56397450 HOSE / WAND KIT
ConvertaMAX™ 26 Shown
For ConvertaMAX™ 20, 26, 28, 34 / CMAX™ 28ST, 34ST / I-MAX™ 28C, 28HD, 32C, 34HD / BA 750, 750ST, 750C, 850, 850ST
CONTENTS OF KIT
ITEM
PART NO.
QTY
1
2
3
4
5
6
7
8
9
56040772
56002124
56002832
56009042
0116451010
1407629000
56204536
56392171
56397451
56397452
1
12
12
2
2
1
2
6
1
1
DESCRIPTION
Instruction Sheet
Scr, Pan Phil 10-24 x .62
Nut, Hex Nyl Loc-Thin 10-24
Scr, Pan Phil Thd Form 10-24 x .62
Extension Tube
Tool, Plastic Wet
Extension Coupler
Clamp, Plastic
Hose Assembly
Mount
NOTE: Items (1, 2, 7 & 9) are pre-assembled except 2 each of items (1 & 2) and 1 of item (7).
1
2
INSTALLATION INSTRUCTIONS
Pre-drilled Holes
.166 x 2
(4.21mm)
Behind Decal
Mount the Plastic Clamp (7) on the back panel of the machine as shown using the (2) Screws (3). Mount the Plastic Wet
Tool (5) in the clamp as shown. NOTE: The mounting holes in the back panel are pre-drilled, but are under the warning
decal. You can locate them in the approximate area shown by pushing on the decal until you feel the holes and then
puncturing the decal with a center punch or similar tool. If your machine does not have pre-drilled holes, refer to page
two for drilling location dimensions.
Attach the Mount Assembly to the Left side of the machine as shown using the hardware items (1 & 2). Assemble the
remaining components as shown and mount them in the plastic clamps as shown. NOTE: The mounting holes in the
chassis side panel are pre-drilled. NOTE: If your machine does not have pre-drilled holes, refer to page two for drilling
location dimensions.
IMPORTANT!
After installing the Hose/Wand Kit take extra caution while operating machine to ensure that you
Pre-drilled Holes
do not run the machine up against anything and damage the mount and wand assembly on the
.219 x 2
left side of the machine.
(5.56mm)
Refer to the “WET VACUUMING” section of your operator’s manual for instructions on using
these tools.
7
3
6
9
2
5
8
1
Clamp (7) x 5, Screw (1) x 10
& Nut (2) x 10
Pre-assembled to Mount (9)
4
© 2002 Printed in USA, Nilfisk-Advance, Inc.
6
(page 1 of 2)
4/02 revised 5/04 Form No. 56040772
FRONT
ConvertaMAX 20, 26 / BA 550, 650
6" (15.24cm)
Left Side View of Chassis
20" (50.8cm)
Control Handle Back Panel
5" (12.7cm)
.166" (4.21mm)
1" (2.54cm)
3.89" (9.88cm)
6.25"
(15.87cm)
.219" (5.56mm)
FRONT
Left Side View of Chassis
20" (50.8cm)
I-MAX 28HD
ConvertaMAX 28 / CMAX 28ST / I-MAX 28HD / BA 750, 750ST, 850, 850ST
Control Handle Back Panel
4.25" (10.79cm)
4.50"
(11.43cm)
5.50" (13.97cm)
6.50"
(16.51cm)
2.75" (6.98cm)
.219" (5.56mm)
2" (5.08cm)
1" (2.54cm)
ConvertaMAX 28, CMAX 28ST
BA 750, 750ST, 850, 850ST
ConvertaMAX 28, I-MAX 28HD / BA 750, 850
ConvertaMAX 34 / CMAX 34ST / I-MAX 28C, 32C, 34HD / BA 750C
FRONT
4.50" (11.43cm)
4.50"
(11.43cm)
.166" (4.21mm)
I-MAX 34HD
2.20" (5.58cm)
20" (50.8cm)
ConvertaMAX 34, CMAX 34ST
I-MAX 28C, 32C / BA 750C
CMAX 28ST / BA 750ST, 850ST
Control Handle Back Panel
Left Side View of Chassis
20" (50.8cm)
1" (2.54cm)
.166" (4.21mm)
20" (50.8cm)
3" (7.62cm)
6.80"
(17.27cm)
1" (2.54cm)
1" (2.54cm)
3" (7.62cm)
2.40" (6.09cm)
6.50"
(16.51cm)
3.25"
(8.25cm)
4.25" (10.79cm)
ConvertaMAX 34, I-MAX 34HD
(page 2 of 2)
CMAX 34ST / I-MAX 28C, 32C / BA 750C
4/02 Form No. 56040772