
50
85
B10.0xx.050
B20.0xx.050
50
20
55
B10.0xx.020
B20.0xx.020
50
64
14
48
62
20
B02.008.000
M8 x 16
46
57.2
37.5
54.2
B12.0xx.014
B22.0xx.014
Straight Sleeve Ball Bearing Bushes B30.xxx.xxx
To use with
Pillar P10 .xxx.xxx
Page 24
L
D1
Alloy steel
Vacuum hardened
Demountable pillar
P21.xxx.xxx page 26
Ball cage
C11.xxx.xxx
C12.xxx.xxx
page 33
D2
Demountable pillar
P22.xxx.xx page 27
D1
D2
L
65
80
95
110
130
150
170
190
215
240
265
24
45
25
30
54
32
38
65
40
48
81
50
63
95
CATALOGUE REFERENCES
B30.025.065
B30.024.080 B30.025.080
B30.032.080 B30.038.080 B30.040.080
B30.025.095
B30.032.095 B30.038.095 B30.040.095
B30.025.110 B30.030.110 B30.032.110 B30.038.110 B30.040.110
B30.024.130 B30.025.130
B30.032.130
B30.050.110
B30.040.130 B30.048.130 B30.050.130
B30.032.150 B30.038.150 B30.040.150
B30.030.170 B30.032.170
B30.040.170
B30.050.150 B30.063.150
B30.050.170 B30.063.170
B30.040.190 B30.048.190 B30.050.190 B30.063.190
B30.038.215 B30.040.215
B30.050.215 B30.063.215
B30.050.240 B30.063.240
B30.048.265 B30.050.265 B30.063.265
Mounting Instructions
Ball bearing guide bushes are mounted and secured in position as follows.
1. Degrease with acetone or similar and wipe carefully.
2. A
pply a thin layer of retaining compound on the two surfaces and position the bush, whilst turning in the bore.
3. Allow to harden for the required time i.e. 4 hours at 22°C.
80mm available on request.
31
C13.xxx.xxx
B42.xxx.xxx
Stripper Plate
Demountable Guide Bushes & Ball Bearing Cages
D1
X
S
L
D1
X
S
24
4.2
1.6
25
4.2
1.6
L
40 C13.024.040
52 C13.024.052
63 C13.024.063
80 C13.024.080
100
125
30
4.9
1.9
BALL CAGE
38
40
5.7
5.7
1.9
1.9
32
4.9
1.9
48
6.7
2.2
50
6.7
2.2
63
6.7
2.2
CATALOGUE REFERENCES
C13.025.040 C13.030.040 C13.032.040
C13.025.052 C13.030.052 C13.032.052 C13.038.052 C13.040.052
C13.025.063 C13.030.063 C13.032.063
C13.048.063 C13.050.063
C13.025.080 C13.030.080 C13.032.080 C13.038.080 C13.040.080 C13.048.080 C13.050.080
C13.048.100 C13.032.100 C13.038.100 C13.040.100 C13.048.100 C13.050.100 C13.063.100
C13.038.125 C13.040.125 C13.048.125 C13.050.125 C13.063.125
D3
D1
10
C
D2
D4
D1
C
40
52
63
80
100
125
D2
D3
D4
Qty
Clamps
Screws
M
N
Q1
Q2
32
BUSHES
24
25
30
B42.024.030
B42.025.030
B42.030.030
B42.032.030
B42.024.035
B42.025.035
B42.030.035
B42.032.035
B42.030.042
B42.032.042
40
48
50
B42.050.046
CATALOGUE REFERENCES
45
43
54
54
50
63
3
B02.006.000
M6 x 12
33.7
41.5
27
39.5
3
B02.006.000
M6 x 12
40
46
29.3
43.4
B42.038.039
B42.040.039
B42.038.046
B42.040.046
B42.048.046
B42.038.054
B42.040.054
B42.048.054
FIXINGS
80mm available on request.
32
38
B42.050.054
65
64
75
81
79
93
4
B02.008.000
M8 x 20
46
52
32.2
48.6
4
B02.008.000
M8 x 20
55
61
36.7
56.4
Demountable Guide Bushes B40.xxx.xxx
for use with Ball Bearing Cages
To use with
D3
Pillar P10 .xxx.xxx
Page 24
F
D1
T
- Case Hardened
60 – 64 HRc
- Supplied with
clamps and screws
Demountable pillar
P21.xxx.xxx page 26
E
Ball cage
C11.xxx.xxx
C12.xxx.xxx
page 33
D2
D4
Demountable pillar
P22.xxx.xx page 27
N
M
Position of
Q1
Q2
N
M
Q2
Q1
D1
F
35
50
65
80
100
120
140
D2
D3
D4
E
D1
Qty
Clamps
Screws
M
N
Q1
Q2
T
24
25
30
32
38
40
48
50
63
CATALOGUE REFERENCES
B40.024.035 B40.025.035
B40.024.050 B40.025.050 B40.030.050 B40.032.050 B40.038.050 B40.040.050
B40.024.065 B40.025.065 B40.030.065 B40.032.065 B40.038.065 B40.040.065 B40.048.065
B40.030.080 B40.032.080 B40.038.080 B40.040.080 B40.048.080
B40.038.100 B40.040.100 B40.048.100
B40.048.120
45
49
54
30
24
3
54
58
63
30
25
B01.006.000
M6 x 16
31
38.2
26
37
14.7
30
3.08
32
B01.006.000
65
70
75
30
FIXINGS
38
40
4
M8 x 20
37
46.3
30
44.1
17.5
B01.008.000
M8 x 20
43
52.3
33
49.3
17.5
B40.050.065
B40.050.080
B40.050.100 B40.063.100
B40.050.120 B40.063.120
B40.063.140
81
88
93
50
48
4
95
103
108
50
50
B01.008.000
M8 x 20
53
61.3
37.5
57
17.5
63
4
B01.008.000
M8 x 20
60
69.3
41.5
64
17.5
80mm available on request.
33
C11.xxx.xxx
C12.xxx.xxx
Ball Bearing Cages
D
To use with
D
LC
TYPE 1
S
Straight Sleeve
Bearing Bush
B30.xxx.xxx
Treated Aluminium
Supplied with fittings
D
D
Demountable pillar
P21.xxx.xxx page 26
L
TYPE 2
Demountable bush
B40.xxx.xxx
conditions of travel
S
LC
Pillar P10 .xxx.xxx
Page 24
L
S
D
S
X
Demountable pillar
P22.xxx.xx page 27
LC
TYPE 1
Type 1
D1
24
25
Lc
S
30
32
In this assembly the end of the pillar
and the retaining washer can leave
the lower end of the bearing bush,
and all bearings remain pre-loaded
and in contact with the bearing pillar
and bush.
The bearing cage is supplied
complete with a retaining washer and
screw (see page 40).
Lc
S
38
40
Lc
S
48
50
63
Lc
S
30
4.2
32
38
5.8
40
In this assembly the pillar and bearing
cage can leave the top of the bearing
bush completely. At the lower end of
the bearing bush the retaining washer
meets the circlip and the pillar cannot
leave the bearing cage. The bearing
cage is supplied complete with
retaining washer, circlip and screw
(see page 40).
34
C11.024.048
C11.025.048
48
17.5
C11.030.048
C11.032.048
48
17.5
C11.038.048 C11.038.060
C11.040.048 C11.040.060
48
60
17.5
23.5
Lc
S
D1 X
24
4.2
25
Type 2
C11.024.036
C11.025.036
36
11.5
C11.030.036
C11.032.036
36
11.5
48
50
7
63
7
S
D
L
C11.048.070 C11.048.084
C11.050.070 C11.050.084
70
84
28.5
35.5
TYPE 2
L
S
L
S
L
S
L
S
L
S
C12.024.055
C12.025.055
55
27
C12.030.070
C12.032.070
70
35
C12.038.070
C12.040.070
70
36
C12.048.105
C12.050.105
105
51
C12.063.145
145
72
C12.024.070
C12.025.070
70
35
C12.030.090
C12.032.090
90
43
C12.038.085
C12.040.085
85
43
C12.048.120
C12.050.120
120
61
C12.063.165
165
82
C12.024.090
C12.025.090
90
42
C12.030.105
C12.032.105
105
50
C12.038.105
C12.040.105
105
51
C12.048.140
C12.050.140
140
71
C12.063.180
180
92
80mm available on request.
X
C12.024.100
C12.025.100
100
50
C12.030.115
C12.032.115
115
60
C12.038.115
C12.040.115
115
61
C12.048.150
C12.050.150
150
81
C12.063.190
190
105
C12.024.110
C12.025.110
110
60
C12.030.125
C12.032.125
125
70
C12.038.125
C12.040.125
125
71
C12.048.160
C12.050.160
160
91
C12.063.205
205
117
S
C11.063.098
98
42.5
C12.030.135
C12.032.135
135
80
C12.038.135
C12.040.135
135
81
C12.048.170
C12.050.170
170
103
C12.063.215
215
130
X
C12.038.145
C12.040.145
145
91
C12.048.185
C12.050.185
185
116
C12.038.155
C12.040.155
155
103
C12.048.195
C12.050.195
195
128
Guide to Operating Conditions – Type 1
TYPE 1: The Ball Cage remains in the pre-loaded condition throughout the stroke of the press.
C2
EC
Demountable
Bush
3
LB
F
C (Stroke)
Straight
Sleeve Bush
L
Point of
pre-load
H
Shut
height
(Die life
depleted)
LC
LB
E
C1
Start position of assembly bearing cage must be suspended by
retaining washer
h
J1
Assembly at bottom of travel
Assembly at top of travel
J2
CALCULATIONS FOR PILLAR LENGTH
Using bush B30.xxx.xxx
Length of pillar P10 = H – 25
Length of pillar P21 = H – C2 – 25
For EC see pages 26 & 27
Using demountable bush B40.xxx.xxx
Length of Pillar P10 = H – C1 + E – 25
Length of pillar P21 = H – (C1 + C2) + E – 25
For E see page 29
For h see table on page 35
35
Selection Table for Bush and Ball Cage – Type 1
Guide Bushes
Pillar
Diam. Demountable Bush Bearing Bush
B40.xxx.xxx
B30.xxx.xxx
Dn E F LB
LB
35 65
65
50 80
80
24/25 30 65 95
95
110
130
50 80
80
65 95
95
80 110
110
30/32 30
130
150
170
50 80
80
65 95
95
80 110
110
100 130
130
38/40 30
150
170
190
215
65 115
110
80 130
130
100 150
150
120 170
170
48/50 50
190
215
240
265
100 150
150
120 170
170
140 190
190
63 50
215
240
265
Length
of Ball
Cage
LC
36
STROKE “C” (length of travel required)
10
50
100
150
48
36
48
48
60
70
84
98
Selection of the Bush and Cage for Type 1 Bearing Assemblies is based on the Stroke and Pillar diameter. When
these two are known use the table above.
• Select required Pillar diameter.
• Select required Stroke in columns under STROKE “C”.
•M
ove down the Stroke Column to the blue square on the horizontal line opposite to the nominated Pillar diameter
(Dn).
•M
ove to the left on this horizontal and select the length of Bush required under column LB (Demountable or Straight
Sleeve).
•T
o obtain length of the suitable Ball Cage, find the intersection of Bush Length (LB) and Stroke “C” and select the
matching colour in column LC.
Example: Pillar diameter = 50m/m. Stroke = 105m/m. Bush length - 190m/m.
••• Intersection colour = light blue = Cage Length of 70m/m
Note: A
lways ensure adequate clearance between Bush and Die Set Plate or Pillar clamp screws at minimum
daylight. Allow for die wear during the life of the tool.
See page 12 for Pillar length calculations.
36
Guide to Operating Conditions – Type 2
TYPE 2: for applications varying from partial pre-load of the Ball Cages,
to Ball Cage totally free from the Bush, according to selected conditions.
Functioning
conditions
Length of travel is unlimited. Bearing cage leaves the bush
Bearing cage leaves pre-loading but does not leave the bush.
Type 2
Bearing cage remains partly under pre-load
Type 1
Bearing Cage
completly
under pre-load.
FUNCTIONING CONDITIONS
To select bush and ball cage see page 37
To calculate the length of pillar see page 34
C (Stroke)
Above this line
balls are free
Below this line, balls
are in contact with
nominal diameter
3
a
EC C2
Demountable Bush
Type B 40
Length of
pillar
Dn
Dia
pillar
a
h
25
6
9.3
32
6
10.4
40
6
11.5
50
8
12.6
63
8
16
Dn
Straight Sleeve Bush
Type B 30
H
Shut
height
(Die life depleted)
F
LB
LB
LC
E
h
C1
J
37
38
10
50
100
150
200
300
350
400
Example: Operating conditions = Light blue.
Pillar diameter = 40m/m. Stroke = 150m/m.
Demountable or Straight Sleeve Bush = 110m/m.
Ball Cage = 105m/m.
Note: Always ensure adequate clearance between Bush
and Die set plate or Pillar clamp screws at minimum
daylight. Allow for die wear during the life of the tool.
See page 12 for Pillar length calculations.
250
STROKE “C” (length of travel required)
Selection of the Bush and Cage for Type 2 Bearing Assemblies is based on the Operating conditions,
Pillar diameter and Stroke.
• Determine the required operating conditions from page 14 and note the shade of blue in the colour
banding boxes.
• Select required Pillar diameter.
• Select required Stroke in columns under STROKE “C”.
• Move down the Stroke column to the coloured box matching the selected operating conditions and
on the horizontal line opposite to the nominated Pillar diameter (Dn).
• Move to the left on this horizontal and select the length of Bush and Ball Cages from columns LB
(Demountable or Straight Sleeve) and LC.
• Selection of the longest Bush and Ball Cage combination, according to shut height conditions, will
ensure increased life.
Length
Guide Bushes
Pillar
Ball
Diam. Demountable bush Bearing bush ofcage
B40.xxx.xxx
B30.xxx.xxx
Dn E F LB J1 LB J2 LC
35 65 4 65 4 55
50 80 4 80 4 70
24/25 30 65 95 4 95 4 90
110 4 100
130 4 110
50 80 4 80 4 70
65 95 4 95 4 90
80 110 4 110 4 105
30/32 30
130 4 115
150 4 125
170 4 135
50 80 4 80 4 70
65 95 4 95 4 85
80 110 4 110 4 105
100 130 4 130 4 115
38/40 30
150 4 125
170 4 135
190 4 145
215 4 155
65 115 4 110 4 105
80 130 4 130 4 120
100 150 4 150 4 140
120 170 4 170 4 150
48/50 50
190 4 160
215 4 170
240 4 185
265 4 195
100 150 4 150 4 145
120 170 4 170 4 165
140 190 4 190 4 180
63 50
215 4 190
240 4 205
265 4 215
Selection Table for Bush and Ball Cage – Type 2
Pillar Assembly Data
Diameter
pillar
D1
GUIDE PILLARS
P10.xxx.xxx
D1
D
R6
DEMOUNTABLE PILLARS
P21.xxx.xxx
D1
D
R6
Diameter
bore
DR6
19/20
19/20
24/25
24/25
30/32
30/32
38/40
38/40
48/50
48/50
63
63
Diameter
pillar
D1
– 0.011
19/20
– 0.020
– 0.011
24/25
– 0.020
– 0.016
30/32
– 0.025
– 0.016
38/40
– 0.025
– 0.017
48/50
– 0.029
– 0.017
63
– 0.029
Diameter
bore
DR6
– 0.024
19/20
– 0.037
– 0.024
24/25
– 0.037
– 0.029
30/32
– 0.045
– 0.029
38/40
– 0.045
– 0.029
48/50
– 0.045
– 0.035
63
– 0.054
Diameter
pillar
D1
– 0.011
19/20
– 0.020
– 0.011
24/25
– 0.020
– 0.016
30/32
– 0.025
– 0.016
38/40
– 0.025
– 0.017
48/50
– 0.029
– 0.017
63
– 0.029
Diameter
bore
DR6
– 0.024
19/20
– 0.037
– 0.024
24/25
– 0.037
– 0.029
30/32
– 0.045
– 0.029
38/40
– 0.045
– 0.029
48/50
– 0.045
– 0.035
63
– 0.054
– 0.024
– 0.037
– 0.024
– 0.037
– 0.029
– 0.045
– 0.029
– 0.045
– 0.029
– 0.045
– 0.035
– 0.054
Clearance
min.
max.
– 0.004
– 0.026
– 0.004
– 0.026
– 0.004
– 0.029
– 0.004
– 0.029
– 0.000
– 0.028
– 0.006
– 0.037
DEMOUNTABLE PILLARS
- CENTRAL FIXING
P22.xxx.xxx
D1
l 3 min
D
D2
R6
l 4 min
D2
I3
I4
26
25
3.5
33
30
5.5
41
40
5.5
51
51
5.5
64
59
5.5
77
70
5.5
39
Bush Assembly Data
DEMOUNTABLE BUSHES
B10.xxx.xxx
H
D2 6
Dn
D2
STRAIGHT SLEEVE
BALL BEARING BUSHES
B30.xxx.xxx
D2
Bush O/D
Dia
D2
+ 0.021
28 + 0.013
Hole Dia
H6
D2
+ 0.013
28 + 0.000
Clearance
min.
max.
– 0.000
– 0.021
24/25
+ 0.025
38 + 0.016
+ 0.016
38 + 0.000
– 0.000
– 0.025
30/32
+ 0.025
45 + 0.016
+ 0.016
45 + 0.000
– 0.000
– 0.025
38/40
+ 0.030
54 + 0.019
+ 0.019
54 + 0.000
– 0.000
– 0.030
48/50
+ 0.030
65 + 0.019
+ 0.019
65 + 0.000
– 0.000
– 0.030
63
+ 0.035
81 + 0.022
+ 0.022
81 + 0.000
– 0.000
– 0.035
Bush Bore
Dia
Dn
24/25
Bush O/D
Dia
D2
– 0.009
45 – 0.016
Hole Dia
H6
D2
+ 0.016
45 + 0.000
Clearance
min.
max.
+ 0.009
+ 0.032
30/32
– 0.010
54 – 0.018
+ 0.019
54 + 0.000
+ 0.010
+ 0.037
38/40
– 0.010
65 – 0.018
+ 0.019
65 + 0.000
+ 0.010
+ 0.037
48/50
– 0.012
81 – 0.022
+ 0.022
81 + 0.000
+ 0.012
+ 0.044
Bush Bore
Dia
Dn
24/25
Bush O/D
Dia
D2
+ 0.025
45 + 0.016
Hole Dia
H6
D2
+ 0.016
45 + 0.000
Clearance
min.
max.
– 0.000
– 0.025
30/32
+ 0.030
54 + 0.019
+ 0.019
54 + 0.000
– 0.000
– 0.030
38/40
+ 0.030
65 + 0.019
+ 0.019
65 + 0.000
– 0.000
– 0.030
48/50
+ 0.035
81 + 0.022
+ 0.022
81 + 0.000
– 0.000
– 0.035
19/20
g4
Dn
D2
Bush Bore
Dia
Dn
H6
DEMOUNTABLE
BALL BEARING BUSHES
B40.xxx.xxx
Dn
D2
40
H6
Pillar and Bush Accessories
Clamps
B02.00x.000
A
B01.00x.000
A
B
B
C D
Cat. Ref
A
B
C
D
B01.005.000
12.3
12.7
3.2
5.6
B01.006.000
14.3
15.9
4.9
8.7
B01.008.000
19.8
15.9
4.9
9.5
D
C
B02.006.000
18.3
14.5
5
10
B02.008.000
24.6
18.8
5
13
Fixing caps for demountable pillars - P22.xxx.xxx
D2
a
c
b
d
D1
D3
D4
Pillar
Diameter
D1
D2
D3
D4
a
b
c
d
19
20
5.6
9.7
19
25
3.3
4.2
5
2.5
24
25
6.8
11.2
24
32
5
4
6
3
30
32
8.8
14.2
30
40
5
7
8
4
38
40
48
10.8
17.2
38
50
5
10
10
5
50
12.8
19.2
48
63
5
13
12
6
63
80
17
25.5
63
76
5
19
16
8
21
31.5
80
93
5
25
20
10
Accessories for Ball Bearing Assemblies
Retaining washer
TYPE 1
Pillar
Diameter
24
25
30
32
38
40
48
50
63
Type 1
C01.024.001
C01.025.001
C01.030.001
C01.032.001
C01.038.001
C01.040.001
C01.048.001
C01.050.001
C01.063.001
Retaining washer
TYPE 2
Washer TYPE 2
Screws for fixing
DIN 7380 for
diameter 24 to
50 DIN 7984 for
diameter 63
To use with the assemblies
Type 2
Type 2
Type 1 & 2
C02.024.001
C02.025.002
M6 x 20
C02.025.001
C02.030.001
C02.032.002
M8 x 20
C02.032.001
C02.038.001
C02.040.002
M10 x 25
C02.040.001
C02.048.001
C02.050.002
M12 x 30
C02.050.001
C02.063.001
C02.063.002
M16 x 35
Circlips TYPE 2
Type 2
C02.024.003
C02.025.003
C02.030.003
C02.032.003
C02.038.003
C02.040.003
C02.048.003
C02.050.003
C02.063.003
41
S11.xxx.xxx
Colour: Green
Light Load Springs
DIAMETERS:
From 10 to 16 mm d
Section of wire: round
D
Lo
LOAD TABLE
Hole Rod Free
MAX.
Rate daN
SPRING
dia. dia. Length
WORKING
TRAVEL
Mm Mm mm REFERENCE necessary TRAVEL
to travel
TO SOLID
(40%
of
Lo)
1mm of C
Load Travel Load Travel
D
d
Lo
daN mm daN mm
4.6 10.2 5.8 13
0.45
S11.010.025
25
4.4 12.5 5.6 16
0.35
S11.010.032
32
15 5.6 20
4.2
0.28
S11.010.038
38
18 5.6 23
4.6
0.24
S11.010.044
44
10 5
20 5.6 27
4.2
0.21
S11.010.051
51
25 5.5 34
4.0
0.16
S11.010.064
64
30 5.3 40
3.9
0.13
S11.010.076
76
3.7 122.5 54.9 163
0.03
305 S11.010.305
12.5 6.3
25
32
38
44
51
64
76
89
305
S11.012.025
S11.012.032
S11.012.038
S11.012.044
S11.012.051
S11.012.064
S11.012.076
S11.012.089
S11.012.305
0.89
0.67
0.55
0.46
0.39
0.30
0.25
0.21
0.06
9.1
8.4
8.3
8.3
7.8
7.5
7.5
7.6
7.3
10.2
12.5
15
18
20
25
30
36
122
11.6 13
11.4 17
11.0 20
10.6 23
10.5 27
10.5 35
10.3 41
10.3 49
10.0 166
16
25
32
38
44
51
64
76
89
102
305
S11.016.025
S11.016.032
S11.016.038
S11.016.044
S11.016.051
S11.016.064
S11.016.076
S11.016.089
S11.016.102
S11.016.305
1.79
1.34
1.06
0.87
0.76
0.59
0.48
0.40
0.35
0.11
18.3
16.8
15.9
15.7
15.2
14.8
14.4
14.0
14.3
13.4
10.2
12.5
15
18
20
25
30
35
41
122
23 13
21 16
21 20
20 23
20 27
20 34
19.7 41
19.6 49
19.6 56
18.7 170
8
d
DIAMETERS:
From 20 to 63 mm
Section of wire:
rectangular
D
LOAD TABLE
Hole Rod Free
MAX.
Rate daN
SPRING
dia. dia. Length
WORKING
TRAVEL
Mm Mm mm REFERENCE necessary TRAVEL
to travel
TO
SOLID
1mm of C (40% of Lo)
Load Travel Load Travel
D
d
Lo
daN mm daN mm
109 10.2 139 13
10.7
S11.025.025
25
101 12.5 130 16
8.1
S11.025.032
32
15 124 19
98
6.5
S11.025.038
38
18 122 23
95
5.3
S11.025.044
44
20 115 25
92
4.6
S11.025.051
51
25 112 31
90
3.6
S11.025.064
64
30 112 39
88
2.92
S11.025.076
76
35 112 46
86
2.46
S11.025.089
89
25 12.5 102 S11.025.102
41 110 52
87
2.12
46 110 59
86
1.87
115 S11.025.115
51 110 66
85
1.67
127 S11.025.127
56 112 74
85
1.52
140 S11.025.140
61 110 80
85
1.40
152 S11.025.152
71 110 93
85
1.20
178 S11.025.178
81 110 107
85
1.05
203 S11.025.203
85 122 110 160
0.70
305 S11.025.305
32
40
16
38
44
51
64
76
89
102
115
127
140
152
178
203
254
305
S11.032.038
S11.032.044
S11.032.051
S11.032.064
S11.032.076
S11.032.089
S11.032.102
S11.032.115
S11.032.127
S11.032.140
S11.032.152
S11.032.178
S11.032.203
S11.032.254
S11.032.305
10.1
8.3
7.1
5.5
4.6
3.9
3.4
3.0
2.62
2.38
2.19
1.82
1.59
1.25
1.04
152
149
142
138
138
137
139
138
134
133
134
129
128
128
127
15
18
20
25
30
35
41
46
51
56
61
71
81
102
122
192
183
178
176
175
175
175
174
170
171
170
165
165
163
161
19
22
25
32
39
45
52
58
65
72
78
88
104
130
155
20
51
64
76
89
102
115
127
140
152
178
203
254
305
S11.040.051
S11.040.064
S11.040.076
S11.040.089
S11.040.102
S11.040.115
S11.040.127
S11.040.140
S11.040.152
S11.040.178
S11.040.203
S11.040.254
S11.040.305
10.6
8.0
6.6
5.6
4.8
4.2
3.8
3.4
3.1
2.6
2.3
1.80
1.48
212
200
198
196
197
193
194
190
189
185
186
184
181
20
25
30
35
41
46
51
56
61
71
81
102
122
265
256
250
250
245
243
243
241
241
240
240
236
226
25
32
38
45
51
58
65
71
71
92
105
131
157
25
64
76
89
102
115
127
140
152
178
203
254
305
S11.050.064
S11.050.076
S11.050.089
S11.050.102
S11.050.115
S11.050.127
S11.050.140
S11.050.152
S11.050.178
S11.050.203
S11.050.254
S11.050.305
15.7
12.6
10.5
9.0
9.0
7.0
6.3
5.7
4.8
4.2
3.3
2.7
393
378
368
369
369
357
353
348
341
340
337
329
25
30
35
41
41
51
56
61
71
81
102
122
502
491
473
468
468
455
446
445
441
437
429
421
32
39
45
52
52
65
72
78
92
104
130
156
38
76
89
102
115
127
152
178
203
254
305
S11.063.076
S11.063.089
S11.063.102
S11.063.115
S11.063.127
S11.063.152
S11.063.178
S11.063.203
S11.063.254
S11.063.305
19.3
15.8
13.4
11.6
10.2
8.4
7.0
6.0
4.7
3.9
579
553
549
534
520
512
497
486
479
476
30
35
41
46
51
61
71
81
102
122
733
695
670
661
653
638
623
612
592
592
38
44
50
57
64
76
89
102
126
152
Lo
LOAD TABLE
Hole Rod Free
MAX.
Rate daN
SPRING
dia. dia. Length
WORKING
TRAVEL
Mm Mm mm REFERENCE necessary TRAVEL
to travel
TO SOLID
(40%
of
Lo)
1mm of C
Load Travel Load Travel
D
d
Lo
daN mm daN mm
57 10.2 73 13
5.5
S11.020.025
25
54 12.5 69 16
4.2
S11.020.032
32
15 65 19
51
3.3
S11.020.038
38
18 64 23
51
2.77
S11.020.044
44
20 64 26
50
2.45
S11.020.051
51
25 62 32
49
1.90
S11.020.064
64
30 62 40
48
1.61
S11.020.076
76
20 10
35 62 46
47
1.34
S11.020.089
89
41 62 53
48
1.18
102 S11.020.102
46 62 60
48
1.04
115 S11.020.115
51 62 67
47
0.93
127 S11.020.127
56 62 73
48
0.85
140 S11.020.140
61 62 81
48
0.79
152 S11.020.152
46 122 61 162
0.38
305 S11.020.305
50
63
RATE: 1 dekanewton (daN) approximately equal to 1 kg (Force) or 1 Kilopound (Kp) – 1 daN = 1.0197 kg (Force) = 1.0197 Kp
42
Intermediate Load Springs
DIAMETERS:
From 10 to 16 mm d
Section of wire: round
D
Lo
LOAD TABLE
Hole Rod Free
MAX.
Rate daN
SPRING
dia. dia. Length
WORKING
TRAVEL
Mm Mm mm REFERENCE necessary TRAVEL
to travel
TO SOLID
(37.5%
of
Lo)
1mm of C
Load Travel Load Travel
D
d
Lo
daN mm daN mm
11.8 9.4 13.0 11
1.26
S21.010.025
25
11.8 12 12.8 13
0.98
S21.010.032
32
11.1 14 12.6 16
0.79
S21.010.038
38
10.9 16.5 12.5 19
0.66
S21.010.044
44
10 5
10.8 19 12.2 21
0.57
S21.010.051
51
10.8 24 12.2 27
0.45
S21.010.064
64
10.4 28 12.2 33
0.37
S21.010.076
76
10.3 114 12.2 136
0.09
305 S21.010.305
12.5 6.3
25
32
38
44
51
64
76
89
305
S21.012.025
S21.012.032
S21.012.038
S21.012.044
S21.012.051
S21.012.064
S21.012.076
S21.012.089
S21.012.305
2.28
1.75
1.43
1.18
1.02
0.79
0.65
0.55
0.15
21.4
21.0
20.0
19.5
19.4
19.0
18.2
18.2
17.1
9.4
12
14
16.5
19
24
28
33
114
23.0 11
22.8 13
22.8 16
22.5 19
22.4 22
22.1 28
22.0 34
22.6 41
21.6 144
16
25
32
38
44
51
64
76
89
102
305
S21.016.025
S21.016.032
S21.016.038
S21.016.044
S21.016.051
S21.016.064
S21.016.076
S21.016.089
S21.016.102
S21.016.305
3.38
2.50
2.01
1.67
1.42
1.10
0.90
0.76
0.66
0.21
31.8
30.0
28.1
27.6
27.0
26.4
25.2
25.1
25.1
23.9
9.4
12
14
16.5
19
24
28
33
38
114
33.8 11
32.8 13
32.2 16
30.8 19
30.0 21
29.7 27
29.7 33
29.6 39
29.6 45
29.0 138
8
d
DIAMETERS:
From 20 to 63 mm
Section of wire:
rectangular
Hole
dia.
Mm
D
20
D
Colour: Blue
LOAD TABLE
Hole Rod Free
MAX.
Rate daN
SPRING
dia. dia. Length
WORKING
TRAVEL
Mm Mm mm REFERENCE necessary TRAVEL
to travel
TO
SOLID
1mm of C (35% of Lo)
Load Travel Load Travel
D
d
Lo
daN mm daN mm
157 9.4 184 11
16.7
S21.025.025
25
150 12 170 13
12.5
S21.025.032
32
139 14 158 16
9.9
S21.025.038
38
137 16.5 158 19
8.3
S21.025.044
44
137 19 156 21
7.2
S21.025.051
51
132 24 151 27
5.5
S21.025.064
64
126 28 148 33
4.5
S21.025.076
76
125 33 148 39
3.8
S21.025.089
89
25 12.5 102 S21.025.102
125 38 145 44
3.3
125 43 145 50
2.91
115 S21.025.115
126 48 145 56
2.63
127 S21.025.127
123 52 149 63
2.36
140 S21.025.140
124 57 145 67
2.17
152 S21.025.152
123 67 145 79
1.84
178 S21.025.178
122 76 144 90
1.60
203 S21.025.203
120 114 142 135
1.05
305 S21.025.305
32
40
16
38
44
51
64
76
89
102
115
127
140
152
178
203
254
305
S21.032.038
S21.032.044
S21.032.051
S21.032.064
S21.032.076
S21.032.089
S21.032.102
S21.032.115
S21.032.127
S21.032.140
S21.032.152
S21.032.178
S21.032.203
S21.032.254
S21.032.305
16.6
13.6
11.6
8.8
7.1
6.0
5.2
4.6
4.2
3.7
3.4
2.91
2.52
2.00
1.66
232
224
220
211
199
198
198
198
202
192
194
195
192
190
189
14
16.5
19
24
28
33
38
43
48
52
57
67
76
95
114
266
258
244
238
227
222
222
222
222
222
222
222
222
220
220
16
19
21
27
32
37
43
49
55
60
66
77
88
110
133
20
51
64
76
89
102
115
127
140
152
178
203
254
305
S21.040.051
S21.040.064
S21.040.076
S21.040.089
S21.040.102
S21.040.115
S21.040.127
S21.040.140
S21.040.152
S21.040.178
S21.040.203
S21.040.254
S21.040.305
17.1
12.9
10.5
8.8
7.6
6.7
5.0
5.4
4.9
4.2
3.6
2.89
2.38
325
310
294
290
289
288
288
281
279
281
274
275
271
19
24
28
33
38
43
48
52
57
67
76
95
114
359
335
335
326
326
322
322
319
318
318
315
315
312
21
26
32
37
43
48
54
59
65
76
87
110
131
25
64
76
89
102
115
127
140
152
178
203
229
254
305
S21.050.064
S21.050.076
S21.050.089
S21.050.102
S21.050.115
S21.050.127
S21.050.140
S21.050.152
S21.050.178
S21.050.203
S21.050.229
S21.050.254
S21.050.305
21.2
16.7
14.0
12.2
10.7
9.5
8.6
7.8
6.6
5.7
5.1
4.6
3.8
509
468
462
464
460
456
447
445
442
433
439
437
433
24
28
33
38
43
48
52
57
67
76
86
95
114
566
532
525
525
525
513
507
508
506
506
506
506
504
27
32
37
43
49
54
59
66
77
88
100
117
134
38
76
89
102
115
127
152
178
203
229
254
305
S21.063.076
S21.063.089
S21.063.102
S21.063.115
S21.063.127
S21.063.152
S21.063.178
S21.063.203
S21.063.229
S21.063.254
S21.063.305
30.4
25.0
21.2
18.6
16.4
13.3
11.2
9.6
8.5
7.7
6.3
851
825
806
800
787
758
750
730
731
732
718
28
3
38
43
48
57
67
76
86
95
114
973
950
933
930
918
891
874
865
865
865
865
32
38
44
50
56
67
78
90
102
115
138
Lo
LOAD TABLE
Rod Free
MAX.
Rate daN
SPRING
dia. Length
WORKING
TRAVEL
Mm mm REFERENCE necessary TRAVEL
to travel
TO SOLID
(35%
of
Lo)
1mm of C
Load Travel Load Travel
d
Lo
daN mm daN mm
84.8 9.4 99 11
9.02
S21.020.025
25
80.0 12 90 13
6.67
S21.020.032
32
76.7 14 88 16
5.48
S21.020.038
38
73.4 16.5 85 19
4.45
S21.020.044
44
74.9 19 83 21
3.94
S21.020.051
51
72.7 24 82 27
3.03
S21.020.064
64
69.7 28 82 33
2.49
S21.020.076
76
10
70.6 33 82 39
2.14
S21.020.089
89
69.9 38 81 44
1.84
102 S21.020.102
70.1 43 80 49
1.63
115 S21.020.115
70.1 48 80 55
1.46
127 S21.020.127
69.0 52 80 61
1.32
140 S21.020.140
69.0 57 80 66
1.21
152 S21.020.152
69.5 114 80 136
0.61
305 S21.020.305
S21.xxx.xxx
50
63
RATE: 1 dekanewton (daN) approximately equal to 1 kg (Force) or 1 Kilopound (Kp) – 1 daN = 1.0197 kg (Force) = 1.0197 Kp
43
S26.xxx.xxx
Colour: Red
Heavy Load Springs
DIAMETERS:
From 10 to 16 mm d
Section of wire: round
D
Lo
LOAD TABLE
Hole Rod Free
MAX.
Rate daN
SPRING
dia. dia. Length
WORKING
TRAVEL
Mm Mm mm REFERENCE necessary TRAVEL
to travel
TO SOLID
(30%
of
Lo)
1mm of C
Load Travel Load Travel
D
d
Lo
daN mm daN mm
16.0 7.5 19 8.9
2.13
S26.010.025
25
15.5 9.6 19 11.7
1.64
S26.010.032
32
14.5 11 18.5 14
1.33
S26.010.038
38
14.5 13 18.5 17
1.13
S26.010.044
44
10 5
14.5 15 18.5 19
0.98
S26.010.051
51
14.5 19 18.5 25
0.78
S26.010.064
64
14.5 23 18 29
0.63
S26.010.076
76
13.5 91 18 120
0.15
305 S26.010.305
12.5 6.3
25
32
38
44
51
64
76
89
305
S26.012.025
S26.012.032
S26.012.038
S26.012.044
S26.012.051
S26.012.064
S26.012.076
S26.012.089
S26.012.305
3.9
3.0
2.42
2.01
1.77
1.38
1.14
0.96
0.27
29
28
27
26
27
26
26
25.9
24.5
7.5
9.6
11
13
15
19
23
27
91
34
33
32
32
32
32
32
32
32
8.7
11.0
13.5
16
19
24
29
33
120
16
25
32
38
44
51
64
76
89
102
305
S26.016.025
S26.016.032
S26.016.038
S26.016.044
S26.016.051
S26.016.064
S26.016.076
S26.016.089
S26.016.102
S26.016.305
8.7
6.4
5.2
4.2
3.64
2.84
2.33
1.98
1.72
0.54
65
61
57
55
55
54
54
53
53
49
7.5
9.6
11
13
15
19
23
27
31
91
76
70
70
66
66
66
66
66
66
66
8.7
11
13.7
15.7
18.5
23.5
29
34.5
40
122
8
d
DIAMETERS:
From 20 to 50 mm
Section of wire:
rectangular
LOAD TABLE
Hole Rod Free
MAX.
Rate daN
SPRING
dia. dia. Length
necessary WORKING
TRAVEL
Mm Mm mm REFERENCE
TRAVEL
to travel
TO SOLID
1mm of C (30% of Lo)
Load Travel Load Travel
D
d
Lo
daN mm daN mm
265 9.6 290 10.5
27.6
S26.025.032
32
242 11 286 13
22.0
S26.025.038
38
239 13 285 15.5
18.4
S26.025.044
44
236 15 283 18
15.7
S26.025.051
51
232 19 275 22.5
12.2
S26.025.064
64
230 23 275 27.5
10.0
S26.025.076
76
227 27 275 32.5
8.4
S26.025.089
89
229 31 275 32.5
7.4
25 12.5 102 S26.025.102
228 35 275 42.7
6.5
115 S26.025.115
220 38 273 47
5.8
127 S26.025.127
143 42 167 49
3.4
140 S26.025.140
221 46 273 57.5
4.8
152 S26.025.152
217 53 273 68
4.1
178 S26.025.178
219 61 273 77
3.59
203 S26.025.203
220 91 273 115
2.42
305 S26.025.305
32
D
20
44
37.6
31.0
26.3
20.5
16.6
13.9
12.1
10.6
9.6
8.6
7.9
6.7
5.8
4.6
3.8
414
403
394
389
382
375
375
371
365
361
363
355
354
350
346
11
13
15
19
23
27
31
35
38
42
46
53
61
76
91
451
440
435
435
430
425
425
425
425
430
425
420
420
420
420
20
51
64
76
89
102
115
127
140
152
178
203
254
305
S26.040.051
S26.040.064
S26.040.076
S26.040.089
S26.040.102
S26.040.115
S26.040.127
S26.040.140
S26.040.152
S26.040.178
S26.040.203
S26.040.254
S26.040.305
34.9
26.6
21.5
18.0
15.7
13.8
12.4
11.3
10.2
8.7
7.6
6.0
5.0
524
505
495
486
487
483
471
475
469
461
464
456
455
15
19
23
27
31
35
38
42
46
53
61
76
91
593 17
585 22
580 27
575 32
575 37
575 42
575 47
588 52
575 57.5
575 67
575 76
575 97
575 116
25
64
76
89
102
115
127
140
152
178
203
254
305
S26.050.064
S26.050.076
S26.050.089
S26.050.102
S26.050.115
S26.050.127
S26.050.140
S26.050.152
S26.050.178
S26.050.203
S26.050.254
S26.050.305
42.3
33.8
28.1
24.5
21.5
18.9
16.9
15.4
13.2
11.5
9.0
7.5
804
777
759
760
753
718
710
708
700
701
684
683
19
23
27
31
35
38
42
46
53
61
76
91
910 21.5
879 26
860 30.5
860 35
860 40
850 45
845 50
830 54
830 64
830 72.5
825 92
825 112
Lo
40
Hole
dia.
Mm
16
S26.032.038
S26.032.044
S26.032.051
S26.032.064
S26.032.076
S26.032.089
S26.032.102
S26.032.115
S26.032.127
S26.032.140
S26.032.152
S26.032.178
S26.032.203
S26.032.254
S26.032.305
D
LOAD TABLE
Rod Free
MAX.
Rate daN
SPRING
dia. Length
WORKING
TRAVEL
Mm mm REFERENCE necessary TRAVEL
to travel
TO SOLID
(30%
of
Lo)
1mm of C
Load Travel Load Travel
d
Lo
daN mm daN mm
173 7.5 194 8.4
23.1
S26.020.025
25
167 9.6 183 10.5
17.4
S26.020.032
32
153 11 174 12.5
13.9
S26.020.038
38
148 13 165 14.5
11.4
S26.020.044
44
147 15 162 16.5
9.8
S26.020.051
51
146 19 162 21
7.7
S26.020.064
64
145 23 162 26
6.3
S26.020.076
76
10
145 27 162 30
5.4
S26.020.089
89
145 31 162 35
4.7
102 S26.020.102
144 35 162 40
4.1
115 S26.020.115
141 38 162 44
3.7
127 S26.020.127
143 42 167 49
3.4
140 S26.020.140
141 46 162 53
3.08
152 S26.020.152
137 91 162 108
1.50
305 S26.020.305
50
12
14
16.5
21.5
26
30.5
35.5
40.5
45
50
54
63
72
92
110
38
44
51
64
76
89
102
115
127
140
152
178
203
254
305
Extra Heavy Load Springs
D
d
DIAMETERS:
From 10 to 50 mm
Section of wire:
rectangular
Lo
LOAD TABLE
Hole Rod Free
MAX.
Rate daN
SPRING
dia. dia. Length
WORKING
necessary
TRAVEL
Mm Mm mm REFERENCE
TRAVEL
to travel
TO SOLID
(25% of Lo)
1mm of C
Load Travel Load Travel
D
d
Lo
daN mm daN mm
20.3 6.2 29.5 8.7
3.27
S36.010.025
25
20.0 8.0 27.0 10.5
2.50
S36.010.032
32
20.1 9.5 27.0 13.2
2.12
S36.010.038
38
19.5 11 26.5 15.0
1.77
S36.010.044
44
10 5
19.9 13 26.5 17.0
1.53
S36.010.051
51
19.5 16 26.5 21.5
1.22
S36.010.064
64
19.2 19 26.5 26.5
1.01
S36.010.076
76
19.0 76 26.0 106
0.25
305 S36.010.305
12.5 6.3
16
8
25
32
38
44
51
64
76
89
305
S36.012.025
S36.012.032
S36.012.038
S36.012.044
S36.012.051
S36.012.064
S36.012.076
S36.012.089
S36.012.305
5.87
4.43
3.63
3.06
2.71
2.17
1.77
1.51
0.42
36.4
35.4
34.5
33.7
35.2
34.7
33.6
33
31.9
6.2
8.0
9.5
11
13
16
19
22
76
53
48
47
47
47
47
47
50
47
9.0
10.8
13
15.5
18
22
27
33
112
25
32
38
44
51
64
76
89
102
305
S36.016.025
S36.016.032
S36.016.038
S36.016.044
S36.016.051
S36.016.064
S36.016.076
S36.016.089
S36.016.102
S36.016.305
12.6
9.3
7.5
6.3
5.5
4.3
3.52
3.00
2.61
0.85
78
74
71
69
72
69
67
66
68
65
6.2
8.0
9.5
11
13
16
19
22
26
76
113
103
98
96
96
95
94
94
94
94
9
10.8
13
15
18
22
26.5
31.5
36.5
110
S36.xxx.xxx
Colour: Yellow
LOAD TABLE
Hole Rod Free
MAX.
Rate daN
SPRING
dia. dia. Length
necessary WORKING
TRAVEL
Mm Mm mm REFERENCE
TRAVEL
to travel
TO SOLID
1mm of C (25% of Lo)
Load Travel Load Travel
D
d
Lo
daN mm daN mm
32
S36.025.032
35.4
283 8.0 354 10
38
S36.025.038
28.0
266 9.5 336 12
44
S36.025.044
23.2
255 11 325 14
51
S36.025.051
19.8
257 13 317 16
64
S36.025.064
15.4
246 16 316 21
76
S36.025.076
12.5
238 19 313 25
89
S36.025.089
10.5
231 22 310 29
25 12.5 102 S36.025.102
9.1
237 26 310 34
115 S36.025.115
8.1
235 29 310 39
127 S36.025.127
7.2
230 32 310 43
140 S36.025.140
6.6
231 35 317 48
152 S36.025.152
6.0
228 38 310 53
178 S36.025.178
5.1
224 44 310 62
203 S36.025.203
4.5
230 51 310 70
305 S36.025.305
2.96
225 76 310 108
32
40
16
38
44
51
64
76
89
102
115
127
140
152
178
203
254
305
S36.032.038
S36.032.044
S36.032.051
S36.032.064
S36.032.076
S36.032.089
S36.032.102
S36.032.115
S36.032.127
S36.032.140
S36.032.152
S36.032.178
S36.032.203
S36.032.254
S36.032.305
48.9
40.5
34.6
26.7
21.6
18.2
15.6
13.6
12.2
11.2
10.1
8.6
7.5
6.0
5.0
465
446
450
427
410
400
406
394
390
392
394
478
383
384
480
9.5
11
13
16
19
22
26
29
32
35
38
44
51
64
76
558
547
535
535
525
525
525
500
500
526
500
500
500
500
500
11
13
15
20
24
29
29
36
41
47
50
59
68
85
103
20
51
64
76
89
102
115
127
140
152
178
203
254
305
S36.040.051
S36.040.064
S36.040.076
S36.040.089
S36.040.102
S36.040.115
S36.040.127
S36.040.140
S36.040.152
S36.040.178
S36.040.203
S36.040.254
S36.040.305
56.0
42.2
34.3
28.2
24.4
21.4
19.0
17.1
15.6
13.2
11.4
9.1
7.5
714
675
652
620
634
621
608
599
593
581
581
582
570
13
16
19
22
26
29
32
35
38
44
51
64
76
840
820
815
800
800
792
780
787
780
765
765
765
760
15
19
24
28
33
37
41
46
50
58
67
85
102
RATE: 1 dekanewton (daN) approximately equal to 1 kg (Force) or 1 Kilopound (Kp) – 1 daN = 1.0197 kg (Force) = 1.0197 Kp
45
Urethane Rod
Urethane Tubes
L
L
D
Dia.
D
3
/8
1
/2
5
/8
3
/4
7
/8
1
11/8
11/4
11/2
13/4
2
21/2
3
31/2
4
5
6
61/2
8
46
Length
L
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
Dia.
D
9.5
12.5
16.0
19.0
22.0
25.0
28.0
32.0
38.0
44.5
51.0
63.5
76.0
86.0
102.0
127.0
Length
L
305
305
305
305
305
305
305
305
305
305
305
305
305
305
305
305
A
D
Dia.
D
16
19
20
25
25
32
40
44
50
50
63
63
80
80
100
100
Dia.
A
6.5
9.5
8.5
9.5
10.5
13.5
13.5
13.5
17
23
17
26
21
32
21
40
Length
L
150
300
300
300
300
300
300
300
400
400
400
400
400
400
400
400
Urethane Strippers
L
L
D
D
Symbol
No.
PS187
PS250
PS312
PS375
PS500
PS562
PS625
PS750
PS875
Dia.
A
3
/16
1
/4
5
/16
3
/8
1
/2
9
/16
5
/8
3
/4
7
/8
A
A
Dia.
D
11
/16
3
/4
13
/16
7
/8
1
11/8
11/8
11/2
13/4
Length
L
11/2
2
2
2
21/4
21/4
21/4
3
3
Symbol
No.
SM04
SM05
SM06
SM08
SM10
SM13
SM16
SM19
SM20
Example order: 4 off PS18
Dia.
A
4
5
6
8
10
13
16
19
20
Dia.
D
17
18
19
21
23
26
30
38
38
Length
L
40
50
65
70
70
70
70
70
70
Example order: 4 off SM25
H
G
E
B
C
F
D
A
47
Urethane Springs
Da
Di
Po=O
Db
f
Pn
Lo
Material Polyurethane
Shore Hardness 90A
P = Force (Kilo) f = deflection (mm) Db = bulge diameter (mm)
Da
16
Di
6.5
20
8.5
25
10.5
32
13.5
40
13.5
50
17
63
17
80
21
Lo
12
16
20
25
16
20
25
32
20
25
32
40
32
40
50
63
32
40
50
63
80
32
40
50
63
80
100
32
40
50
63
80
100
125
32
40
50
63
80
100
125
P
32
35
35
33
95
85
80
70
125
120
110
110
150
135
135
135
400
350
300
320
280
400
425
350
320
300
250
780
800
550
620
700
760
750
1600
1300
1200
1200
1150
1100
1050
Example order: 1 off 16-12
48
f
1.2
1.6
2.0
2.5
1.6
2.0
2.5
3.2
2.0
2.5
3.2
4.0
3.2
4.0
5.0
6.3
3.2
4.0
5.0
6.3
8.0
3.2
4.0
5.0
6.3
8.0
10.0
3.2
4.0
5.0
6.3
8.0
10.0
12.5
3.2
4.0
5.0
6.3
8.0
10.0
12.5
Db
17
P
52
52
52
50
21 115
115
110
100
27 175
165
160
150
34 250
215
215
215
42 530
480
480
450
430
52.5 650
625
600
580
530
500
66 1200
1050
1000
1150
1100
1050
1000
86 2200
1700
1800
1800
1700
1650
1600
f
Db
P
f
2.4
1.8 17.5 66
3.2
70
2.4
4.0
70
3.0
5.0
70
3.75
22 150 3.2
2.4
145 4.0
3.0
135 5.0
3.75
130 6.4
4.8
28 225 4.0
3.0
215 5.0
3.75
210 6.4
4.8
200 8.0
6.0
35 330 6.4
4.8
300 8.0
6.0
300 10.0
7.5
310 12.6
9.45
44 650 6.4
4.8
600 8.0
6.0
650 10.0
7.5
610 12.6
9.54
600 16.0
12.0
4.8 54.5 880 6.4
800 8.0
6.0
850 10.00
7.5
800 12.6
9.45
750 16.0
12.0
770 20.0
15.0
69 1400 6.4
4.8
1500 8.0
6.0
1350 10.0
7.5
1450 12.6
9.45
1470 16.0
12.0
1380 20.0
15.0
1380 25.0
18.75
90 2800 6.4
4.8
2300 8.0
6.0
2600 10.0
7.5
2500 12.6
9.45
2200 16.0
12.00
2300 20.0
15.0
2100 25.0
18.75
Db
18
23
28
37
46
57
72
94
P
80
90
90
87
180
175
165
160
275
265
260
240
430
385
385
400
850
780
820
800
760
1250
1200
1100
1080
1080
1080
1900
1850
1850
1980
1850
1830
1850
3650
3200
3500
3300
3000
3100
2800
f
Db
P
f
3.6
19
98
3.0
115 4.8
4.0
110 6.0
5.0
108 7.5
6.25
24 210 4.8
6.0
210 6.0
5.0
200 7.5
6.25
190 9.6
8.0
5.0 30.5 340 6.0
325 7.5
6.25
315 9.6
8.0
290 12.0
10.0
39 520 9.6
8.0
490 12.0
10.0
490 15.0
12.5
530 18.9
15.75
48 1040 9.6
8.0
950 12.0
10.0
1020 15.0
12.5
1000 18.9
15.75
970 24.0
20.0
8.0 59.5 1600 9.6
1600 12.0
10.0
1500 15.0
12.5
1450 18.9
15.75
1430 24.0
20.0
1500 30.0
25.0
75 2600 9.6
8.0
2300 12.0
10.0
2500 15.0
12.5
2700 18.9
15.75
2350 24.0
20.0
2500 30.0
25.0
2450 37.5
31.25
97 4800 9.6
8.0
4200 12.0
10.0
4700 15.0
12.5
4500 18.9
15.75
4100 24.0
20.0
4050 30.0
25.0
3800 37.5
31.25
Db
20
25
32
41
50
62
78
101
Code
Number
16x12
16x16
16x20
16x25
20x16
20x20
20x25
20x32
25x20
25x25
25x32
25x40
32x32
32x40
32x50
32x63
40x32
40x40
40x50
40x63
40x80
50x32
50x40
50x50
50x63
50x80
50x100
62x32
63x40
63x50
63x63
63x80
63x100
63x125
80x32
80x40
80x50
80x63
80x80
80x100
80x125
Urethane Sheet and Blocks
L
T
W
IMPERIAL
W
x
(ins)
L
METRIC
x
(ins)
T
W
(ins)
(mm)
x
L
T
x
(mm)
T
x
(ins)
W
x
(ins)
L
(ins)
(mm)
5
/8
x
5
/8
x
24
/8
x
5
/8
x
12
12
x
12
x
4(mm)
500
x
500
x
10
5
12
x
12
x
5(mm)
500
x
500
x
12
3
/4
x
3
/4
x
24
12
x
12
x
1
/4
500
x
500
x
16
3
/4
x
3
/4
x
12
12
x
12
x
3
/8
500
x
500
x
20
1
x
7
/8
x
24
12
x
12
x
1
/2
500
x
500
x
25
1
x
7
/8
x
12
12
x
12
x
7
/8
500
x
500
x
30
1
x
1
x
24
12
x
12
x
1
500
x
500
x
35
1
x
1
x
12
12
x
12
x
11/2
500
x
500
x
40
11/2
x
3
/4
x
24
12
x
12
x
2
500
x
500
x
45
11/2
x
3
/4
x
12
12
x
12
x
3
500
x
500
x
50
11/2
x
11/2
x
24
12
x
18
x
1
/2
500
x
500
x
60
11/2
x
11/2
x
12
12
x
24
x
1
/2
500
x
500
x
70
2
x
1
x
24
12
x
24
x
3
/4
2
x
1
x
12
12
x
24
x
1
2
x
2
x
24
12
x
24
x
11/2
Example order: 1 off 12” x 12” x 4
Tolerance ± 2mm
2
x
2
x
12
23/8
x
23/8
x
24
23/8
x
23/8
x
12
3
x
11/2
x
24
3
x
11/2
x
12
3
x
2
x
24
3
x
2
x
12
3
x
3
x
24
3
x
3
x
12
41/2
x
21/2
x
24
41/2
x
21/2
x
12
49
Notes
50
Notes
51
Certificate No. Q 09086
produced by: www.drukujcie.com.pl
Cosford Lane, Rugby. CV21 1QN, UK
Tel: +44 (0)1788 542271, Fax: +44 (0)1788 561256
Email: sales@awprecision.com, Web: www.awprecision.com