LED Indications - Gateway square magnetic sensor activated Solid 1 Factory default Profile accepted Create profile dotted magnetic sensor activated 10 10 Solid 1 1 Pending Magnetic Sensor activates 10 Profile accepted Create profile Startup Profile Assigned No magnetic sensors activated within the 10 seconds square & dotted magnetic sensor activated together 10 10 1 Profile removed Pending Magnetic Sensor activations 1min timeout Bootloader 5 1 Factory Default 60 Activate either magnetic sensor Waiting for Profile 0.5 Searching for Profile Bootloader With SWIFT Tools With Distributor after 10 seconds with devices previously attached Profile assigned / In the mesh 4 14 Address Zero Trouble 3M Trouble dotted magnetic sensor activated/SWIFT Tools dotted magnetic sensor activated/SWIFT Tools dotted magnetic sensor activated/SWIFT Tools after 10 seconds with no devices previously attached 14 7 Rescue Mode dotted magnetic sensor activated/SWIFT Tools 5M Normal Mode/Background mesh restructuring Bootloader Firmware Update 20 M 7 1st Mesh restructuring 7 Mesh formation Legend No. of blinks square magnetic sensor activated 10 minute timout square magnetic sensor activated 10 minute timout square magnetic sensor activated 10 minute timout square magnetic sensor activated 10 minute timout square magnetic sensor activated LED color 10 minute timeout Interval between blink patterns Duration of LED state Approximate duration 14 3M Trouble with profile distribution dotted magnetic sensor activated/SWIFT Tools 14 7 Rescue Mode with profile distribution dotted magnetic sensor activated/SWIFT Tools 5M Normal Mode/Background mesh restructuring with profile distribution dotted magnetic sensor activated/SWIFT Tools 7 20 M 1st Mesh restructuring with profile distribution dotted magnetic sensor activated/SWIFT Tools 7 Mesh formation with profile distribution Example: Two blinks in this pattern 1st blink is green. 2nd is yellow 20 M 7 7 sec between blink patterns Will transition to next state after 20 minutes (approx.) All units are in seconds. Minute is indicated by M. PN LS10101-000GE-E:A 8/26/2014 14-680 2 Fold on dotted line. Fold on dotted line. Fold on dotted line. LED Table - Gateway Profile assigned / In the mesh Condition Action Required Factory default; pending magnetic sensor activation Starting up without a profile Activate either magnetic sensors within 10 seconds to create a default profile Create profile Gateway is creating a default profile LED Pattern 10 1 1 LED Pattern 3M 3M Solid Profile accepted 10 Gateway is now profile assigned 14 10 1 Profile assigned; pending magnetic sensor activations Starting up with a profile Profile removed Gateway has returned to the factory default state Activate both magnetic sensors simultaneously within 10 seconds to remove a profile 14 5 Gateway and the mesh network are searching for any device that is not in the mesh network with the same profile Rescue Mode with profile distribution Gateway and the mesh network are searching for any device that is not in the mesh network with the same profile. The gateway is also distributing a profile to any device that requests a profile Normal Mode / Background mesh restructuring Normal operation of the gateway Normal Mode/Background mesh restructuring with profile distribution Normal operation of the gateway. The gateway is also distributing a profile to any device that requests a profile 1st mesh restructuring Mesh is formed and initializing Action Required 1 5M Factory Default LED Pattern Condition Action Required Gateway is factory default Use SWIFT Tools to assign profile or activate switch to search for profile 5M Waiting for profile 10 Searching for profile 60 Rescue Mode 7 7 Condition 0.5 7 7 1st mesh restructuring with profile distribution Mesh is formed and initializing. The gateway is also distributing a profile to any device that requests a profile Mesh formation Gateway is forming the mesh and looking for devices that are not in the mesh. Wait until all devices join the mesh, and then terminate mesh formation Mesh formation with profile distribution Gateway is forming the mesh and looking for devices that are not in the mesh. The gateway is also distributing a profile to any device that requests a profile Wait until all devices join the mesh, and then terminate mesh formation 7 Gateway is factory default and requesting a profile from a distributor or another gateway Legend 7 Profile assigned / In the mesh No. of blinks LED color Interval between blink patterns Duration of LED state LED Pattern Address Zero Trouble Condition Action Required The gateway address is set to zero Ensure all devices in the mesh have a valid address. 4 LED Pattern The gateway has a trouble condition 14 Trouble with profile distribution 14 The gateway has a trouble condition. The gateway is also distributing a profile to any device that requests a profile Refer to the panel to identify the trouble and possible resolution Refer to the panel to identify the trouble and possible resolution Condition Action Required Example: Two blinks in this pattern Bootloader Normal Trouble Approximate duration Bootloader Device is ready to update 1st blink is green. 2nd is yellow 20 M 7 7 sec between blink patterns Will transition to next state after 20 minutes (approx.) Bootloader Firmware Update New application code is being downloaded All units are in seconds. Minute is indicated by M.