PROJECT INFORMATION
MEDMASTER™
Patient Room Luminaires
Job Name
Fixture Type
MPCAE24 SERIES
Catalog Number
Approved by
PRODUCT FEATURES:
»» Ceiling mount – surface, grid or flange; 2'×4'
»» Provides ambient and exam lighting
»» Optional Ingress Barrier Door provides consistent
surface for cleanability
SPECIFICATIONS
HOUSING: FLANGE AND GRID: 20-gauge CRS one-piece construction (IB is one piece seam welded construction). SURFACE: 18-gauge CRS one-piece seam welded construction. Housing Flange:
FLANGE AND GRID: 18-gauge CRS, standard 4-piece construction, spot-welded to housing. Ingress Barrier (IB Option): Mitered and welded corners, spot-welded to housing. Housing Finish: White
TGIC polyester powder coat – 5-stage pre-treatment. Salt spray test: 1,000 hours; Reflectance: 92%.
INSIDE FLANGES: 18-gauge CRS; fastened to housing. Black matte TGIC polyester powder coat – 5-stage pre-treatment. Salt spray test: 1,000 hours.
OPTIONAL DOORFRAME: IB-AC OR IB-HD OPTIONS ONLY. Heavy duty extruded aluminum with clear satin anodized finish. Doorframe supported to housing with aircraft cables (IB-AC) to
provide NSF2 listing, or an optional continuous hinged doorframe (IB-HD). Select in ordering options below. Doorframe secured to housing with continuous hinge (20-gauge SS) and Phillips-head
stainless steel fasteners. Closed cell silicone gasket seals doorframe to housing.
LAMP SHIELDING: Exam compartment shielded by sliding semi-specular aluminum parabolic louver. C
­ lear protective lamp shield securely fastened above louver (see Ordering Information for
alternate Lamp Shield Options). Ambient compartment lamps shielded by perforated steel (white TGIC polyester powder coat finish) with pearlescent acrylic diffuser. Note: Exam compartment clear
protective lamp shield omitted when IB Option is specified.
ELECTRICAL: Fluorescent electronic 120/277V ballasts high power factor (<10% THD). See Ordering Information for optional equipment. Lamps by others. CL Option field adjustable to either side of
bed. One 20W maximum, 12VAC, MR16, 120 or 277 volts. 8° narrow spot recommended. Exam area NEC compliant with isolated wiring compartment for auxiliary branch circuit feed.
INSTALLATION: SURFACE MOUNT: Four .312" diameter holes. GRID MOUNT: Designed for 1" and 1.5" grid. (Housing includes hanging brackets to secure housing with wire to super structure).
FLANGE MOUNT: Yoke mounting hardware & brackets included. Install Frame and Plaster Frames both positively locates yoke brackets within ceiling opening assures alignment of fixture. Install frame
has no need for drywall backing. Backing is supplied on the frame brackets.
LISTINGS: UL and CUL Listed for Damp Location. IB Option UL certified IP65 per IEC 60598.
IP65
OPTION
IB-AC ONLY
ORDERING INFORMATION (Ex: MPCAE24-S-1/3-40B-120-L)
Model
Mounting Options
Lamp Qty
MPCAE24
Lamp Type
Voltage
Lamp Shield Options
Doorframe
Options
Accessories
/
Mounting Options
SSurface
G
Grid (1")
FFlange
Lamp Type
40B F40TT (Biax)
50B F50TT (Biax)
55B F55TT (Biax)
Lamp Quantity (x/x)
Ambient Compartment (x)
1
One Lamp
2
Two Lamps
Exam Compartment (x)
3
Three Lamps
4
Four Lamps
Voltage
120 120 Volts
277 277 Volts
347 347 Volts
Optional Doorframe
IB-AC* Ingress Barrier w/Aircraft Cables
IB-HD* Ingress Barrier w/Continuous Piano Hinge (not NSF2 listed)
Lamp Shield Options (Exam Section)
L
Semi-Specular Aluminum Parabolic 3"×3"
Louver with clear acrylic lamp shield
CMetalized Acrylic Parabolic .62" x.62"
Louver with clear acrylic lamp shield
LW Matte White 3"×3" Louver with clear
acrylic lamp shield
I
.125" #12 Prismatic Acrylic
SL Specified Louver
Options
AMF Antimicrobial Finish on exposed surfaces
CL*
Chart Light – 20W MR16
DLN▲ LED Night Light w/Light Level Control(Lamp by other) (100% - 20%)
EL
One-Lamp Emergency Battery Pack (32°F)
(347V dry location only) – Ambient only
FS
Fuse & Holder
LCL* LED Chart Light
LVC▲ Low Voltage Controller
(See Application Guide or consult factory for switching options)
RF▲
Radio Frequency Filter
TN▲
Night Light – 5/7/9 Watt PL (Lamp supplied by other)
Accessories
C-2063 Lamp, 20W MR16 12VAC 8° Spot
IF Install Frame (Flange only)
*Only available with L or LW Lamp Shield Option
▲
n/a with 347V
www.kenall.com
P: 800-4-Kenall
F: 262-891-9701
10200 55th Street Kenosha, Wisconsin 53144
When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers, and meets the Buy
American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof. May be covered by patents found
at www.kenall.com/patents. Content of specification sheets is subject to change; please consult www.kenall.com for current product details. © 2015 Kenall Mfg. Co. All rights reserved.
MPCAE24-020414
For additional photometry, go to www.kenall.com
MEDMASTER™
Patient Room Luminaires
MPCAE24 SERIES
DIMENSIONAL DATA
CROSS SECTION
B
A
C
CEILING CUTOUT
D
E
DIMENSIONAL DATA (IN INCHES)
A
B
C
DE
MPCAE24
5.80* 23.00×47.00 23.75×47.7523.25** 47.25**
*Add .25" to fixture height when Ingress Barrier (IB) Option is specified
**Add .25" to each cut-out dimension when Install Frame (IF) Accessory is specified
www.kenall.com
P: 800-4-Kenall
F: 262-891-9701
10200 55th Street Kenosha, Wisconsin 53144
When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers, and meets the Buy
American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof. May be covered by patents found
at www.kenall.com/patents. Content of specification sheets is subject to change; please consult www.kenall.com for current product details. © 2015 Kenall Mfg. Co. All rights reserved.
MPCAE24-020414