March 2015
Product Description
3M™ Slip Resistant Removable Coating is an indoor, durable, film layer. When cured, the film acts as a protective, slip resistant layer that can
then be easily peeled away without residue.
Suitable Areas
Recommended:
Indoor use only
Bathrooms
Kitchens
Entrance Ways
Laundries
Low water pooling areas
Other slip hazard areas
Not Recommended:
x Inside Showers/Bathtubs
x On soft, highly porous, uneven or textures surfaces: unsealed
natural stones, timber floors, unpolished concrete floors
Recommended Floor Types
Not Recommended Floor Types
Ceramic/
Porcelain Tiles
(Glazed, nonporous)
× Travertine
(a.k.a. travertine
limestone or
travertine marble)
Vinyl
Tiles/Sheets
(Smooth finish)
× Slate
Marble
Vein
appearance
× Terrazzo
Granite
Flaky
appearance
× Timber floors
Polish
concrete has
high gloss
surface
× Unpolished
Concrete
Polish
Concrete
Layered look with
small pores. Pores
can be minimised by
filling and polished.
Rough uneven
surface, grey earth
tones
Stones in cement and
polished
Grouts are generally porous and the 3M TM Slip Resistant Removable Coating will be of high adhesion.
Product is suitable for floors with narrow grout widths and/ or shallow grouts.
x Product is not suitable for deep and/or large grout widths, or floor surfaces that have a large proportion of grout compared to tiles, such as
mosaics and small tiled floors.
x Floors with fragile grouts or fragile tiles are not suitable.
This product may leave a cleaner appearance to the coated area after removal.
Page 1
3M™ Slip Resistant Removable Coating Instruction Sheet. 3M is a trademark of 3M Company. © 3M 2015
Surface Preparation
1.
2.
3.
4.
Clean floor to remove any soil, oily stains and soap scum.
Allow sufficient time for the area to fully dry.
Test a 3cm diameter patch using a teaspoon of product in an inconspicuous area. Refer to Spot Check below.
Allow to dry and peel coating. Recommended to apply overnight to allow sufficient drying time.
Spot Check
1
2
Perform test patch a day prior to
application by applying spoonful of
coating in and around grout area.
Peel film when fully dried and
check for any signs of grout and
surface damage.
How to Use
DIRECTIONS OF USE:
STEP 1: Identify and Clean the area you want to make Slip
Resistant. Mask the area to prevent overspill e.g. edges, drains.
STEP 2: Invert bottle several times before use. Do not shake
vigorously. Follow coating guide. Pour and spread evenly with a
short nap mohair roller. Fill grout lines generously.
STEP 3: Apply two or more coats and leave to dry. Allow
approximately 2 hour drying time between coats. Ensure each
coat is dry before applying the next.
*First Coat Volume includes 100ml for roller absorption ( 230mm
roller). Add 10-15% extra for first coat if there are wide or deep grout
lines in the floor.
Masking (Optional)
1
2
Mask boundary of area to prevent overspill with painter’s masking tape e.g. edges, drains. 3MTM 38mm ScotchBlue™ Edge-Lock™
Painters Tape is recommended. Apply firm pressure along the tape and into the grout area to ensure sufficient adhesion.
Coating
1
2
Evenly coat the area by rolling lightly with a short nap mohair roller. Roll both
directions for even distribution. Complete coating within 15 minute window.
Page 2
3
Allow coating to dry for at least 2 hours before
recoating. Drying time may vary depending on the
ambient temperature and humidity. A minimum of
2 coats is required and 3 coats is recommended.
3M™ Slip Resistant Removable Coating Instruction Sheet. 3M is a trademark of 3M Company. © 3M 2015
Masking Removal when Dried
1
2
Ensure film is touch dry when
removing masking tape. Use a
stainless steel blade cutter to cut
along the tape. NOTE: Perform a
scratch test to ensure cutter does not
scratch floor surface.
Carefully remove masking tape.
Peel tape slowly.
3
Film is ready for use. Allow 8 hours (or
overnight) curing time to achieve water
resistance.
Maintenance
Sweep coating with clean dust pan and brush.
Mop area with warm soapy water if required.
DO NOT use strong cleaning agents, such as bleach.
For tough stains, consider using a bristle scrubber.
Any damages on surfaces can be repaired by applying a top coat or cut out the area with a sharp blade and re-apply.
Film Removal & Disposal
1
Lift edge of film from corner using a
scraper. Start peeling back SLOWLY
at 90 degrees to the surface. If the
film breaks, repeat the process.
2
Sweep the area to clean off any
debris. Cut the film into manageable
pieces before disposal in general
waste.
Safety Information
KEEP OUT OF REACH OF CHILDREN.
• Read product label before use.
• Protective eyewear and gloves are recommended during application.
• Use in a well ventilated area.
• Do not eat, drink or smoke when applying this product.
• Wash hands and other exposed areas thoroughly with soap and water following application of product.
3M Australia Pty Limited.
Bldg A, 1 Rivett Rd, North Ryde,
NSW, 2113.
Product Info: 136 136
Emergency: 131 126
Page 3
3M New Zealand Limited.
94 Apollo Drive, Rosedale,
Auckland, 0632
Ph: 09-477-4040,
Emergency: National Poisons Centre 0800 764 766.
3M™ Slip Resistant Removable Coating Instruction Sheet. 3M is a trademark of 3M Company. © 3M 2015