Installation Instructions
ADVANCED HIGH CEILING
16” Cylinder Series
!
IMPORTANT SAFETY INFORMATION.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Before wiring to power
supply and during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping
must be performed by qualified service personnel. Product must be grounded to avoid potential electric shock
or other potential hazard. Product must be at locations and at heights and in a manner consistent with its
intended use, and in compliance with Electrical Code and local codes.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
7
8”
1. Remove fixture and all components from box.
2. Connect power input wires with corresponding blue/brown/green wires using attached connector at end of wires.
Install cable clamp connector(required, but not included) Push connected wires through cable clamp connector. Clamp to secure.
3. Secure stem (by others) to bracket with two hex nuts (by others) as shown.
METEOR LIGHTING
P: 213.255.2060
F: 213.596.3704
www.meteor-lighting.com
INC01S01-16 V1.1 | Page 1 of 4
*METEOR LIGHTING reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately.
Installation Instructions
ADVANCED HIGH CEILING
16” Cylinder Series
Pendant (Adjustable Aircraft)
Mounting Hole
Junction Box
1
3
Crossbar
Ground Screw
Stud
7
4
Canopy
Terminal
Strain Relief Bushing
2
Coupler
Cable
8
Gripper
6
2 Piece Cable Puck
Half ball end
5
1/16” Cable
9
1. Secure the crossbar to the 4" octagonal box (by others) designed
to support the weight of the fixture.
2. Insert power feed cord through canopy wire hole and secure with
strain relief bushing. Leave sufficient length to make wire
connections.
3. Make ground connection to the ground screw on crossbar.
Connect line voltage to the Black conductor, neutral to the White
conductor.
For 0-10V dimming option, make connections (Data+ to Purple
conductor and Data- to Gray conductor).
4. Thread the cable through the coupler (the terminal side of cable
must be on top). Slide the coupler up to the canopy and secure
with the stud on crossbar.
5. Lay half ball end cables into lower section of cable puck.
6. Attach upper section of puck over top of bottom of puck aligning
power cord holes of upper and lower section of puck. And secure
gripper into top of puck completing puck assembly.
7. Attach puck assembly to fixture by dropping paddle ends of cables
into the 3 holes on the back of the fixture.
8. Insert the cable through the gripper on top of puck. Adjust to
desired height. Thread Cable thru both holes in Cable Locking
Tube and tighten set screws.
9. Insert the cord through the puck. Trim cord to suitable length and
make electric connection in the junction box for fixture.
Paddle
METEOR LIGHTING
P: 213.255.2060
F: 213.596.3704
www.meteor-lighting.com
INC01S01-16 V1.1 | Page 2 of 4
*METEOR LIGHTING reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately.
Installation Instructions
ADVANCED HIGH CEILING
16” Cylinder Series
Wiring diagram
Superior 0-10V
Superior 0-10V Dimming wire
Power wire
BLUE / VIOLET- POSITIVE
Superior
0-10V Dimming
WHITE / GRAY- NEGATIVE
DMX
Power wire
BLUE - NATURAL
BROWN - LINE
GREEN - GROUND
AC WIRE
Standard DMX512 Wire
with 5 pin in/out Connector
(not included)
DMX address
DMX512 is connected using a daisy-chain methodology where the
source connects to the input of the first device, the output of the first
device connects to the input of the next device, and so on.
METEOR LIGHTING
P: 213.255.2060
F: 213.596.3704
www.meteor-lighting.com
INC01S01-16 V1.1 | Page 3 of 4
*METEOR LIGHTING reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately.
Installation Instructions
ADVANCED HIGH CEILING
16” Cylinder Series
DMX Power Supply Box Installation & Electrical Connection
Power Supply:
Before making electrical connections, be sure the AC voltage in your area matches the required voltage for the purchased Meteor LED fixture.
Because the line voltage may vary from venue to venue, you should be sure your unit voltage matches the wall outlet voltage before attempting to
operate the fixture.
DMX-512:
DMX stands for Digital Multiplex Signal. It is a universal protocol used by most lighting and controller manufactures as a form of communication
between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial
data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR connector located on our power supply box.
DMX Linking:
DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller, as long as all
fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable
path possible. DMX512 is connected using a daisy-chain methodology where the source connects to the input of the first device, the output of the first
device connects to the input of the next device, and so on. Network can be expanded across parallel buses using DMX splitters.
Daisy Chain Layout (DMX)
!
Electrical
System
WARNING
1. Before installation, please test LED fixture with DMX
function on ground to ensure compatibility with control
console.
2. DMX address is listed on power box. If DMX address needs
to be reset, please contact our technical department for
further instructions.
3. Our lights require its own channel. If using different fixture
type, please use splitter device to separate.
4. The final fixture should be terminated by the use of DMX
Terminator (by others).
DMX IN
Standard DMX512 Wire Cable with
5 Pin In/Out Connector
DMX IN
DM
X
The dotted lines represent AC power circuits
DMX OUT
DMX OUT
DMX IN
DMX IN
Splitter
DMX Console
METEOR LIGHTING
P: 213.255.2060
F: 213.596.3704
www.meteor-lighting.com
INC01S01-16 V1.1 | Page 4 of 4
*METEOR LIGHTING reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately.