Small Use Mark w/ TS Tagline
Mark width standardized at 1.0” but can
vary from 1.0” up to 2.25”. TS Tagline scales
proportionally.
Mark should never fall below 1.0”
thinking sound
self-powered + low-voltage
a no-compromise solution for premium audio installations
Regul
Mark
but ca
TS Tag
compact, self-powered systems
with remote low-voltage power supplies
exclusively from Meyer Sound
High-performance audio. Low-voltage installation. Together for the first time.
For AV installations demanding the utmost in audio quality, Meyer Sound offers an innovative solution: low-voltage,
self-powered systems. This exclusive technology opens up a broad range of options for system designers, consultants,
integrators and contractors.
As with conventional constant-voltage solutions, these new systems can be installed without conduit*, but the loudspeakers
operate on DC power from a remote rack-mount power supply, so there is no need for AC mains service—requiring Class 1
electrical conduit—at each loudspeaker location. The amplifier and signal-processing circuits store DC power for peak
demands, allowing the flexibility of lengthy cable runs (without conduits) while preserving the advantages of self-powered
systems. Power and balanced audio are carried on a single multi-conductor cable terminated by a 5-pin connector. As a
result, installation times and costs are reduced compared to those of conventional constant-voltage systems.
However, the audio performance is beyond comparison. In any application—from foreground music in an intimate restaurant
to auxiliary systems in large performance halls—the audible superiority of Meyer Sound self-powered technology will be
noticed, and appreciated.
*
In North America, electrical codes identify low voltage and low current electrical wiring methods as Class 2. Europe has also adopted a unified safety standard that
identifies a low voltage and low current electrical wiring as Protective Extra Low Voltage (PELV).
significant performance and
logistical benefits over
constant-voltage systems
PRODUCT BASICS
Self-powered Systems: Clear Advantages
All Meyer Sound self-powered systems offer clear advantages over conventional solutions—whether constant-voltage or lowimpedance (2–16 ohm)—that require separate amplifiers and loudspeakers.
Superior performance. Amplifiers and processing are ideally
matched to each driver, with no long speaker cables or transformers in between to drain power, limit bandwidth or add distortion.
Enhanced intelligibility. Low distortion combined with flat
frequency and phase response reduces listener fatigue and
also satisfies the STI requirements for emergency voice
alarm applications.
Consistency and quality. All Meyer Sound products, transducers included, are manufactured at our headquarters according
to strict quality-control processes, enabling a level of product
consistency unparalleled in the industry.
At-a-glance loudspeaker monitoring.* Meyer Sound’s
Compass RMS™ remote monitoring system tracks input level,
voltage and DC current for each loudspeaker, a feature that can-
No amplifier racks. Equipment rooms can be smaller, with
reduced cooling requirements.
not be implemented in constant-voltage systems.
Improved reliability. Amplifiers, processing and circuit protection are all integrated, preventing potential damage from
improper configuration or operator misuse.
er can receive a different program signal, with levels and EQ pre-
*
Optional in selected loudspeakers and subwoofers.
Each loudspeaker individually addressable. Each loudspeakcisely set for specific location. Systems are more easily zoned,
allowing exceptional flexibility in multi-purpose meeting facilities.
Low-Voltage Self-Powered: Visualize the advantages.
All the advantages of self-powered systems remain, including superior audio performance and the flexibility of sending separate
programs to each loudspeaker. What you give up are the amp racks (and extra cooling) as well as long speaker cable runs or
Class 1 wiring conduits.
Galileo
loudspeaker
management system
Compass RMS
network cable
to RMServer
MPS-488HP
external power supply
MM-10XP
subwoofer
UP-4XP
loudspeakers
Sleeve Color
Cable Type
Red
48V DC power: DC (–), DC (+)
Green
Balanced audio, line level: audio chassis, audio (–), audio (+)
Magenta
48V DC power and balanced audio (composite): DC (–),
DC (+), audio chassis, audio (–), audio (+)
Gray
Compass RMS remote monitoring system: twisted pair
Black
100-250V AC, 50/60 Hz: line/neutral, earth
(for MPS-488HP and Galileo 616)
MM-4XP
loudspeakers
HMS-10
loudspeaker
UP-4XP
loudspeaker
Low-voltage self-powered? Or conventional constant-voltage? Points to consider.
Some installation scenarios previously dictated a constant-voltage solution, even though doing so inevitably compromised audio
performance. These were normally installations with multiple loudspeaker locations, considerable distance between equipment
rooms and loudspeaker locations, and no readily available AC power connections at all loudspeaker locations.
Now Meyer Sound’s low-voltage systems offer a new solution that combines the best of both worlds. The cost-savings of Class 2
wiring are retained, but with significant benefits compared to conventional constant-voltage solutions.
Lower distortion and wider bandwidth for significantly
better music quality and voice intelligibility.
Higher SPL output for more headroom and greater throw
distance. In many installations, this translates into fewer
loudspeakers and more pleasant aesthetics.
Tighter, more powerful bass response down to 25 Hz with
the UMS-1XP subwoofer.
Flatter frequency and phase response for more consistent
performance and easier tuning of high-performance, multiloudspeaker installations.
Greater power/performance-to-size ratio with no
transformer and line losses between amplifier and speaker.
for the architect’s eye
and the music lover’s ear
Visibly attractive. Visibility optional.
Meyer Sound low-voltage installation loudspeakers are delightfully discreet. When surface mounted using the adjustable
U-bracket, the sleek cabinets complement any elegant décor. Custom colors help integrators deliver quality sound while
meeting challenging aesthetic requirements.
Applications
•
AV playback systems for museums, trade show exhibits and corporate presentations.
•
Foreground music and PA auxiliary systems for bars, restaurants, nightclubs, retail outlets, and cruise ships.
•
Compact PA systems for meeting rooms.
•
Front, underbalcony and spot fill in theatres, concert halls and places of worship.
UPJ-1XP
UPJ-1XP 48V DC compact Vari O Loudspeaker
The UPJ-1XP is the most powerful model in Meyer Sound’s low-voltage series,
48V DC compact VariO
loudspeaker
Operating Frequency Range1
55 Hz–20 kHz
Maximum peak SPL2
128 dB
Weight
43 lbs (19.5 kg)
Dimensions
11.15” w x 22.43” h x 12.25” d
(283 mm x 570 mm x 311 mm)
providing a robust 128 dB peak SPL with extended low frequency response down to
55 Hz. A neodymium magnet 10-inch low/mid cone driver works in tandem with a
3-inch compression driver coupled to a rotatable 80° by 50° VariO™ horn. An onboard, 2-channel Class D amplifier delivers 300 W of total burst power. The UPJ-1XP
uniquely combines high acoustic output, uncompromising sonic performance, and
the installation ease of low-voltage wiring. A variety of flying, mounting and weather
protection options make the UPJ-1XP ideally suited to a wide range of indoor and
outdoor applications.
Notes
1
Recommended maximum operating frequency range. Response depends on loading conditions and room acoustics. 2Measured with music referred to 1 meter.
UPJunior-XP
UPJunior-XP 48V DC Ultracompact Vari O Loudspeaker
UPJunior-XP features versatile rigging, an extraordinary power-to-size ratio, and
48V DC ultracompact VariO
loudspeaker
Operating Frequency Range1
70 Hz–20 kHz
Maximum peak SPL2
126 dB
Weight
26 lbs (11.8 kg)
Dimensions
9.00” w x 19.04” h x 10.20” d
(229 mm x 484 mm x 259 mm)
a VariO horn which allows quick rotation to provide an 80° by 50° coverage pattern
with either horizontal or vertical orientation. The low/mid-frequency section employs
an 8-inch neodymium magnet cone driver, while the high-frequency section utilizes
an efficient 0.75-inch exit, 2-inch diaphragm compression driver. The discreet profile
belies the system’s power: it can produce a maximum peak output of 126 dB SPL
at one meter over its wide operating frequency range of 70 Hz to 20 kHz. A host of
mounting and arraying options make UPJunior-XP a versatile performer in a broad
range of applications.
Notes
1
Recommended maximum operating frequency range. Response depends on loading conditions and room acoustics. 2Measured with music referred to 1 meter.
UPM-1XP
UPM-2XP
UPM-1XP and UPM-2XP 48V DC UltraCompact Loudspeaker
The low-voltage version of the award-winning compact loudspeaker, the UPM-1XP is a
48V DC ultracompact
wide-coverage
loudspeaker
48V DC ultracompact
narrow-coverage
loudspeaker
Operating Frequency Range1
UPM-1XP: 75 Hz–20 kHz
UPM-2XP: 80 Hz–20 kHz
Maximum peak SPL2
123 dB
Weight
17 lbs (7.7 kg)
Dimensions
6.85” w x 18.00” h x 7.70” d
(174 mm x 457 mm x 196 mm)
bi-amplified, three-way system capable of high sound pressure levels with low distortion
and uniform directional control. High-frequency reproduction is provided by a 1-inch
metal dome driver via a 100° symmetrical waveguide, while low-mid range is handled
by two 5-inch cone transducers. Both cone drivers work in parallel for low frequency
power, with one rolling off above 320 Hz to maintain uniform directionality through the
crossover region. The UPM-1XP drivers, manufactured in-house by Meyer Sound,
are powered by a three-channel power amplification module (350 W total) that also
incorporates an active crossover, driver protection, and frequency and phase correction
circuitry. The UPM-2XP has a narrower 45° symmetrical pattern but is otherwise identical.
Notes
1
Recommended maximum operating frequency range. Response depends on loading conditions and room acoustics. 2Measured with music referred to 1 meter.
UMS-1XP
UMS-1XP 48V DC UltraCompact Subwoofer
The externally powered UMS-1XP is an extremely compact subwoofer that provides
48V DC ultracompact subwoofer
Operating Frequency Range1
25 Hz–160 Hz
Maximum peak SPL2
127 dB
Weight
58 lbs (26.3 kg)
powerful low-frequency extension and is a logical companion to the UPM‑1XP
ultracompact, wide coverage loudspeaker and UPJunior‑XP ultracompact VariO
loudspeaker. For installations requiring even greater low-frequency output, multiple
UMS‑1XPs can be stacked. The UMS-1XP is loaded with twin 10-inch cone drivers
driven by a dual-channel Class D amplifier with 450 W of total peak power.
Dimensions
22.75” w x 16.3” h x 17.51” d
(578 mm x 414 mm x 445 mm)
Notes
1
Recommended maximum operating frequency range. Response depends on loading conditions and room acoustics. 2Measured with music referred to 1 meter.
UP-4XP
UP-4XP UltraCompact Loudspeaker
The UP-4XP is ideal for applications requiring an inconspicuous cabinet that delivers
high sound pressure levels, low distortion, and uniform directional control. The highultracompact loudspeaker
frequency section includes a 1-inch metal dome tweeter on a 100˚ constant directivity
horn. The low/ mid-frequency section comprises two 4-inch cone transducers that
Operating Frequency Range1
66 Hz–18 kHz
Maximum peak SPL2
121 dB
Weight
12.2 lbs (5.53 kg)
Dimensions
13.84” w x 5.54” h x 5.25” d
(352 mm x 141 mm x 133 mm)
work in parallel at low frequencies— delivering a combined acoustic output—with one
of the drivers rolling off at higher frequencies to prevent interference in the crossover
region. The UP-4XP drivers, manufactured in-house by Meyer Sound, are powered by a
three-channel power amplification module (500 W total) that also incorporates an active
crossover, driver protection, and frequency and phase correction circuitry. QuickFly
mounting options to facilitate overhead and wall mounting include the MUB-UP4
U-bracket and MYA-UP4 cradle-style yoke. Custom colors are also available.
Notes
1
Recommended maximum operating frequency range. Response depends on loading conditions and room acoustics. 2Measured with music referred to 1 meter.
MM-4XP
MM-4XPD
MM-4XP Self-powered Miniature Loudspeaker
Housed in a compact enclosure with a faceplate only four inches square, the MM-4XP
is ideal for installations where space is limited and visibility is a concern. With its wide
self-powered
miniature loudspeaker
directional miniature
self-powered loudspeaker
Operating Frequency Range1
120 Hz–18 kHz
Maximum peak SPL2
113 dB
Weight
MM-4XP: 4.2 lbs (1.91 kg)
MM-4XPD: 5.2 lbs (2.36 kg)
Dimensions
MM-4XP: 4.04” w x 4.04” h x 5.72” d
(103 mm x 103 mm x 145 mm)
MM-4XPD: 4.04” w x 4.04” h x 7.95” d
(103 mm x 103 mm x 202 mm)
frequency response, ultra-low distortion and astonishing SPL-to-size ratio, the MM-4XP
is a standout performer in both speech and music applications. The integrated 220 W
Class D amplifier forcefully drives a 4-inch cone transducer, while peak and RMS limiters
regulate driver excursion to maintain exemplary performance even when driven into
overload. The MM-4XPV version includes a volume control on the top panel.
MM-4XPD Directional Miniature Self-powered Loudspeaker
The MM-4XPD provides a unique solution for reverberant spaces. Similar to the MM-4XP,
it features patent-pending technology to create a hypercardioid directional pattern with
rear attenuation in the order of 10 dB, even at the lowest reproduced frequencies.
Notes
1
Recommended maximum operating frequency range. Response depends on loading conditions and room acoustics. 2Measured with music referred to 1 meter.
MM-10XP Miniature Subwoofer
MM-10XP
As a companion to MM-4XP and UP-4XP compact loudspeakers, the MM-10XP
subwoofer allows system designers to create full-range systems in small spaces. The
cabinet houses a single 10-inch driver and a single-channel power amplifier complete with
onboard processing driver protection, and frequency and phase correction. The built-in
miniature subwoofer
Operating Frequency Range1
33 Hz–228 Hz
Maximum peak SPL2
123 dB
Weight
26.7 lbs (12.11 kg)
Dimensions
19” w x 11” h x 12” d
(482 mm x 279 mm x 305 mm)
crossover accepts full-range signals, facilitating basic daisy-chaining for signal distribution.
In addition to the low-voltage MM-10XP version, two more versions are offered. The
MM-10AC* and MM-10ACX* subwoofer models include internal power supplies, XLR
audio inputs, and locking PowerCon connectors for AC input and looping output
(for powering additional units). The MM-10AC also includes a male XLR output for
daisy-chaining audio signals, while the MM-10ACX includes onboard DC power and
audio routing for driving a pair of MM-4XP miniature loudspeakers or a single UP-4XP
ultracompact loudspeaker.
*Not compatible with Compass RMS.
Notes
1
Recommended maximum operating frequency range. Response depends on loading conditions and room acoustics. 2Measured with music referred to 1 meter.
CH 1
CH 2
CH 3
CH 4
VOLTAGE
CH 5
CH 6
CH 7
CH 8
LOAD
CURRENT
MPS-488HPe
48VDC Power Supply
LINK
IN 1
IN 2
IN 3
IN 4
IN 5
IN 6
IN 7
IN 8
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
OUT 2
48VDC
AUDIO
+
+
s
OUT 4
48VDC
AUDIO
+
+
s
OUT 8
OUT 6
48VDC
48VDC
AUDIO
+
+
AC INPUT
100--240V~
AUDIO
+
+
s
s
AUDIO
1 GND
2 +
3 --
48VDC
AUDIO
+
+
OUT 1
48VDC
AUDIO
+
+
s
s
OUT 3
48VDC
AUDIO
+
+
s
OUT 5
48VDC
AUDIO
+
+
s
OUT 7
MPS-488HP Power Supply
50-60 Hz 830W MAX
The MPS-488HP power supply is designed for installations with multiple low
voltage 48V loudspeakers. It receives eight channels of balanced audio from
MPS-488HPe
XLR-F inputs and routes the audio, along with 48V DC power, to the eight output
48V power supply with
EN3 connectors
channels. Output connectors are either Phoenix 5-pin or Switchcraft EN3 5-pin.
CH 1
CH 2
CH 3
CH 4
VOLTAGE
CH 5
CH 6
CH 7
CH 8
LOAD
CURRENT
MPS-488HPp
48VDC Power Supply
LINK
IN 1
IN 2
IN 3
IN 4
IN 5
IN 6
IN 7
IN 8
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
NOTE: NEC ANSI/NFPA 70
OUT 1
OUT 2
OUT 3
Class 2 Wiring may be used
OUT 4
OUT 5
OUT 6
OUT 7
OUT 8
One MPS-488HP can power up to eight 48V DC powered loudspeakers.
AC INPUT
100--240V~
AUDIO
+
--
AUDIO
1 GND
2 +
3 --
S
+
-48 VDC
EACH OUTPUT: 48VDC 96VA MAX.
WARNING: Risk of Fire or Electric Shock. Do not interconnect output terminations.
60 Hz 830W MAX
When equipped with the RMS option, the MPS-488HP allows real-time
monitoring of 48V DC loudspeakers via Meyer Sound’s Compass RMS remote
MPS-488HPp
monitoring system.
48V power supply with
Phoenix connectors
MPS-481 Power Supply
The MPS-481 is designed exclusively for powering a single MM-4XP loudspeaker
(any version).
MPS-481
MM-4XP 48V power supply
HMS 48V Surround Loudspeakers
The three low-voltage, self-powered loudspeakers in Meyer Sound’s HMS family were originally designed and engineered
to achieve unprecedented linearity and consistency in cinema surround applications. However, the HMS trio’s unique
combination of self-powering, wide symmetrical horns and sleek angled enclosures also make them adaptable to a wider
range of critical-quality installed sound applications. With a wide range of yoke- and wall-mounting options, HMS family
loudspeakers are equally adaptable to demanding requirements in theatres, houses of worship, rehearsal studios, as well as
in many larger hospitality and retail locations. HMS family loudspeakers utilize the same MPS-488HP power supply as the
other low-voltage loudspeakers in prior pages.
In both film exhibition and post-production applications, HMS family loudspeakers adhere to the rigorous standards of
Meyer Sound EXP Cinema Sound systems.
HMS-5
HMS-10
HMS-12
compact surround
loudspeaker
surround loudspeaker
high-power surround
loudspeaker
Operating Frequency Range1
55 Hz –18 kHz
Operating Frequency Range1
55 Hz –18 kHz
Operating Frequency Range1
59 Hz –18 kHz
Maximum peak SPL2
123 dB
Maximum peak SPL2
126 dB
Maximum peak SPL2
130 dB
COVERAGE
80˚ symmetrical
COVERAGE
80˚ symmetrical
COVERAGE
100˚ symmetrical
Weight
19.6 lbs (8.89 kg)
Weight
29.1 lbs (13.2 kg)
Weight
46.0 lbs (20.87 kg)
Dimensions
15.0” w x 12.0” h x 9.7” d
(381 mm x 305 mm x 246 mm)
Dimensions
15.50” w x 19.50” h x 12.48” d
(394 mm x 495 mm x 317 mm)
Dimensions
16.80” w x 25.12” h x 9.78” d
(427 mm x 638 mm x 248 mm)
Notes
1
Recommended maximum operating frequency range. Response depends on loading conditions and room acoustics. 2Measured with music referred to 1 meter.
Connectors and Wiring
Meyer Sound low-voltage loudspeakers offer several different connector options. All can be ordered with Phoenix 5-pin plug-in
connectors for quick, secure connection in any installation. In addition, many of the loudspeakers— those likely to be used in
theatrical and corporate AV applications— may be ordered with the rugged EN3 circular 5-pin connector.
The larger and more powerful loudspeakers— those well suited to outdoor applications in theme parks, themed spectaculars and
open-air hospitality installations— also offer the robust and environmentally sealed and locking ECO-M 7-pin connector. When ordered
in conjunction with the full weather protection option the ECO-M connector allows permanent installation in exposed outdoor locations.
Model
Phoenix 5-Pin
EN3 5-Pin
ECO-M 7-Pin
UPJ-1XP, UPJunior-XP, UPM-1XP, UPM-2XP, UMS-1XP
P
P
P
UP-4XP, MM-10XP, MPS-488HP
P
P
HMS-5, HMS-10, HMS-12
P
MM-4XP, MM-4XPD, MM-4XPV
P
All low-voltage loudspeakers may be wired with a single 5-conductor cable such as Belden® 1502). For longer cable runs,
particularly for larger and more powerful loudspeakers, two cables may be wired to the same connector: a larger gauge,
2-conductor cable for the DC power and a smaller gauge 3-conductor cable for the balanced audio.
COMPASS RMS Remote Monitoring System
COMPASS RMS
The Compass RMS remote monitoring system provides at-a-glance monitoring of complex loudspeaker systems on a remote Windows or Mac computer,
allowing an operator to evaluate overall performance and quickly identify
potential problems. Compass RMS tracks input level, voltage and DC current
for each loudspeaker, and also enables selective loudspeaker muting. In 48V
systems, individual loudspeakers are integrated into the RMS network via an
MPS-488HP power supply equipped with the RMS option. The RMS module
in the MPS-488HP connects to an RMServer, which integrates external control and notification (such as fire mute) and is programmable to provide e-mail
software interface
fault notifications even when no control computer is connected. The RMS
tab of the Compass software gives a clear graphic display of system status,
enabling comprehensive supervision by personnel at all levels.
Stella-8C
Stella-8C 18V DC Ceiling Mount Installation Loudspeaker
18V DC ceiling mount
installation loudspeaker
Stella-8C is a self-powered, two-way loudspeaker designed for the utmost performance
in ceiling-mount applications. Incorporating an 8-inch cone and coaxial 0.75-inch
HF driver, Stella-8C can produce high sound pressure levels while maintaining
Operating Frequency Range1
100 Hz–22 kHz
Maximum peak SPL2
117 dB
Weight
9.0 lbs (4.1 kg)
Dimensions
11.66” dia. (front) x 5.47” d
(296 mm x 139 mm)
extraordinarily flat frequency and phase response. Clarity, balance and tonal depth
far exceed what is possible from conventional 70V ceiling speakers. Housed in an
aluminum die-case enclosure with integral heat sink, Stella-8C can be flush-mounted
in standard backboxes for 8-inch loudspeakers (minimum depth 6.5 inches). 18V DC
power and balanced audio are supplied over a single cable, terminated by a 5-pole
Phoenix connector. Available in white, black or custom colors.
Notes
1
Recommended maximum operating frequency range. Response depends on loading conditions and room acoustics. 2Measured with music referred to 1 meter.
Stella-4C
Stella-4C 18V DC Ceiling Mount Installation Loudspeaker
Stella-4C shares the same design as the larger Stella-8C, but in a smaller package for
18V DC ceiling mount
installation loudspeaker
applications with reduced space and slightly lower power requirements.
Stella-188 Power Supply
Operating Frequency Range1
100 Hz–22 kHz
Maximum peak SPL2
108 dB
Weight
6.0 lbs (2.72 kg)
Dimensions
11.75” dia. (front) x 4.00” d
(298 mm x 102 mm)
The Stella-188 is a rack-mount 18V DC external power supply designed specifically for
use with the Stella series of low-voltage self-powered loudspeakers. One Stella-188
supplies power and balanced audio signal for up to eight Stella-8C or 16 Stella-4C
loudspeakers. Cable runs of up to 150 feet are possible (using AWG 18 wire) with
negligible loss of peak SPL.
Notes
1
Recommended maximum operating frequency range. Response depends on loading conditions and room acoustics. 2Measured with music referred to 1 meter.
urban outfitters corporate headquarters
philadelphia, pennsylvania
Fashion trendsetting Urban Outfitters expected full-range contemporary music throughout its corporate headquarters,
housed in a refurbished industrial structure. Particularly problematic was the cavernous main promenade, where
loudspeakers needed to blend into the chic décor, but had nowhere to hide. The solution was to deploy a system
of custom-painted MM-10XPD directional miniature loudspeakers and MM-10 miniature subwoofers.
“I was shocked by what came out of those
little MM-4XPDs. At first I was skeptical that
they could maintain full articulation up in such
high ceilings. Meyer Sound assured me
they would —and they certainly did.”
Dave Brotman
Owner, DBS Audio Systems
buddha-bar
mexico city, mexico
Music is integral to the ambience at Buddha-Bar Mexico, where DJs mix eclectic music through a discreet
yet potent system of Meyer Sound self-powered loudspeakers. For robust reproduction in the lounge area,
15 UP-4XP loudspeakers are deployed in stereo zones, with bass support from five M1D-Sub subwoofers.
On the terrace, where music must compete with street sounds, 24 MM-4XP miniature self-powered
loudspeakers are augmented by nine MM-10 miniature subwoofers.
“The quality of music reproduction is really
amazing on the system. It adds to the restaurant’s
atmosphere and keeps the customers happy.”
Eduardo López-Guerrero
Operations Manager
Buddha-Bar Mexico
boardroom and conference rooms
houston ballet center for dance
texas
Consistently clear communication is of utmost importance in any conference facility. At the Houston
Ballet Center for Dance, a great many conference sessions also require high quality music reproduction
for use in video presentations. To give the client the best for both voice and music, HFP Acoustical
Consultants specified systems based on Meyer Sound’s self-powered Stella-8C ceiling loudspeakers.
“In a large boardroom, it can be extremely
difficult and frustrating to get a dozen microphones and an automatic matrixing system to
work together precisely as they should. But
with the absolutely uniform response curves of
the Stella-8, from one device to the next, such
problems are much easier to solve.”
Bill Schuermann
Principal Consultant
HFP Acoustical
Hermitage Amsterdam
Amsterdam, Netherlands
The Hermitage Amsterdam museum complex combines aesthetic elegance with modern audio technology
to offer a heightened experience as visitors journey through the remarkable art collection of Russian
heritage. The MM-4XP loudspeakers are mounted to the chandeliers in the church hall and are integrated
into the décor of the upscale Neva Restaurant to provide subtle reinforcement for ambient soundtracks.
“Our requirements called for state-of-the-art audio systems
in the various rooms, from the study centre and the church
hall, to the most challenging of all: the reverberant auditorium. The Meyer Sound system can be easily adapted to
meet our specific needs at any given time.”
Julie Vegter
Head of Programming
Hermitage Amsterdam
18.908.074.01D 1303
Copyright 2013 Meyer Sound Laboratories, Inc.
All rights reserved.
4 Color match of PMS 2718C = c68m38y5k5
Small Use Mark w/ TS Tagline
Mark width standardized at 1.0” but can
vary from 1.0” up to 2.25”. TS Tagline scales
proportionally.
Mark should never fall below 1.0”
thinking sound
what will you design?
Regular Use Mark w/ TS Tagline
Mark width standardized at 2.5”
but can vary from 2.26” up to 4.24”
TS Tagline scales proportionally.
Oversize Use Mark w/ TS Tagline
Mark width standardized at 4.5”
but can vary from 4.25” up to 6.0”
TS Tagline scales proportionally
Mark should never exceed 6.0” in width
2832 San Pablo Avenue
Berkeley, CA 94702 USA
T +1 510.486.1166
www.meyersound.com
sales@meyersound.com