For Product
Info
SmartLink Output Module
VOM-LN04-01
Quick Reference Guide
The SmartLink four port (VOM-LN04) output module is inserted
into the Savant SmartMediaPro family of modular matrix switchers.
The VOM-LN04 module uses HDBaseT technology to extend audio
and video signals over a common Cat 5e/6/7 cable up to 328 feet
(100 meters). Each output connection on the front of the module
(Link 1-4), is cabled to a device that supports receiving HDBaseT
audio and video.
Front Panel VOM-LN04
IMPORTANT !! Savant recommends using a Cat 5e/6/7 shielded
cable as well as metal RJ-45 connectors with a drain wire soldered
to the connector. Shielded cable and connectors are recommended
to safeguard against any unpredictable environmental electrical
noise which may have an impact on performance.
Box Contents
Module Removal
Tool Slot
Insert the module removal tool into this slot
and pull outwards to remove the module from
the chassis.
Link 1, 2, 3, 4
RJ-45 output ports support HDBaseT audio
and video. Each Link x output is cabled to an
HDBaseT device using a Cat 5e/6/7 cable.
VOM-LN04
(1) VOM-LN04-01 Output Module
(1) Quick Reference Guide (This document)
Note: The Link x output ports are not fully
five play compatible. Each port supports
HDBaseT audio and video only.
Specifications
Retaining screws
Environmental
Temperature
32° to 104° F (0° to 40° C)
Humidity
10% to 90% Relative Humidity (noncondensing)
M3 x 6 mm Phillips head flush mount retaining
screws fasten the VOM-LN04 assembly to the
SmartMediaPro chassis.
• Screws are pre-installed into
SmartMediaPro chassis securing preinstalled blank panels.
Dimensions and Weight
Height
1.31 in (3.33 cm) - Faceplate
Width
5.11 in (12.98 cm) - Faceplate
Depth
6.98 in (17.73 cm) - Faceplate and Board
Weight (Shipping)
1.0 lb (0.45 kg)
Module Installation and Removal
Follow the installation and removal instructions below to remove
and/or install the VOM-LN04 module into a SmartMediaPro chassis.
Tools Required
The following items are not supplied with the module but are
needed during the installation and/or removal process.
Power
Power is supplied through the SmartMediaPro chassis when module
is inserted into chassis (Do not hot plug module).
•
•
Compliance
Safety and Emissions
FCC Part 15 | CE Mark | C-Tick
RoHs
Compliant
Module Installation Precautions!!
Observe the following precautions to avoid damage from
electrostatic discharge (ESD) when handling modules.
Minimum Supported Release
Savant OS
#2 Phillips screwdriver
Module Removal Tool (Included with the SmartMediaPro chassis
- 071-0268-xx)
•
da Vinci 5.2.1
•
•
Use an approved ESD wrist or ankle-grounding strap. Ensure the
grounding strap makes good skin contact.
Connect the clip end of the ground strap to a threaded
grounding stud on the chassis.
When returning a replaced module to Savant, place the module
in either the clamshell packaging it was originally shipped in or in
a static shielding ESD safe bag.
NOTE:
The wrist strap only protects the component from ESD voltages on
the body; ESD voltages on clothing can still cause damage.
VOM-LN04 Output Module | 009-0907-03 | 150220
Copyright © 2015 Savant Systems, LLC
1
of 2
45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
Module Installation
Module Removal
Refer to Module Installation Precautions above before installing
module.
Refer to Module Installation Precautions above before removing
module.
1. Power Off the SmartMediaPro Chassis using the power switch
located on the rear of the chassis and disconnect the AC power
cord.
1. Power Off the SmartMediaPro Chassis using the power switch
located on the rear of the chassis and disconnect the AC power
cord.
2. Remove the blank panel from the rear of the SmartMediaPro
chassis by removing the (2) M3 X 6 mm Phillips retaining
screws. Set screws aside as they will be used later in procedure.
Note: Label and remove any cables currently connected.
2. Remove the (2) M3 x 6 mm Phillips retaining screws. Set screws
aside as they will be used later in procedure.
3. Align the module board with the two rails located at the bottom
of the opening created when removing the blank plate.
3. With the notch in the module removal tool (included with
SmartMediaPro chassis) facing downward, insert the tool into
the slot in the module faceplate
4. Slide the module all the way until a slight resistance is felt. This
is where the connector on rear of board gets seated into the
connector in chassis.
4. Lower the tip of the tool downward to ensure it is hooked
behind the faceplate and with slight outward pressure, pull the
module outward. A slight resistance will be felt as the module is
unseated from the chassis side of the connector.
5. Gently press on the module the rest of the way until it seats into
the connector at the rear of the slot and the plate seats against
the chassis.
6. Finish the installation by fastening the module to the chassis
using the (2) M3 x 6 mm retaining screws removed earlier.
5. Slide module out until it is completely removed from chassis.
6. If the module is being replaced, refer to the Module Installation
instructions for proper installation procedures.
7. If the module is not being replaced, install a blank plate using
the (2) M3 x 6 mm retaining screws removed earlier. This will
ensure that proper airflow through the chassis is retained as
well as preventing dust and debris from entering the chassis.
Wiring and Connections
After unpacking and installing the VOM-LN04 module, cable the module as displayed below.
Additional Information:
• Link x outputs are cabled to any HDBaseT extender device such as the Savant IRX-LN01 or HRX-SLN501.
• Not 5Play™ compatible. Supports HDBaseT audio and video only.
• Do not connect Link x outputs to an Ethernet switch or router.
Additional Information
•
For additional Information, refer to the 009-0418-xx SmartMediaPro Deployment Guide (SSP-0600, 1200/1200R).
VOM-LN04 Output Module | 009-0907-03 | 150220
Copyright © 2015 Savant Systems, LLC
2 of 2
45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500