Rodless Cylinders Switches Catalog 0953 Magnetic Switches Type RS In the type RS contact is made by a mechanical reed switch encapsulated in glass. Direct connection with 2-pole cable, 5 m long, open ended (Type RS-K). Type ES In the type ES contact is made by an electronic switch – without bounce or wear and protected from pole reversal. The output is short circuit proof and insensitive to shocks and vibrations. Connection is by 3-pole connector for easy disconnection. Fitted with connection cable 100 mm long with connector. A 5 m cable with connector and open end can be ordered separatly, or use the Order No. for the complete Type ES with 5 m cable. Electrical Connection, Type RS Magnetic Switches RS and ES Electrical Service Life Protective Measures Magnetic switches are sensitive to excessive currents and inductions. With high switching frequencies and inductive loads such as relays, solenoid valves or lifting magnets, service life will be greatly reduced. and lifting magnets, voltage peaks (transients) are generated which must be suppressed by protective diodes, RC loops or varistors. Connection Examples Load with protective circuits (a) Protective resistor for light bulb (b) Freewheel diode on inductivity (c) Varistor on inductivity (d) RC element on inductivity !)BD* ,!)ED* With resistive and capacitative loads with high switch-on current, such as light bulbs, a protective resistor should be fitted. This also applies to long cable lengths and voltages over 100 V. )b* )c* )d* For the type ES, external protective circuits are not normally needed. In the switching of inductive loads such as relays, solenoid valves Dimensions (mm) – Type RS-K Normally closed (NC) brown(bn) 7 ~ 5000 * blue (bu) 21-5 MFE Normally open (NO) TX2-6 41 brown(bn) blue (bu) * Length with possible minus tolerance, see chart below MFE Electrical Connection, Type ES Dimensions (mm) – Type ES-S Standard Version: Type PNP MFE QOQ brown (bn) 2 black (bk) out 5 blue (bu) 4 , Optional Version Type NPN MFE OQO 4 (Out) , 2 brown (bn) black (bk) out 5 blue (bu) 4 PIN assignment (view of pins) according to DIN EN 50044 1 (+) 3 (-) * Length with possible minus tolerance, see chart below Length of connection cable with length tolerance Magnetic Switch Order No. Nominal cable length Length tolerance KL3045 5000 mm – 50 mm KL3048 100 mm – 20 mm 10750 5000 mm – 50 mm 10751 145 mm p 5 mm 27 O RIG A )e* !)BD* !)ED* Parker Hannifin Corporation Parker-Origa Glendale Heights, Illinois www.parkeroriga.com Rodless Cylinders Switches Catalog 0953 Magnetic Switches Type RST Magnetic Switches RST and EST such as relays, solenoid valves and lifting magnets, voltage peaks (transients) are generated which must be suppressed by protective diodes, RC loops or varistors. Electrical Service Life Protective Measures Magnetic switches are sensitive to excessive currents and inductions. With high switching frequencies and inductive loads such as relays, solenoid valves or lifting magnets, service life will be greatly reduced. Connection Examples Load with protective circuits (a) Protective resistor for light bulb (b) Freewheel diode on inductivity (c) Varistor on inductivity (d) RC element on inductivity Type ES with 5 m cable. In the type RST contact is made by a mechanical reed switch encapsulated in glass. Type EST In the type EST contact is made by an electronic switch – without bounce or wear and protected from pole reversal. The output is short circuit proof and insensitive to shocks and vibrations. Connection is by 3-pole connector for easy disconnection. Fitted with connection cable 100 mm long with connector. A 5 m cable with connector and open end can be ordered separately, or use the Order No. for the complete Electrical Connection Type RST-K Normally closed brown (bn) blue (bu) With resistive and capacitative loads with high switch-on current, such as light bulbs, a protective resistor should be fitted. This also applies to long cable lengths and voltages over 100 V. )b* )c* )d* )e* !)BD* !)ED* For the type EST, external protective circuits are not normally needed. In the switching of inductive loads Electrical Connection Type EST-K ,!0!. BD!0!ED .!0!, brown (bn) black (bk) blue (bu) , ED . Normally open brown (bn) blue (bu) ,!0!. BD!0!ED .!0!, Electrical Connection Type RST-S brown (bn) 2 blue (bu) 5 !)BD* ,!)ED* Electrical Connection Type EST-S ,!0!. BD!0!ED .!0!, brown (bn) 2 black (bk) 5 blue (bu) 4 28 O RIG A , ED . Parker Hannifin Corporation Parker-Origa Glendale Heights, Illinois www.parkeroriga.com Rodless Cylinders Switches Catalog 0953 Magnetic Switches – Dimensions Dimensions (mm) – Type RST-K, EST-K * M3 SW 1,5 6,1 30,5 4,3 2,9 ** 42 * Cable lengths available: 5000 mm ± 75 mm 2000 mm ± 40 mm ** Switching point: Type RST-K Normally closed Type RST-K Normally open Type EST-K Normally open 14 mm 12.3 mm 8.1 mm Dimensions (mm) – Type RST-S, EST-S Screw connector 30,5 29-37 Snap connector * ± 6 mm ** Switching point: Type RST-K Normally closed Type RST-K Normally open Type EST-K Normally open bn / bn Installation bl / bu bn / bn Insert bl / bu magnetic switch 4 (out) M8x1 ** 6,1 4,3 2,9 M3 SW 1,5 36-40 M8x1 240 * 1(+) 14 mm 12.3 mm 8.1 mm +/AC / DC -/+ 3(-) PIN assignment (view of pins) to DIN EN 50044 Dimensions of Adapter for Magnetic Switch Rotate + / - Secure DC magneticAC / magnetic switch - / + switch Insert magnetic switch into adapter Insert adapter into cylinder dovetail slot mark for switching point Tighten screw: torque 1.5 Nm Ordering Information SW = 1.5 mm 29 O RIG A Type Voltage Order No. RST-K 10-30V AC/DC KL3300 EST-S 10-30V DC KL3312 Parker Hannifin Corporation Parker-Origa Glendale Heights, Illinois www.parkeroriga.com