Aliante
4’/5' Pendant - Cable Version
Installation
Customer service: 610.282.7472 or fixtures@lutron.com
®
LED / Fluorescent
041126d 07/2014
Hardware Included:
10-32 x 1 in
(25 mm)
Screw(s)
Level
Phillips head screwdriver
Flat head screwdriver
Wire strippers
Scissors
Adjustable wrench
Ruler/straight edge
Wire Nut(s)
Grilles (optional)
NOTICE: Fixture parts are scratchable.
Keep lamp base in box to protect finish and for assembly.
Lamp Base
Remove protective film on canopy and base after installation.
Use with 4” (10 cm) or smaller round or octagonal recessed junction
box, Cut hole in drywall or ceiling panel close to junction box. Fixture
brace and support from structure required for suspended ceiling.
Mounting Ring
Mounting Ring Plug
*Higher than 12’ (366 cm)
consult designer.
Chassis
Do not remove chain from ring or chasis.
Canopy
Ceiling Height
T5HO, 54/80 W, 4’/5’ (122/157 cm) fluorescent lamp not included.
LED light source included with LED fixture.
7’9” – 12’
236 cm-366 cm
Recommended
Fixture Height
6’9” – 7’2”
206 cm-218 cm
NOTICE: This product is to be installed by a licensed electrician. To avoid the risk of damage
to product do not install over cooktop or other hot surfaces. Do not hang from fixture.
1
Aliante
4’/5' Pendant - Cable Version
Installation
Customer service: 610.282.7472 or fixtures@lutron.com
®
LED / Fluorescent
2-2
1 ASSEMBLY
2
1
1-1
Make sure screws are tight atmepndbsaosef .la
Turn
OFF circuit
breaker
pretados
Asegúrese
de que
los tornillos
estén aen los
and
switch/dimmer.
extremos
de la base de la luminaria.
extrémités
aux
On (6
mm)
x. Tornillos
1/4”
.
041126d 07/2014
1A
To orient correctly, use
holes 1 and 1A
or 2 and 2A.
2A
Off
2 ATTACHMENT TO CEILING
2-1
1/4”
6 mm
Mounting Ring
2-3
Attach base unit by inserting cables through grippers in canopy chassis. Press in
gripper plunger to allow cable to pass through the gripper. When grippers
are released the cable is locked into place. Adjust each cable so bottom of
fixture is at least 6’ 6” (198 cm) above the floor.
Plunger
Gripper
2
Aliante
4’/5' Pendant - Cable Version
Installation
Customer service: 610.282.7472 or fixtures@lutron.com
®
LED / Fluorescent
2-4
041126d 07/2014
CONTINUED
After fixture is positioned, measure 12” (30 cm) of cable above each gripper and cut off the excess. Push back the metal jacket to expose insulated
wire and strip back 3/8” (9 mm) of the insulation.
1/2 in
13 mm
3/4 in
19 mm
12”
30 cm
Insulated
Wire
2”
5 cm
5-6”
13-15 cm
3/8”
9 mm
2-5
Metal Jacket
3 WIRING
3-1
TROUBLESHOOTING TIPS
If stiff 1/4” (6 mm) long piece at the end of the cables has been cut
off before cables are inserted into grippers of canopy chassis: Push
metal jacket back on the cable and cut off 1/2” (13 mm) of the wire
underneath. Pull jacket back over wire. Twist jacket in area without
insulated wire inside to trap the wire and form a stiff piece for
insertion into the gripper. Return to step 2-4.
Chassis
3
Aliante
4’/5' Pendant - Cable Version
Installation
Customer service: 610.282.7472 or fixtures@lutron.com
®
LED / Fluorescent
3-2
Non-dim / 2-Wire Dimming
3-Wire Dimming
Black
(Hot / Line)
Green
(Ground)
041126d 07/2014
White
(Neutral)
Yellow,
Orange or
Red
Yellow
Note: Two hot power leads are needed for dimming operation. If
there is a dimmable fixture but only 3 wires available from the
power side (only one hot), connect the black and the yellow lead
from the fixture to the hot wire (black) from the junction box.
White
(Neutral)
Black
(Hot / Line)
Green
(Ground)
4 FINAL MOUNTING AND ADJUSTMENT
4-1
Note: For units requiring C5-BMF-2A, refer to the C5-BMF-2A
installation guide for correct wiring.
10-32 x 1”
(25 mm)
Screw(s)
4-2
Install
canopy
cover.
4
Aliante
4’/5' Pendant - Cable Version
Installation
Customer service: 610.282.7472 or fixtures@lutron.com
®
LED / Fluorescent
4-3
041126d 07/2014
4-5
Fluorescent Only
Optional grille
installation
4-6
4-4
Turn ON circuit breaker
and switch/dimmer
Leveling adjustment: Level lamp base by pressing in gripper plunger
in fixture base to allow cable to pass through the gripper. Release
gripper plunger to lock cable in place. Use Positions A, B, and C to
put leveling device. Note: Fixture base grippers are for fine
adjustments of up to 1 in (25 mm) per cable. Use canopy grippers
for course adjustments.
On
Off
TO CHANGE BALLAST/DRIVER
Note: FCC approval is voided if the ballast/driver is changed.
Plunger
Remove protective film
after installation.
A
B
C
Ballasts/drivers should be professionally replaced. To change ballast/
driver, support base of lamp and remove 4 screws in corners.
Gripper
5
Aliante
4’/5' Pendant - Cable Version
Installation
Customer service: 610.282.7472 or fixtures@lutron.com
®
LED / Fluorescent
Lamp case will swing out. Remove from hinge and lower (support
with your hand). Ballast/driver can be accessed from the side.
041126d 07/2014
Technical Notes
Standard cables are made for ceilings up to 12’ (366 cm). For longer cables,
contact the manufacturer.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE
APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH
THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
Limited Warranty
For full 5-year warranty details, see
www.lutron.com/TechnicalDocumentLibrary/3672203.pdf
Trademarks
IVALO, IVALO Lighting, and Aliante are registered trademarks of IVALO Lighting, Inc.
Lutron and ) are registered trademarks of Lutron Electronics Co., Inc.
For Help
For help with applications or installations, please contact us at 610.282.7472
Ballast/driver
Ivalo Lighting Inc.
7136 Suter Road
Coopersburg, PA 18036-1299, USA
Customer Service: 610.282.7472
Fax: 610.282.7600
www.lutron.com/ivalo
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, USA
World Headquarters 610.282.3800
©2014 Lutron Electronics Co., Inc.
6