IEC System for Conformity Testing and Certification
of Electrotechnical equipment and Components
Product Identification Document
Report Reference No.
Date of issue
Total number of pages
CB Testing Laboratory
Address
Applicant’s name
Address
Test specification
Standard
Test procedure
CB Scheme FSS
Non-standard test method
N/A
Copyright © 2012 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as
copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from
the reader's interpretation of the reproduced material due to its placement and context.
If this Document is used by non-IECEE members, the IEC/IECEE logo and the reference to the CB
Scheme procedure shall be removed.
Test item description
Trade Mark
Manufacturer
Model/Type reference
Ratings
List of Attachments (including a total number of pages in each attachment):
OD-4002_PID_blank Ed.1.0
2012-11-19
1/9
© IEC – IECEE 2012
IEC System for Conformity Testing and Certification
of Electrotechnical equipment and Components
Copy of marking plate
The artwork below may be only a draft. The use of certification marks on a product must be
authorized by the respective NCBs that own these marks.
PID prepared by
CB Testing Laboratory:
Testing location/ address
Associated CB Test Laboratory
Testing location/ address
Date:
Date:
Tested by (name + signature)
Approved by (name + signature)
OD-4002_PID_blank Ed.1.0
2012-11-19
2/9
© IEC – IECEE 2012
IEC System for Conformity Testing and Certification
of Electrotechnical equipment and Components
TABLE: Components
component
/ materials
function /
purpose
manufacturer / type
OD-4002_PID_blank Ed.1.0
2012-11-19
technical
data
description
3/9
test mark / approval
© IEC – IECEE 2012
IEC System for Conformity Testing and Certification
of Electrotechnical equipment and Components
Figure shows: general overview with enclosure in place
Check: Enclosure
OD-4002_PID_blank Ed.1.0
2012-11-19
4/9
© IEC – IECEE 2012
IEC System for Conformity Testing and Certification
of Electrotechnical equipment and Components
Figure shows: general overview with enclosure in place
Check: Enclosure
OD-4002_PID_blank Ed.1.0
2012-11-19
5/9
© IEC – IECEE 2012
IEC System for Conformity Testing and Certification
of Electrotechnical equipment and Components
Figure shows: bottom view
Check: Enclosure, markings, internal wiring
OD-4002_PID_blank Ed.1.0
2012-11-19
6/9
© IEC – IECEE 2012
IEC System for Conformity Testing and Certification
of Electrotechnical equipment and Components
Figure shows: Inside view: Terminal Block and Appliance Inlet
Check: Components, markings, wires, earthing
OD-4002_PID_blank Ed.1.0
2012-11-19
7/9
© IEC – IECEE 2012
IEC System for Conformity Testing and Certification
of Electrotechnical equipment and Components
Figure shows: Component, sub assembly
Check: Components and materials, dimensions, construction
OD-4002_PID_blank Ed.1.0
2012-11-19
8/9
© IEC – IECEE 2012
IEC System for Conformity Testing and Certification
of Electrotechnical equipment and Components
Additional data
Total weight:
Length of the power cord:
Etc.
Additional information
OD-4002_PID_blank Ed.1.0
2012-11-19
9/9
© IEC – IECEE 2012