MB■ 2610TRIPLE
BALANCE
BEAM
0PERATING丨 NsTRUCT10Ns
MB■ 2610TRIPLE
zeroIng:
BEAM BALANCE
FOr exact zero, adjust the knurled knob which is
Iocated atthe Ieft end ofthe beam "is advisable to check
oPERATlNG lNsTRUCTIONs
the zero adjustment periodica"y
Weigh∶ ng:
P!ace the specimen on the center ofthe platforΠ ηand proceed as
Degaussed
Meta|Pa1forms
fo"oWs∶
怡
早Ⅱ
龀叠糌 淞描 V
z∶
1
Starting with the largest capac"y beam(500g),move the500g
poise to the right to the first notch which Caused the pointer to drop,
:晷
then,m ove"back one notch,causing the pointerto rise
2. Repeat procedure vvith100g poise
3. s"de the10g poise to the pos"ion that brings the pointer to
rest at zero
The vveight ofthe specimen is the sum ofthe values of a"poise
pos"ions,read direCuy from the graduated beams
Adjus1Knob
Attachment weights:
Bs
aιse
ca
铷Me
TotaI capacity is either2610grams or5 pounds, 2
ounces when attachment vveights are suspended from the
ρiVots Without the weights,the Capacity is610grams(1
ρound,2ounces)
Care and rnaintenance:
Construction and AppⅡ cation
Keep the balance clean at a"times N刂 ost dirt or foreign matter
can eas"y be removed w"h an air syringe, but a piece of adhesivebacked taρ e pressed againstthe magnetfaces vvi"keep them free from
a"oy and the plane is of agate vvhich Can improve accuracy of use and
dirt Never apply lubriCants to the knives or bearings and donIt a"ovv
dirt or foreign materials to accumu丨 ate on any part ofthe beam The
The“ KILPOTECH” MB¨ 2610singIe-Pan BaIance is of unequal
arm type w"h three beams The beam is rnade ofhigh qua"ty aluminum
m甘 异
:〖 ;1胛 ri丨
svvIngs
t∶ P‰
品J样
g卩
rT甜
t甘
%J〖
扌
黼 黼1‰ m%:路
Beam must be kept clean in order to provide years of aCcurate stable
readings
lt is WideIy su"able for physica卜 Chenη istry experiments and
analyticaIvveighting in chemical works,rnedical and hygiene,foodˉ stuff,
agricu"ure,textiIes,eIectronics,mines,scientific research institutions,
univers"ies and co"eges,etc
gh弘
邑γ 々⒈占T:涅
l18:g|alf%:‰
佴
i∶
:T舀 fr嚣 毖
凇
:恕
lodged underneath the p丨 atform,and one rubber washerlocated above
the pointer The washes areto be removed from the scaIe
set■ up:
After placing the balance on a smooth,flat surface,s"de each
separate poise(s"ding weight)int° it:s zero slot With a"poises at the
zero pos"ion,the pointer should be near zero
Capacity:
W"hout attachment weights∶ 610g
WⅡ h included attachment weights∶ 2610g
Unpacking:
⒃
specifications
Readab"ity:o1g
Weighting units:grams
Beam CaIibrations:1oc× 01g,1oo× 10g,5oo× 1oog
Features:
Three beam directreading
Attachment Weights incIuded
Magnetic Damping system
TroubIeshooting:
Before troubIeshooting please take these words of “BaIanCe Beam
llVisdom” BaIance Beams are a very oId and basic design of scale They
date back to the ancient Egyptian Empire and BaIance Beam scaIes were
used to bu"d the pyramids Thus,the design is quite simple-a cup(hidden on
modern beam scales)nlled wⅡ h metsHoose weights and some metsl sliding
weights Therefore to fiX a Balance Beanη
scale requires very basic stepsˉ
such as adding/removing weightfrom the cup orusing a wrench to rnake the
beam operate smoothly(if itis touChing or rubbing as " operates,)Firs1
before troubIeshooung be cedsin thatyou have correCuy unpacked the scale
and removed a"rubber stoppers(you’ d be surρ
"seda"attheir
how many proper
tirnes zER0
this
happens)Also be sure thatthe sⅡ ding weights are
pos"ion Please be100o/。 sure that you have removed both rubber stoppers
and a"packing bands/materials
1)“
The scaIe WonIt zero” ∶sometimes in transport the beam
Will some how become unbalanced This means adjusting the zero
knob doesn’ t make the scale zero properIy lf this hapρ ens to your
scaIe please know that you can manua"y add or remove weightto the
“
Balance Cup” The Balance cup is located underneath the round
metal tray SimpIy sρ in the tray off(counterclockwise)to access the
BaIance Cuρ and add orremove weightas fo"ows:
If your scale wouId not zero because "was reading too "ght
(meaning you would have had to press down on thetrayto make"zero)
Then add a sma"amount of weightto the Cup(just a coin or paperc"p,
you Can add orremove weightas you require).
If your scale would not zero because it was reading too heavy
(meaning you would have had to ρu"up on the tray to make it zero),
then remove a sma"amount of weIghtfrom the cup uustremove a tiny
amount,you can remove oradd weightas you require)
lf you are trying to compensate for a sma"bowl ortray,you Can
remove weightfrom the Cup untilthe scale zeros The Balance Beam is
very basic scale and ifit zeros&moves freely Then it always reads
accurately
2)“ The
Beam is Rubbing`Touching”
∶ln order forthis sCa丨 e to
work proρ eHy, it must operate smoothly w"hout touching or rubbing
Sometimes in transportthe beam wi"get shifted and touch the internal
magnets by the frontifthe beam(where the
“
0” indicator is) lf this
hapρ ens pIease try to manua"y adjustthe bean1using a wrench on the
main bo"under the scale simpIy twist the beam to make it operate
smoothly If you Cannot make the beanη operate smoothly then