COMMISSIONING
FOR COMPREHENSIVE INSTRUCTIONS REFER TO THE POLOPHONE
INSTALLATION MANUAL REFERENCE: 1163.D.01.0001_2
1
2
B
A
Entry Panel Selector Switch and Volume Control
CENTURION SYSTEMS (PTY) LTD
CENTURION
THE AUTOMATIC CHOICE
WEB: http://www.centsys.co.za
Sharecall Number: 0860 103 726
General information e-mail: info@centsys.co.za
POL phone
to have and to hold
POL POL
Entry Panel Selector Switch and Volume Control
! If the system has only one entry panel set the selector switch (A) to the
upper position or (1).
! If there are two entry panels set the selector switch on the one panel to the
upper position (1) and on the other panel to the lower position (2).
! When adjusting the speech volume start by setting the control knob (B)
approximately 75% of full volume. Clockwise rotation increases the
volume. Having set the volume adjustment on all the handsets to the
same volume then optimise the speech volume at the entry panel(s).
Latest Revision: 24.11.2006
COMMISSIONING
Entry Panel Selector Switch and Volume Control
! If the system has only one entry panel set the selector switch (A) to the
upper position or (1).
! If there are two entry panels set the selector switch on the one panel to the
upper position (1) and on the other panel to the lower position (2).
! When adjusting the speech volume start by setting the control knob (B)
approximately 75% of full volume. Clockwise rotation increases the
volume. Having set the volume adjustment on all the handsets to the
same volume then optimise the speech volume at the entry panel(s).
FOR COMPREHENSIVE INSTRUCTIONS REFER TO THE POLOPHONE
INSTALLATION MANUAL REFERENCE: 1163.D.01.0001_2
1
2
B
A
Entry Panel Selector Switch and Volume Control
CENTURION SYSTEMS (PTY) LTD
WEB: http://www.centsys.co.za
CENTURION
THE AUTOMATIC CHOICE
Document Ref: 1163.D.01.0002_5
POL phone
to have and to hold
Sharecall Number: 0860 103 726
General information e-mail: info@centsys.co.za
Latest Revision: 24.11.2006
Document Ref: 1163.D.01.0002_5
WIRING DIAGRAM
ENTRY PANEL
HANDSET
1
2
1
2
-+
1
2
NO
COM
1
2
-+
-+
NO
COM
NO
COM
1
2
1
2
_
+
B
NO
COM
A
1
2
_
+
-+
See Note
Below
1
2
_
+
See Note
Below
_
+
NO
NO
NO
NO
COM
COM
COM
COM
POWER SUPPLY
FOR DOOR STRIKE
EXTRA
HANDSETS
AUXILIARY OUTPUT/POTENTIAL FREE NORMALLY OPEN
- GATE PEDESTRIAN OPENING
- PILLAR LIGHT CONTROL
- ENTRANCE LIGHT CONTROL
BATTERY SUPPLY
NOTES:
Power Supply
DOOR
STRIKE
TRG COM
POTENTIAL FREE
NORMALLY OPEN
CONTACT TO
ACTIVATE GATE
MOTOR ETC.
1. Only one 12V DC Power Supply is typically needed to power the system.
2. Power can be connected to any component in the system.
3. The diagram shows the 12V Battery Supply of gate motor connected to the
entry panel to power the system.
4. If power is being connected to the handset use either a mains adapter with
a DC jack compatible with the socket provided (A) or connect 12-14V DC
to the terminals (B).
B.
WARNING
If the gate trigger wire is connected to a potential free contact (NO or COM) on the entry panel, the gate can be opened by joining
the NO and COM terminals together.
For additional security it is advisable to wire to the auxiliary terminals on the handset or connect the PoloSwitch in the gate motor.
WIRING DIAGRAM
ENTRY PANEL
HANDSET
1
2
1
2
-+
1
2
NO
COM
1
2
-+
-+
NO
COM
NO
COM
1
2
1
2
_
+
1
2
_
+
-+
B
_
+
See Note
Below
NO
COM
A
See Note
Below
1
2
_
+
NO
NO
NO
NO
COM
COM
COM
COM
POWER SUPPLY
FOR DOOR STRIKE
EXTRA
HANDSETS
AUXILIARY OUTPUT/POTENTIAL FREE NORMALLY OPEN
- GATE PEDESTRIAN OPENING
- PILLAR LIGHT CONTROL
- ENTRANCE LIGHT CONTROL
BATTERY SUPPLY
NOTES:
Power Supply
TRG COM
POTENTIAL FREE
NORMALLY OPEN
CONTACT TO
ACTIVATE GATE
MOTOR ETC.
DOOR
STRIKE
1. Only one 12V DC Power Supply is typically needed to power the system.
2. Power can be connected to any component in the system.
3. The diagram shows the 12V Battery Supply of gate motor connected to the
entry panel to power the system.
4. If power is being connected to the handset use either a mains adapter with
a DC jack compatible with the socket provided (A) or connect 12-14V DC
to the terminals (B).
B.
WARNING
If the gate trigger wire is connected to a potential free contact (NO or COM) on the entry panel, the gate can be opened by joining
the NO and COM terminals together.
For additional security it is advisable to wire to the auxiliary terminals on the handset or connect the PoloSwitch in the gate motor.