Underwriters Laboratories (UL LLC) Safety Certification Report Model: 0762-xxxx Device Description: Programmable Controller Applicant: WAGO KONTAKTTECHNIK GMBH & CO KG HANSASTRASSE 27 MINDEN , 32423 DE Manufacturer: Same as Applicant Manufacturing Facility(ies): Same as Applicant WAGO CORP N120 W19129 FREISTADT RD PO BOX 1015 GERMANTOWN, WI53022-8215US USA WAGO & CONTROLS (INDIA) LTD C-27 PHASE III GAUTAM BUDH NAGAR, SECTOR 58 NOIDA UP201301IN India WAGO ELECTRONIC (TIANJIN) CO LTD NO 5 QUANHUI RD WUQING DEVELOPMENT AREA 301700CN TIANJIN ELREST AUTOMATIONSSYSTEME GMBH LEIBNIZSTR 10 KIRCHHEIM/TECK, 73230DE Germany Report No.: E175199-D1001-1/A0/C0-UL Report (Re)Issue Date: 2016-1-28 Base Standard(s): UL 61010-1, 3rd Edition, 2012-05, CAN/CSA-C22.2 No. 61010-1, 3rd Edition, 2012-05 Report Types: This report consists of the following report types: [ Yes ] US Certification (UL Listing) [ Yes ] CAN Certification (cUL Listing) This report covers the Safety evaluation of the referenced model(s) according to the standard(s) specified above. Page ii Report No.: E175199-D1001-1/A0/C0-UL Table of Contents IEC REPORT: ................................................................................................................................................................ 1 Test Report ................................................................................................................................................................ 1 TABLE: List of critical components ...................................................................................................................... 44 National Differences................................................................................................................................................. 46 APPENDIX A: Enclosures (Page Section: A) ....................................................................................................... 1 Collateral/Particular Standard Enclosures ................................................................................................................. 1 Particular Standard - (04) IEC61010_2_201B .......................................................................................................................................................2 Other Enclosures ..................................................................................................................................................... 32 Marking Label - (01) label .................................................................................................................................................................................... 33 Photographs - (01) 1 front.................................................................................................................................................................................... 34 Photographs - (02) 2 back ................................................................................................................................................................................... 35 Photographs - (03) 3 internal ............................................................................................................................................................................... 36 Photographs - (04) 4 PWBs top........................................................................................................................................................................... 37 Photographs - (05) 5 PWBs bottom..................................................................................................................................................................... 38 Photographs - (06) 6 Terminals ........................................................................................................................................................................... 39 Schematics + PWB - (01) Layout 0762-30xx ...................................................................................................................................................... 40 Schematics + PWB - (02) Layout 0762-31xx extension board ........................................................................................................................... 47 Schematics + PWB - (03) Schematic .................................................................................................................................................................. 54 UL CERTIFICATION DOCUMENTATION: .................................................................................................................... 1 APPENDIX B: UL Certification Documentation (Page Section: B).....................................................................1 Test Record ...........................................................................................................................................................2 APPENDIX C: Follow-Up Service Documentation (Page Section: C) ................................................................ 1 Follow-Up Service Procedure................................................................................................................................ 2 UL Authorization Page ..........................................................................................................................................3 UL Appendix:.........................................................................................................................................................7 GENERIC INSPECTION INSTRUCTIONS .............................................................................................................................................................7 INSTRUCTIONS AND DUTIES FOR UL REPRESENTATIVE ...............................................................................................................................8 INSTRUCTIONS FOR FOLLOW-UP TESTS AT UL ........................................................................................................................................... 15 RESPONSIBILITIES AND REQUIREMENTS FOR MANUFACTURER ............................................................................................................. 16 GENERAL TERMINOLOGY ................................................................................................................................................................................. 20 GENERAL PRODUCT CONSTRUCTION REQUIREMENTS ............................................................................................................................. 21 UL CERTIFICATION MARK ................................................................................................................................................................................. 30 Description .......................................................................................................................................................... 31 Markings and instructions ..................................................................................................................................................................................... 33 Special Instructions to UL Representative ........................................................................................................................................................... 33 Production-Line Testing Requirements ................................................................................................................................................................ 33 TABLE: List of Critical Components ..................................................................................................................................................................... 35 TEST RESULTS: ...........................................................................................................................................................1 APPENDIX D: Test Datasheets Enclosures (Page Section: D) ..........................................................................1 Datasheets - (01) DS1 ............................................................................................................................................................................................2 CERTIFICATE OF COMPLIANCE ................................................................................................................................ 1 Page iii Report No.: E175199-D1001-1/A0/C0-UL The following changes were made to this report. If none listed in the below table, this report is the originally issued report. The following scheme is used throughout this report to reflect the Report No.: (File No.) (Report Ref. No.) (x) / A(y) / C(z) (x) = Report (Re)Issue No. (y) = Amendment No. (z) = Correction No. YYY = Report Type (UL/CB/IEC) Date Modified (Year-Month-Day) YYY, where: Modifications Made (include Report Reference Number) Modified By Page 1 of 57 Report No.: E175199-D1001-1/A0/C0-UL Test Report issued under the responsibility of: TEST REPORT IEC 61010-1 Safety requirements for electrical equipment for measurement, control, and laboratory use Part 1: General requirements Report Reference No. .......................: E175199-D1001-1/A0/C0-UL Date of issue ..................................... : 2016-1-28 Total number of pages ......................: 57 Testing Laboratory ............................: Address .............................................: ..............................: Address .............................................: WAGO KONTAKTTECHNIK GMBH & CO KG HANSASTRASSE 27 MINDEN , 32423 DE Test specification: Standard ........................................... : IEC 61010-1:2010 (Third Edition) Test procedure..................................: UL Certification Non- N/A Test Report Form No. .......................: IEC61010_1J General disclaimer: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing UL testing laboratory. The authenticity of this Test Report and its contents can be verified by contacting UL. TRF No. IEC61010_1J Page 2 of 57 Test item description: Report No.: E175199-D1001-1/A0/C0-UL Programmable Controller Trade Mark: Manufacturer: Same as Applicant Model/Type reference: 0762-xxxx Ratings: 24V DC [-25%... +30%] Testing procedure and testing location: [] UL Testing Laboratory: Testing location/ address: [X] Tested by (name + signature): Erwin Fuchs Approved by (name + signature): Lee Berrecloth Testing procedure: WMT: Testing location/ address: ELREST AUTOMATIONSSYSTEME GMBHLEIBNIZSTR 10 KIRCHHEIM/TECK, 73230DE Germany Tested by (name + signature): Hans Gierlich Witnessed by (name + signature): Erwin Fuchs Approved by (name + signature): Lee Berrecloth TRF No. IEC61010_1J Page 3 of 57 Report No.: E175199-D1001-1/A0/C0-UL List of Attachments (including a total number of pages in each attachment): Refer to Appendix A of this report. All attachments are included within this report. Summary of testing Tests performed (name of test and test clause): Testing location: Refer to the Test List in Appendix D of this report if testing was performed as part of this evaluation. TRF No. IEC61010_1J Page 4 of 57 Report No.: E175199-D1001-1/A0/C0-UL Copy of marking plate The artwork below may be only a draft. The use of certification marks on a product must be authorized by the respective owners of these marks. Refer to the enclosure(s) titled Marking Plate in the Enclosures section in Appendix A of this report for a copy. TRF No. IEC61010_1J Page 5 of 57 Report No.: E175199-D1001-1/A0/C0-UL Test item particulars: Type of item: Control Description of equipment function: Human Machine Interface Connection to mains supply: Permanent connected to SELV Overvoltage category: II Pollution degree: 2 Means of protection: Class III (SELV) Environmental conditions: Extended (Specify): Surrounding Air Temperature: 0-60°C Mains Voltage fluctuations: -25%... +30% For use in wet locations: Yes Equipment mobility: Fixed Operating conditions: Continuous Overall size of equipment ( W x D x H) Max: App 293 x 223 x 58 mm Mass of equipment (kg): Max: 2,050 Marked degree of protection to IEC 60529: IP20 Testing Date of receipt of test item(s) ................................................. : 2015-10-19 Dates tests performed ............................................................ : 2015-10-19 Possible test case verdicts: - test case does not apply to the test object .......................... : N/A - test object does meet the requirement ................................. : Pass (P) - test object was not evaluated for the requirement ................. : N/E - test object does not meet the requirement ........................... : Fail (F) Abbreviations used in the report: - normal condition: N.C. - single fault condition: S.F.C. General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the issuing testing laboratory. "(see ENCLOSURE #)" refers to additional information appended to the report. "(see Form A.xx)" refers to a table appended to the report. Bottom lines for measurement tables Form A.xx are optional if used as record. Throughout this report a point is used as the decimal separator. The application for obtaining a UL Certification includes more than one factory location ............................................... : Yes When differences exist; they shall be identified in the General product information section. TRF No. IEC61010_1J Page 6 of 57 Name and address of factory (ies) ............................. : Report No.: E175199-D1001-1/A0/C0-UL Same as Applicant WAGO CORP N120 W19129 FREISTADT RD PO BOX 1015 GERMANTOWN, WI53022-8215US USA WAGO & CONTROLS (INDIA) LTD C-27 PHASE III GAUTAM BUDH NAGAR, SECTOR 58 NOIDA UP201301IN India WAGO ELECTRONIC (TIANJIN) CO LTD NO 5 QUANHUI RD WUQING DEVELOPMENT AREA 301700CN TIANJIN ELREST AUTOMATIONSSYSTEME GMBH LEIBNIZSTR 10 KIRCHHEIM/TECK, 73230DE Germany GENERAL PRODUCT INFORMATION: Report Summary All applicable tests according to the referenced standard(s) have been carried out. Refer to the Report Modifications page for any modifications made to this report. Product Description Human Machine Interface / Programmable Logic Controller 07620762anel HMI with Extended I/O 076207620762076207620762Model Differences N/A Additional Information N/A Technical Considerations The product was investigated to the following additional standards (from country differences): UL 61010-1, 3rd Edition, 2012-04-17 / CAN/CSA-C22.2 No. 61010-1, 3rd Edition, 2012-04 Additional: IEC 61010-2-201: 2013 (First Edition) TRF No. IEC61010_1J