Product Introduction
No.M30053
2010.02　Rev.1
TEST BD-R
For Checking BD Optical Pickup
ABD-R100P
1. Purpose of use, Features
ABD-R100P is 25GB BD-R Test Disc on which data are recorded in the form of band. It is designed for
adjustment, inspection and phase confirmation of Optical Pickups. Since Jitter value is strictly controlled
by optimizing recording strategy, quality of each parameter of the disc is always stable and close to equal
with previous lot when the lot of the disc change.
Moreover since skew is also strictly controlled, stable alignment and evaluation of pickup are available
without regard to disc quality and variation.
2. Specifications
（1） Disc type
・ BD-R Disc Single Sided Dual Layer
・ Physical Characteristics ： Complies with BD-R Part 1 Basic Format Specifications Ver. 1.3
（2） Performance of Jitter and Skew
Parameters
Jitter LB
Jitter
Jitter ( LL/ LT )
Radial direction
Skew
Tangential direction
Our management value
＜5 %
＜5.3 %
≦± 0.3°
≦± 0.2°
BD-R Spec. value
≦7%
≦± 0.6°
≦± 0.3°
（3） Recording specification
Recorded area
R39.0 ～ R41.0　mm
Physical ADIP Address
9E65Ah ～ B3CC4h ※1
Recorded data
Fixed Data ：　Repeated 42h,44h
Recording strategy
Optimized by ALMEDIO
DMS
None DMS (Disc Management Structure) ※2
※1 Recorded PSN of Fixed Data at Physical ADIP Address is all the same address of 740000h.
※2 ABD-R100P is recognized as Blank Disc by Normal Mode of BD Players and BD Recorders etc.
since it is recorded by special mode without DMS.
note) Be careful not to record additionally on ABD-R100P.
1/2
Product Introduction
No.M30053
2010.02　Rev.1
3. Comparison of measurement data among ABD-R100P, ABD-R520W and ABD-520
・ Following table and graphs are comparison measurement data of RPP and Jitter values among
ABD-520 (BD-ROM press item), ABD-R520W (BD-R item) and ABD-R100P.
・ Jitter of ABD-R100P shows good value compared to ABD-520 and ABD-R520W.
Jitter with Limit Eq.
Disc Type
Recorded
No.
RPP ave.
LB
LL
1
0.143
5.20
4.94
BD-ROM
ABD-520
2
0.141
5.20
5.04
1
0.271
5.62
5.89
ABD-R520W
2
0.274
5.81
6.08
BD-R
1
0.252
4.69
4.36
ABD-R100P
2
0.253
4.70
4.31
RPP ave.
LT
5.46
5.36
5.33
5.52
5.01
5.06
Jitter
BD-R Spec.: ≦7.0%
≦
BD-ROM Spec.: 0.10 to 0.35
BD-ROM Spec.: ≦6.5%
BD-R Spec.: 0.21 to 0.45
Measurement point: R40mm
4. Use other than pickup, custom ordered item
・ ABD-R100P is mainly designed for evaluation of Optical pickup, other than that it is available to use
for BD Players and BD Recorders etc. if special mode (manufacturing process mode, inspection mode
etc.) is selectable.
・ When ABD-R100P is used for adjustment, further request for example cutting to 8cm size,
eccentricity processing for phase adjustment etc. are available as a special order product.
Please make a contact to our sales staff should you have further question.
Values in this sheet are measured by the equipments ALMEDIO-owned. Appearance and specifications are subject to change without notice.
<Proper handling of the disc>
Do not write on the surface with a pen and others, nor put a
sticker on it.
Do not expose the disc to direct sunlight, nor leave it in the
place of high temperature and high humidity.
After playing, store the disc in its own case.
2/2
ALMEDIO INC.
Sales Headquarters
Sakae, 2-32-13, Higashimurayama, Tokyo, Japan
TEL：+81-(0)42-397-1331　FAX：+81-(0)42-397-1919
http://www.almedio.co.jp/english/index.phtml
E-Mail : tm-sales@almedio.co.jp