UNITEK DC/DC Converters ® DC-POWERCONVERSION ISOLATED DC/DC CONVERTERS DC DC converters are designed to increase, or decrease, the DC voltage that is input to the unit. The Unitek DC-Powerconversion products offers DC converters that will convert source DC into a variety of output voltages at power levels to suit your requirements. The IDC-series is a complete line of high efficiency 100, 200 or 360 Watt isolated DC-DC converters suit for applications requiring galvanic isolation between the input and the output. The isolated converters provides a highly regulated output DC voltage of 12.5, 24.5 or even 48 Vdc and rated output of 8, 15 or 30 Amp (12 Vdc models) 4, 8, 15 Amp (24 Vdc models) and 4, 7.5 Amp (48 Vdc models) IDC-100 Series IDC-200 Series IDC-360 Series INPUT VOLTAGE A Series (12Vdc nominal) 9.2-18 Vdc 9.2-18 Vdc 9.2-18 Vdc B Series (24Vdc nominal) 20-35 Vdc 20-35 Vdc 20-35 Vdc C Series (48Vdc nominal) 30-60 Vdc 30-60 Vdc 30-60 Vdc D Series (72Vdc nominal) 60-120 Vdc 60-120 Vdc 60-120 Vdc OUTPUT CURRENTS AVAILABLE 12.5Vdc 8 Amps, 100 Watts 15 Amps, 200 Watts 30 Amps, 360 Watts 24.5Vdc 4 Amps, 100 Watts 8 Amps, 200 Watts 15 Amps, 360 Watts 48.0Vdc Not available 4 Amps, 200 Watts 7,5 Amps, 360 Watts (only B & C (only B & C versions available) versions available) Output voltage regulation <2% <2% <2% Input current at no load <25Ma <25Ma <25Ma Fan assisted cooling NO YES YES Temperature increase after 25 30 30 30minutes at full load (C°) Connections Four 6.3mm push-on Four 6.3mm push-on Four 6.3mm push-on flat blade connectors flat blade connectors flat blade connectors Weight (Kgs) 0.50 0.60 1.40 Dimensions (LxWxH in mm) 152x88x49 182x88x49 160x163x64 Output ripple and noise Less than 50 mV RMS Efficiency 85% Galvanic isolation Yes>400 Vrms between input, output and case Operating ambient temp. -/- 20 C° to + 30 C° (derate linearly to zero at 70 C°) Storage temperature -/- 20 C° to + 65 C° Humidity Max 95%, non condensing Casework Anodised aluminium Protections: Overcurrent By current limiting Overheating Reduction of output voltage Reverse polarity Fuse and reverse connected diode across input Overvoltage Varistor (also protects against load dump) Approval CE and AUTOMOTIVE Warranty 2 Years UNITEK DC/DC Converters ® DC-POWERCONVERSION NON ISOLATED CONVERTERS A complete line of high quality DC/DC converters in a compact housing. This series is eminently suitable for applications requiring stability, a modest development of heat and above all a low energy consumption. These products are also distinguished by high efficiency, together with absolute safety. An inferor supply can cause irrepairable damage to your 12 Volt system, but using an Non isolated converters Input voltage Vdc Output voltage Vdc Output voltage regulation Input current at no load Output current Fan assisted cooling Temperature increase after 30 min. at full load (C°) Connections Weight (Kgs) Dimensions (LxWxH) in mm Output ripple and noise Efficiency Galvanic isolation Operating ambient temp. Storage temperature Humidity Casework Protections: Overcurrent Overheating Reverse Polarity Overvoltage Approval Warrenty SDC 05 SDC08 20-35 13,8 ± 0,1 <3% <5 mA 5 Amp No 20-35 <3% <5 mA 8 Amp No 30 20 Four 6,3mm push-on flat blade 0,17 68x88x49 Four 6,3mm push-on flat blade 0,25 98x88x49 Unitek voltage converter will prevent problems of that type. Next to the standard (non isolated) 24/12V converters, a wide range of other models is available. The SDC 20 , SDC 30 and SDC 60 can also be used as a 13.8Vdc batterycharger, to charge from a 24V system a 12V starter or accessory battery. SDC 12 SDC 20 SDC 30 SDC 60 STEP 7 STEP 10 20-35 20-35 20-35 20-35 9-18 9-18 13,6 ± 0,1 13,8 ± 0,1 13,8 ± 0,1 13,8 ± 0,1 25 ± 0,1 25 ± 0,1 <3% <3% <3% <3% +0%/-5% +0%/-5% <5 mA Aprr.25 mA Aprr.25 mA Aprr.50 mA 5 mA 5 mA 12 Amp 20 Amp 30 Amp 60 Amp 7 Amp 10 Amp No No Yes temp Yes temp No No controlled controlled 30 25 33 33 30 30 Four Four Four Terminal Four Four 6,3mm 6,3mm 6,3mm block-M6 6,3mm 6,3mm push-on push-on push-on bolt and push-on push-on flat blade flat blade flat blade Nut flat blade flat blade 0,26 0,48 0,6 1,2 0,3 0,4 98x88x49 126x88x49 151x88x49 151x88x98 98x88x49 126x88x49 less than 50 mV RMS 92% No -/- 20 C° to + 30 C° (derate linearly to zero at 70 C°) -/- 20 C° to + 65 C° Max 95%, non condensing Anodised aluminium By current limiting Reduction of output voltage Fuse and reverse connected diode across input CE and AUTOMOTIVE 2 Years