July 2016
With BTT6030-2EKA and BTT6020-1EKA for Arduino
1200V galvanically isolated single-channel wide body gate driver IC family
Established AC-
DC Integrated Power Stage Integrated CoolSET™ now available in new package
DSO-12
24V Protected Switch Shield
With BTT6030-2EKA and BTT6020-1EKA for Arduino
The 24V Protected Switch Shield with BTT6030-2EKA and BTT6020-1EKA is a power switch evaluation board compatible with Arduino microcontroller boards and with Infineon’s XMC™ microcontroller kits using the Arduino form factor. The shield is equipped with three PROtected highside power MOSFETs out of the PROFET™+ 24V family (2x
BTT6030-2EKA, 1x BTT6020-1EKA) offering five 24 V channels in total.
Infineon’s PROFET™+ 24V protected high-side switches (BTT6xxx) drive resistive, capacitive as well as inductive loads (e.g. truck bulbs, car bulbs, valves, motors, relays, capacitors, LEDs…). The power switches are controlled via the INx (input) pins. The PROFET™+ 24V devices also provide a sense current at the IS pin, which can be enabled via the DEN (Diagnosis ENable) pin. For the two channel devices the sensed channel is selected via the DSEL (Diagnosis SELect) pin. For each device the sense signal (IS) is connected to an own ADC channel of the microcontroller.
Features
Compatible with Arduino microcontroller boards and
Infineon’s XMC™ microcontroller kits using the Arduino form factor
Capable of PWM up to 400 Hz
Driver circuit with logic level inputs
Diagnosis with current sense
Protection of load and driver circuit e.g. against overtemperature, overcurrent, ESD …
Target applications
Benefits
Fast and inexpensive prototyping of 24 V load driving
Load diagnosis with current sense capability
Overtemperature shut down with latch behavior
Drive resistive, capacitive and inductive loads with PWM or
DC
– 8 ~ 36 V nominal input voltage (max. 5 ~ 48 V)
– Nominal current up to 5 A per channel restricted due to
PCB (BTT6020-1EKA nominal current: 7 A)
– E.g. truck bulbs, valves, motors, relays ...
Product collaterals / online support
Boards and Shields –Hardware Compatible with Arduino
Product page
High Side Switches page
Infineon XMC1100 Boot Kit and PROFET™+ 24V Shield for
Arduino video
Block diagram PROFET™+ 24V
Support/Tools/Software
24V Protected Switch Shield with BTT6030-2EKA and BTT6020-1EKA for
Arduino
Quick Start Guide page
User Manual page
Product Brief page
Software Examples page
PROFET
™+ 24V Product Family
PROFET+ current sense “What designers should know”
Application Brochure: Commercial Construction and Agriculture
Vehicles_2015
Automotive Power Product Selection Guide
PROFET™ Product Selection Guide
PROFET + 24V Shield for Arduino
Applications Example
1
EDI EiceDRIVER™ Compact 300 mil
1200V galvanically isolated single-channel wide body IC family
The 1EDI EiceDRIVER™ Compact 300mil are compact drivers in a wide body package for increased creepage distance, improved thermal behavior, and optimized pin out. These galvanically isolated drivers are based on Infineon’s coreless transformer technology, enabling a world class common mode transient immunity of 100 kV/μs. With current drive strengths of up to 6 A on separate output pins for sourcing and sinking, they are ideal for IGBT based applications such as photovoltaic string inverters, charge stations for electric vehicles, industrial drives, welding equipment, induction heating appliances, and power supplies for servers and telecommunication systems.
Features
Single channel high-voltage gate driver IC
1200 V input-to-output isolation voltage
DSO-8 300 mil wide body package with 8 mm creepage distance
Drives high voltage power MOSFETs and IGBTs
Up to 6 A minimum peak rail-to-rail output
Separate source and sink outputs or active Miller clamp
Benefits
Very low propagation delay of 300 ns or 125 ns (highspeed IGBT versions)
Propagation delay mismatch trimmed down to less than
10 ns
Optimized pin-out for low impedance power supply
100 kV/µs minimum common-mode transient immunity
(CMTI)
No need to adapt signal voltage levels between
μController and driver
Product collaterals / online support
Product landing page,
Product data sheet page
Gate driver selection tools page
Target applications
General purpose inverters
Industrial drives
Photovoltaic inverters
Charge stations for electric vehicles
Welding equipment
Commercial, construction and agricultural vehicles (CAV)
Block diagram
+5V
VCC1
10R
100n
OUT+
3R3
SGND
GND1
OUT-
IN +15V
IN+ VCC2
1µ
INGND2
Circuit diagram using a driver with separate source / sink output
AC-DC Integrated Power Stage -
CoolSET™
Established ACDC Integrated Power Stage Integrated CoolSET™ now available in new package DSO-12
Features
A valanche rugged CoolMOS™ with Startup Cell
Active Burst Mode for lowest Standby Power
Built-in digital soft-start
Auto restart mode for VCC Overvoltage and undervoltage protections
Auto restart mode for overload protection
Auto restart mode for overtemperature protection
Target applications
Adapter/Charger, Blue Ray/DVD player, Set-top Box, Digital Photo Frame
Auxiliary power supply of Server, PC, Printer, TV, Home theater/Audio
System, White Goods, etc
Product collaterals / online support
Product landing page
Demo boards page
Block diagram
Benefits
Digital frequency reduction for better overall system efficiency
Pb-free lead plating, halogen free mold compound,
RoHS compliant
Product Data Sheet Page
ICE2QR1080G
ICE2QR4780G
ICE3AR1080JG
ICE3AR2280JG
ICE3RBR0665JG
ICE3AR4780JG
ICE3RBR1765JG
ICE3RBR4765JG
Evaluation Boards
DEMO-2QR1080G
DEMO-2QR4780G
DEMO-3AR1080JG
DEMO-3AR2280JG
DEMO-3RBR0665JG
DEMO-3AR4780JG
DEMO-3RBR1765JG
DEMO-3RBR4765JG