Anti Condensation Heaters
Thermal Management Products
& Accessories from SAN
successfully used worldwide
for control panels and enclosures
for traffic control and monitoring systems in the transport
industry
for high voltage swichtgear in
outdoor and indoor substations
system protction in the automotive industry
in transmitter stations of cellular phone networks
for motor control centres and
control cabinets
2
Problem:
Condensation forms due to fluctuating temperature, even in sealed enclosures. In combination with dust and aggressive gases condensation causes
corrosion which results in stray currents and arcing. Too high a temperature,
or for that fact too low a temperature, can also lead to serious component
failure. The safety risk is enormous and the cost of operational delays as a
consequence is incalculable.
Solution:
Only constant optimum climatic
conditions allow components to function properly. The right climate can be
attained by a temperature and moisture control system. When temperatures are too low or when temperature differences (e.g. night / day) are large,
heating is required. It may also be necessary to keep components cool by
controlled ventilation.
Applications:
Whether for telecommunications or traffic systems, power
stations or outdoor plants, ATMs or parking control system, where electronics
have to be protected against humidity, heat or cold, SAN’s comprehensive
product range offers effective economical solutions.
Our Products:
Conventional and PTC semi-conductor control panel heaters and fan-assisted heaters ranging from 5W to 1200W, as well as tropicalised and EX variations. Temperature and humidity controls ranging from 0°C to 60°C (30° to
140°F) and 35% to 100% RH.
A new filter fan series in EMC and standard versions with excellent
performance and shielding
characteristics. Panel lighting and accessories.
About us:
We have been developing and producing innovative products for thermal
management for more than twenty years. Our products are renowned for their
reliability and long life, simplicity of use and high quality. Used and proven
worldwide even under extreme conditions.
Contents:
Heating:
Small semiconductor heater RCE 016 Series...................................................
4
Small semiconductor Heater RC 016 Series.....................................................
5
Small semiconductor Heater HGK 047 Series..................................................
6
Small semiconductor Heater CSK 060 Series..................................................
7
Finned extruded Heater SAN-FXE....................................................................8
Semiconductor Heater HG 140 Series..............................................................9
Compact Fan Heater HGL 046 Series...............................................................
10
Hazardous area Heaer CREx 020 Series...........................................................
11
Electrical Direct Heater SAN-LP........................................................................
12
Electrical Space Heater SAN-LP AF Ex Heater.................................................
13
Electrical Smart Heater SAN-SMLP..................................................................
14
Semiconductor Heater CS 060 Series..............................................................
15
Semiconductor Heater CSF 060 Series............................................................
16
Small semiconductor Fan Heater CS 028 Series..............................................
17
Compact semiconductor Fan Heater CSL 028 Series......................................
18
Electrical Smart Heater SAN-GSMLP...............................................................
19
Explosion proof Heater SP................................................................................
20
Electrical Smart Heater.....................................................................................
21
Electrical Smart-Space Ex Heater SM-*A.........................................................
22
Electrical Direct Ex Heater CS-*S......................................................................
23
Electrical Direct Ex Heater CT-*A......................................................................
24
Anti Condensation and Space Heater SAN-HEF..............................................
25
Space-saving Fan Heater HV 031 / HVL 031 Series.........................................
26
Semiconductor Fan Heater CR 027..................................................................
27
Fan Heater with integrated thermostat or hygrostat CR 030............................
28
Fan Heater with integrated thermostat or hygrostat CR 130............................
29
Fan Heater with/without integrated thermostat CS 030...................................
30
Fan Heater with/without integrated thermostat CS 130...................................
31
Ventilating:
Low maintenance Filter Fan FF 018 Series (21m3/to 102m3/h).........................
Low maintenance Filter Fan FF 018 Series (200m3/h).......................................
High-performance Filter Fan FF 018 Series (300m3/h)......................................
High-performance Filter Fan FF 018 Series (550m3/h)......................................
Outdoor Filter Fan FF 018 Series......................................................................
Low noise Roof Filter Fan RFF 018 Series........................................................
High-performance 19” Fan Tray LE 019 Series.................................................
32-33
34
35
36
37
38
39
Electronic Relay SM 010 (DC 24V + DC 48V)....................................................
Small, compact Thermostat KTO 011 / KTS 011..............................................
Fix Thermostat FTO 011 / FTS 011...................................................................
Dual Thermostat ZR 011...................................................................................
Dual Thermostat FTD 011.................................................................................
Mechanical Thermostat FZK 011......................................................................
Electronic Thermostat ET 011 (DC 24V)............................................................
Ex FixTherm96 Thermostat...............................................................................
FixTherm96 Thermostat....................................................................................
Mechanical Hygrostat MFR 012........................................................................
Electronic Hygrostat EFR 012...........................................................................
Electronic Hygrottherm ETF 012.......................................................................
Hazardous area Thermostat REx 011 Series....................................................
40
41
42
43
44
45
46
47
48
49
50
51
52
Slimline Lamp with on/off switch SL 025 Series...............................................
Slimline Lamp with movement sensor SL 025 Series.......................................
Dual Lamp with on/off switch DL 026 Series....................................................
Dual Lamp with movement sensor DL 026 Series............................................
Hand Lamp with lamp holder DL 026 Series....................................................
Compact Lamp KL 025 Series..........................................................................
53
54
55
56
57
58
Electrical Sockes SD 035 Series ....................................................................
Pressure compensation Device DA 084............................................................
Pressure compensation Device DA 284............................................................
Pressure compensation Device DA 284 (stainless steel)..................................
Self-adhesive appliance holder SANOFIX.........................................................
59
60
61
62
63
Calculation of temperature control in encloseures............................................
64
Regulating and monitoring:
Lighting:
Accessories:
Indication of measurements in m.m. Errors and omissions excepted. Specifications are subject to change without notice. Suitability of the products for their intended use and any associated risks must be determined by the
end customer/buyer in their final application.
3
5W, 9W
Small semiconductor
Heater - RCE 016 Series
•
•
•
•
•
Temperature limiting
Wide voltage range
Dynamic heating up
Energy saving
Compact
Small heaters designed to prevent condensation and to ensure a minimum
operating temperature in small enclosures.
Technical Data:
Operating voltage
12-240V AC/DC* (min. 110V, max. 265V)
Heating element
PTC resistor, temperature limiting
Heater body
Aluminum
Mounting
See Accessories
Fitting position
Variable
Dimensions
Length 45mm, Ø10mm
Op./storage temperature
-45 to +70ºC
Prot. type / Prot. class
IP32 / II (double insulated)
Approvals
VDE + UL File No. E150057
Accessories
Mounting clips (see illlustration)
Note
Other voltages on request
*) Op. with voltages below AC/DC 140V reduces heating performance by approx. 10%.
Example of connection
Thermostat KTO 011
(contact breaker, normally closed)
Heater RCE 016
Connection 2xAWG 22 sheathed cable (silicone)
L
N
Mounting clips Art. No. (1 packing unit = 2 pieces)
Art. No.
82240
120-240
Voltage
Heating capacity*
82241
12-36
5W
82242
120-240
9W
82243
12-36
10W
* At 20ºC (68˚F) ambient temperature.
4
5W
Inrush current max.
Surface temp. (approx.)
165˚C
2xAWG 22 sheathed cable (silicone)
Connection
Weight (approx.)
2.5A
175˚C
2xAWG 22 sheathed cable (silicone)
20g
2.0A
20g
8W, 10W, 13W
Small semiconductor
Heater - RC 016 Series
•
•
•
•
•
Temperature limiting
Wide voltage range
Dynamic heating up
Energy saving
Compact
These small heaters are designed to prevent condensation and to ensure a
minimum operating temperature in small enclosures.
Technical Data:
Operating voltage
120-24V AC/DC* -(min. 110V, max. 265V)
Heating element
PTC resistor, temperature limiting
Heater body
Aluminium, anodised
Mounting
Screw fixing
Fitting position
Variable
Op./storage temperature
-45 to +70ºC (-40 to +158˚F)
Prot. type / Prot. class
IP32 / II (double insulated)
Approvals
VDE + UL File No. E150057
Note
Other voltages on request
Art. No. : Connection 2xAWG 18 stranded wire
*Op. with voltages below 140V AC/DC reduces heating performance by approx.
10%.
Example of connection
Thermostat KTO 011
(contact breaker, normally closed)
Heater RC 016
Art. No. : Connection 2xAWG 22 sheathed cable (silicone)
Art. No. : Connection 2xAWG 22 sheathed cable (silicone)
L
N
Art. No.
Heating capacity*
Inrush current max.
Surface temp. (approx.)
150˚C
2xAWG 18 stranded wire
Connection
Weight (approx.)
82246
10W
2.5A
155˚C
2xAWG 22 sheathed cable (silicone)
28g
82248
13W
3.0A
170˚C
2xAWG 22 sheathed cable (silicone)
34g
82243
8W
3.7A
134˚C
2xAWG 18 stranded wire
20g
82244
8W
2.0A
20g
82247
10W
5.7A
132˚C
2xAWG 22 sheathed cable (silicone)
28g
82249
13W
10.0A
148˚C
2xAWG 22 sheathed cable (silicone)
34g
* At 20ºC (68˚F) ambient temperature.
5
10W to 30W
Small semiconductor
Heater - HGK 047 Series
•
•
•
•
•
Dynamic heating up
Energy saving
Wide voltage range
Temperature limiting
Clip fixing
The heaters are used in enclosures where condensation is to be prevented or
the temperature may not fall below a minimum value. In this way corrosion is
avoided and an even temperature is ensured.
Technical Data:
Heating element
PTC resistor, temperature limiting
Heater body
Extruded aluminium profile, anodised
Mounting
Clip for 35mm DIN rail, EN 60715
Fitting position
Vertical
Op. / Storage temp.
-45 to +70ºC
Prot. type / Prot. class
IP54 / I (earthed)
Accessories
Screw fixing
50
25
L
Clip for
35mm DIN rail
Example of connection
Heater HGK 047
300
12
Thermostat KTO 011
(contact breaker, normally closed)
L
N
Art. No.
Heating
capacity1)
Inrush
current max.
Length
(L)
Weight
(approx.)
10W
1.0A
50mm
Connection
Approval
83250
120-240V AC/DC2)
0.1kg
3 x 0.5mm2 x 300mm sheathed cable (silicone)
VDE
120-240V AC/DC2)
20W
2.5A
60mm
0.2kg
3 x 0.5mm2 x 300mm sheathed cable (silicone)
VDE
83252
83254
83251
120-240V AC/DC2)
30W
3.0A
70mm
0.2kg
3 x 0.5mm2 x 300mm sheathed cable (silicone)
VDE
83253
110-120V AC/DC
10W
1.0A
50mm
0.1kg
3 x AWG 20 x 300mm sheathed cable
UL File No. E150057
110-120V AC/DC
20W
1.5A
70mm
0.2kg
3 x AWG 20 x 300mm sheathed cable
UL File No. E150057
83255
110-120V AC/DC
30W
1.5A
100mm
0.2kg
3 x AWG 20 x 300mm sheathed cable
UL File No. E150057
1)
6
Operating voltage
at 20°C ambient temperature; 2) (min. 110V, max 265V) Operating with voltages below 140V AC/DC reduces heating performance by approx. 10%.
10W, 20W
Touch-Safe Small Semiconductor
Heater - CSK 060 Series
•
•
•
•
•
•
Low surface temperature
Double insulated (plastic housing)
Wide voltage range
Temperature limiting
Dynamic heating up
Clip fixing
The heaters are used in enclosures where condensation is to be prevented
or the temperature may not fall below a minimum value. In this way corrosion
is avoided and an even temperature is ensured. The heaters are designed for
permanent operation.
Technical Data:
Operating voltage
120-24V AC/DC* -(min. 110V, max. 265V)
Heating element
PTC resistor, temperature limiting
Surface temperature
<85ºC (according to VDE 0100) except upper protective grille
Connection
2-pole terminal 2.5mm2, torque 0.8Nm max.
Casing
Plastic according to UL94 V-0, black
Dimensions
98 x 38 x 75mm
Mounting
Clip for 35mm DIN rail, EN 60715
Fitting position
Vertical
Op./storage temp.
-45ºC to +70ºC
Prot. type / Prot. class
IP20 / II (couble insulated)
Approvals
VDE + UL File No. E150057 (according to UL499 in combination with
UL508A)
Note
Other voltages on request
*Op. with voltages below 140V AC/DC reduces heating performance by approx. 10%.
Example of connection
Thermostat FTO 011
(contact breaker, normally closed)
Art. No.
Heater CSK 060
Heating capacity*
Inrush current max.
Weight (approx.)
20W
2.5A
0.3kg
10W
1.0A
0.2kg
* At 20ºC (68˚F) ambient temperature.
7
Finned Extruded Enclosure Heater
Type SAN-FXE
The FXE range of heaters is designed specifically for frost protection, anti-condensation and temperature control within Zone 1 and Zone 2 Hazardous Areas. The FXE delivers a constant power output and comes complete with mounting bracket and a 1.5 metre flying lead.
Features
• Certified to meet the requirements of the ATEX Directive 94/9/EC, Gost
and IECEx.
• Compact design, requires minimal space.
• Optional over-temperature protection.
• Black anodized convective surface.
• Standard product available with short delivery times.
• Suitable for ambient temperatures -50°C up to +80°C.
Typical Applications:
Control / monitoring panels
Instrumentation cabinets
Condensation prevention
Temperature fluctuations
Frost protection
Motor enclosures
Certification
IECEx & ATEX certified Ex II 2 G/D, Ex d IIC (Gas) T3-T4 Gb, Ex t IIIC (Dust) T200-T135°C Db, EN/IEC60079-0 & EN/
IEC60079-1 & EN/IEC 60079-31
Extrusion
Finned Aluminium, Anodized Matt Black
Mounting:
Vertically Mounted by Bracket or Rail
Voltage:
Up to 254VAC
Rating:
Available in 30, 50, 75 & 100 Watts
Controls
If required, heaters can be supplied with a range of remote mounted thermostats.
Element:
18mm dia 321 St/Steel cartridge element with 1.5m silicone flex cable.
Weather protection:
IP6X
8
15W to 150W
Semiconductor
Heater - HG 140 Series
•
•
•
•
•
•
•
Pressure clamp connectors
Dynamic heating up
Wide voltage range
Temperature limiting
Energy saving
Clip fixing
Quick installation
These heaters are used in enclosures where damage from condensation
must be prevented, or where the temperature may not fall below a minimum
value. The aluminium profile heater body design has a chimney effect and
distributes the heat evenly. The pressure clamp connectors save time and
simplify installation.
Technical Data:
Operating voltage
120-240V AC/DC* (min. 110V, max. 265V)
Heating element
PTC resistor, temperature limiting
Heater body
Extruded aluminium profile, anodised
Connection
3 pressure clamps for stranded wire 0.5-1.5mm² (with wire end ferrule)
and rigid wire 0.5-2.5mm2
Connection casing
Plastic according to UL94 V-0, black
Mounting
Clip for 35mm DIN rail, EN 60715
Fitting position
Vertical
Op./storage temperature
-45 to +70ºC
Prot. type / Prot. class
IP20 / I (earthed)
Approvals
VDE + UL file E150057
Accessories
Screw fixing
*Op. with voltages below 140V AC/DC reduces heating performance by approx. 10%.
Art. No.
Heating capacity*
Inrush current max.
Length (L)
Weight (approx.)
83191
30W
3.0A
65mm
0.3kg
83192
45W
3.5A
65mm
0.3kg
83193
60W
2.5A
140mm
0.4kg
83194
75W
4.0A
140mm
0.5kg
83195
100W
4.5A
140mm
0.5kg
150W
9.0A
220mm
0.7kg
83190
83196
15W
1.5A
65mm
0.3kg
*At 20ºC (68˚F) ambient temperature.
9
Compact
Fan Heater - HGL 046 Series
•
•
•
•
•
Compact design
Temperature safety cut-out
Clip fixing
Long service life
Maintenance free
This compact fan heater prevents the formation of condensation. The integrated axial fan provides forced air circulation and so guarantees an even temperature in enclosures.
A built-in temperature safety cut-out switches the heater
off, in the event of fan failure.
Technical Data:
Operating voltage
AC 220-240V, 50-60Hz
AC 110-120V, 50-60Hz
Other voltages on request (e.g. AC/DC 48V)
Heating element
Resistance heater
Temp. safety cut-out
To protect against overheating in case of fan failure.
Heater body
Extruded aluminium profile, anodised
Surface temperature
Max 75°C (400W)
Axial fan
Ball bearing service life 50 000h at 25°C (77°F)
airflow 35m³/h, free flow
Connection
3-pole clamp for 2.5mm²
Mounting
Clip for 35mm DIN rail, EN 50022
Fitting position
Preferably vertical
Op./storage temperature
-40 to +70ºC (-40 to +158˚F)
Prot. type / Prot. class
IP20/I (earthed)
Approvals
VDE, UL file E150057
Art. No.
Approval
Operating voltage
Heating capacity*
Length (L)
Weight (approx.)
83257
VDE
AC 230V, 50-60Hz
400W
252mm
1.3kg
UL
AC 115V, 50-60Hz
250W
170mm
1.0kg
UL
AC 115V, 50-60Hz
400W
252mm
1.3kg
UL
AC 230V, 50-60Hz
250W
170mm
1.0kg
UL
AC 230V, 50-60Hz
400W
252mm
1.3kg
83256
83257-1
VDE
*At 20ºC (68˚F) ambient temperature.
10
AC 230V, 50-60Hz
250W
170mm
1.0kg
50W, 100W
Hazardous area
Heater - CREx 020 Series
•
•
•
•
Large convection surface
Clip fixing
Ready for use
Maintenance free
Compact convection heater for use in areas with explosion hazard for
prevention of formation of condensation, temperature fluctuations and for
protection against frost in transmitter housings, switch cabinets and measuring equipment.
Technical Data:
Explosion protection acc. to EN
LCIE (Laboratoire Central des Industries Electriques)
Conformity certificate
01 ATEX 6073/03, LCIE No 06 ATEX Q8011, IECEx LCI 07, 0020
Heating element
High performance cartridge
Heater body
Aluminium profile, black anodised
Connection
Si HF-JZ 3 x 0.75mm2 cable, length 1m
Connection PE
4mm2
Mounting
Clip for 35mm DIN rail, EN 60715
Fitting position
Vertical
Operating/storage temperature
-20 to +40ºC / -45 to 70ºC
Protection type /Protection class
IP65 / I (earthed)
Clip can alternatively
be fixed on long side
Hazardous area Thermostat REx 011
see page 40
Art. No.
Operating voltage
Heating capacity*
Ex protection type
d IIC T5 - Ex tD A21 IP6X T100˚C
Surface temperature
Length (L)
83198
230-240VAC
50W
100W
d IIC T4 - Ex tD A21 IP6X T135˚C
135˚C
180mm
1.5kg
50W
d IIC T5 - Ex tD A21 IP6X T100˚C
100˚C
150mm
1.3kg
100W
d IIC T4 - Ex tD A21 IP6X T135˚C
135˚C
180mm
1.5kg
83197
230-240VAC
110-120VAC
110-120VAC
100˚C
150mm
Weight (approx.)
1.3kg
11
Electrical Direct Heater
SAN-LP Heater
Direct-heaters for Hazardous locations, designed for direct
mounting onto e.g. manifolds etc.
• Freeze protection
• Anti-condensation
• Temperature maintenance
Features and Advantages
•
•
•
•
•
•
Certified to meet the requirements of the ATEX Directive 94/9/EC, Gost and IECEx.
Self-limiting heating elements
Small dimensions
No moving parts, no maintenance required therefore long lifetime
Suitable for T4 and T3 classifications
Can be used for 110 / 240 VAC/DC
Description
All Cameo Heaters are designed around self-limiting heating elements. These self-limiting semi-conductor elements
are saving power consumption. Our Cameo Direct-heaters are designed to heat the installed equipment. If properly
selected for freeze protection, no thermostat will be needed.
Optional body #5 : 4 holes diam. 5,2 mm. available in
Aluminium and SS range
For easy mounting, at no extra charge
Alternative 316 Stainless Steel heaters can be delivered for the 100-10 Watt range.
Also possible is an aluminium body with four holes drilled through (body #5), for easy mounting.
Please see below for further technical data.
Range
LP-1A
LP-2A
LP-3A
LP-4A
T3
T4
T4
T4
ca. 115 °C Surface temperature
ca. 105 °C Surface temperature
ca. 90 °C Surface temperature
ca. 70 °C Surface temperature
100-10 Watt
100-10 Watt
100-10 Watt
100-10 Watt
High Power model:
LP0AHP
T3
ca. 130 °C Surface temperature 200-20 Watt
* these temperatures are measured at 20 °C ambient temperature.
12
Electrical Space Heater
SAN-LP AF Ex Heater
Space-heaters for Hazardous locations, designed for :
• Freeze protection
• Anti-condensation
• Temperature maintenance
Technical Data:
Power consumption
100-10 Watt
Electrical cable
3x1 sqmm
Material cable
braided silicone, optional: non-braided cable
Standard length
approx. 1 mtr. Other lengths optional
Other lengths
To be specified
Overall dimensions
164x100x60mm (LxWxH)
Material
black anodized aluminium
EX protection class
II 2G Ex d IIC T4 or T3: II 2D Ex tD A21 IP66 T 135°C or T200°C
Certification
KEMA 01ATEX2124X and IECEx DEK 11.0017
Protection degree
IP66
Voltage
110/240
Ambient temp. range
-60°C...+90°C
Features and Advantages
Range
•
•
•
LP-1AF
LP-2AF
LP-3AF
LP-4AF
•
•
Self-limiting heating elements
Small dimensions
No moving parts, no maintenance required therefore
long lifetime
Suitable for T4 and T3 classifications
Can be used for 110 / 240 VAC/DC
T3
T4
T4
T4
ca. 115 °C Surface temperature
ca. 105 °C Surface temperature
ca. 90 °C Surface temperature
ca. 70 °C Surface temperature
100-10 Watt
100-10 Watt
100-10 Watt
100-10 Watt
* these temperatures are measured at 20 °C ambient temperature.
Description
All Cameo Heaters are designed around self-limiting heating elements. These semi-conductor elements are saving
power consumption. Our Cameo Space-heaters heat the air
inside an enclosure and indirectly the installed equipment. If
properly selected for freeze protection, no thermostat will be
needed.
In other situations, if the equipment, e.g. analyzers, it is normal practice to use our Space-Heters in combination with
our Fix-Therm96 thermostats (range from 10°C up to 135°C)
Do not cover the fins to guarantee free convection.
13
Electrical Smart Heater for Space Heating
SAN-SMLP Ex Heater
Space-heaters for Hazardous locations, this compact
model is designed for
• Anticondensation
• Freeze protection
• Temperature maintenance
• Small spaces
Features and Advantages
• Certified to meet the requirements of the ATEX Directive 94/9/EC, Gost and IECEx.
• Self-limiting heating elements
• Small dimensions
• No moving parts, no maintenance required therefore long lifetime
• Suitable for T4 and T3 classifications
• Can be used for 110 / 240 VAC/DC
Description
All SMART Space-heaters are designed around self-limiting heating elements. These semi-conductor elements are
saving power consumption.
Our SMART Space-heaters are designed to heat the air inside an enclosure and indirectly the installed equipment. If
properly selected for freeze protection, no thermostat will be needed.
In other situations, if the equipment may not exceed a maximum temperature value, you can add our Fix-Therm96
thermostat as a maximum temperature protection, in the system.
When required in other applications, e.g. analyzers, it is normal practice to use our SMART Space-heaters in combination with our FixTherm96 thermostats (range from 10°C up to 135°C).
Do not cover the fins to guarantee free convection..
Range
SMLP-1A
SMLP-2A
SMLP-3A
SMLP-4A
T3 ca. 115°C Surface temperature
T4 ca. 105°C Surface temperature
T4 ca. 90°C Surface temperature
T4 ca. 70°C Surface temperature
100-10 Watt
100-10 Watt
100-10 Watt
100-10 Watt
High power model:
SMLP0AHP T3 ca. 130°C Surface temperature 200-20 Watt
* these temperatures are measured at 20 °C ambient temperature.
14
50W to 150W
Touch-Safe Semiconductor
Heater - CS 060 Series
•
•
•
•
•
Low surface temperature
Quick mounting due to clip fixing
Double insulated (plastic)
Wide voltage range
Small size
Touch-safe heater for the use in enclosures with electrical/electronical components. The design of the heater supports the natural convection which
results in a high air-current of warm air. The surface temperatures on the accessible side surfaces of the housing are kept down as a result of the heater
design. Our complete range of thermostats and hygrostats can directly be
connected to the heater CS 060. This heater is also available in a version
with plug-in thermostat requiring no additional wiring (C*SF 060). Both versions are designed for permanent operation.
Technical Data:
Operating voltage
120-240V AC/DC* (min. 110V, max. 265V)
Heating element
PTC resistor, temperature limiting
Surface temperature
<80ºC, except upper protective grille
Connection
4-pole terminal 2,5mm2, torque 0.8Nm max.
Casing
Plastic according to UL94 V-0, black
Mounting
Clip for 35mm DIN rail, EN 60715
Fitting position
Vertical
Op./storage temperature
-45 to +70ºC
Prot. type / Prot. class
IP20 / II (double insulated)
Approvals
VDE + UL file E150057 (according to UL499
in combination with UL508A)
Note
Other voltages on request
*Op. with voltages below 140V AC/DC reduces heating performance by approx. 10%.
Heater CS 060
Heater CS 060
Thermostat
FTO 011
Leistungs-Umgebungstemperatur-Diagramm
Heating
capacity / Ambient temperature diagram CS 060
Heating
capacity
(W)
Heizleistung
(W)
CS 160
AC
200
178
160
147
150
Heater CS 060
132
122
119
Art. Nr. 16000.0-00
110
102
100
Thermostat
FTO 011
93
85
66
61
50
50
0
-40
-20
Art. Nr. 16010.0-00
55
0
20
44
Art. Nr. 16020.0-00
40
Umgebungstemperatur
Temperature (ºC) (°C)
AC
Examples of connection
Art. No.
1)
Heating capacity1)
Inrush current max.
Air outlet temp.2)
+86ºC
110 x 60 x 90mm
Dimensions
Weight (approx.)
100W
4.5A
+120ºC
110 x 60 x 90mm
0.3kg
150W
8A
+145ºC
150 x 60 x 90mm
0.5kg
50W
2.5A
0.3kg
Ambient temperature - see Heating capacity / Ambient temperature diagram; 2)measured 50mm above protective grille.
15
50 W to 150W
Touch-Safe Semiconductor
Heater - CSF 060 Series
•
•
•
•
•
•
Low surface temperature
Integrated thermostat
Quick mounting due to clip fixing
Double insulated (plastic)
Wide voltage range
Small size
Touch-safe heater for the use in enclosures with electrica/electronical components. The design of the heater supports the natural convection which
results in a high air-current of warm air. The surface temperatures on the accessible side surfaces of the housing are kept down as a reslt of the heater
design. This model with plug-in thermostat does not require additional
wiring. The heaters are designed for the permanent operation. This heater is
also available in a version without thermostat (CS 060).
Technical Data:
120-240VAC* (min. 110V, max. 265V)
Heating element
PTC resistor, temperature limiting
Surface temperature
<80ºC, except upper protective grille
60
Operating voltage
Connection
4-pole terminal 2.5mm2, torque 0.8Nm max.
Casing
Plastic according to UL94 V-0, black
Mounting
Clip for 35mm DIN rail, EN 60715
Fitting position
Vertical
Op./storage temp.
-20 to +70ºC / -45 to +70ºC
Prot. type / Prot. class
IP20 / II (double insulated)
Approvals
VDE + UL File No. E150057 (acc. to UL499 in combination with UL508A)
Note
Other voltages on request
L
90
23
*Op. with voltages below 140VAC reduces heating performance by approx. 10%
Leistungs-Umgebungstemperatur-Diagramm
Heater CSF 060
CS temperature
160
Heating capacity / Ambient
diagram CSF 060
200
Heizleistung (W)
Heating capacity (W)
178
Example of connection
160
147
150
132
122
119
Art. Nr. 16000.0-00
110
102
100
93
85
66
61
50
50
0
-40
Art. Nr. 16010.0-00
55
-20
0
20
44
Art. Nr. 16020.0-00
40
Umgebungstemperatur (°C)
Temperature (ºC)
Art. No.
Heating
capacity*
Inrush current
max.
Air outlet
temperature2)
Switch-off
temperature3)
Starting
temperature3)
50W
2.5A
+86ºC
+25ºC
4.5A
+120ºC
+15ºC
4.5A
+120ºC
8A
8A
50W
100W
100W
150W
150W
2.5A
Dimensions
Weight (approx.)
+5ºC
110 x 60 x 90mm
0.3kg
+15ºC
110 x 60 x 90mm
0.3kg
+5ºC
110 x 60 x 90mm
0.3kg
+25ºC
+15ºC
110 x 60 x 90mm
0.3kg
+145ºC
+15ºC
+5ºC
150 x 60 x 90mm
0.5kg
+145ºC
+25ºC
+15ºC
150 x 60 x 90mm
0.5kg
+86ºC
+15ºC
ambient temperature - see Heating capacity / Ambient temperature diagram; 2)measured 50mm above protective grille; 3)tolerance of ±5K.
1)
16
150W
Small Semiconductor
95
Fan Heater - CS 028
•
•
•
•
Small, compact design
Quite in operation
Dynamic heating up
Clip or screw fixing
32
90
75
95
Fan heater prevents formation of condensation and provides an evenly distributed interior air temperature in enclosures with electric/electronic components. The heater is connected using the internal terminal connectors. The
CS 028’s small size make it ideal for use in enclosures where space is at a
premium.
75
Technical Data:
32
65
90
Heating element
PTC heating element
Inrush current
max. 12A at 230VAC, 6A at 120VAC
Surface temperature
max. 50ºC at casing; 100ºC at upper protective grille
at 20ºC ambient temperature.
Axial fan, ball bearing
Air flow 13.8m3/h, free flow (service life 40,000h at 40ºC)
Connection
2-pole clamp max. 2.5mm , clamping screw torque 0.8Nm max.
Casing
Plastic according to UL94-0, black
Mounting
Clip for 35mm DIN rail, EN 60715 or screw fixing (Ø5.3mm)
Fitting position
Vertical
Weight
Approx. 0.3kg
Op./storage temp.
-45 to +70ºC
Prot. type / Prot. class
IP20 / II (double insulated)
Note
Other voltages on request.
65
90
2
Heating capacity / Ambient temperature diagram CSF 060
75
View: back side
Screw fixing
65
95
90
Temperature (ºC)
75
Heating capacity (W)
Clip fixing
32
Example of connection
FAN Heater CS 028
Thermostat KTO 011
(contact breaker, normally closed)
30
20
10
40
50
60
3 4
75
95
0
L
32
Art. No.
Operating voltage
230VAC, 50/60Hz
N
Heating capacity*
150W
87 x 65 x 75mm
Dimensions
Mounting
Clip fixing
VDE; (UL submitted)
Approvals
VDE, (UL submitted)
230VAC, 50/60Hz
150W
87 x 65 x 114mm
Screw fixing
120VAC, 50/60Hz
150W
87 x 65 x 75mm
Clip fixing
UL submitted
120VAC, 50/60Hz
150W
87 x 65 x 114mm
Screw fixing
UL submitted
*at 20ºC ambient temperature.
17
250W, 400W
Compact Semiconductor
Fan Heater - CSL 028
•
•
•
•
Small, compact design
Quiet in operation
Dynamic heating up
Clip or screw fixing
Fan heater prevents formation of condensation and provides an evenly distributed interior air temperature in enclosures with electric/electronic components. The heater is connected using the internal terminal connectors. The
small size of the CSL 028 makes it ideal for use in enclosures where space is
at a premium.
Technical Data:
Heating element
PTC heating element
Surface temperature
250W: max 50ºC, except upper protective grille
400W: max 65ºC, except upper protective grille
at 20ºC ambient temperature
Axial fan, ball bearing
Air flow 45m3/h at 230VAC, air flow 54m3/h at 120VAC
free flow, service life 40,000h at 40ºC
Connection
2-pole clamp max. 2.5mm2 with strain relief,
clamping torque 0.8Nm max.
Casing
Plastic acc. to UL94-0, black
Mounting
Clip for 35mm DIN rail, EN 60715 or screw fixing (Ø5.3mm)
Fitting position
Vertical
Weight
Approx. 0.5kg
Op./storage temp.
-45 to +70ºC
Prot. type / Prot. class
IP20 / II (double insulated)
Note
Other voltages on request
View: back side
Screw fixing
Clip fixing
Heating capacity (W)
Heating capacity / Ambient temperature diagram CSF 060
Example of connection
Thermostat KTO 011
FAN Heater CSL 028
(contact breaker, normally closed)
Temperature (ºC)
Art. No.
83710
83711
Operating voltage
230VAC, 50/60Hx
230VAC, 50/60Hz
120VAC, 50/60Hz
120VAC, 50/60Hz
83715
83716
230VAC, 50/60Hz
230VAC, 50/60Hz
120VAC, 50/60Hz
120VAC, 50/60Hz
*at 20ºC ambient temperature
18
Heating capacity*
Inrush current max.
Dimensions
111x85x90mm
Mounting
250W
9A
Clip fixing
VDE; (UL submitted)
9A
111x85x129mm
Screw fixing
VDE; (UL submitted)
6A
111x85x90mm
Clip fixing
UL submitted
6A
111x85x129mm
Screw fixing
UL submitted
15A
111x85x90mm
Clip fixing
VDE; (UL submitted)
15A
111x85x129mm
Screw fixing
VDE; (UL submitted)
9A
111x85x90mm
Clip fixing
UL submitted
9A
111x85x129mm
Screw fixing
UL submitted
250W
250W
250W
400W
400W
400W
400W
Approvals
Electrical Smart Space-Heater, General purpose
SAN-GSMLP Heater
Space-heaters for Non-Hazardous locations are designed for
• Anticondensation
• Freeze protection
• Temperature maintenance
Features and Advantages
• Self-limiting heating elements
• Small dimensions
• No maintenance required, no moving parts: long lifetime
• Can be used for 110 / 240 VAC/DC
Technical Data:
Power consumption
200-20 Watt
Electrical cable
3x1 sqmm
Material cable
non-braided silicone cable
Standard length
approx. 1 mtr. Other lengths optional
Other lengths
To be specified
Overall dimensions
100x54x54mm (LxWxH)
Weight
Approx. 1400g
Material
black anodized aluminium
Protection degree
IP66
Voltage
110/240
High power model:
GSMLP0AHP T3ca.130°C Surface temperature
200-20 Watt
* these temperatures are measured at 20 °C ambient temperature.
Description
All SMART Space-heaters are designed around self-limiting heating elements. These semi-conductor elements are
saving power consumption.
Our SMART Space-heaters are designed to heat the air inside an enclosure and indirectly the installed equipment. If
properly selected for freeze protection, no thermostat will be needed.
In other situations, if the equipment may not exceed a maximum temperature value, you can add our Fix-Therm96
thermostat as a maximum temperature protection, in the system.
When required in other applications, e.g. analyzers, it is normal practice to use our SMART Space-heaters in combination with our FixTherm96 thermostats (range from 10°C up to 135°C).
Do not cover the fins to guarantee free convection..
19
Explosion proof
Anti Condensation Heater - SP
Space-heaters for Hazardous locations are designed for
• Freeze protection
• Anti-condensation
• Temperature maintenance
Features and Advantages
• Self-limiting heating elements
• Small dimensions
• No maintenance required, no moving parts: long lifetime
• Suitable for T4 and T3 classifications
• Can be used for 110 / 240 VAC/DC
Description
Technical Data:
Power consumption
250-25Watt or 500-50Watt
Electrical cable
3x1 sqmm
Material cable
Braided silicone (standard) non-braided optional
Standard length
approx. 1 mtr. Other lengths optional, on request
Other lengths
To be specified
Overall dimensions
165x185x41,6mm (LxWxH)
Weight
Approx. 1600g
Material
black anodized aluminium
EX protection class
II2G Ex d IIC T4 or T3: II2D Ex tD A21 IP66 T135ºC or T200ºC
Certification
KEMA 01ATEX2124X and IECEx DEK 11.0017
Protection degree
IP66
Voltage
110/240 VAC/DC
Ambient temp. range
-60ºC...+90ºC
All SP Heaters are designed around self-limiting heating
elements. These semi-conductor elements are saving power
consumption.
Our SP Space-Heaters are designed to heat the air inside an
enclosure and indirectly the installed equipment.
If properly selected for freeze protection, no thermostat will be
needed.
When required in other appications, e.g. analyzers, it is normal
to use our space heaters in combination with our Fix-Therm96
termostats (range from 10°C up to 135°C).
Do not cover the fins to guarantee free convection.
Surface temp.
Wattage
SP-1A
Part No.
Temp. class
T3
Approx 115ºC
250-25
SP-2A
T4
Approx 105ºC
250-25
SP-3A
T4
Approx. 90ºC
250-25
SP-4A
T4
Approx. 70ºC
250-25
T3
Approx. 130ºC
500-50
High power model
SP-0AHP
*these temperatures are measured at 20ºC ambient temperature.
20
Electrical Smart-Space Heater
Type GSM-*A
Space-heaters for Non-Hazardous locations, designed
for
• Freeze protection
• Anti-condensation
• Temperature maintenance
Features and Advantages
• Self-limiting heating elements
• Small dimensions
• No moving parts, no maintenance required therefore long lifetime
• Can be used for 110 / 240 VAC/DC
Technical Data:
Power consumption
250-25Watt or 500-50Watt
Electrical cable
3x1 sqmm
Material cable
Non-braided silicone cable
Standard length
approx. 1 mtr. Other lengths optional, on request
Other lengths
To be specified
Overall dimensions
164x54x54mm (LxWxH)
Weight
Approx. 1400g
Material
black anodized aluminium
Voltage AC/DC
110/240
Protection class
IP66
Description
All Smart Space-Heaters are designed around self-limiting heating elements. These semi-conductor elements are
saving power consumption.
Our Smart Space-Heaters are designed to heat the air inside an enclosure and indirectly the installed equipment. If
properly selected for freeze protection, no thermostat will be needed.
When required in other applications, e.g. analyzers, it is normal practice to use our Smart Space-Heaters in combinations with our FixTherm96 (range from 10°C up to 130°C).
Part No.
Smart GSM-1A
Smart GSM-2A
Smart GSM-3A
Smart GSM-4A
High power model
Surface temp.
Wattage
Approx 105ºC
250-25
Approx 115ºC
Approx. 90ºC
Approx. 70ºC
250-25
250-25
250-25
Smart GSM-0AHP
Approx. 130ºC
500-50
*these temperatures are measured at 20ºC ambient temperature.
21
Electrical Smart-Space Ex Heater
Type SM-*A
Space-heaters for Hazardous locations, designed for
• Freeze protection
• Anti-condensation
• Temperature maintenance
• Small spaces
Features and Advantages
• Self-limiting heating elements
• Small dimensions
• No moving parts, no maintenance required therefore long lifetime
• Suitable for T4 and T3 classification
• Can be used for 110 to 240 VAC/DC
Technical Data:
Power consumption
250-25Watt or 500-50Watt
Electrical cable
3x1 sqmm
Material cable
Braided silicone (standard) Non-braided optional
Standard length
approx. 1 mtr. Other lengths optional, on request
Other lengths
To be specified
Overall dimensions
164x54x54mm (LxWxH)
Weight
Approx. 400g
Material
black anodized aluminium
EX protection class
II 2G Ex d IIC T4 or T3: II 2D Ex tD A21 IP66 T 135°C or T200°C
Certification
KEMA 01ATEX2124X and IECEx DEK 11.0017
Voltage AC/DC
110/240 VAC/DC
Protection degree
IP66
Ambient temp. range
-60°C...+90°C
Description
All Smart Space-Heaters are designed around self-limiting heating elements. These semi-conductor elements are
saving power consumption.
Our Smart Space-Heaters are designed to heat the air inside an enclosure and indirectly the installed equipment. If
properly selected for freeze protection, no thermostat will be needed.
In other situations, if the equipment may not exceed a maximum temperature value, our Fix-Therm96 thermostat can
be added as a maximum temperature protection, in the system.
When required in other applications, e.g. analyzers, it is normal practice to use our Smart Space-Heaters in combinations with our FixTherm96 (range from 10°C up to 135°C).
Part No.
Smart SM-1A
Smart SM-2A
Smart SM-3A
Smart SM-4A
High power model
Smart SM-0AHP
Surface temp.
Wattage
Approx 105ºC
250-25
Approx 115ºC
Approx. 90ºC
Approx. 70ºC
Approx. 130ºC
*these temperatures are measured at 20°C ambient temperature.
22
250-25
250-25
250-25
500-50
Electrical Direct Ex Heater
Type CS-*S
Space-heaters for Hazardous locations, designed for
direct mounting onto e.g. manifolds etc.
• Freeze protection
• Anti-condensation
• Temperature maintenance
Features and Advantages
• Self-limiting heating elements
• Small dimensions
• No moving parts, no maintenance required therefore long lifetime
• Suitable for T4 and T3 classification
• Can be used for 110 to 240 VAC/DC
Technical Data:
Power consumption
250-25Watt
Electrical cable
3x1 sqmm
Material cable
Braided silicone; optional: Non-braided optional
Standard length
approx. 1 mtr. Other lengths optional
Other lengths
To be specified
Overall dimensions
85x65x28mm (LxWxH)
Weight
Approx. 900g
Material
stainless steel 316
EX protection class
II 2G Ex d IIC T4 or T3: II 2D Ex tD A21 IP66 T 135°C or T200°C
Certification
KEMA 01ATEX2124X and IECEx DEK 11.0017
Voltage AC/DC
110/240 VAC/DC
Protection degree
IP66
Ambient temp. range
-60°C...+90°C
Description
All Cameo Heaters are designed around self-limiting heating elements. These semi-conductor elements are saving
power consumption.
Our Cameo Direct Heaters are designed to heat the installed equipment. If properly selected for freeze protection, no
thermostat will be needed.
Part No.
CS-1S
CS-2S
CS-3S
CS-4S
Classification
T3
T4
T4
T4
Surface temp.
Wattage
Approx 105ºC
250-25
Approx 115ºC
Approx. 90ºC
Approx. 70ºC
250-25
250-25
250-25
*these temperatures are measured at 20°C ambient temperature.
23
Electrical Direct Ex Heater
Type CT-*A
Direct heaters for Hazardous locations, designed for
• Freeze protection
• Anti-condensation
• Temperature maintenance
Features and Advantages
• Self-limiting heating elements
• Small dimensions
• No moving parts, no maintenance required therefore long lifetime
• Suitable for T4 and T3 classification
• Can be used for 110 to 240 VAC/DC
Technical Data:
Power consumption
250-25Watt
Electrical cable
3x1 sqmm
Material cable
Braided silicone; optional: Non-braided optional
Standard length
approx. 1 mtr. Other lengths optional
Other lengths
To be specified
Overall dimensions
88x70x35mm (LxWxH)
Weight
Approx. 550g
Material
black anodized aluminium
EX protection class
II 2G Ex d IIC T4 or T3: II 2D Ex tD A21 IP66 T 135°C or T200°C
Certification
KEMA 01ATEX2124X and IECEx DEK 11.0017
Voltage AC/DC
110/240 VAC/DC
Protection degree
IP66
Ambient temp. range
-60°C...+90°C
Description
All Cameo Heaters are designed around self-limiting heating elements. These semi-conductor elements are saving
power consumption.
Our Cameo Direct Heaters are designed to heat the installed equipment. If properly selected for freeze protection, no
thermostat will be needed.
Part No.
CT-1A
CT-2A
CT-3A
CT-4A
Classification
T3
T4
T4
T4
Surface temp.
Wattage
Approx 105ºC
250-25
Approx 115ºC
Approx. 90ºC
Approx. 70ºC
*these temperatures are measured at 20°C ambient temperature.
24
250-25
250-25
250-25
Anti Condensation & Space Heater
Type SAN-HEF Hazardous Area
The self-regulating properties of the HEF enclosure heaters eliminate the requirement for a thermostat. Coupled
with the compact design, this makes the HEF ideal for anti
condensation, frost protection and temperature control
where the enclosure is located within Zone 1 and Zone 2
Hazardous Areas.
Certified to ATEX Directive 94/9/EC IECEx, they are suitable
for use where the flammable atmosphere is Group IIA, IIB or
IIC Gas.
Features
• Certified to meet the requirements of the ATEX Directive 94/9/EC, Gost and IECEx.
• Compact, low profile, stainless steel case, requires minimal space.
• Self-regulating - can be used without a thermostat.
• Suitable for ambient temperatures from -60° to +80°C.
• Mounting of the heater can be in any orientation.
• Design allows installation close to internal components and cables without fear of damage by overheating.
Typical Applications:
Control / monitoring panels
Instrumentation cabinets
Condensation prevention
Temperature fluctuations
Frost protection
Certification
ATEX certified Ex II 2 G
IECEx & ATEX certified Ex’e’ T4
EN/IEC60079-0 & EN/IEC60079-7
Casing
Perforated stainless steel
Element
Self-regulating
Controls
The HEF is self-regulating, automatically reducing its output as the ambient temperature rises if overall enclosure
temperature control is required it is recommended that the HEF heater is used in conjunction with one of the Ex’d’
thermostats.
Mounting
The heater may be mounted in any orientation, using appropriate securing bolts through the mounting feet.
Rating
The HEF range is available in a nominal 30, 50, 100, 200 & 500 Watt outputs, models available for 110V or 230-240V
single phase supplies.
25
100W to 400W
Space-saving
Fan Heater HV/HVL 031 Series
•
•
•
•
•
Compact
Flat design
High air flow
Temperature safety cut-out
Clip fixing
The compact high-performance fan heater prevents formation of condensation in control or switch
systems and provides an evenly distributed
interior air temperature in enclosures. This fan heater is available without fan
(HV 031) as well as with fan (HVL 031).
Technical Data:
HV 031
Heater without fan (fan mounting kit included)
HVL 031
Heater with fan
Heating element
High performance cartridge
Temp. safety cut-out
To protect against overheating in case of fan failure
Heater body
Die-cast aluminium (glass bead blasted)
Connection
3-pole screw connector 2.5mm², clamping torque 0.8Nm max.
Connection casing
Plastic acc. to UL94 V-0, black
Mounting
Clip for 35mm DIN rail, EN 60715
Fitting position
Horizontal
Op./storage temp.
-45 to +70ºC
Prot. type / Prot. class
IP20/I (earthed)
Approvals
UL file E187294 (230V only: VDE)
HVL 031 only:
Axial fan, ball bearing
Airflow see table
Service life 50,000h at 25°C
Connection (axial fan)
2-pole screw connector 2.5mm2 (L2/N2)
a.) Clip
b.) Type plate
c.) Axial fan
d.) Air direction
Important! Heater may only be
operated together with fan.
Danger of overheating!
Art. No. HV 031
230VAC, 50/60Hz
83275
Art. No. HV 031
120VAC, 50/60Hz
Heating capacity
83276
83277
83278
83279
Art. No. HVL 031
230VAC, 50/60Hz
Weight (approx.)
100W
80x112 22mm
0.4kg
150W
80x112x22mm
0.4kg
200W
119x151x22mm
0.5kg
300W
119x151x22mm
0.5kg
400W
119x151x22mm
0.5kg
Dimension
Weight (Approx.)
100W
Airflow min.,
free flow
35m3/h
80x112x47mm
0.6kg
83179
150W
35m3/h
80x112x47mm
0.6kg
83180
200W
108m3/h
119x151x47mm
0.9kg
83181
300W
108m3/h
119x151x47mm
0.9kg
83182
400W
108m3/h
119x151x47mm
0.9kg
83178
26
Art. No. HVL 031
120VAC, 50/60Hz
Dimensions
Heating capacity
up to 650W
Semiconductor
Fan Heater - CR 027 Series
•
•
•
•
•
•
Compact heater
Heating capacity adjusts to ambient temperature
Adjustable temperature range
Clip fixing
Optical indicator
Temperature safety cut-out
Semiconductor fan heaters prevent the formation of condensation and
ensure an even temperature in switch and control equipment. The built-in
regulator is used to set the desired temperature.
Technical Data:
Heating element
PTC resistor, temperature limiting
Temp. safety cut-out
To protect against overheating in case of fan failure
Axial fan, ball bearing
Airflow see table
service life 50,000h at 25°C
Connection
2-pole clamp 2.5mm2, clamping torque 0.8Nm max.
Casing
Plastic, according to UL94 V-0, light grey
Optical indicator
Thermostat control lamp
Mounting
Clip for 35mm DIN rail, EN 60715
Fitting position
Vertical
Op./storage position
-45 to +70ºC
Dimensions
100 x 128 x 165mm
Prot. type / Prot. class
IP20 / II (double insulated)
Approvals
UL file E204590
Heating capacity (W)
Heating capacity / Ambient temperature
diagram CR 027 (60Hz)
Heating capacity (W)
Heating capacity / Ambient temperature
diagram CR 027 (50Hz)
Temperature (ºC)
Art. No.
Temperature (ºC)
Operating
voltage
Heating capacity*
(50Hz)
Heating capacity*
(60Hz)
Inrush
current max.
Airflow,
free flow
83286
220-240VAC, 50/60Hz
550W
650W
13.0A
45m3/h
83288
100-120VAC, 50/60Hz
510W
650W
15.0A
45m3/h
83285
83287
220-240VAC, 50/60Hz
100-120VAC, 50/60Hz
* At 20ºC (68˚F) ambient temperature.
475W
400W
550W
550W
11.0A
14.0A
Setting range
Temp. regulator
Weight
(approx)
35m3/h
0 to +60°C
0.9kg
35m3/h
+32 to +140°F
0.9kg
0 to +60ºC
+32 to +140ºF
1.1kg
1.1kg
27
950W
Compact high-performance
Fan Heater - CR 030
•
•
•
Compact design
Double insulated
Integrated thermostat or hygrostat
The compact high performance fan heater prevents formation of condensation and provides an evenly distributed interior air temperature in enclosures
with electric/electronic components. The plastic enclosure provides double
insulation and acts as protection against contact. The fan heater is available
with integrated thermostat or pre-set hygrostat for temperature or humidity
control. The CR 030 was designed as a stationary unit for the bottom of the
enclosure. For wall fixing the fan heater CR 130 is recommended.
Technical Data:
Heating element
High performance cartridge
Temp. safety cut-out
to protect against overheating in case of fan failure,
automatic reset
Heater body
extruded aluminium profile
Axial fan, ball bearing
Airflow 160m3/h, free flow
service life 50,000h at 25°C
Connection
2-pole clamp max. 2.5mm2, clamping screw with strain relief, torque
0.8Nm max.
Casing
Plastic according to UL94-0, black
Mounting
Screw fixing (M5)
Fitting position
Horizontal
Dimensions
168 x 145 x 100mm
Weight
Approx. 1.4kg
Op.*/storage temp.
-45 to +70ºC
Prot. type / Prot. class
IP20 / II (double insulated)
Note
Other heating capacities from 200W up available on request.
*Operating temperature of heater with integrated hygrostat: 0 to +60°C
Connection diagram
Art. No.
Model
Fan Heater with thermostat
230VAC, 50/60Hz
Heating capacity
Setting range
0 to +60°C
VDE + UL File No. E234324*
950W
Approvals
Fan Heater with hygrostat
230VAC, 50/60Hz
950W
65% RH, factory-set
VDE + UL File No. E234324*
Fan Heater with thermostat
120VAC, 50/60Hz
950W
+32 to +140°F
UL File No. E234324*
*according to UL499 in combination with UL508A
28
Operating voltage
950W
Compact high-performance
Fan Heater - CR 130
•
•
•
•
Compact design
Double insulated
Integrated thermostat or hygrostat
Optional clip or screw fixing
The compact high performance fan heater prevents formation of condensation and provides an evenly distributed interior air temperature in enclosures
with electric/electronic components. The plastic enclosure provides double
insulation and acts as protection against contact. The fan heater is available
with integrated thermostat or pre-set hygrostat for temperature or humidity
control. The CR 130 was designed as a stationary unit for wall fixing. For fixing on the bottom of the enclosure the fan heater CR 030 is recommended.
Technical Data:
Heating element
High performance cartridge
Temp. safety cut-out
to protect against overheating in case of fan failure,
automatic reset
Heater body
Extruded aluminium profile
Axial fan, ball bearing
Airflow 160m3/h, free flow
service life 50,000h at 25°C
Connection
2-pole max. 2.5mm2, clamping screw with strain relief, torque 0.8Nm
max.
Casing
Plastic according to UL94 V-0, black
Mounting
Clip for 35mm DIN rail, EN 60715 or screw fixing (M6)
Fitting position
Horizontal
Dimensions
182 x 160 x 99mm
Weight
Approx. 1.5kg
Op.*/storage temp.
-45 to +70ºC
Prot. type / Prot. class
IP20 / II (double insulated)
Note
Other heating capacities from 200W up available on request.
*Operating temperature of heater with integrated hygrostat: 0 to +60°C
Connection diagram
Art. No.
Model
Fan Heater with thermostat
Fan Heater with hygrostat
Fan Heater with thermostat
Operating voltage
Heating capacity
Setting range
Approvals
230VAC, 50/60Hz
950W
0 to +60°C
VDE + UL File No. E234324*
230VAC, 50/60Hz
950W
65% RH, factory-set
VDE + UL File No. E234324*
120VAC, 50/60Hz
950W
+32 to +140°F
UL File No. E234324*
*according to UL499 in combination with UL508A
29
1,200W
Compact high-performance semiconductor
Fan Heater - CS 030
•
•
•
•
Compact design
High heating performance
Double insulated
Integrated thermostat (optional)
The compact high performance fan heater prevents formation of condensation and provides an evenly distributed interior air temperature in enclosures
with electric/electronic components. The plastic enclosure provides double
insulation and acts as pretection against contact. The fan heater is available
with optional integrated thermostat for temperature control. The CS 030 was
designed as a stationary unit for the bottom of the enclosure. For wall fixing
the fan heater CS 130 is recommended.
Technical Data:
Heating element
PTC resistor - temperature limiting
Temp. safety cut-out
to protect against overheating in case of fan failure
Axial fan, ball bearing
Airflow 160m3/h, free flow
service life 50,000h at 25°C
Connection
2-pole clamp max. 2.5mm2, clamping screw with strain relief, torque
0.8Nm max.
Casing
Plastic according to UL94-0, black
Mounting
Screw fixing (M5)
Fitting position
Horizontal
Dimensions
168 x 145 x 120mm
Weight
Approx. 1.2kg
Op./storage temp.
-45 to +70ºC
Prot. type / Prot. class
IP20 / II (double insulated)
Heating capacity (W)
30
Heating capacity / Ambient temperature
diagram CS 030
Connection diagram
Art. No.
83268
83269
1)
30
Temperature (ºC)
Model
Operating voltage
Heating capacity1)
Inrush current max.
Fan Heater without thermostat
230VAC, 50/60Hz
1,200W
Fan Heater with thermostat
120VAC, 50/60Hz
1,200W
Fan Heater without thermostat
120VAC, 50/60Hz
1,200W
Fan Heater with thermostat
230VAC, 50/60Hz
at 20°C ambient temperature; 2)according to UL499 in combination with UL508A
1,200W
13A
Setting range
Approvals
0 to +60°C
VDE + UL File No. E2343242)
13A
-
VDE + UL File No. E2343242)
16A
+32 to +140°C
UL File No. E2343242)
16A
-
UL File No. E2343242)
1,200W
Compact high-performance semiconductor
Fan Heater - CS 130
•
•
•
•
•
Compact design
High heating performance
Double insulated
Integrated thermostat (optional)
Optional clip or screw fixing
The compact high performance fan heater prevents formation of condensation and provides an evenly distributed interior air temperature in enclosures
with electric/electronic components. The plastic enclosure provides double
insulation and acts as protection against contact. The fan heater is available
with optional integrated thermostat for temperature control. The CS 130 was
designed as a stationary unit for wall fixing. For fixing on the bottom of the
enclosure the fan heater CS 030 is recommended.
Technical Data:
Heating element
PTC resistor - temperature limiting
Temp. safety cut-out
to protect against overheating in case of fan failure
Axial fan, ball bearing
Airflow 160m3/h, free flow
service life 50,000h at 25°C
Connection
2-pole max. 2.5mm2, clamping screw with strain relief, torque 0.8Nm
max.
Casing
Plastic according to UL94 V-0, black
Mounting
Clip for 35mm DIN rail, EN 60715 or screw fixing (M6)
Fitting position
Horizontal
Dimensions
182 x 160 x 120mm
Weight
Approx. 1.3kg
Op.*/storage temp.
-45 to +70ºC
Prot. type / Prot. class
IP20 / II (double insulated)
Heating capacity (W)
Heating capacity / Ambient temperature
diagram CS 130
Temperature (ºC)
Connection diagram
Art. No.
83266
83267
1)
Model
Fan Heater with thermostat
Operating voltage
230VAC, 50/60Hz
Heating capacity1)
1,200W
Inrush current max.
13A
Setting range
Approvals
0 to +60°C
VDE + UL File No. E2343242)
VDE + UL File No. E2343242)
Fan Heater without thermostat
230VAC, 50/60Hz
1,200W
13A
-
Fan Heater with thermostat
120VAC, 50/60Hz
1,200W
16A
+32 to +140°F
UL File No. E2343242)
Fan Heater without thermostat
120VAC, 50/60Hz
1,200W
16A
-
UL File No. E2343242)
at 20°C ambient temperature; 2)according to UL499 in combination with UL508A
31
21m3/h to 102m3/h
Filter Fan FF 018 Series
•
•
•
•
•
Very low noise
Minimal depth in enclosure
Functional design
Time-saving installation
Weather proof and UV resistant
Filter fans are used to provide an optimum climate in enclosures. The interior
temperature of an enclosure can be reduced by channelling cooler filtered
outside air into the enclosure thus expelling heated internal air. The resulting
air flow prevents formation of localised hot pockets and protects the electronic components from overheating. The plastic used for the hood of this
filter fan series is highly weather proof and UV light resistant.
Technical Data:
Axial fan, ball bearing
Service life 50,000h at 25°C (65% RH)
fan body aluminium, rotor plastic
Connection
2 wires with pressure clamps 2.5mm2, length 100mm
Casing (filter fan and exit filter)
Plastic according to UL94-V-0, light grey
Hood (filter fan and exit filter)
Plastic according to UL94 V-0, light grey;
weather proof and UV light resistant according to UL746C (f1)
Mounting frame
with double-sided industrial adhesive band for fixing to the outside of
enclosure; certain operating circumstances can make the additional
use of screws necessary (see drilling template); included in the delivery
of the filter fans is a template for the enclosure cut-out.
Filter mat
G4 acc. to DIN EN 779, filtering degree 94%
Filter material
Synthetic fibre with progressive construction, temperature resistant
to 100°C, self-extinguishing class F1; moisture resistant to 100% RH,
reusable - cleaning by washing or vacuuming
Op./storage temp.
-45 to +70ºC
Prot. type / Prot. class
IP54* / I (earthed)
*Using fine filter mats type F5 increases the protection type to IP55, bt reduces the air volume.
Special features:
•
The self-adhesive seal of the mounting frame prevents dust and water from entering the cabinet.
•
Functional design of the intake and exit fan hoods very effectively prevents direct intrusion of falling
water and dust. The advantage is that the filter mat does not get so quickly contaminated with dirt and
thus does not need to be exchanged so often.
•
The air channelling makes the filter fan particularly quiet in operation.
•
Functional and modern design enables time-saving assembly and maintenance.
•
All filter fan models are also available with integrated airflow monitor.
•
EMC versions and other voltages on request.
•
The direction of air can easily be switched by reversing the axial fan (sizes 1 to 3).
Art. No.
32
Operating
voltage
Air volume,
free flow
Air volume
with
exit filter
Current
consumption
Power
consumption
Average noise
level (DIN EN
ISO 4871)
Depth in
enclosure
Enclosure
cut-out
Weight
(approx.)
Approvals
230VAC,
50Hz
21m3/h
31dB (A)
45mm
97 x 97mm
+0.4
0.6kg
VDE + UL File
No. E234324
230VAC,
50Hz
55m3/h
42m3/h
100mA
15W
40dB (A)
58mm
125 x
125mm +0.4
1.0kg
VDE + UL File
No. E234324
230VAC,
50Hz
102m3/h
68m3/h
100mA
15W
39dB (A)
86mm
176 x
176mm +0.4
1.3kg
VDE + UL File
No. E234324
120VAC,
60Hz
24m3/h
18m3/h
160mA
13W
31dB (A)
45mm
97 x 97mm
+0.4
0.6kg
UL File No.
E234324
120VAC,
60Hz
63m3/h
48m3/h
180mA
15W
40dB (A)
58mm
125 x
125mm +0.4
1.0kg
UL File No.
E234324
120VAC,
60Hz
117m3/h
78m3/h
180mA
15W
39dB (A)
86mm
176 x
176mm +0.4
1.3kg
UL File No.
E234324
16m3/h
80mA
13W
Filter Fan FF 018 Series
Time-saving assembly and maintenance
SAN’s filter fans are easily installed by one person from outside the cabinet.
1.
2.
3.
4.
Changing the filter mat or fan is quickly done by one person. To change the filter
mat simply remove the filter hood, insert the new mat and snap the hood back
again. No tools required. Maintenance of the fan can easily be done without
removing the mounting frame (2).
Installation sketch
Dimensional Drawing
Size 1
Make cut-out in the cabinet wall. The cut edge of the cabinet opening
should be free of dirt, fillings and grease. A template for the enclosure cutout is included in the delivery of the filter fan.
Remove protective film from the sealing strips on the mounting frame.
Press mounting frame into the cabinet opening. The frame stays permanently in the cabinet. (For size 176mm and up we recommend additional
screw fixing.)
Electrically connect the axial fan using the clip connectors. Push the unit
into the mounting frame. Fix using screws.
Insert the filter mat in the hood. Clip on. Finished.
Size 2
Size 3
Drilling template for mounting frame
Exit filter EF 118 Series
Art. No.
Depth in enclosure
Enclosure cut-out
Weight (approx.)
0.3kg
G4 acc. to DIN EN 779, filtering degree 94%
Filter mat
Protection type
16mm
125x125mm +0.4
0.4kg
G4 acc. to DIN EN 779, filtering degree 94%
IP54*
16mm
176x176mm +0.4
0.6kg
G4 acc. to DIN EN 779, filtering degree 94%
IP54*
16mm
97x97mm +0.4
IP54*
*Using fine filter mats type F5 increases the protection type to IP55, but reduces the air volume.
Filter Mats FM 086 / FFM 086
Filter mat
89 x 89mm
118 x 118mm
168 x 168mm
F5 (1 packing unit = 3 pcs)
Art. no.
Art. no.
Art. no.
G4 (1 packing unit = 3 pcs)
Art. no.
Art. no.
Art. no.
Filter Fan with Airflow Monitor FFLC 218 (Normally Closed)
Airflow monitor integrated
in protective grille of filter
fan, e.g. Art. no.
Art. No.
Operating
voltage
Air volume,
free flow
Air volume with
exit filter
Power
consumption
Average noise
level (DIN EN
ISO 4871)
Depth in
enclosure
230VAC, 50Hz
21m3/h
16m3/h
80mA
230VAC, 50Hz
55m /h
42m3/h
31dB (A)
100mA
15W
40dB (A)
230VAC, 50Hz
102m3/h
68m3/h
100mA
15W
39dB (A)
120VAC, 60Hz
24m3/h
18m3/h
160mA
13W
120VAC, 60Hz
63m3/h
48m3/h
180mA
120VAC, 60Hz
117m3/h
78m3/h
180mA
3
Current consumption
For techinal data see Airflow Monitor LC 013/LCF 013 (Normally Closed, Normally Open)
Enclosure cut-out
Weight
(approx.)
45mm
97 x 97mm +0.4
0.6kg
58mm
125 x 125mm +0.4
1.0kg
86mm
176 x 176mm +0.4
1.3kg
31dB (A)
45mm
97 x 97mm +0.4
0.6kg
15W
40dB (A)
58mm
125 x 125mm +0.4
1.0kg
15W
39dB (A)
86mm
176 x 176mm +0.4
1.3kg
13W
33
200m3/h
Filter Fan FF 018 Series
•
•
•
•
•
Low maintenance
High through-flow air volume
Functional design
Time-saving installation
Weather proof and UV resistant
Filter fans are used to provide an optimum climate in enclosures. The interior
temperature of an enclosure can be reduced by channelling cooler filtered
outside air into the enclosure thus expelling heated internal air. The resulting
air flow prevents formation of localised hot pockets and protects the electronic components from overheating. The plastic used for the hood of this
filter fan series is highly weather proof and UV light resistant.
Technical Data:
Filter Fan
Axial fan, ball bearing
Service life 50,000h at 25°C (65% RH)
fan body aluminium, rotor metal
Connection
3-pole clamp for 2.5mm2, clamping torque 0.8Nm max.
Casing (filter fan and exit filter)
Plastic according to UL94-V-0, light grey
Hood (filter fan and exit filter)
Plastic according to UL94 V-0, light grey;
weather proof and UV light resistant according to UL746C (f1)
Mounting frame
with double-sided industrial adhesive band for fixing to the outside of
enclosure; certain operating circumstances can make the additional use of
screws necessary (see drilling template); included in the delivery of the filter
fans is a template for the enclosure cut-out.
Filter mat
G4 acc. to DIN EN 779, filtering degree 94%
Filter material
Synthetic fibre with progressive construction, temperature resistant to
100°C, self-extinguishing class F1; moisture resistant to 100% RH, reusable
- cleaning by washing or vacuuming
Op./storage temp.
-45 to +70ºC
Prot. type / Prot. class
IP54* / I (earthed)
Exit filter
View from
rear
*Using fine filter mats type F5 increases the protection type to IP55, but reduces the air volume.
Airflow monitor integrated
in protective grille of filter
fan, e.g. Art. no.
Filter Fan FF 018 Series
Art. No.
Operating
voltage
Air volume,
free flow
230VAC,
50Hz
200m3/h
120VAC,
60Hz
230m3/h
Drilling template
for mounting
frame
Air volume
with
exit filter
Current
consumption
Power
consumption
Average noise
level (DIN EN
ISO 4871)
Depth in
enclosure
Enclosure
cut-out
Weight
(approx.)
Approvals
52dB (A)
95mm
176x176mm
+0.4
1.7kg
UL File No.
E234324
143m3/h
470mA
39W
52dB (A)
95mm
176x176mm
+0.4
1.7kg
UL File No.
E234324
125m3/h
320mA
45W
Exit filter EF 118 Series
Art. No.
Depth in enclosure
16mm
Enclosure cut-out
176x176mm +0.4
Weight (approx.)
0.6kg
Filter mat
G4 acc. to DIN EN 779, filtering degree 94%
Protection type
IP54*
*Using fine filter mats type F5 increases the protection type to IP55, but reduces the air volume.
Filter Mats FM 086 / FFM 086
Filter mat
168x168mm
F5 (1 packing unit = 3 pcs)
Art. no.
G4 (1 packing unit = 3 pcs)
Art. no.
Filter Fan with Airflow Monitor FFLC 218 (Normally Closed)
Art. No.
34
Operating
voltage
Air volume,
free flow
Air volume with
exit filter
Current consumption
230VAC, 50Hz
200m3/h
125m3/h
320mA
120VAC, 60Hz
230m3/h
143m3/h
470mA
Power
consumption
Average noise
level (DIN EN
ISO 4871)
Depth in
enclosure
Enclosure cut-out
Weight
(approx.)
52dB (A)
95mm
176x176mm +0.4
1.7kg
39W
52dB (A)
95mm
176x176mm +0.4
1.7kg
45W
300m3/h
Filter Fan FF 018 Series
•
•
•
•
•
•
Very low noise
Minimal depth in enclosure
High through-flow air volume
Uniform air circulation
High reliability
Weather proof and UV resistant
Filter fans are used to provide an optimum climate in enclosures. The interior
temperature of an enclosure can be reduced by channelling cooler filtered
outside air into the enclosure thus expelling heated internal air. The resulting
air flow prevents formation of localised hot pockets and protects the electronic components from overheating. Four integrated axial fans provide a
particularly high and uniform air circulation thus contributing to higher reliability. The plastic used for the hood of this filter fan series is highly weather
proof and UV light resistant.
Technical Data:
4x Axial fan
Axial fan, ball bearing
Service life 50,000h at 25°C (65% RH)
fan body aluminium, rotor metal
Connection
3-pole clamp for 2.5mm2, clamping torque 0.8Nm max.
Casing (filter fan and exit filter)
Plastic according to UL94-V-0, light grey
Hood (filter fan and exit filter)
Plastic according to UL94 V-0, light grey;
weather proof and UV light resistant according to UL746C (f1)
Mounting frame
with double-sided industrial adhesive band for fixing to the outside of enclosure; certain operating circumstances can make the additional use of screws
necessary (see drilling template); included in the delivery of the filter fans is a
template for the enclosure cut-out.
Filter mat
G4 acc. to DIN EN 779, filtering degree 94%
Filter material
Synthetic fibre with progressive construction, temperature resistant to 100°C,
self-extinguishing class F1; mooisture resistant to 100% RH, reusable cleaning by washing or vacuuming
Op./storage temp.
-45 to +70ºC
Prot. type / Prot. class
IP54* / I (earthed)
View from
rear
Exit filter
*Using fine filter mats type F5 increases the protection type to IP55, but reduces the air volume.
Drilling template
for mounting
frame
Filter Fan FF 018 Series
Art. No.
Operating
voltage
Air volume,
free flow
230VAC,
50Hz
300m3/h
120VAC,
60Hz
345m3/h
Air volume
with
exit filter
Current
consumption
Power
consumption
Average noise
level (DIN EN
ISO 4871)
Depth in
enclosure
Enclosure
cut-out
Weight
(approx.)
Approvals
53dB (A)
65mm
250x250mm
+0.4
3.3kg
UL File No.
E234324
264m3/h
700mA
60W
53dB (A)
65mm
250x250mm
+0.4
3.3kg
UL File No.
E234324
230m3/h
400mA
60W
Exit filter EF 118 Series
Art. No.
Depth in enclosure
22mm
Enclosure cut-out
250x250mm +0.4
Weight (approx.)
1.0kg
Filter mat
G4 acc. to DIN EN 779, filtering degree 94%
Protection type
IP54*
*Using fine filter mats type F5 increases the protection type to IP55, but reduces the air volume.
Filter Mats FM 086 / FFM 086
Filter mat
247x247mm
F5 (1 packing unit = 3 pcs)
Art. no.
G4 (1 packing unit = 3 pcs)
Art. no.
35
550m3/h
Filter Fan FF 018 Series
•
•
•
•
High through-flow air volume
Functional design
Time-saving installation
Weather proof and UV resistant
Filter fans are used to provide an optimum climate in enclosures. The interior
temperature of an enclosure can be reduced by channelling cooler filtered
outside air into the enclosure thus expelling heated internal air. The resulting
air flow prevents formation of localised hot pocket and protects the electronic components from overheating. The high-performance axial fan provides
high air circulation. The plastic used for the hood of this filter fan series is
highly weather proof and UV light resistant.
Technical Data:
Filter Fan
Axial fan, ball bearing
Service life 50,000h at 25°C (65% RH)
fan body aluminium, rotor metal
Connection
3-pole clamp for 2.5mm2, clamping torque 0.8Nm max.
Casing (filter fan and exit filter)
Plastic according to UL94-V-0, light grey
Hood (filter fan and exit filter)
Plastic according to UL94 V-0, light grey;
weather proof and UV light resistant according to UL746C (f1)
Mounting frame
with double-sided industrial adhesive band for fixing to the outside of enclosure; certain operating circumstances can make the additional use of screws
necessary (see drilling template); included in the delivery of the filter fans is a
template for the enclosure cut-out.
Filter mat
G4 acc. to DIN EN 779, filtering degree 94%
Filter material
Synthetic fibre with progressive construction, temperature resistant to 100°C,
self-extinguishing class F1; moisture resistant to 100% RH, reusable - cleaning by washing or vacuuming
Op./storage temp.
-45 to +70ºC
Prot. type / Prot. class
IP54* / I (earthed)
Airflow monitor integrated
in protective grille of filter
fan, e.g. Art. no.
*Using fine filter mats type F5 increases the protection type to IP55, but reduces the air volume.
Filter Fan FF 018 Series
Art. No.
Operating
voltage
Air volume,
free flow
230VAC,
50Hz
550m3/h
120VAC,
60Hz
632m3/h
Exit filter
View from
rear
Drilling template
for mounting
frame
Air volume
with
exit filter
Current
consumption
Power
consumption
Average noise
level (DIN EN
ISO 4871)
Depth in
enclosure
Enclosure
cut-out
Weight
(approx.)
Approvals
65dB (A)
107mm
250x250mm
+0.4
2.7kg
UL File No.
E234324
345m3/h
780mA
85W
65dB (A)
107mm
250x250mm
+0.4
2.7kg
UL File No.
E234324
300m3/h
300mA
64W
Exit filter EF 118 Series
Art. No.
Depth in enclosure
22mm
Enclosure cut-out
250x250mm +0.4
Weight (approx.)
1.0kg
Filter mat
G4 acc. to DIN EN 779, filtering degree 94%
Protection type
IP54*
*Using fine filter mats type F5 increases the protection type to IP55, but reduces the air volume.
Filter Mats FM 086 / FFM 086
Filter mat
247x247mm
F5 (1 packing unit = 3 pcs)
Art. no.
G4 (1 packing unit = 3 pcs)
Art. no.
Filter Fan with Airflow Monitor FFLC 218 (Normally Closed)
Art. No.
36
Operating
voltage
Air volume,
free flow
Air volume with
exit filter
Current consumption
230VAC, 50Hz
550m3/h
300m3/h
300mA
120VAC, 60Hz
632m3/h
345m3/h
780mA
Power
consumption
Average noise
level (DIN EN
ISO 4871)
Depth in
enclosure
Enclosure cut-out
Weight
(approx.)
65dB (A)
107mm
250x250mm +0.4
2.7kg
85W
65dB (A)
107mm
250x250mm +0.4
2.7kg
64W
Outdoor
Filter Fan - FF 018 Series
•
•
•
•
Filter changeable from outside
Safe, lockable
Impact resistant
Weather proof and UV resistant
The outdoor filter fan can be used in outdoor enclosures where warm air has
to be dissipated on account of increased thermic development. To clean and
exchange the filter mat, it is only necessary to open the lockable door of the
outdoor hood. A protection type of IP55 is achieved due to the special design of the hood and the use of fine filter mats. The plastic casing is impact
resistant, highly weather proof and resistant to UV light.
Outdoor Filter Fan
Technical Data:
Axial fan, ball bearing
Service life min. 50,000h at 25°C (65% RH)
fan body aluminium, rotor plastic
Connection
2 wires with pressure clamps 2.5mm2, length 100mm
Casing (filter fan and exit filter)
Casing material high impact plastic ASA, light grey burning behaviour according to UL94 H-B; high resistance to weather and UV
Mounting frame
with double-sided industrial adhesive band for fixing to the outside of enclosure; certain operating circumstances can make the additional use of screws
necessary (see drilling template); included in the delivery of the filter fans is a
template for the enclosure cut-out.
Filter mat
F5 acc. to DIN EN 779, filtering degree 98%
Filter material
Synthetic fibre with progressive construction, temperature resistant to 100°C,
self-extinguishing class F1; moisture resistant to 100% RH
Op./storage temp.
-45 to +70ºC
Prot. type / Prot. class
IP55 / I (earthed)
Approvals
UL File No. E234324
View from
rear
The hood is fixed permanently to the enclosure from the inside using screws. Filter mats can be easily
changed from outside the enclosure through the lockable door in the hood.
Drilling template
for mounting
frame
Filter Fan with Airflow Monitor FFLC 218 (Normally Closed)
Art. No.
Operating voltage
Outdoor Exit filter
Air volume,
free flow
Current consumption
230VAC, 50Hz
20m3/h
100mA
120VAC, 60Hz
23m3/h
180mA
Power
consumption
Average noise level
(DIN EN ISO 4871)
Depth in
enclosure
Enclosure cut-out
Weight
(approx.)
15W
40dB (A)
62mm
125x125mm +0.4
1.2kg
15W
40dB (A)
62mm
125x125mm +0.4
1.2kg
Exit filter EF 118 Series
Art. No.
Depth in enclosure
16mm
Enclosure cut-out
125x125mm +0.4
Weight (approx.)
0.6kg
Filter mat
F5 acc. to DIN EN 779, filtering degree 98%
Protection type
IP55
Filter Mats FFM 086
Filter mat
F5 (1 packing unit = 3 pcs)
122x122mm
Art. no.
37
350m3/h
Low noise
Roof Filter Fan - RFF 018 Series
•
•
•
•
•
•
Very low noise
Minimal depth in enclosure
High through-flow air volume
Uniform air circulation
High reliability
Time-saving installation
Roof filter fans and roof exit filters find use in
enclosures, from which warm air has to be diverted due to increased heat
development. The ready-to-connect and low-noise roof filter fan, which
houses four axial fans, is used to expel warm air from within the enclosure
which has been generated by the stray power of the components. The roof
exit filter provides passive ventilation.
Roof Filter Fan RFF 018
Technical Data:
Axial fans, ball bearing
Service life 50,000h at 25°C (65% RH)
fan body aluminium, rotor plastic
Connection
3-pole clamp for 2.5mm2
Casing
Plastic according to UL94-V-0 / lacquered steel sheet, light grey
Filter mat
G3 acc. to DIN EN 779, filtering degree 85%
Filter material
Synthetic fibre with progressive construction, temperature resistant to 100°C,
self-extinguishing class F1; moisture resistant to 100% RH, reusable - cleaning by washing or vacuuming
Op./storage temp.
-45 to +70ºC
Prot. type
IP43 (with filter mat G3 / IP33 (without filter mat)
Prot. class
I (earthed)
Approvals
UL FIle No. E234324
Roof Exit filter
REF 118
View from
below
Hole centers
Important note: For reasons of pressure compensation the roof filter fan must always be operated in combination with another filter fan (e.g. Art. No. ) or a passive intake filter (e.g. Art. No.).
Enclosure cut-out
Roof Filter Fan RFF 018 Series
Art. No.
Operating
voltage
Air volume,
free flow
Air volume with
exit filter
Current consumption
230VAC, 50Hz
350m3/h (w/
filter mat G3)
500m3/h (w/o
filter mat)
400mA
120VAC, 60Hz
402m3/h (w/
filter mat G3)
575m3/h (w/o
filter mat)
700mA
Power
consumption
Average noise
level (DIN EN
ISO 4871)
Depth in
enclosure
Enclosure cut-out
Weight
(approx.)
55dB (A)
44mm
250x250mm +0.4
4.4kg
60W
55db (A)
44mm
250x250mm +0.4
4.4kg
60W
Roof Exit filter REF 118 Series
Art. No.
Depth in enclosure
none
Enclosure cut-out
250x250mm +0.4
Weight (approx.)
2.0kg
Filter mat
G3 acc. to DIN EN 779, filtering degree 85%
Filter Mats FM 086
Filter mat
G3 (1 packing unit = 3 pcs)
38
282x282mm
Art. no.
Protection type
IP43 (w/filter mat)
High-performance
19” Fan Tray - LE 019 Series
•
•
•
•
•
High air output
Long service life
Ball bearing fans
Ready for connection
Optical function indicator
Compact high performance fan tray for enforced circulation of air in switch
and server enclosures and for concerted cooling of 19” component groups.
Natural convection is improved and the formation of localised hot pockets is
avoided. Also available with integrated thermostat (see photo).
Technical Data:
Axial fans, ball bearing
Service life 50,000h at 25°C (65% RH)
fan body aluminium, rotor plastic
Material
Front panel aluminium, bright anodised
casing steel sheet, electrogalvanized
Optical indicator
Integrated in front panel
Connection
Appliance power inlet on rear of casing, plug included
Fitting position
Horizontal (direction of air upwards)
Op./storage temp.
-45 to +70ºC
Prot. type / Prot. class
IP20 / I (earthed)
Approvals
UL FIle No. E234324
Note:
We recommend using the fan tray in combination with our dual thermostat (ZR 011) for regulating temperature
in electronic enclosures and for protection against overheating due to possible fan failure. The dual thermostat regulates the operation of the fan tray and when connected to a signal device also triggers an early
warning if the enclosure interior temperature rises above a set limit.
When using a fan tray with integrated thermostat, the use of an additional thermostat (KTS 011) provides the
extra safety of activating a signal device.
Art. No.
Model
No. of
fans
Operating
voltage
Air flow,
free flow
Power
consumption
without thermostat
3
230VAC, 50Hz
486m3/h
Speed (rpm-1)
Impact
pressure
Weight
(approx.)
45W
55dB (A)
2600 min-1 (50Hz)
with thermostat 0 to +60°C
3
230VAC, 50Hz
486m /h
74Pa
3.0kg
45W
55db (A)
2600 min-1 (50Hz)
74Pa
without thermostat
6
230VAC, 50Hz
3.4kg
972m3/h
90W
57dB (A)
2600 min-1 (50Hz)
74Pa
with thermostat 0 to +60°C
6
5.3kg
230VAC, 50Hz
972m3/h
90W
57dB (A)
2600 min-1 (50Hz)
74Pa
without thermostat
5.7kg
9
230VAC, 50Hz
1458m3/h
135W
58dB (A)
2600 min-1 (50Hz)
74Pa
7.8kg
with thermostat 0 to +60°C
9
230VAC, 50Hz
1458m3/h
135W
58dB (A)
2600 min-1 (50Hz)
74Pa
7.9kg
without thermostat
3
120VAC, 60Hz
576m3/h
45W
55dB (A)
2900 min-1 (60Hz)
88Pa
3.0kg
with thermostat 0 to +60°C
3
120VAC, 60Hz
576m3/h
45W
55dB (A)
2900 min-1 (60Hz)
88Pa
3.4kg
without thermostat
6
120VAC, 60Hz
1152m3/h
90W
57dB (A)
2900 min-1 (60Hz)
88Pa
5.3kg
with thermostat 0 to +60°C
6
120VAC, 60Hz
1152m3/h
90W
57dB (A)
2900 min-1 (60Hz)
88Pa
5.7kg
witout thermostat
9
120VAC, 60Hz
1728m3/h
135W
58dB (A)
2900 min-1 (60Hz)
88Pa
7.8kg
with thermostat 0 to +60°C
9
120VAC, 60Hz
1728m3/h
135W
58dB (A)
2900 min-1 (60Hz)
88Pa
7.9kg
3
Average noise
level (DIN EN
ISO 4871)
39
24VDC + 48VDC
Switch Module SM 010
•
•
•
•
•
High DC switching capacity
Variety of applications
Compact design
Simple connection
Cliip fixing
Switch module for switching DC appliances with high switching capacity. A
separate conventional switch contact is used as controller (e.g. temperature
regulator, humidity regulator). The switch module is available in 24VDC and
48VDC versions.
Technical Data:
Contact type
Contact maker, normally open (Relay/MOSFET)
Contact resistance
<10mΩ
Service life
>100,000 cycles
EMC
acc. to EN 55014-1-2, EN 61000-3-2, EN 61000-3-3
Connection
6-pole terminal, clamping torque 0.5Nm max.:
rigid wire 2.5mm2
stranded wire (with wire end ferrule) 1.5mm2
Mounting
Clip for 35mm DIN rail, EN60715
Casing
Plastic according to UL94 V-0, light grey
Dimensions
67x50x46mm
Weight
Approx. 90g
Fitting position
Variable
Op./storage temp.
-45 to +70°C
Protection type
IP20
Approvals
VDE submitted
e.g.
Temperature
regulator
Power supply
e.g. Heater
Load e.g. heater,
cooling device with
temperature cut-out
Switch Module,
SM 010
Control contact,
e.g. temperature,
humidity or pressure
regulator
Load, e.g. heater,
cooling device without
temperature cut-out
Switch Module,
SM 010
Control contact,
e.g. temperature,
humidity or pressure
regulator
Fan
Art. No.
40
Operating voltage
Max. Switching capacity
48VDC (38-56VDC)
56VDC 16A
24VDC (20-28VDC)
28VDC 16A
Small, compact
Thermostat - KTO/KTS 011
•
•
•
•
Large setting range
Small size
Simple to mount
High switching performance
KTO 011: Thermostat (normally closed), contact breaker for regulating heaters.
KTS 011: Thermostat (normally open), contact maker for regulating of filter
fans and heat exchangers or for switching signal devices when temperature
limit has been exceeded.
Technical Data:
Switch temperature difference
7K (±4K tolerance)
Sensor element
Thermostatic bimetal
Contact type
Snap-action contact
Contact resistance
<10mΩ
Service life
>100,000 cycles
Max. switching capacity
250VAC, 10 (2) A
120VAC, 15 (2) A
DC 30W
EMC
acc. to EN 55014-1-2, EN 61000-3-2, EN 61000-3-3
Connection
2-pole terminal, clamping torque 0.5Nm max.:
rigid wire 2.5mm2
stranded wire (with wire end ferrule) 1.5mm2
Mounting
Clip for 35mm DIN rail, EN60715 (or for exit filter EF 118 Series)
Casing
Plastic according to UL94 V-0, light grey
Dimensions
60x33x43mm
Weight
Approx. 40g
Fitting position
Variable
Op/storage temp.
-45 to +80°C
Protection type
IP20
Thermostat
KTO 011 (NC)
Heater
Thermostat e.g. Fan
KTS 011 (NO)
Thermostat
KTO 011 (NC)
Thermostat e.g. Signal
device
KTS 011 (NO)
Thermostat
KTS 011 (NO)
Heater
Filter fan,
Cooling equipment,
Signal device
Example of connection
Setting range
0 to +60°C
-10 to +50°C
Art. No. Contact Breaker (NC)
Connection diagrams
Art. No. Contact Maker (NO)
Approvals
VDE
VDE
+20 to +80°C
VDE
+32 to +140°F
UL File No. E164102
+14 to +122°F
UL File No. E164102
0 to +60°C
UL File No. E164102
41
Tamperproof (Pre-set)
Thermostats - FTO/FTS 011
•
•
•
•
Small size
Default temperature settings
Easy to install
High switching tolerance
Tamperproof (Pre-set) Thermostat FTO 011
Contact breaker / NC (red casing) for regulating heaters or for switching
signal devices when temperature has fallen below the minimum value. The
contact opens when temperature is rising.
Tamperproof (Pre-set) Thermostat FTS 011
Contact maker / NO (blue casing) for regulating filter fans, heat exchangers,
cooling devices or for switching signal devices when temperature limit has
been exceeded. The contact closes when temperature is rising.
Technical Data:
Sensor element
Thermostatic bimetal
Contact type
Snap-action contact
Contact resistance
<20mΩ
Service life
>100,000 cycles
Max. switching capacity
250VAC, 5 (1.6) A
120VAC, 10 (2) A
DC 30W
Max. inrush current
AC 10A
EMC
acc. to EN 55014-1-2, EN 61000-3-2, EN 61000-3-3
Connection
2-pole terminal for 2.5mm2, torque 0.8Nm max.
Mounting
Clip for 35mm DIN rail, EN60715
Casing
Plastic according to UL94 V-0, light grey
Dimensions
47x33x33mm
Weight
Approx. 30g
Fitting position
Variable
Op/storage temp.
-20 to +80°C / -45 to +80°C
Protection type
IP20
Approvals
VDE + UL File No. E164102
Heater
Thermostat Thermostat
FTO 011
FTS 011
Filter fan
Thermostat
FTS 011
Signal device
Example of connection
Art. No.
Contact
Switch-off temperature
Switch-on temperature
Contact breaker (NC)
+25°C (±5K tolerance)
+15°C (±5K tolerance)
Contact breaker (NC)
+5°C (±5K tolerance)
Switch-on temperature
Switch-off temperature
Contact maker (NO)
+60°C (±6K tolerance)
+50°C (±7K tolerance)
Contact maker (NO)
+35°C (±6K tolerance)
+25°C (±7K tolerance)
Contact maker (NO)
42
+15°C (±5K tolerance)
+50°C (±6K tolerance)
+40°C (±7K tolerance)
Dual
Thermostat - ZR 011
•
•
•
•
•
NO and NC in one casing
Separate adjustable temperatures
High switching capacity
Terminals easily accessible
Clip fixing
Two thermostats in one casing:
Thermostat (contact breaker, normally closed) for regulating
heaters.
Thermostat (contact maker, normally open) for regulating
filter fans and heat exchangers or switching signal devices
when temperature limit has been exceeded.
Heaters and cooling equipment can be switched independently from each other with a temperature offset as opposed to the usual change-over contacts.
Technical Data:
Switch temperature difference
7K (±4K tolerance)
Sensor element
Thermostatic bimetal
Contact type
Snap-action contact
Contact resistance
<10mΩ
Service life
>100,000 cycles
Max. switching capacity
250VAC, 10 (2) A
120VAC, 15 (2) A
DC 30W
EMC
acc. to EN 55014-1-2, EN 61000-3-2, EN 61000-3-3
Connection
4-pole terminal, clamping torque 0.5Nm max.:
rigid wire 2.5mm2
stranded wire (with wire end ferrule) 1.5mm2
Mounting
Clip for 35mm DIN rail, EN60715
Casing
Plastic according to UL94 V-0, light grey
Dimensions
67x50x46mm
Weight
Approx. 90g
Fitting position
Variable
Op/storage temp.
-45 to +80°C
Protection type
IP20
Approvals
UL File No. E164102
Thermostat
ZR 011 (NC/NO)
Heater
Filter fan,
Cooling equipment,
Signal device
Connection diagram
Art. No.
Setting Range
Setting Range
contact breaker, normally closed
0 to +60°C
Contact maker, normally open
0 to +60°C
contact breaker, normally closed
+32 to +140°F
Contact maker, normally open
+32 to +140°F
contact breaker, normally closed
-10 to +50°C
Contact maker, normally open
+20 to +80°C
contact breaker, normally closed
+14 to +122°F
Contact maker, normally open
+68 to +176°F
Contact maker, normally open
0 to +60°C
Contact maker, normally open
0 to +60°C
Contact maker, normally open
+32 to +140°F
Contact maker, normally open
+32 to +140°F
43
Tamperproof (Pre-set)
Dual-Thermostat - FTD 011
•
•
•
•
NO and NC in one casing
Default temperature settings
High switching accuracy
Clip fixing
Two thermostats in one casing:
Tamperproof (Pre-set) Thermostat/Contact breaker (NC)
for regulating heaters or for switching signal devices when temperature has
fallen below the minimum value. The contact opens when temperature is rising.
Tamperproof (Pre-set) Thermostat/Contact maker (NO)
for regulating filter fans, heat exchangers or for switching signal devices when
temperature limit has been exceeded. The contact closes when temperature is
rising.
Heaters and cooling equipment can be switched independently from each
other with a temperature offset as opposed to the usual change-over contacts.
Technical Data:
Sensor element
Thermostatic bimetal
Contact type
Snap-action contact
Contact resistance
<20mΩ
Service life
>100,000 cycles
Max. switching capacity
250VAC, 5 (1.6) A
120VAC, 10 (2) A
DC 30W
Max. inrush current
AC 10A
EMC
ac. to EN 55014-1-2, EN 61000-3-2, EN 61000-3-3
Connection
4-pole terminal for 12.5mm2, torque 0.8Nm max.
Mounting
Clip for 35mm DIN rail, EN60715
Casing
Plastic according to UL94 V-0, light grey
Dimensions
47x63x33mm
Weight
Approx. 40g
Fitting position
Variable
Op/storage temp.
-20 to +80°C / -45 to +80°C
Protection type
IP20
Approvals
VDE + UL File No. E164102
Heater
Filter fan
Thermostat
FTD 011
Example of connection
Art. No.
Contact breaker (NC)
Switch-on temperature
Switch-on temperature
Switch-off temperature
+25°C (±5K tolerance)
+15°C (±5K tolerance)
+60°C (±6K tolerance)
+50°C (±7K tolerance)
+15°C (±5K tolerance)
+5°C (±5K tolerance)
+35°C (±6K tolerance)
+25°C (±7K tolerance)
+25°C (±5K tolerance)
+15°C (±5K tolerance)
+50°C (±6K tolerance)
+40°C (±7K tolerance)
Switch-on temperature
Switch-off temperature
Switch-on temperature
Switch-off temperature
+15°C (±5K tolerance)
Art. No.
+5°C (±5K tolerance)
Contact maker (NO)
+50°C (±6K tolerance)
44
Contact maker (NO)
Switch-off temperature
40°C (±7K tolerance)
+50°C (±6K tolerance)
+40°C (±7K tolerance)
Contact maker (NO)
+60°C (±6K tolerance)
+50°C (±7K tolerance)
Mechanical
Thermostat - FZK 011
•
•
•
•
•
•
Adjustable temperature
High switching capacity
Small hysteresis
Terminals easily accessible
Clip fixing
Change-over contact
The mechanical thermostat is used for controlling heating and cooling equipment, filter fans or signal devices. The thermostat registers the surrounding
air and can switch both inductive and resistive loads via snap-action contact.
Technical Data:
Switch temperature difference
4K (±1.5K tolerance)*
Sensor element
Thermostatic bimetal
Contact type
Change-over snap-action contact
Contact resistance
<10mΩ
Service life
>100,000 cycles
Max. switching capacity, NC
250VAC, 10 (4) A
120VAC, 10 (4) A
DC 30W
Max. switching capacity, NO
250VAC, 5 (2) A
120VAC, 5 (2) A
DC 30W
EMC
acc. to EN 55014-1-2, EN 61000-3-2, EN 61000-3-3
Connection
4-pole terminal, clamping torque 0.5Nm max.:
rigid wire 2.5mm2
stranded wire (with wire end ferrule) 1.5mm2
Mounting
Clip for 35mm DIN rail, EN60715
Casing
Plastic according to UL94 V-0, light grey
Dimensions
67x50x38mm
Weight
Approx. 0.1kg
Fitting position
Variable
Op/storage temp.
-20 to +80°C / -45 to +80°C
Protection type
IP20
Approvals
UL File No. E164102
Connection diagram
Enclosure heater
*Connecting terminal “N” (RF heating resistor) causes the thermal feedback to work and so reduces the switch
temperature difference to approx. 0.5K.
Heater
Thermostat FZK 011
e.g. Filter fan
for cooling
Filter fan,
Cooling equipment,
Signal device
Thermostat FZK 011 e.g. Signal device Thermostat FZK 011
Examples of connection
Art. No.
Operating voltage
Setting range
230VAC
+40 to +140°F
230VAC
+5 to +60°C
230VAC
-20 to +30°C
120VAC
+40 to +140°F
120VAC
+5 to +60°C
45
(24VDC)
Electronic
Thermostat - ET 011
•
•
•
•
•
High DC breaking capacity
Low hysteresis
Adjustable temperature
Change-over contact
Clip fixing
Electronic thermostat for regulating high performance DC 24V equipment.
Heating or cooling appliances as well as signal devices can be switched via
the potential free change-over contact. In comparison to mechanical thermostats, the ET 011 has a low hysteresis making the switchng point and setting
accuracy more precise.
Technical Data:
Switch temperature difference
Approx. 3K
Sensor element
PTC
Contact type
Change-over
Contact resistance
<10mΩ
Service life
>100,000 cycles
Max. switching capacity
28VDC, 16A
EMC
acc. to EN 55014-1-2, EN 61000-3-2, EN 61000-3-3
Connection
5-pole terminal, clamping torque 0.5Nm max.:
rigid wire 2.5mm2
stranded wire (with wire end ferrule) 1.5mm2
Mounting
Clip for 35mm DIN rail, EN60715
Casing
Plastic according to UL94 V-0, light grey
Dimensions
67x50x46mm
Weight
Approx. 80g
Fitting position
Vertical
Op/storage temp.
0 to +60°C / -45 to +80°C
Protection type
IP20
Approvals
-
Connection diagram
Thermostat ET 011
Heater
Thermostat ET 011
e.g. Filter fan
for cooling
Thermostat ET 011
e.g. Signal device
Examples of connection
Art. No.
46
Operating voltage
24VDC (20-28VDC)
Setting range
0 to +60°C
Ex FixTherm96 Thermostat
The Ex FixTherm96-Thermostats are often used as maximum thermostat in instrumentation cabinets with
• Prevention of overheating
• Temperature controlling
Features and Advantages
• Setpoints up to 135°C
• Accurate set-point (± 3°C)
• Small hysteresis
• Anodized Aluminium housing ( Stainless steel housing available)
• Armoured electrical cable standard
• Suitable for T6 and T4 classification
• Can be used for 6A / 240 VAC/DC
Technical Data:
Housing
Anodized aluminium or stainless steel
Current / voltage
6A / 240 VAC
Cable
3x 0,75 sqmm
Material cable
silicone braided cable, optional: non-braided cable
Standard length
Approx. 1 mtr
Other lengths
On request
Overall dimensions
o.d. 30mm x 49mm length
Weight
Approx. 160g
Switch
SPST
Set-point tolerance
+/-3ºC
Hysteresis
Approx. 2ºC
Mounting bracket
avaliable (B)
Ambient temp. range
-50ºC...+90ºC
EX protection class
II 2G Ex d IIC T6 or T4
II 2D Ex tD A21 IP66T
T 85ºC orT 135ºC
Certification
KEMA 01ATEX2125X and IECEx DEK 11.0017
Description
The housing is made from anodized Aluminium or Stainless Steel type 316 (on request).
When required in other applications, e.g. analyzers, it is normal practice to use our Space-heaters in combination with
these Fix-Therm96 thermostats (range from 10°C up to 135°C). The FixTherm96 can also be used for cooling purposes e.g. FixTherm TH-10/5F.
Range
Aluminium: TH-10/5 – going up with 5°C setpoints e.g. 10/5“ 15/10“ 20/15 etc. up to 135°C maximum.
Stainless Steel bodies: identical range.
47
Electrical Thermostat
Ex FixTherm96 General Purpose
SAN-GTH*/*
For Non-Hazardous areas the General Purpose FixTherm96
thermostats are very suitable. Often used as maximum thermostat in instrumentation cabinets with space heating, to
protect the equipment from overheating. Or as a minimum
thermostat with space heating to protect from freezing.
In short, temperature maintenance:
• Prevention of overheating
• Freeze protection
• Anticondensation
Technical Data:
Housing
Anodized aluminium
Current / voltage
6A / 240 VAC
Cable
3x 0,75 sqmm
Material cable
Non-braided silicone cable
Standard length
Approx. 1 mtr, other lengths optional
Overall dimensions
30mm x 58mm (diameter xH)
Weight
Approx. 160g
Switch
SPST
Set-point tolerance
+/-3ºC
Hysteresis
Approx. 2ºC
Mounting bracket
avaliable (B)
protection
IP66
Features and Advantages
•
•
•
•
•
•
Setpoints from 10°C up to 130°C
Accurate set-point - (N.C. contact)
Small hysteresis
Anodized aluminium housing (Stainless steel housing available)
Inside grounding
Can be used for 110 / 240 VAC/DC
Description
The housing is made from anodized aluminium. When required in other applications, e.g. analyzers, it is normal practice to use our Space-heaters in combination with our Fix-Therm96 thermostats (range from 10°C up to 130°C). The
FixTherm96 can also be used for cooling purposes e.g. FixTherm96 TH-10/5F (N.O. contact).
Range
GTH-10/5 - going up with 5°C each time e.g. 10/5 - 15/10 - 20-15 etc. up to 130°C maximum.
48
Mechanical
Hygrostat - MFR 012
•
•
•
•
•
Adjustable relative humidity
Change-over contact
High switching capacity
Easily accessible terminals
Clip fixing
The electromechanical hygrostat MFR 012 is designed to control enclosure
heaters so that the dew point is raised when a critical relative humidity of
65% is exceeded. In this way condensation and corrosion is effectively prevented.
Technical Data:
Switch difference*
4% RH (±3% tolerance)
Permissible air velocity
15m/sec
Contact type
Change-over contact
Contact resistance
<10mΩ
Service life
>100,000 cycles
Min. switching capacity
20V AC/DC, 100mA
Max. switching capacity
250VAC, 5 (1) A
DC 20W
EMC
acc. to EN 55014-1-2, EN 61000-3-2, EN 61000-3-3
Connection
3-pole terminal, clamping torque 0.5Nm max.:
rigid wire 2.5mm2
stranded wire (with wire end ferrule) 1.5mm2
Mounting
Clip for 35mm DIN rail, EN60715
Casing
Plastic according to UL94 V-0, light grey
Dimensions
67x50x38mm
Weight
Approx. 60g
Fitting position
Variable
Op/storage temp.
0 to +60°C / -20 to +80°C
Protection type
IP20
Approvals
UL File No. E164102
*at 50% RH.
Heater
Hygrostat
MFR 012
Hygrostat
MFR 012
Filter Fan
Enclosure heater
Filter fan,
Cooling equipment,
Signal device
Connection diagram
Examples of connection
Art. No.
32038
Setting range
35 to 95% RH
49
Electronic
Hygrostat - EFR 012
•
•
•
•
•
Adjustable and pre-set relative humidity
Optical operating display (LED)
High switching capacity
Clip fixing
Temperature-compensated
The electronic hygrostat senses the relative humidity in an enclosure with
electric/electronic components, and turns on a heater at the set point, helping prevent the formation of condensation in the enclosure. The LED integrated in the adjustment knob is lit when the connected heater is in operation.
Technical Data:
Switch difference
5% RH (±1% RH tolerance) at 25°C (50% RH)
Reaction time
Approx. 5 sec.
Contact type
Change-over contact (relay)
Service life
>50,000 cycles
Max. switching capacity (relay
output)
240VAC, 8 (1.6) A
120VAC, 8 (1.6) A
24VDC, 4A
EMC
acc. to EN 55014-1-2, EN 61000-3-2, EN 61000-3-3
Optical indicator
LED
Connection
5-pole terminal, clamping torque 0.5Nm max.:
rigid wire 2.5mm2
stranded wire (with wire end ferrule) 1.5mm2
Mounting
Clip for 35mm DIN rail, EN60715
Casing
Plastic according to UL94 V-0, light grey
Dimensions
64.5x42x38mm
Weight
Approx. 70g
Fitting position
Vertical
Op/storage temp.
0 to +60°C / -20 to +70°C
Max storage humidity
90% RH (without condensation)
Protection type
IP20
Hygrostat
EFR 012
Heater
4
Heater
Connection diagram
Example of connection
Art. No.
Operating voltage
Setting range
230VAC 50/60Hz
65% RH pre-set
120VAC, 50/60Hz
65% RH pre-set
230VAC, 50/60Hz
120VAC, 50/60Hz
50
Approvals
40 to 90% RH
VDE, (UL intended)
40 to 90% RH
UL intended
VDE; (UL intended)
UL intended
Electronic
Hygrotherm - ETF 012
•
•
•
•
Temperature and humidity adjustable
Optical operating display (LED)
High switching capacity
Clip fixing
The electronic hygrotherm senses the ambient temperature and relative
humidity in an enclosure with electric/electronic components, and turns on a
heater (or alternatively, a fan) at either set point, helping prevent the formation
of condensation in the enclosure. The LED integrated in the adjustment knob
on the active controller is lit when the connected device is in operation.
Technical Data:
Switch difference (temperature)
2K (±1K tolerance) at 25°C (50% RH)
Switch difference (humidity)
4% RH (±1% tolerance) at 25°C (50% RH)
Reaction time (humidity)
Approx. 5 sec.
Contact type
Change-over contact (relay)
Contact resistance
<10mΩ
Service life
NC >50,000 cycles
NO >100,000 cycles
Max. switching capacity (Relay
out-put)
NC 240VAC, 6 (1) A
NO 240VAC, 8 (1.6) A
NC 120VAC, 6 (1) A
NO 120VAC, 8 (1.6) A
24VDC, 4A
EMC
acc. to EN 55014-1-2, EN 61000-3-2, EN 61000-3-3
Optical indicator
LED
Connection
5-pole terminal, clamping torque 0.5Nm max.:
rigid wire 2.5mm2
stranded wire (with wire end ferrule) 1.5mm2
Mounting
Clip for 35mm DIN rail, EN60715
Casing
Plastic according to UL94 V-0, light grey
Dimensions
77x60x43mm
Weight
Approx. 0.2kg
Fitting position
Vertical
Op/storage temp.
0 to +60°C / -20 to +80°C
Protection type
IP20
Hygrotherm
ETF 012
Heater
Connection diagram
Example of connection
Art. No.
Operating voltage
Setting range
temperature
Setting range humidity
Approval
0 to +60°C
50 to 90% RH
VDE + UL FIle No. E164102
120VAC, 50/60Hz
+32 to +140°F
50 to 90% RH
UL File No. E164102
120VAC, 50/60Hz
0 to +60°C
50 to 90% RH
UL File No. E164102
230VAC, 50/60Hz
51
15°C, 25°C
Hazardous area
Thermostat - REx 011 Series
•
•
•
Compact design
Set temperature
High switching capacity
Compact small mechanical thermostat for temperature regulation and monitoring of heaters in, for example, transmitter cabinets, control panels and
measuring equipment which are deployed in areas with explosion hazard. The
special switch construction enables high response accuracy, small switch
temperature difference and a very long
service life. High switching performance allows direct control of the heaters.
Technical Data:
Explosion proof acc. to EN
LCIE (Laboratoire Central des Industries Electriques)
Conformity certificate
01 ATEX 6074/02, LCIE Nº 06 ATEX 08011, IECEx LCI 07. 0021
Sensor element
Thermostatic bimetal
Contact type (1-pole)
Opens with rising temperature
Service life
>100,000 cycles
Max. switching capacity
250VAC, 4 (1) A
Connection
Si HF - JZ 3x0.75mm2, length 1m
Mounting
mounting bracket with nut M8 (see illustration)
Casing
Aluminium, black anodised
Dimensions
length 110mm
Weight
Approx. 0.2kg
Fitting position
Variable
Op/storage temp.
-20 to +40°C / -45 to +70°C
Prot. type/ Prot. class
IP65 / I (earthed)
Aluminium
Mounting Bracket
Art. No.
52
Ex protection type
Swich-off temperature
Switch temperature difference
d IIC T6 - Ex tD A21 IP6X T85°C
+25°C (±4K tolerance)
4K (±1K tolerance)
d IIC T6 - Ex tD A21 IP6X T85°C
+15°C (±4K tolerance)
4K (±1K tolerance)
with on/off switch
Slimline
Lamp - SL 025 Series
Slim casing
Electronic ballast
Lamp without/with electrical socket (choice of sockets)
Magnet fixing (option)
Energy saving lamp
On/Off switch
Photo: Slimline lamp with on/off switch, with integrated electric socket (Germany), Art No.
•
•
•
•
•
•
The flat slimline lamp SL 025 is suitable for all types of panels and enclosures, especially where space is at a premium. The lamp can be mounted on
its narrow or broad surface using screws. It is also available with a magnet
which allows it to be fitted quickly in any position in a steel enclosure. Both
versions are available with an integrated electrical socket enabling the use of
additional appliances.
Technical Data:
Power consumption
11W (equals 75W light bulb)
Luminosity
900Lm
Lamp type
Energy saving lamp, 2G7 socket
Service life
10,000h
Switch
On/off light switch
Connection
Terminal 2.5mm2 with cable clamp, torque 0.8Nm max.
Mounting
Screw fixing, M5, 300mm centers
magnet fixing (optional)
Casing
Plastic acc. to UL94 V-0, light grey
Dimensions
345x91x40mm
Fitting position
Narrow surface/broad surface
Op/storage temp.
-20 to +50°C / -45 to +75°C
Protection type
IP20
Note
The slimline lamp SL 025 is also available with a 19” front panel
24VDC to 48VDC on request
Art. No.
Model
Operating voltage
Socket
Nominal Current
Weight
(approx)
Protection class
Approvals
without magnet
230VAC, 50/60Hz
Germany/Russia (1)
16.0A
0.4kg
I (earthed)
VDE
with magnet
230VAC, 50/60Hz
Germany/Russia (1)
16.0A
0.5kg
I (earthed)
VDE
without magnet
230VAC, 50/60Hz
F/PL/CZ/SK (2)
16.0A
0.4kg
I (earthed)
VDE
with magnet
230VAC, 50/60Hz
F/PL/CZ/SK (2)
16.0A
0.5kg
I (earthed)
VDE
without magnet
230VAC, 50/60Hz
Switzerland (3)
10.0A
0.4kg
I (earthed)
VDE
with magnet
230VAC, 50/60Hz
Switzerland (3)
10.0A
0.5kg
I (earthed)
VDE
without magnet
230VAC, 50/60Hz
UK/Ireland (4)
13.0A
0.4kg
I (earthed)
VDE
with magnet
230VAC, 50/60Hz
UK/Ireland (4)
13.0A
0.5kg
I (earthed)
VDE
without magnet
120VAC, 50/60Hz
USA/Canada (5)
15.0A
0.4kg
I (earthed)
UL File No. E234324
with magnet
120VAC, 50/60Hz
USA/Canada (5)
15.0A
0.5kg
I (earthed)
UL File No. E234324
without magnet
230VAC, 50/60Hz
none
-
0.4kg
II (double insulated)
VDE + UL File No. E234324
with magnet
230VAC, 50/60Hz
none
-
0.5kg
II (double insulated)
VDE
without magnet
120VAC, 50/60Hz
none
-
0.4kg
II (double insulated)
UL File No. E234324
with magnet
120VAC, 50/60 Hz
none
-
0.5kg
II (double insulated)
UL File No. E234324
53
with movement sensor
Slimline
•
•
•
•
•
•
Slim casing
Electronic ballast
Lamp without/with electrical socket (choice of sockets)
Magnet fixing (option)
Energy saving lamp
On/Off switch
The flat slimline lamp SL 025 with movement sensor is suitable for all types
of panels and enclosures, especially where space is at a premium. The
lamp can be mounted on its narrow or broad surface using screws. It is also
available with a magnet which allows it to be fitted quickly in any position
in a steel enclosure. Both versions are available with an integrated electrical socket enabling the use of additional appliances. The movement sensor
substitutes a door contact switch.
Photo: Slimline lamp with movement sensor and with
integrated electric socket (Germany), Art No.
Lamp - SL 025 Series
Technical Data:
Power consumption
11W (equals 75W ligth bulb)
Luminosity
900Lm
Lamp type
Energy saving lamp, 2G7 socket
Service life
10,000h
Swittch
PIR movement sensor, approx. 6min. fixed switch-on duration
Connection
Terminal 2.5mm2 with cable clamp, torque 0.8Nm max.
Mounting
Screw fixing, M5, 300mm centers
magnet fixing (optional)
Casing
Plastic acc. to UL94 V-0, light grey
Dimensions
345x91x40mm
Fitting position
Narrow surface/broad surface
Op/storage temp.
20 to +50°C / -45 to +70°C
Protection type
IP20
Note
The slimliine lamp SL 025 is also available with a 19” front panel
24VDC to 48VDC on request
The PIR movement sensor switches the lighting on when the enclosure door is opened. The switch-on timne is
reset with every further registered movement. The movement sensor does not react to mevement on the other side
of glass and so can be used in enclosures with glass doors.
Art. No.
54
Model
Operating voltage
Socket
Nominal Current
Weight
(approx)
Protection class
Approvals
without magnet
230VAC, 50/60Hz
Germany/Russia (1)
16.0A
0.4kg
I (earthed)
VDE
with magnet
230VAC, 50/60Hz
Germany/Russia (1)
16.0A
0.5kg
I (earthed)
VDE
without magnet
230VAC, 50/60Hz
F/PL/CZ/SK (2)
16.0A
0.4kg
I (earthed)
VDE
with magnet
230VAC, 50/60Hz
F/PL/CZ/SK (2)
16.0A
0.5kg
I (earthed)
VDE
without magnet
230VAC, 50/60Hz
Switzerland (3)
10.0A
0.4kg
I (earthed)
VDE
with magnet
230VAC, 50/60Hz
Switzerland (3)
10.0A
0.5kg
I (earthed)
VDE
without magnet
230VAC, 50/60Hz
UK/Ireland (4)
13.0A
0.4kg
I (earthed)
VDE
with magnet
230VAC, 50/60Hz
UK/Ireland (4)
13.0A
0.5kg
I (earthed)
VDE
without magnet
120VAC, 50/60Hz
USA/Canada (5)
15.0A
0.4kg
I (earthed)
UL File No. E234324
with magnet
120VAC, 50/60Hz
USA/Canada (5)
15.0A
0.5kg
I (earthed)
UL File No. E234324
without magnet
230VAC, 50/60Hz
none
-
0.4kg
II (double insulated)
VDE + UL File No. E234324
with magnet
230VAC, 50/60Hz
none
-
0.5kg
II (double insulated)
VDE
without magnet
120VAC, 50/60Hz
none
-
0.4kg
II (double insulated)
UL File No. E234324
with magnet
120VAC, 50/60 Hz
none
-
0.5kg
II (double insulated)
UL File No. E234324
On/off switch
Dual Lamp - DL 026 Series
Versatile - base lamp or hand lamp
Long-life energy saving lamp
Connections for further lamps
Dual lamp with on/off switch (incl. base station)
•
•
•
Technical Data:
Luminosity
1000Lm
Lamp type
Energy saving lamp, E27 socket
Service life
10,000h
Switch
On/off push switch
Connection
6-pole screw connector 2.5mm2 (torque 0.5Nm max.) for power connection,
further lamps and external door contact switch
Mounting
Screw fixing, (e.g. 35mm DIN rail)
Casing
Plastic acc. to UL94 V-0, light grey
Weight
Approx. 0.6kg
Fitting position
Variable
Op/storage temp.
-20 to +50°C / -45 to +70°C
Prot. type/prot. class
IP20 / II (double insulated)
Approvals
-
Accessories
Wall holder with connection cable (2m), hook and fixing plate
Note
120VAC and DC voltages on request
1.
2.
3.
Standard screw fixing to DIN rail
2 self-adhesive fixing plates
Wall holder with connection cable (2m), hook and self-adhesive fixing plate
By using an additional wall holder the lamp can be used as a hand lamp.
Art. No.
Operating voltage
230VAC, 50Hz
Power Consumption
20W (equals 100W light bulb)
55
Movement sensor
Dual Lamp - DL 026 Series
Versatile - base lamp or hand lamp
Long-life energy saving lamp
Automatic switching
Alternative solution for door switch
Connections for further lamps
Dual lamp with movement sensor (incl. base station)
•
•
•
•
•
Technical Data:
Luminosity
1000Lm
Lamp type
Energy saving lamp, E27 socket
Service life
10,000h
Switch
PIR movement sensor, approx. 3min. fixed switch-on duration
Connection
4-pole screw connector 2.5mm2 (torque 0.5Nm max.) for power connection
and further lamps
Mounting
Screw fixing, (e.g. 35mm DIN rail)
Casing
Plastic acc. to UL94 V-0, light grey
Weight
Approx. 0.6kg
Fitting position
Variable
Op/storage temp.
-20 to +50°C / -45 to +70°C
Prot. type/prot. class
IP20 / II (double insulated)
Approvals
-
Accessories
Wall holder with connection cable (2m), hook and fixing plate
Note
120VAC and DC voltages on request
The PIR movement sensor switches the lamp on when the enclosure door is opened. The switch-on time is reset
with every further registered movement. The movement sensor does not react to mevement on the other side of
glass and so can be used in enclosures with glass doors.
1.
2.
3.
Standard screw fixing to DIN rail
2 self-adhesive fixing plates
Wall holder with connection cable (2m), hook and self-adhesive fixing plate
By using an additional wall holder the lamp can be used as a hand lamp.
Art. No.
56
Operating voltage
230VAC, 50Hz
Power Consumption
20W (equals 100W light bulb)
With lamp holder
Hand Lamp - DL 026 Series
•
•
Long-life energy saving lamp
Versatile
Technical Data:
Luminosity
1000Lm
Lamp type
Energy saving lamp, E27 socket
Service life
10,000h
Connection
Power cable (2m) with Euro plug
Mounting
Screw or fixing plate (self-adhesive)
Casing
Plastic acc. to UL94 V-0, light grey
Weight
Approx. 0.6kg
Fitting position
Variable
Op/storage temp.
-20 to +50°C / -45 to +70°C
Prot. type/prot. class
IP20 / II (double insulated)
Approvals
-
Accessories
Lamp holder, hook and fixing plate
Note
120VAC and DC voltages on request
Art. No.
Operating voltage
230VAC, 50Hz
Power Consumption
20W (equals 100W light bulb)
57
Compact
Lamp - KL 025 Series
Magnetic or optional DIN rail mounting
Energy-saving lamp
Lamp without(with electrical socket (choice of sockets)
On/off switch
Lamp shown with protective plastic cover (see Acessories)
•
•
•
•
The compact lamp KL 025 was especially designed for use
in enclosures. A powerful magnet enables the lamp to be
mounted freely in any desired position in metal enclosures
saving time and installation problems. The integrated electrical socket allows the use of additional appliances.
Technical Data:
Luminosity
900Lm
Lamp type
Compact fluorescent lamp with integral starter
Service life
5,000h
Switch
On/off light switch
Connection
3-pole terminal 2.5mm2 with cable clamp, torque 0.8Nm max.
Mounting
Magnet fixing
Casing
Plastic, light grey
Dimensions
355x65x70mm
Weight
Approx. 1kg
Fitting position
Variable
Op/storage temp.
-20 to +50°C / -45 to +70°C
Protection type
IP20
Accessories
Lamp cover, Art. No. (see photo)
Magnet
In plastic, aluminium or stainless steel cabinets the lamp can be fixed using
screws together with inserted 35mm DIN rail sections.
Art. No.
58
Operating voltage
230VAC, 50Hz
Germany/Russia (1)
Socket
11W (equals 75W light bulb)
Power consumption
Nominal Current
Protection class
Approvals
230VAC, 50Hz
none
11W (equals 75W light bulb)
-
II (double insulated)
-
230VAC, 50Hz
F/PL/CZ/SK (2)
11W (equals 75W light bulb)
16.0A
I (earthed)
-
230VAC, 50Hz
Switzerland (3)
11W (equals 75W light bulb)
10.0A
I (earthed)
-
230VAC, 50Hz
UK/Ireland (4)
11W (equals 75W light bulb)
13.0A
I (earthed)
-
230VAC, 50Hz
Italy (6)
11W (equals 75W light bulb)
16.0A
I (earthed)
-
120VAC, 60Hz
USA/Canada (5)
9W (equals 60W light bulb)
15.0A
I (earthed)
-
120VAC, 60Hz
none
9W (equals 60W light bulb)
-
II (double insulated)
-
16.0A
I (earthed)
VDE
Electrical
Socket - SD 035 Series
•
•
•
Quickly connected
Available with or without fuse
Clip fixing
The DIN rail mounted electrical socket can be quickly fitted and connected in
enclosures allowing the use of auxiliary products such as hand lamps, measuring devices, soldering irons etc. The unit is available with and without fuse
and in many world socket standards.
Technical Data:
Connection
3 x pressure clamps for stranded and rigid wire 0.5 - 2.5mm2
Mounting
Clip for 35mm DIN rail, EN60715
Casing
Plastic acc. to UL94 V-0, light grey
Dimensions
92 x 62 x 48mm
Weight
Approx. 0.2kg
Fitting position
Variable
Op/storage temp.
-45 to +70°C
Prot. type/prot. class
IP20 / I (earthed)
Connections from mains
Art. No.
* fuse Ø 5x20mm
Operating voltage
250VAC
Germany/Russia (1)
Socket
with fuse*
Model
Nominal Current
Approvals
250VAC
Germany/Russia (1)
without fuse
16.0A
-
250VAC
F/PL/CZ/SK (2)
with fuse*
6,3A
-
250VAC
F/PL/CZ/SK (2)
without fuse
16.0A
-
250VAC
Switzerland (3)
with fuse*
6.3A
-
250VAC
Switzerland (3)
without fuse
10.0A
-
250VAC
UK/Ireland (4)
with fuse*
6.3A
-
250VAC
UK/Ireland (4)
without fuse
13.0A
-
125VAC
USA/Canada (5)
with fuse*
6.3A
UL File No. E222026
125VAC
USA/Canada (5)
without fuse
15.0A
UL File No. E222026
250VAC
Italy (6)
with fuse*
6.3A
-
250VAC
Italy (6)
without fuse
16.0A
-
6.3A
-
59
IP45/IP55
Pressure compensation
Device - DA 084
•
•
High degree of protection
Easy to install
It has become more and more important to provide a protected enclosure
environment for valuable and crucial electrical and electronical components.
In a tightly closed enclosure, pressure differentials can occur during extreme
temperature variations, such as day/night operation. When this occurs, the
risk of dust and humidity being absorbed into the control panel increases
dramatically.The specially designed pressure compensation plug DA 084 permits a controlled change in pressure. It can be installed easily in any enclosure. Because of the pressure compensation plug’s high degree of protection
(IP45), the protection type of the enclosure will not be affected.
Technical Data:
Mounting
PG29 thread with union nut
Material
Plastic acc. to UL94 V-0
Air interface
Approx. 7cm2
Dimensions
Ø65.5x30.5mm
Fitting position
Variable
Op/storage temp.
-45 to +70°C
Photo: Inside view
Installation:
Make cut-out Ø37+¹mm in enclosure wall and mount pressure compensation device with nut. Please make sure
that the sealing gasket is put in place on the outer side panel of the enclosure. For optimal pressure compensation
we recommend to use two devices on opposite sides towards the top of the enclosure.
Art. No.
60
Model
Protection type
1 packing unit
Weight (approx.)
with gasket
IP55
2 pieces
62g (31g/piece)
without gasket
IP45
2 pieces
62g (31g/piece)
IP66
Pressure compensation
Device - DA 284
•
•
•
High degree of protection
Semipermeable membrane
Easy to install
Pressure differentials in enclosures with a high degree of protection with
respect to humidity and dust are a result of inside and outside temperature
fluctuations. In case of negative pressure or vacuum, dust and humidity
can be absorbed through the door seal and can enter the enclosure. As the
humidity cannot exit the enclosure condensation may occur. The easy to
install pressure compensation device DA 284 provides the compensation of
pressure at a protection degree of IP66. A semipermeable membrane inside
the plug allows air and humidity to leave the enclosure. In the opposite direction, it only allows dry air into the enclosure while humidity and dust from the
outside are blocked by the membrane.
Technical Data:
Mounting
Thread M40 x 1.5 with nut
Depth in enclosure
Approx. 16mm
Material
Plastic, light grey
Sealing
Sealing gasket NBR
Filter
Semipermeable membrane
Air permeability
1200 l/h at a pressure difference of min. 70mbar
Dimensions
Ø60x37mm
Fitting position
Variable
Op/storage temp.
-45 to +70°C
Photo: Inside view
Installation:
Make cut-out Ø40.5+0.5mm in enclosure wall and mount pressure compensation device
with nut. Please make sure that the sealing gasket is put in place on the outer side panel
of the enclosure. For optimal pressure compensation we recommend to use two devices
on opposite sides towards the top of the enclosure.
Art. No.
Protection type
1 packing unit
Weight (approx.)
IP66 (EN 60529) / IPX9K (EN 40050-9)
1 piece
45g
IP66 (EN 60529) / IPX9K (EN 40050-9)
2 pieces
90g (45g/piece)
61
IP66
Pressure compensation
Device - DA 284
•
•
•
•
High degree of protection
Semipermeable membrane
Corrosion resistant
Food safe
Pressure differentials in enclosures with a high degree of protection with
respect to humidity and dust are a result of inside and outside temperature
fluctuations. In cas of negative pressure or vacuum, dust and humidity can
be absorbed through the door seal and can enter the enclosure. As the humidity cannot exit the enclosure condensation may occur. The easy to install
pressure compensation device DA 284 provides the compensation of pressure at a protection degree of IP66.
A semipermeable membrane inside the plug allows air and humidity to leave
the enclosure. In the opposite direction, it only allows dry air into the enclosure while humidity and dust from the outside are blocked by the membrane.
Photo: Inside view
Technical Data:
Mounting
Thread M40 x 1.5 with nut
Depth in enclosure
Approx. 9mm
Material
Stainless steel V2A (DIN 1.4404 / AISI 316L)
Sealing
Sealing gasket NBR
Filter
Semipermeable membrane
Air permeability
1200 l/h at a pressure difference of min. 70mbar
Dimensions
Ø58x31mm
Fitting position
Variable
Op/storage temp.
-45 to +70°C
Installation:
Make cut-out Ø40.5+0.5mm in enclosure wall and mount pressure compensation device with nut. Please make sure
that the sealing gasket is put in place on the outer side panel of the enclosure. For optimal pressure compensation
we recommend to use two devices on opposite sides towards the top of the enclosure.
Art. No.
62
Protection type
IP66 (EN 60529) / IPX9K (EN 40050-9)
1 packing unit
1 piece
Weight (approx.)
160g
Self-adhesive
Sanofix - Appliance Holder
Sanofix is an appliance holder for direct fixing of small appliances and perforated 35mm DIN rails.
With Sanofix small appliances can be mounted in switch cabinets significantly quicker, easier and more economically than before, without drilling holes.
Mounting DIN rails is a simple matter with Sanofix. Longer rails are mounted
on several Sanofix units and joining two rails is also not a problem.
Subsequent changes and the mounting of additional appliances can be carried out with ease - even in confined spaces.
Sanofix is a self-adhesive plastic unit with an
adhesion power which will bear a continuous load of 500g. The high-performance industrial adhesive band is also non-ageing and designed with safety
tolerances.
Technical Data:
Load
500g 24h waiting period*
Mounting
Self-adhesive (non-ageing, high-performance adhesive band)
Material
Plastic acc. to. UL94 V-0
Dimensions
43x38x14mm
Screw pitch
12.8mm; Ø3.6mm, for perforated 35mm DIN rail
Op./storage temperature
-45 to 70˚C
*Depending on the conditions of use (e.g. surface condition, size of the device to be mounted, etc.) higher loads
are possible.
Installation:
Sanofix can only be mounted on smooth surfaces, e.g. metals, lacquered surfaces and plastics (except polyethylene, polypropylene and rubber). The surfaces must be dry, free from dust, oil, separating agents and other
contamination.
Application examples:
SANOFIX
Self-adhesive surface
Protective film
Holes for screw fixing
Art. No.
1 packing unit
5 pieces
Weight (approx.)
60g (12g/piece)
63
Calculation of temperature
control in enclosures
What’s needed:
1. The dimensions of the enclosure (height, width, depth) (m)
2. The enclosure position (e.g. single enclosure, enclosure in row) according to calculation formula, enclosure surface area A (m²)
3. The enclosure material (metal, plastic) heat transfer coefficient from table, k (W/m² K)
4. The temperature difference between desired enclosure interior temperature Ti (°C) and the expected ambient temperature Tu (°C)
(e.g. day - night, summer - winter, climate zones) ∆T (K=Kelvin)
5. The stray power (self-warming) of all installed components during operation (e.g. transformers, relays, semiconductors) PV (W)
Calculation and selection of parameters: enclosure surface area - heat transfer coefficient - temperature difference
1. Enclosure surface area from dimensions
2. Enclosure position (plan view) acc. to VDE 0660 part 500
Single enclosure free on all sides
Single enclosure, wall mounted
First or last enclosure in free standing row
First or last enclosure in wall mounted row
Middle enclosure in free standing row
Middle enclosure in wall mounted row
Middle enclosure in wall mounted row with covered top
Formular for cabinet surface area A (m²)
H = height - W = width - D = depth
A = 1.8 x H x (W + D) + 1.4 x W x D
A = 1.4 x W x (H + D) + 1.8 x D x H
A = 1.4 x D x (H + W) + 1.8 x W x H
A = 1.4 x H x (W + D) + 1.4 x W x D
A = 1.8 x W x H + 1.4 x W x D + D x H
A = 1.4 x W x (H + D) + D x H
A = 1.4 x W x H + 0.7 x W x D + D x H
Example.: Enclosure free on all sides, 2000mm high / 800mm wide / 600mm deep. A = 1.8 x 2.0 x (0.8 + 0.6) + 1.4 x 0.8 x 0.6 = 5.712m²
3. Enclosure material and its heat transfer coefficient k (W/m² K)
4. Temperature difference ∆T (K=Kelvin)
Steel sheet, painted
k~5.5W/m² K
∆T = Ti - Tu
Steel sheet, stainless
k~4.5W/m² K
Aluminium
k~12W/m² K
i.e. the temperature difference between interior and exterior
Aluminium, double-walled
k~4.5W/m² K
temperatures.
Polyester
k~3.5W/m² K
Calculation formula for required heating performance (heater):
Required heating performance PH (W) = enclosure surface area A (m²) x heat transfer coefficient k (W/m² K) x temperature difference ∆T (K)
Example.:
W = 5.712m² x
5.5W/m² K
x
15K
= 471.24W
Result: Heater with 500W heating performance is required. If enclosure is situated outdoors the calculated heating performance must be
doubled!
Choose required cooling performance from diagram:
Or calculate using formula for required cooling
performance (filter fan):
Heating performance
W
Varmeydelse W
5. In case of continuous stray power PV (W)
(self-warming) this must be deducted from
the calculated heating performance.
Temperature difference ∆T
Heating
performance diagram
Varmeydelsesdiagram
Or choose required heating performance from diagram:
Skabets surface
overfladeareal
Enclosure
aream2
m²
Required air volume V (8m³/h) = installed stray power Pv(W) x air constant f* (3.3m³K/Wh)
temperature difference ∆T (K)
Example.: V = 3.3m³K/Wh = 132m³/h
x
Stray power Pv (W)
Spredningseffekt Pv (W)
600W
15K
*f(0-100)=3.1m³ K/Wh, f(100-250)=3.2m³K/Wh, f(250-500)=3.3³K/Wh,
f(500-750)=3.4m³K/Wh, f(750-1000)=3.5m³K/Wh
64
(m3/time)
AirLuftmængde
Volume (m³/h)
65
Member of the NIBE Group
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Process Heating
Heating Elements
Heating Cables
Finned Tubular
Radiators
Immersion Heaters
Church Heating
Frost Protection
Ex-Material
Oilfilled Radiators
Drum Heaters
Heating Pads
Flow Heaters
Air Duct Heaters
High-voltage
Resistors
Controllers
With more than 50 years of experience SAN Electro Heat’s most valuable asset is special knowhow about design, product development and
manufacturing of professional electrical
heating equipment for industrial use.
Denmark,
Mainoffice:
UK:
Germany:
Gillelejevej 30b
DK-3230 Graested
info@san-as.com
tel.: +45 4839 8888
fax: +45 4839 8898
Harold Comerford
H_comerford@btconnect.com
tel.: +44 1432 851999
mobile: +44 7802 853862
Wolfgang Biehs
wolfgang.biehs@nibe.de
tel.: +49 6171 887 724
mobile: +49 1622 793 484
www.san-as.com
2015 January 30th
The company is geared to deliver 100% customized products, and
thus functions both as a catalyst for a development project and as
supplier of the final product. At the same time we insure and maintain
the required quality level, mechanical and electrical dimensioning,
approvals and documentation.