Industrial Options

advertisement
Catalog Number
Notes
Type
FEATURES & SPECIFICATIONS
HOUSING OPTIONS Shipped installed
SF Single Fuse. Use with 120, 277, 347V. Not available with Multi-tap
ballast. In-line fusing isolates faulty luminaire from circuit.
Externally accessible.
DF Double Fuse. Use with 208, 240, 480V. Not available with Multi-tap
ballast. In-line fusing isolates faulty luminaire from circuit.
Externally accessible.
EC Emergency Circuit. Factory-installed, double-contact, bayonetbase quartz socket with socket leads for use with separate
external emergency power system. (See chart at left.) (150W
maximum on acrylic opticals with lensed bottom.)
HA High Ambient. Allows the industrial luminaires to be operated in
high-ambient temperatures. TX-A30, TX-A26, TX-A20, TX-A23, TXA165: 55°C; TH-A14, TH-A15, TH-A16, TH-A17, TE, TPG, TPGE: 65°C.
QRS Quartz Restrike System. Automatically switches 120V quartz
lamp on if there is a power interruption or brownout significant
enough to cause the primary HID lamp to drop out. The 120V
quartz lamp stays on until the HID fixture restrikes. QRS does not
energize during cold start of HID luminaires. Wiring for the
quartz lamp is internal to the ballast assembly; the 120V
required to operate the quartz lamp is supplied by the ballast.
Wattage of quartz lamp should not exceed that of HID source.
(See chart at left.) (150W maximum on acrylic opticals with
lensed bottom.)
QRSTD Quartz Restrike System Time Delay. Functions as does QRS, but
120V quartz lamp energizes under hot and cold starting
conditions. Quartz lamp will come on when luminaire is
energized and remain on for two minutes after start-up or
restrike of HID lamp. Wiring for the quartz lamp is internal to the
ballast assembly; the 120V required to operate the quartz lamp
is supplied by the ballast. (See chart at left.) (150W maximum on
acrylic opticals with lensed bottom.)
MOUNTING/HOUSING OPTIONS Shipped installed
TOB Through-Wire Outlet Box. A combination outlet box and splice
compartment. Permits entry of 1-1/4" or 3/4" rigid or thin-wall
conduit through easily-removable knockouts. TOB may be
suspension or surface mounted. Height 2-7/8"; width 4-1/2".
TOBP Through-Wire Outlet Box Plug-In. Provides plug-in flexibility of
conventional power hook and reduces overall height. Female
receptacle part of TOBP box. Male plug is factory installed to
ballast housing. This option is not rated as a load break device.
Height 2-7/8"; width 4-1/2". Permits entry of rigid 3/4" or thin-wall
conduit through easily removable knockout.
PBP Pendant Box Plug-In. Pendant-mount plug-in outlet box is identical
in function to TOBP, except for pendant mounting. Height 4-1/2"
width and depth 4-1/2".
PSB Pendant Splice Box. Use with TG. Permits rigid pendant mounting.
PMB Pendant Mount Box. Use with TGL, TGR. Permits rigid pendant
mounting.
HID Lighting
Industrial
Options
SF
DF
Factory Installed
QRS
HID
Wattage
150 & below
175
250
Quartz
Wattage
Quartz Lamp Type
(Lamp by Others)
100
150
Double
Contact
Bayonet
Base
120V Lamp
250
400
250
1000
500
TOBP
TOB
PBP
PSB (TG)
PM (TGL, TGR)
Indoor H.I.D.
Sheet # OPT1
OPAC-120
OPT1 Industrial Options
REMOTE BALLAST OPTIONS Shipped installed
TR Remote Ballast. Includes ballast housing and remote optical with
RSBA or RSBB. Does not include interconnecting wiring. Add TR to
the end of fixture line item.
RSBA Remote Splice Box. Adjustable for TH A16, TH A17, TH A14, TH A15,
TH-PA22/PA25 high bay optical assemblies; 4-7/8" x 4-1/4" x 3-3/8".
RSBB Remote Splice Box. Bolt-on for TE, TX A30, TX A26, TX A20, TX A23,
TX A165, TX-PA22/PA25 and enclosed or low bay optical assemblies; 4-7/8" x 4-1/4" x 3-3/8".
RC3NP Remote Ballast with Prewired cable. Includes ballast housing
and remote optical with RPMA or RPMB and 3 feet of prewired
cable harness with Male and Female 20-amp twist lock plug
(C3NP). Add RC3NP to the end of fixture line item.
TR
RSBB
RSBA
Ballast Options Shipped installed
CWI
MRB
ENC
RLB
LLRPSL
SCWA
Constant-Wattage Isolated Ballast. 120, 208, 240V in Canada. Not
available in all fixtures. Consult factory.
Magnetic Regulator Ballast. 70–400W HPS. Not available in all voltages. Consult factory.
Encapsulated Ballast. Use with 120/277V for 175W, 250W and 400W
metal halide and 250W HPS. Not available TG/TGR.
Regulated Lag Pulse Start Ballast. Use with 175-450W metal halide
fixtures. Consult factory.
Low Loss Reactor Pulse Start Ballast. Use with 150-450W-277V
pulse start metal halide fixtures only. Consult factory.
Super Constant-Wattage Autotransformer Pulse Start Ballast. Use
with 150-1000W pulse start metal halide fixtures only. 120-480V.
Consult factory.
RC3NP
FIXTURE FINISHES
CR Corrosion-Resistant Finish. Clear polyester coating for
additional protection against some corrosive atmospheres.
Consult factory for corrosive compatibility.
CRT Corrosion-Resistant Finish. Teflon coating of all external
luminaire surfaces. Optical assemblies have a clear coat.
Ballast housing/mounting accessories are black. TE, TH A17,
TX A20, TPGE, TX A26 and TPG ballast housing only.
TEF Teflon. Finished reflectors are coated with one-mil layer of
Teflon to provide superior corrosion-resistance and ease of
maintenance. TE, TH A17, TX A20 and TX A26.
For optional architectural colors see architectural color chart for options.
Add as suffix to catalog number.
Lithonia Lighting
Sheet#: OPT1
©2001 Acuity Lighting Group, Inc. 05/06
Indoor HID
One Lithonia Way, Conyers, GA 30012
Phone: 800-315-4963, Fax: 770-602-1531
www.lithonia.com
Download