LED Indications - Display Driver
Startup
Bootloader
Profile Assigned
Profile Assigned
Solid
Error
square and dotted magnetic
sensor activated together
Factory
default
Self test fail
10
5
Factory Default
1
Pending Magnetic Sensor
activations
1
In the mesh
Controlled by Panel/Gateway
Fire protection provided
Note: The following patterns are supported. Actual usage
will be set by the FACP based on system events.
Typical usage
Profile
removed
Normal Mode
Timeout
with SWIFT
Tools
Timeout
18
18
18
Solid
Rescue Mode
10
10
90
Profile
received
Waiting for
profile
square
magnetic
sensor
activated
1M
3
8
Searching for
mesh (in
rescue mode)
with or
without
SWIFT
Tools
Timeout
0.5
Slot request
rejected,
searching for
mesh (in
formation
mode)
Slot not
assigned
Solid
Searching
for profile
Slot not
assigned
6
12
12
12
25
Searching for
mesh (in
formation mode)
Slot
assigned
Alarm/Active State
3
3
3
Trouble
Timeout
Solid
Slot
assigned
6
Discovered
Mesh
20 M
5M
6
Mesh
forming
Discovered
Mesh
6
1st Mesh
restructuring
Mesh forming:
Device is in the mesh and searching for other devices.
Any device in the mesh can transition to mesh forming mode.
Bootloader
Legend
Example:
1st blink is green. 2nd is yellow
LED color
Two blinks in this pattern
No. of blinks
20 M
Interval between blink patterns
Bootloader
Normal
Bootloader
Firmware
Update
7
Duration of LED state
7 sec between blink patterns
Will transition to next state after
20 minutes (approx.)
Approximate duration
All units are in seconds. Minute is indicated by M.
PN 50122634-001:C 7/30/2015 15-351
2
Fold on dotted line.
Fold on dotted line.
Fold on dotted line.
LED Table - Display Driver
In The Mesh
LED Pattern
Solid
Self test fail
Condition
Action Required
Device has failed internal self
diagnostics
Restart the device. If problem persists.
Contact customer support
LED Pattern
Condition
Active/Alarm state
Device has been activated
Active/Alarm state
Device has been activated
Active/Alarm state
Device has been activated
Rescue mode
Device is in the mesh and
searching for lost devices
Device may be in trouble
Rescue mode
Device is in the mesh and
searching for lost devices
Rescue mode
Device is in the mesh and
searching for lost devices
Normal mode
Device is in the mesh
and may be in trouble
Normal mode
Device is in the mesh
Normal mode
Device is in the mesh
Mesh forming
Device is in the mesh and looking
for devices that are not in the mesh
Action Required
3
5
1
Solid
Profile
removed
Profile
received
Device has returned to factory
default state
3
Device is now profile assigned.
3
10
Factory Default
LED Pattern
10
1M
0.5
Waiting for
profile
Condition
3M
12
3M
12
Action Required
Device is factory default
3M
Searching
for profile
Refer to the panel to identify
the trouble and possible solution
Device is factory default and
requesting a profile from a
distributor or gateway
12
Use SWIFT Tools to assign profile or
activate switch to search for profile
18
18
Refer to the panel to identify
the trouble and possible solution
Profile Assigned
LED Pattern
8
90
3
Condition
Action Required
Slot
request
rejected
Device not permitted into the
mesh
Confirm device count and software
version
Searching for
mesh (in
rescue mode)
Profile is assigned
18
20 M
6
5M
6
1st Mesh restructuring
Legend
Mesh is formed and initializing
No. of blinks
LED color
Interval between blink patterns
Duration of LED state
Bootloader
25
Searching for
mesh (in
formation
mode)
Profile is assigned and device
is searching for the mesh
Ensure the mesh is in rescue mode
or wait for timeout to search mesh
in formation mode
LED Pattern
Approximate duration
Condition
Action Required
Device is ready to update
Use SWIFT Tools to initiate
the download
Example:
Bootloader
Normal
Two blinks in this pattern
1st blink is green. 2nd is yellow
10
1
Pending
Magnetic
Sensor
activations
20 M
Ensure the mesh is in formation mode
Bootloader
Firmware
Update
New application code is being downloaded
7
7 sec between blink patterns
Will transition to next state after
20 minutes (approx.)
All units are in seconds. Minute is indicated by M.