EAPL Model A1D1 On Power application preset timing starts and at

advertisement
EAPL
Model A1D1
FRONT VIEW
INSTRUCTION MANUAL
FUNCTION
A1D1 (CSA) is an ON Delay Timer.
On Power application preset timing starts
and at the end of the timing 2C/O relay
contacts changes over and remain in this
state till the power is interrupted.
A1D1 (CSA) ON DELAY TIMER
www.eaplindia.com
DIMENSIONS
NOTE: ALL DIMENSION ARE IN MM
Terminal Details
A1, A2
: Source Voltage
15, 16, 18 : C1, NC1, NO1
25, 26, 28 : C2, NC2, NO2
Contact Rating
5Amps @ 250V AC/ 28V DC Resistive Load
CONNECTIONS
SIDE VIEW
1.
2.
3.
4.
5.
Terminal block
Slide switches for range selection
Relay status LED
Time Tuning Pot
Range viewing window
DOC NO: OD RA AN 09000 0 REV NO.: 00 Dtd: 26/06/2013
Page 1 of 2
Special instruction for CE marked product :
1) Ensure specified operating voltage is applied to the product as per
Product Specification.
2) Ensure connected LOAD does not exceed the specified contact rating of
the product. (Refer Product Specification).
3) Use 2.5mm2 wire with Fork type Terminal Ends (Insulated with metal
re-inforcement) to connect Load terminals (15-16,18 & 25-26,28) and
source terminals (A1 & A2).
4) Wrong use and application of wires not only shorten their lives but may
also cause a serious accident.
5) To prevent Fire and Electric Shock use UL and/or CSA approved wires.
6) After connecting the Source and Load connections place protective
cover on terminal block and ensure perfect locking such that, protective
cover shall not fall due to vibrations.
PROGRAMMING INSTRUCTION :
Select the range with the help of 2
Once the product life is
slide switches on the side panel. The
over, you may send
selected range can be seen in the
back the unit to EAPL
windows on the front panel.
for disposition.
Set the required time by gently
rotating the Front pot with suitable
screw driver.
Apply rated voltage across source TROUBLE ANALYSIS
terminals.
The time starts immediately and RED
Unit not working.
LED glows and Relay changes over.
Check power supply
(Rated supply should be
After the set time the LED stops
glowing and relay contact changes
applied).
from NC to NO.
Relay remains in same state, till
CONTACT
power is interrupted.
7) Ensure Live Parts are not accessible after placing the protective cover.
8) Mount the product on DINRAIL and ensure the Spacing of 10mm
minimum between product to product.
9) During time setting and range selection ensure power is removed for
both source and load terminals.
10) Do not open the product at any instance since no user serviceable
parts inside.
HINTS ON CORRECT USAGE
Use proper gauge wires for connections.
Ensure all terminals are tightly screwed.
Source Voltage should not exceed specified limits.
DISPOSITION
CAUTION
Electronic Automation Pvt. Ltd
#20, KHB Industrial area
Newtown Yelahanka
Bangalore -106
Do not change the time range &
set time while the timer is in Ph:+91-80-28567561/2
operation.
,/42802345
Switch off the power while
changing the time range and set Email : info@eaplindiamail.com
time.
www.eaplindia.com
Application of voltage other than
the specified one will permanently
damage the timer.
Do not forcibly rotate the pot. It
will damage the timer.
DOC NO: OD RA AN 09000 0 Dtd : 26/06/2013
Page 2 of 2
SIGN & DATE PREPARED: K.Priyadarshini
25/06/2013
CHECKED: B.S.Sridevi
26/06/2013
APPROVED: Kalavathi Shanbhag
26/06/2013
DOC NO: OD RA AN 09000 0 Dtd : 26/06/2013
Download