MADE IN USA - Standard Locknut
advertisement
ADAPTERS ADAPTERS FOR BEARING SERIES 230, 231, 12, 222 ADAPTERS FOR BEARING SERIES 232, 13, 223 ADAPTER SLEEVES SERIES S00, S100 ADAPTER SLEEVES SERIES S30, S31, S32 METRIC ADAPTERS SERIES H2, H3, H23, H30, H31, H32, H39 METRIC ADAPTER SLEEVES SERIES H2, H3 BearingAccessoriesandPillowBlocksCatalog METRIC ADAPTER SLEEVES SERIES H30 METRIC ADAPTER SLEEVES SERIES H31, H32 METRIC ADAPTER SLEEVES SERIES H23, H39 WITHDRAWAL SLEEVES WITHDRAWAL SLEEVES SK & ASK-SERIES DIMENSIONS WITHDRAWAL SLEEVES METRIC AH-SERIES REMOVAL NUTS LOCKNUTS REMOVAL NUTS RN SERIES DIMENSIONS LOCKNUTS N-00 SERIES DIMENSIONS LOCKNUTS N-00 SERIES SHAFT DIMENSIONS LOCKNUTS N-000 SERIES DIMENSIONS LOCKNUTS N-000 SERIES SHAFT DIMENSIONS LOCKNUTS PRN/PRL-00 SERIES DIMENSIONS (precision) LOCKNUTS PRT-00 SERIES DIMENSIONS (precision thin) LOCKNUTS SN-00 SERIES DIMENSIONS (self-locking) LOCKNUTS SNH-00 SERIES DIMENSIONS (self-locking/high temperature) LOCKNUTS NHE-00 SERIES DIMENSIONS (wide series) LOCKNUTS NIN-00 SERIES DIMENSIONS (16 threads/inch) LOCKNUTS NTH-00 SERIES DIMENSIONS (thin series) LOCKNUTS KM-00 SERIES DIMENSIONS (metric design) LOCKWASHERS LOCKWASHERS W-00 AND W-000 SERIES DIMENSIONS LOCKWASHERS PRW-00 SERIES DIMENSIONS (precision) LOCKWASHERS PRWT-00 SERIES DIMENSIONS (precision thin) LOCKWASHERS TW-000 SERIES DIMENSIONS (thick) LOCKWASHERS WTH-00 & WIN-00 SERIES DIMENSIONS (thin & inch series) LOCKWASHERS MB-00 SERIES DIMENSIONS (metric design) LOCKPLATES LOCKPLATES P-000 LOCKPLATE SERIES DIMENSIONS PILLOW BLOCKS PILLOW BLOCKS CAST IRON SAF-200 SERIES (straight bore housing) PILLOW BLOCKS CAST IRON SAF-300 SERIES (straight bore housing) PILLOW BLOCKS CAST IRON SAF-500 SERIES (tapered bore housing) PILLOW BLOCKS CAST IRON SAF-600 SERIES (tapered bore housing) PILLOW BLOCKS CAST IRON SAF-230 SERIES (tapered bore housing) PILLOW BLOCKS STEEL SAFS-200 SERIES (straight bore housing) PILLOW BLOCKS STEEL SAFS-500 SERIES (tapered bore housing) MILITARY STANDARD MILITARY STANDARD LOCKNUTS MS 1722 SERIES MILITARY STANDARD LOCKWASHERS MS 1722 SERIES MILITARY STANDARD LOCKNUTS MS 19067 SERIES MILITARY STANDARD LOCKWASHERS MS 19069 SERIES MILITARY STANDARD LOCKNUTS MS 19068 SERIES MILITARY STANDARD LOCKWASHERS MS 19070 SERIES SPANNER WRENCHES SPANNER WRENCHES RETHREADING DIES RETHREADING DIES DRT-SERIES CLAMP NUTS CLAMP NUTS NC-SERIES X WASHERS X-WASHERS MADE IN USA BearingAccessoriesand PillowBlocksCatalog 2 We are recognized in the bearing industry as the premier supplier of bearing accessories including adapters, locknuts, lockwashers, seal rings, adapter sleeves and, of course, split pillow blocks. Since 1948, Standard Locknut, LLC has been supporting key industries like the bearing, oil and gas, aerospace, mining, chemical, heavy duty and offroad, with the highest quality and on-time delivery of bearing accessories. Made in the USA, you can count on it. We supply our standard split pillow blocks to all corners of the globe. Typically used with a spherical bearing, the housing may be your most important purchase. It all starts with the castings. We control our quality of pillow blocks by using castings from molds designed and owned by us. We supply the industry in sizes from 511 up to 056 in SAF and SAFS. Cast iron, ductile iron or steel, along with the LER seals, we’re prepared to support your pillow block needs. We also machine customer-supplied pillow blocks, both standard and specials, for those unique and demanding applications. Either way, our customers have come to depend on us for our reliability, quality and delivery. Critical to any successful bearing installation is the means of securing the bearing to the shaft. That’s where we come in. Our line of locking devices includes adapters and sleeves, washers, locknuts and lockwashers. Available in metric and inch series, our accessories are manufactured to ABMA, SAE and ABEC standards. TS19649 AS9100 Certified Standard Locknut, LLC “We will meet or exceed all customer expectaƟons and conƟnually improve everything we do.” CONTACT US TODAY Sales: ......................... (800) 783-6887 Fax: ............................ (800) 573-5515 Email: ........................ sales@stdlocknut.com www.standardlocknut.com 1045 East 169th Street Westfield, IN 46074 5 6 7 ADAPTER SERIES FOR BEARING SERIES 230, 231, 12, 222 For tapered bore assembly BEARING NOMINAL BORE (mm) 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 120 130 140 150 160 170 180 190 200 220 240 260 280 300 320 340 360 380 400 420 440 460 480 500 530 560 600 630 670 710 750 800 850 900 950 230 231 ADAPTER UNIT ASSEMBLY ASSEMBLY SLEEVE NO. WT. (LB.) NO. ADAPTER UNIT ASSEMBLY ASSEMBLY SLEEVE NO. WT. (LB.) NO. SNW-3024 SNW-3026 SNW-3028 SNW-3030 SNW-3032 SNW-3034 SNW-3036 SNW-3038 SNW-3040 SNW-3044 SNP-3048 SNP-3052 SNP-3056 SNP-3060 SNP-3064 SNP-3068 SNP-3072 SNP-3076 SNP-3080 SNP-3084 SNP-3088 SNP-3092 SNP-3096 SNP-30/500 SNP-30/530 SNP-30/560 SNP-30/600 SNP-30/630 SNP-30/670 SNP-30/710 SNP-30/750 SNP-30/800 SNP-30/850 SNP-30/900 SNP-30/950 6.16 7.50 8.45 9.80 12.00 13.50 15.00 16.50 19.50 24.50 32.00 41.00 45.50 59.00 65.00 78.00 86.00 94.50 100.00 105.00 S-3024 S-3026 S-3028 S-3030 S-3032 S-3034 S-3036 S-3038 S-3040 S-3044 S-3048 S-3052 S-3056 S-3060 S-3064 S-3068 S-3072 S-3076 S-3080 S-3084 S-3088 S-3092 S-3096 S-30/500 S-30/530 S-30/560 S-30/600 S-30/630 S-30/670 S-30/710 S-30/750 S-30/800 S-30/850 S-30/900 S-30/950 SNW-3122 SNW-3124 SNW-3126 SNW-3128 SNW-3130 SNW-3132 SNW-3134 SNW-3136 SNW-3138 SNW-3140 SNW-3144 SNP-3148 SNP-3152 SNP-3156 SNP-3160 SNP-3164 SNP-3168 SNP-3172 SNP-3176 SNP-3180 SNP-3184 SNP-3188 SNP-3192 SNP-3196 SNP-31/500 SNP-31/530 SNP-31/560 SNP-31/600 SNP-31/630 SNP-31/670 SNP-31/710 SNP-31/750 SNP-31/800 SNP-31/850 4.25 5.85 8.35 8.35 13.50 13.50 16.00 17.00 19.50 28.50 32.00 37.50 44.00 46.50 59.50 74.00 93.50 120.00 125.00 140.00 145.00 230 & 231 S-22 S-24 S-26 S-28 S-30 S-32 S-34 S-36 S-38 S-40 S-44 S-48 S-52 S-3156 S-3160 S-3164 S-3168 S-3172 S-3176 S-3180 S-3184 S-3188 S-3192 S-3196 S-31/500 S-31/530 S-31/560 S-31/600 S-31/630 S-31/670 S-31/710 S-31/750 S-31/800 S-31/850 12 222 12 & 222 ADAPTER UNIT ADAPTER UNIT LOCKNUT LOCKING ASSEMBLY ASSEMBLY SLEEVE ASSEMBLY ASSEMBLY SLEEVE LOCKNUT LOCKING NO. DEVICE NO. NO. WT. (LB.) NO. NO. WT. (LB.) NO. NO. DEVICE NO. SNW-04 S-04 SNW-05 0.17 S-05 SNW-06 0.24 S-06 SNW-07 0.32 S-07 SNW-07 0.32 S-07 N-07 W-07 SNW-08 0.42 S-08 SNW-08 0.42 S-08 N-08 W-08 SNW-09 0.55 S-09 SNW-09 0.55 S-09 N-09 W-09 SNW-10 0.67 S-10 SNW-10 0.67 S-10 N-10 W-10 SNW-11 0.77 S-11 SNW-11 0.77 S-11 N-11 W-11 SNW-12 0.87 S-12 SNW-12 0.87 S-12 N-12 W-12 SNW-13 1.01 S-13 SNW-13 1.01 S-13 N-13 W-13 SNW-14 1.59 S-14 SNW-14 1.59 S-14 N-14 W-14 SNW-15 1.83 S-15 SNW-15 1.83 S-15 AN-15 W-15 SNW16 2.27 S-16 SNW-16 2.27 S-16 AN-16 W-16 SNW-17 2.60 S-17 SNW-17 2.60 S-17 AN-17 W-17 SNW-18 3.02 S-18 SNW-18 3.02 S-18 AN-18 W-18 SNW-19 3.44 S-19 AN-19 W-19 SNW-20 3.37 S-20 SNW-20 3.73 S-20 AN-20 W-20 N-022 N-024 N-026 N-028 N-030 N-032 N-034 N-036 N-038 N-040 N-044 N-048 N-052 N-056 N-060 N-064 N-068 N-072 N-076 N-080 N-084 N-088 N-092 N-096 N-500 N-530 N-560 N-600 N-630 N-670 N-710 N-750 N-800 N-850 N-900 N-950 W-022 W-024 W-026 W-028 W-030 W-032 W-034 W-036 W-038 W-040 W-044 P-48 P-52 P-56 P-60 P-64 P-68 P-72 P-76 P-80 P-84 P-88 P-92 P-96 P-500 P-530 P-560 P-600 P-630 P-670 P-710 P-750 P-800 P-850 P-900 P-950 ADAPTER SERIES 8 SNW-22 4.81 S-22 SNW-22 SNW-24 SNW-26 SNW-28 SNW-30 SNW-32 SNW-34 SNW-36 SNW-38 SNW-40 SNW-44 SNP-48 SNP-52 4.81 6.65 9.70 10.50 16.00 15.50 19.50 20.50 23.50 30.50 32.50 S-22 S-24 S-26 S-28 S-30 S-32 S-34 S-36 S-38 S-40 S-44 S-48 S-52 AN-22 AN-24 AN-26 AN-28 AN-30 AN-32 AN-34 AN-36 AN-38 AN-40 N-044 N-048 N-052 W-22 W-24 W-26 W-28 W-30 W-32 W-34 W-36 W-38 W-40 W-44 P-48 P-52 ADAPTER SERIES FOR BEARING SERIES 232, 13, 223 For tapered bore assembly BEARING NOMINAL BORE (mm) 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 120 130 140 150 160 170 180 190 200 220 240 260 280 300 320 340 360 380 400 420 440 460 480 500 530 560 600 630 670 710 750 ASSEMBLY NO. 232 13 ADAPTER UNIT ASSEMBLY WT. (LB.) ADAPTER UNIT ASSEMBLY WT. (LB.) SLEEVE NO. SNW-120 4.75 S-120 SNW-122 SNW-124 SNW-126 SNW-128 SNW-130 SNW-132 SNW-134 SNW-136 SNW-138 SNW-140 SNW-144 SNP-148 SNP-152 SNP-3256 SNP-3260 SNP-3264 SNP-3268 SNP-3272 SNP-3276 SNP-3280 SNP-3284 SNP-3288 SNP-3292 SNP-3296 SNP-32/500 SNP-32/530 SNP-32/560 SNP-32/600 SNP-32/630 SNP-32/670 SNP-32/719 SNP-32/750 6.04 7.03 10.10 12.20 14.60 20.20 22.50 24.90 27.80 30.60 36.80 48.50 54.50 59.00 68.50 98.00 105.00 135.00 145.00 165.00 195.00 S-122 S-124 S-126 S-128 S-130 S-132 S-134 S-136 S-138 S-140 S-144 S-148 S-152 S-3256 S-3260 S-3264 S-3268 S-3272 S-3276 S-3280 S-3284 S-3288 S-3292 S-3296 S-32/500 S-32/530 S-32/560 S-32/600 S-32/630 S-32/670 S-32/710 S-32/750 ASSEMBLY NO. SNW-04 SNW-05 SNW-06 SNW-07 SNW-08 SNW-09 SNW-10 SNW-11 SNW-12 SNW-13 SNW-14 SNW-15 SNW-16 SNW-17 SNW-18 SNW-19 SNW-20 SNW-21 SNW-22 223 0.17 0.24 0.32 0.42 0.55 0.67 0.77 0.87 1.01 1.59 1.83 2.27 2.60 3.02 3.44 3.73 4.30 4.81 SLEEVE NO. S-04 S-05 S-06 S-07 S-08 S-09 S-10 S-11 S-12 S-13 S-14 S-15 S-16 S-17 S-18 S-19 S-20 S-21 S-22 232, 13 & 223 ASSEMBLY NO. ADAPTER UNIT ASSEMBLY WT. (LB.) SLEEVE NO. SNW-108 SNW-109 SNW-110 SNW-111 SNW-112 SNW-113 SNW-114 SNW-115 SNW-116 SNW-117 SNW-118 SNW-119 SNW-120 0.50 0.62 0.80 0.93 1.06 1.23 1.59 2.32 2.82 3.20 3.73 4.23 4.74 S-108 S-109 S-110 S-111 S-112 S-113 S-114 S-115 S-116 S-117 S-118 S-119 S-120 SNW-122 SNW-124 SNW-126 SNW-128 SNW-130 SNW-132 SNW-134 SNW-136 SNW-138 SNW-140 SNW-144 SNW-148 SNW-152 6.04 7.03 10.10 12.20 14.60 20.20 22.50 24.90 27.80 30.60 36.80 48.50 54.50 S-122 S-124 S-126 S-128 S-130 S-132 S-134 S-136 S-138 S-140 S-144 S-148 S-152 LOCKNUT NO. N-04 N-05 N-06 N-07 N-08 N-09 N-10 N-11 N-12 N-13 N-14 AN-15 AN-16 AN-17 AN-18 AN-19 AN-20 AN-21 AN-22 AN-24 AN-26 AN-28 AN-30 AN-32 AN-34 AN-36 AN-38 AN-40 N-44 N-048 N-052 N-056 N-060 N-064 N-068 N-072 N-076 N-080 N-084 N-088 N-092 N-096 N-500 N-530 N-560 N-600 N-630 N-670 N-710 N-750 LOCKING DEVICE NO. W-04 W-05 W-06 W-07 W-08 W-09 W-10 W-11 W-12 W-13 W-14 W-15 W-16 W-17 W-18 W-19 W-20 W-21 W-22 W-24 W-26 W-28 W-30 W-32 W-34 W-36 W-38 W-40 W-44 P-48 P-52 P-56 P-60 P-64 P-68 P-72 P-76 P-80 P-84 P-88 P-92 P-96 P-500 P-530 P-560 P-600 P-630 P-670 P-710 P-750 ADAPTER SERIES 9 ADAPTER SLEEVE SERIES S00 SERIES FOR BEARING SERIES 12, 13, 222, 231 S100 SERIES FOR BEARING SERIES 223, 232 For tapered bore assembly ADAPTER SLEEVE DIMENSIONS SLEEVE NO. BORE DIA. d MAX. S00 S04 S05 S06 S07 S08 S09 S10 S11 S12 S13 S14 S15 S16 S17 S18 S19 S20 S21 S22 S24 S26 S28 S30 S32 S34 S36 S38 S40 S44 S48 S52 S100 S104 S105 S106 S107 S108 S109 S110 S111 S112 S113 S114 S115 S116 S117 S118 S119 S120 S121 S122 S124 S126 S128 S130 S132 S134 S136 S138 S140 S144 S148 S152 0.692 0.754 0.942 1.192 1.317 1.442 1.692 1.942 2.067 2.192 2.317 2.442 2.692 2.942 3.192 3.317 3.442 3.692 3.942 4.192 4.442 4.942 5.192 5.442 5.942 6.442 6.942 7.192 7.942 8.942 9.442 SHARP CORNER DIA. A MIN. S00 0.855 1.052 1.256 1.459 1.659 1.863 2.070 2.273 2.480 2.683 2.894 3.090 3.293 3.497 3.700 3.904 4.107 4.314 4.524 4.937 5.350 5.757 6.167 6.584 6.997 7.404 7.814 8.221 9.041 9.878 10.734 S100 0.875 1.082 1.292 1.499 1.702 1.909 2.122 2.329 2.535 2.739 2.950 3.155 3.362 3.566 3.776 3.982 4.199 4.412 4.619 5.035 5.452 5.869 6.282 6.696 7.109 7.522 7.939 8.355 9.153 9.994 10.832 SLEEVE LENGTH L MIN. S00 1.224 1.259 1.343 1.449 1.494 1.574 1.755 1.835 1.979 2.090 2.264 2.286 2.366 2.476 2.636 2.750 2.859 2.977 3.196 3.456 3.752 3.971 4.231 4.568 4.837 5.028 5.251 5.474 5.891 6.628 7.583 THREADS MAX. K1 THD. LENGTH G MAX. 0.781 0.969 1.173 1.376 1.563 1.767 1.967 2.157 2.360 2.548 2.751 2.933 3.137 3.340 3.527 3.730 3.918 4.122 4.325 4.716 5.106 5.497 5.888 6.284 6.659 7.066 7.472 7.847 8.628 9.422 10.192 32 32 18 18 18 18 18 18 18 18 18 12 12 12 12 12 12 12 12 12 12 12 12 8 8 8 8 8 8 6 6 0.531 0.570 0.632 0.664 0.672 0.672 0.734 0.739 0.770 0.802 0.802 0.905 0.905 0.936 1.020 1.051 1.083 1.083 1.145 1.176 1.239 1.301 1.364 1.520 1.551 1.583 1.614 1.676 1.708 1.989 2.135 MAJOR DIA. B S100 1.460 1.617 1.779 1.922 2.005 2.123 2.384 2.506 2.649 2.761 2.935 3.074 3.194 3.302 3.543 3.692 3.961 4.157 4.338 4.638 4.972 5.313 5.611 5.910 6.178 6.446 6.748 7.085 7.277 8.099 8.764 ADAPTER SLEEVE SERIES 10 WIDTH F SLOT WIDTH P DEPTH T MIN. MIN. MIN. 0.07 0.07 0.07 0.07 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.15 0.15 0.15 0.15 0.15 0.15 0.24 0.24 0.24 0.24 0.24 0.30 0.30 0.240 0.240 0.240 0.240 0.365 0.365 0.365 0.365 0.365 0.365 0.365 0.365 0.428 0.428 0.428 0.428 0.428 0.428 0.428 0.428 0.552 0.740 0.740 0.740 0.865 0.865 0.865 0.990 0.990 1.125 1.188 0.691 0.741 0.822 0.863 0.874 0.874 0.954 0.961 1.001 1.043 1.043 1.177 1.177 1.217 1.326 1.367 1.408 1.408 1.488 1.529 1.611 1.692 1.774 1.976 2.017 2.058 2.098 2.179 2.220 0.500 0.500 ADAPTER SLEEVE SERIES S3000 SERIES FOR BEARING SERIES 230 S3100 SERIES FOR BEARING SERIES 231 S3200 SERIES FOR BEARING SERIES 232 For tapered bore assembly ADAPTER SLEEVE DIMENSIONS SLEEVE NO. BORE DIA. SHARP CORNER DIA. A MIN. d MAX. S3000 S3024 S3026 S3028 S3030 S3032 S3034 S3036 S3038 S3040 S3044 S3048 S3052 S3056 S3060 S3064 S3068 S3072 S3076 S3080 S3084 S3088 S3092 S3096 S30/500 S30/530 S30/560 S30/600 S30/630 S30/670 S30/710 S30/750 S30/800 S30/850 S30/900 S30/950 S3100 S3156 S3160 S3164 S3168 S3172 S3176 S3180 S3184 S3188 S3192 S3196 S31/500 S31/530 S31/560 S31/600 S31/630 S31/670 S31/710 S31/750 S31/800 S31/850 S3200 S3256 S3260 S3264 S3268 S3272 S3276 S3280 S3284 S3288 S3292 S3296 S32/500 S32/530 S32/560 S32/600 S32630 S32/670 S32/710 S32/750 4.192 4.442 4.942 5.192 5.442 5.942 6.442 6.942 7.192 7.942 8.942 9.444 10.444 10.944 11.944 12.444 13.444 13.944 15.006 15.756 16.506 17.006 18.006 18.506 19.506 21.006 22.006 24.006 25.006 26.506 28.006 29.506 31.506 33.506 36.506 S3000 4.890 5.304 5.701 6.105 6.512 6.929 7.346 7.744 8.161 8.976 9.771 10.600 11.394 12.221 13.020 13.847 14.639 15.430 16.260 17.056 17.868 18.675 19.469 20.263 21.507 22.721 24.316 25.537 27.175 28.769 30.394 32.389 34.407 36.402 38.438 S3100 11.526 12.359 13.201 14.034 14.829 15.623 16.430 17.298 18.094 18.928 19.741 20.581 21.793 23.000 24.644 25.875 27.522 29.127 30.771 32.772 34.827 SLEEVE LENGTH L MIN. S3200 11.624 12.464 13.306 14.146 14.960 15.774 16.614 17.456 18.271 19.111 19.945 20.817 22.065 23.279 24.933 26.193 27.857 29.471 31.132 S3000 2.937 3.227 3.330 3.482 3.701 4.009 4.327 4.402 4.740 5.120 5.422 6.009 6.181 6.717 6.936 7.533 7.569 7.733 8.401 8.488 9.100 9.336 9.446 9.838 10.579 11.222 11.451 11.924 12.835 13.509 14.093 14.408 14.991 15.681 16.492 S3100 7.756 8.370 9.101 9.777 9.852 10.056 10.449 11.402 11.817 12.368 12.714 13.657 14.004 14.569 15.388 15.979 17.008 17.801 18.620 19.014 20.030 MAJOR DIA B MAX. THREADS NO. PER INCH K1 M1 S3200 8.937 9.630 10.361 11.116 11.427 11.867 12.654 13.292 13.943 14.573 15.155 16.491 17.271 17.915 18.853 19.798 21.024 21.935 22.982 4.716 5.106 5.497 5.888 6.284 6.659 7.066 7.472 7.847 8.628 9.442 10.192 11.004 11.785 12.562 13.303 14.134 14.921 15.709 16.496 17.283 18.071 18.858 19.646 20.827 22.008 23.583 24.764 26.339 27.914 29.489 31.457 33.426 35.394 37.363 12 12 12 12 8 8 8 8 8 8 6 6 6 6 6 5 5 5 5 5 5 5 5 5 4 4 4 4 4 3 3 3 3 3 3 THD. LENGTH G MAX. S3000 1.260 1.323 1.385 1.416 1.478 1.510 1.541 1.604 1.666 1.760 1.978 2.135 2.229 2.291 2.385 2.541 2.541 2.666 2.823 2.823 3.228 3.228 3.260 3.573 3.573 3.823 3.916 3.916 4.104 4.541 4.541 4.541 4.573 4.948 4.948 WIDTH F MIN. SLOT WIDTH P MIN. DEPTH T MIN. 0.146 0.146 0.146 0.146 0.146 0.240 0.240 0.240 0.240 0.240 0.302 0.302 0.302 0.302 0.302 0.302 0.365 0.365 0.365 0.365 0.365 0.365 0.365 0.365 0.490 0.490 0.490 0.490 0.490 0.490 0.490 0.490 0.490 0.490 0.490 0.428 0.552 0.740 0.740 0.740 0.865 0.865 0.865 0.990 0.990 1.125 1.188 1.250 1.375 1.438 1.500 1.500 1.500 1.625 1.625 1.812 1.812 1.812 1.812 1.812 1.812 1.812 2.000 2.000 2.000 2.000 2.000 2.000 2.000 2.000 1.638 1.720 1.800 1.892 1.921 1.963 2.003 2.085 2.166 2.288 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.625 0.625 0.625 0.625 0.625 0.625 0.625 S3100 2.229 2.291 2.385 2.541 2.541 2.666 2.885 2.948 3.228 3.323 3.354 3.666 3.666 3.916 3.916 3.916 4.104 4.635 4.635 4.635 4.760 ADAPTER SLEEVE SERIES 11 METRIC ADAPTER SERIES ADAPTER SERIES H2, H3, H23, H30, H31, H32, H39 Adapter assemblies Metric Locknut Number For tapered bore assembly ADAPTER DIMENSIONS BEARING BORE DIA. (mm) 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 120 130 140 150 160 170 180 190 200 220 240 260 280 300 320 340 360 380 400 420 440 460 480 500 ADAPTER SERIES H2 H204 H205 H206 H207 H208 H209 H210 H211 H212 H213 H214 H215 H216 H217 H218 H219 H220 H221 H222 H3 H304 H305 H306 H307 H308 H309 H310 H311 H312 H313 H314 H315 H316 H317 H318 H319 H320 H321 H322 H23 H2304 H2305 H2306 H2307 H2308 H2309 H2310 H2311 H2312 H2313 H2314 H2315 H2316 H2317 H2318 H2319 H2320 H2321 H2322 H2324 H2326 H2328 H2330 H2332 H2334 H2336 H2338 H2340 H2344 H2348 H2352 H2356 LOCKNUT NO. H31 H32 H3120 H3122 H3124 H3126 H3128 H3130 H3132 H3134 H3136 H3138 H3140 H3144 H3148 H3152 H3156 H3160 H3164 H3168 H3172 H3176 H3180 H3184 H3188 H3192 H3196 H31/500 BEARING BORE DIA. H3260 H3264 H3268 H3272 H3276 H3280 H3284 H3288 H3292 H3296 H32/500 ADAPTER SERIES H30 KM4 MB84 KM5 MB85 KM6 MB86 KM7 MB87 KM8 MB88 KM9 MB9 KM10 MB10 KM11 MB11 KM12 MB12 KM13 MB13 KM14 MB14 KM15 MB15 KM16 MB16 KM17 MB17 KM18 MB18 KM19 MB19 KM20 MB20 KM21 MB21 KM22 MB22 KM24 MB24 KM26 MB26 KM28 MB28 KM30 MB30 KM32 MB32 KM34 MB34 KM36 MB36 KM38 MB38 KM40 MB40 HM44T MB44 HM48T MB48 HM52T MB52 HM56T MB56 HM3160 MS3160 HM3164 MS3164 HM3168 MS3168 HM3172 MS3172 HM3176 MS3176 HM3180 MS3180 HM3184 MS3184 HM3188 MS3188 HM3192 MS3192 HM3196 MS3196 HM31/500 MS31/500 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 120 130 140 150 160 170 180 190 200 220 240 260 280 300 320 340 360 380 400 420 440 460 480 500 METRIC ADAPTER SERIES 12 H3024 H3026 H3028 H3030 H3032 H3034 H3036 H3038 H3040 H3044 H3048 H3052 H3056 H3060 H3064 H3068 H3072 H3076 H3080 H3084 H3088 H3092 H3096 H30/500 LOCKNUT NO. LOCKING BEARING DEVICE NO. BORE DIA. H39 H3924 H3926 H3928 H3930 H3932 H3934 H3936 H3938 H3940 H3944 H3948 H3952 H3956 H3960 H3964 H3968 H3972 H3976 H3980 H3984 H3988 H3992 H3996 H39/500 KML24 KML26 KML28 KML30 KML32 KML34 KML36 KML38 KML40 HM3044 HM3048 HM3052 HM3056 HM3060 HM3064 HM3068 HM3072 HM3076 HM3080 HM3084 HM3088 HM3092 HM3096 HM30/500 MBL24 MBL26 MBL28 MBL30 MBL32 MBL34 MBL36 MBL38 MBL40 MS3044 MS3048 MS3052 MS3056 MS3060 MS3064 MS3068 MS3072 MS3076 MS3080 MS3084 MS3088 MS3092 MS3096 MS30/500 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 120 130 140 150 160 170 180 190 200 220 240 260 280 300 320 340 360 380 400 420 440 460 480 500 METRIC SLEEVE SERIES ADAPTER SERIES H2, H3 For tapered bore assembly SERIES H2 METRIC ADAPTER SLEEVE DIMENSIONS SLEEVE NO. H204 H205 H206 H207 H208 H209 H210 H211 H212 H213 H214 H215 H216 H217 H218 H219 H220 H221 H222 BORE DIA. d NOM. 0.669 0.787 0.984 1.181 1.378 1.575 1.772 1.968 2.165 2.362 2.362 2.559 2.756 2.953 3.150 3.346 3.543 3.740 3.937 SHARP CORNER DIA. A MIN. 0.843 1.043 1.240 1.441 1.642 1.843 2.043 2.244 2.445 2.646 2.846 3.047 3.244 3.453 3.654 3.858 4.063 4.264 4.468 SLEEVE LENGTH L MAX. 0.945 1.024 1.063 1.142 1.220 1.299 1.378 1.457 1.496 1.575 1.614 1.693 1.811 1.968 2.047 2.165 2.283 2.362 2.480 THREADS THD. LENGTH G MIN. M20 X 1 0.433 M25 X 1.5 0.512 M30 X 1.5 0.512 M35 X 1.5 0.551 M40 X 1.5 0.591 M45 X 1.5 0.630 M50 X 1.5 0.669 M55 X 2 0.709 M60 X 2 0.709 M65 X 2 0.748 M70 X 2 0.787 M75 X 2 0.827 M80 X 2 0.906 M85 X 2 0.984 M90 X 2 0.984 M95 X 2 1.024 M100 X 2 1.063 M105 X 2 1.063 M110 X 2 1.102 METRIC THREADS WIDTH F SLOT WIDTH P DEPTH T MIN. 0.059 0.079 0.079 0.079 0.079 0.079 0.079 0.098 0.098 0.098 0.098 0.118 0.118 0.118 0.118 0.118 0.118 0.118 0.118 MIN. 0.197 0.236 0.236 0.276 0.276 0.276 0.276 0.354 0.354 0.354 0.354 0.354 0.433 0.433 0.433 0.433 0.512 0.512 0.512 MIN. 0.512 0.630 0.630 0.669 0.709 0.748 0.787 0.827 0.827 0.866 0.945 0.984 1.063 1.142 1.142 1.181 1.220 1.220 1.260 WIDTH F SLOT WIDTH P DEPTH T MIN. 0.059 0.079 0.079 0.079 0.079 0.079 0.079 0.098 0.098 0.098 0.098 0.118 0.118 0.118 0.118 0.118 0.118 0.118 0.118 MIN. 0.197 0.236 0.236 0.276 0.276 0.276 0.276 0.354 0.354 0.354 0.354 0.354 0.433 0.433 0.433 0.433 0.512 0.512 0.512 MIN. 0.512 0.630 0.630 0.669 0.709 0.748 0.787 0.827 0.827 0.866 0.945 0.984 1.063 1.142 1.142 1.181 1.220 1.220 1.260 SERIES H3 METRIC ADAPTER SLEEVE DIMENSIONS SLEEVE NO. H304 H305 H306 H307 H308 H309 H310 H311 H312 H313 H314 H315 H316 H317 H318 H319 H320 H321 H322 BORE DIA. d NOM. 0.669 0.787 0.984 1.181 1.378 1.575 1.772 1.968 2.165 2.362 2.362 2.559 2.756 2.953 3.150 3.346 3.543 3.740 3.937 SHARP CORNER DIA. A MIN. 0.858 1.051 1.256 1.461 1.657 1.862 2.067 2.272 2.476 2.677 2.882 3.087 3.287 3.496 3.697 3.902 4.102 4.311 4.516 SLEEVE LENGTH L MAX. 1.102 1.142 1.220 1.378 1.417 1.535 1.654 1.772 1.850 1.968 2.047 2.165 2.323 2.480 2.559 2.677 2.795 2.913 3.031 THREADS THD. LENGTH G MIN. M20 X 1 0.433 M25 X 1.5 0.512 M30 X 1.5 0.512 M35 X 1.5 0.551 M40 X 1.5 0.591 M45 X 1.5 0.630 M50 X 1.5 0.669 M55 X 2 0.709 M60 X 2 0.709 M65 X 2 0.748 M70 X 2 0.787 M75 X 2 0.827 M80 X 2 0.906 M85 X 2 0.984 M90 X 2 0.984 M95 X 2 1.024 M100 X 2 1.063 M105 X 2 1.063 M110 X 2 1.102 METRIC THREADS METRIC SLEEVE SERIES 13 METRIC SLEEVE SERIES ADAPTER SERIES H30 For tapered bore assembly SERIES H30 METRIC ADAPTER SLEEVE DIMENSIONS SLEEVE NO. H3024 H3026 H3028 H3030 H3032 H3034 H3036 H3038 H3040 H3044 H3048 H3052 H3056 H3060 H3064 H3068 H3072 H3076 H3080 H3084 H3088 H3092 H3096 H30/500 BORE DIA. d NOM. 4.331 4.528 4.921 5.315 5.512 5.906 6.299 6.693 7.087 7.874 8.661 9.449 10.236 11.024 11.811 12.598 13.386 14.173 14.961 15.478 16.142 16.929 17.717 18.504 SHARP CORNER DIA. A MIN. 4.890 5.307 5.701 6.106 6.516 6.929 7.346 7.748 8.165 8.976 9.772 10.598 11.398 12.224 13.024 13.850 14.642 15.437 16.268 17.059 17.874 18.681 19.480 20.272 SLEEVE LENGTH L MAX. 2.835 3.150 3.228 3.425 3.661 3.976 4.291 4.409 4.724 4.961 5.236 5.709 5.984 6.614 6.732 7.362 7.402 7.598 8.268 8.346 8.976 9.213 9.331 9.724 METRIC THREADS M120 X 2 M130 X 2 M140 X 2 M150 X 2 M160 X 3 M170 X 3 M180 X 3 M190 X 3 M200 X 3 TR220 X 4 TR240 X 4 TR260 X 4 TR280 X 4 TR300 X 4 TR320 X 5 TR340 X 5 TR360 X 5 TR380 X 5 TR400 X 5 TR420 X 5 TR440 X 5 TR460 X 5 TR480 X 5 TR500 X 5 THREADS THD. LENGTH G MIN. 1.142 1.220 1.260 1.339 1.417 1.457 1.496 1.575 1.614 1.535 1.693 1.732 1.890 2.047 2.037 2.205 2.205 2.362 2.520 2.520 2.874 2.874 2.874 3.189 METRIC SLEEVE SERIES 14 WIDTH F SLOT WIDTH P DEPTH T MIN. 0.197 0.197 0.197 0.197 0.236 0.236 0.236 0.236 0.236 0.197 0.315 0.315 0.315 0.315 0.315 0.315 0.394 0.394 0.394 0.394 0.394 0.394 0.394 0.394 MIN. 0.591 0.591 0.669 0.669 0.748 0.748 0.827 0.827 0.827 0.787 0.787 0.787 0.945 0.945 0.945 0.945 1.102 1.102 1.102 1.260 1.260 1.260 1.417 1.417 MIN. 1.339 1.417 1.457 1.535 1.654 1.693 1.732 1.811 1.850 0.827 0.827 0.866 0.866 0.866 0.984 1.024 1.024 1.024 1.063 1.063 1.063 1.102 1.102 1.102 METRIC SLEEVE SERIES ADAPTER SERIES H31, H32 For tapered bore assembly SERIES H31 and H32 METRIC ADAPTER SLEEVE DIMENSIONS SLEEVE NO. H3120 H3122 H3124 H3126 H3128 H3130 H3132 H3134 H3136 H3138 H3140 H3144 H3148 H3152 H3156 H3160 H3164 H3168 H3172 H3176 H3180 H3184 H3188 H3192 H3196 H31/500 H3260 H3264 H3268 H3272 H3276 H3280 H3284 H3288 H3292 H3296 H32/500 BORE DIA. d NOM. 3.543 3.937 4.331 4.528 4.921 5.315 5.512 5.906 6.299 6.693 7.087 7.874 8.661 9.449 10.236 11.024 11.811 12.598 13.386 14.173 14.961 15.748 16.142 16.929 17.717 18.504 11.024 11.811 12.598 13.386 14.173 14.961 15.748 16.142 16.929 17.717 18.504 SHARP CORNER DIA. A MIN. 4.122 4.528 4.941 5.346 5.752 6.185 6.598 7.000 7.421 7.843 8.264 9.075 9.890 10.732 11.528 12.362 13.201 14.039 14.831 15.630 16.437 17.303 18.098 19.287 19.752 20.591 12.469 13.307 14.150 14.965 15.780 16.622 17.461 18.280 19.118 19.953 20.472 SLEEVE LENGTH L MAX. 2.992 3.189 3.465 3.622 3.819 4.370 4.685 4.803 5.157 5.551 5.906 6.339 6.772 7.480 7.677 8.189 8.898 10.000 10.197 10.394 10.709 11.968 12.087 12.835 13.189 14.016 9.449 10.157 11.339 11.772 12.205 12.913 13.858 14.213 15.039 15.630 16.850 METRIC THREADS M100 X 2 M110 X 2 M120 X 2 M130 X 2 M140 X 2 M150 X 2 M160 X 3 M170 X 3 M180 X 3 M190 X 3 M200 X 3 TR220 X 4 TR240 X 4 TR260 X 4 TR280 X 4 TR300 X 4 TR320 X 5 TR340 X 5 TR360 X 5 TR380 X 5 TR400 X 5 TR420 X 5 TR440 X 5 TR460 X 5 TR480 X 5 TR500 X 5 TR300 X 4 TR320 X 5 TR340 X 5 TR360 X 5 TR380 X 5 TR400 X 5 TR420 X 5 TR440 X 5 TR460 X 5 TR480 X 5 TR500 X 5 THREADS THD. LENGTH G MIN. 1.063 1.102 1.142 1.220 1.260 1.339 1.417 1.457 1.496 1.575 1.614 1.732 1.811 1.929 2.008 1.968 2.087 2.598 2.717 2.835 2.913 3.228 3.268 3.465 3.465 3.661 1.968 2.087 2.598 2.717 2.835 2.913 3.228 3.268 3.465 3.465 3.661 WIDTH F SLOT WIDTH P DEPTH T MIN. 0.118 0.118 0.197 0.197 0.197 0.197 0.236 0.236 0.236 0.236 0.236 0.236 0.236 0.315 0.315 0.315 0.315 0.315 0.394 0.394 0.394 0.394 0.394 0.394 0.394 0.394 0.315 0.315 0.315 0.394 0.394 0.394 0.394 0.394 0.394 0.394 0.394 MIN. 0.512 0.512 0.591 0.591 0.669 0.669 0.748 0.748 0.827 0.827 0.827 0.984 0.984 1.142 1.142 0.945 0.945 1.102 1.102 1.260 1.260 1.260 1.417 1.417 1.417 1.575 0.945 0.945 1.102 1.102 1.260 1.260 1.260 1.417 1.417 1.417 1.575 MIN. 1.220 1.260 1.339 1.417 1.457 1.535 1.654 1.693 1.732 1.811 1.850 2.008 2.087 2.205 2.283 0.866 0.984 1.024 1.024 1.024 1.063 1.063 1.063 1.102 1.102 1.102 0.866 0.984 1.024 1.024 1.024 1.063 1.063 1.063 1.102 1.102 1.102 METRIC SLEEVE SERIES 15 METRIC SLEEVE SERIES ADAPTER SERIES H23, H39 For tapered bore assembly SERIES H23 METRIC ADAPTER SLEEVE DIMENSIONS SLEEVE NO. H2304 H2305 H2306 H2307 H2308 H2309 H2310 H2311 H2312 H2313 H2314 H2315 H2316 H2317 H2318 H2319 H2320 H2321 H2322 H2324 H2326 H2328 H2330 H2332 H2334 H2336 H2338 H2340 H2344 H2348 H2352 H2356 BORE DIA. d NOM. 0.669 0.787 0.984 1.181 1.378 1.575 1.772 1.968 2.165 2.362 2.362 2.559 2.756 2.953 3.150 3.346 3.543 3.740 3.937 4.331 4.528 4.921 5.315 5.512 5.906 6.299 6.693 7.087 7.874 8.661 9.449 10.236 SHARP CORNER DIA. A MIN. 0.866 1.071 1.280 1.488 1.693 1.898 2.106 2.319 2.524 2.728 2.933 3.146 3.350 3.555 3.768 3.972 4.189 4.402 4.606 5.020 5.441 5.862 6.276 6.693 7.106 7.520 7.933 8.346 9.157 9.980 10.799 11.626 SLEEVE LENGTH L MAX. 1.220 1.378 1.496 1.693 1.811 1.968 2.165 2.323 2.441 2.559 2.677 2.874 3.071 3.228 3.386 3.543 3.819 3.976 4.134 4.409 4.764 5.157 5.472 5.787 6.063 6.339 6.654 6.929 7.323 7.835 8.307 8.819 THREADS THD. LENGTH G MIN. M20 X 1 0.433 M25 X 1.5 0.512 M30 X 1.5 0.512 M35 X 1.5 0.551 M40 X 1.5 0.591 M45 X 1.5 0.630 M50 X 1.5 0.669 M55 X 2 0.709 M60 X 2 0.709 M65 X 2 0.748 M70 X 2 0.787 M75 X 2 0.827 M80 X 2 0.906 M85 X 2 0.984 M90 X 2 0.984 M95 X 2 1.024 M100 X 2 1.063 M105 X 2 1.063 M110 X 2 1.102 M120 X 2 1.142 M130 X 2 1.220 M140 X 2 1.260 M150 X 2 1.339 M160 X 3 1.417 M170 X 3 1.457 M180 X 3 1.496 M190 X 3 1.575 M200 X 3 1.614 TR220 X 4 1.732 TR240 X 4 1.811 TR260 X 4 1.929 TR280 X 4 2.008 METRIC THREADS WIDTH F SLOT WIDTH P DEPTH T MIN. 0.059 0.079 0.079 0.079 0.079 0.079 0.079 0.098 0.098 0.098 0.098 0.118 0.118 0.118 0.118 0.118 0.118 0.118 0.118 0.197 0.197 0.197 0.197 0.236 0.236 0.236 0.236 0.236 0.236 0.236 0.315 0.315 MIN. 0.197 0.236 0.236 0.276 0.276 0.276 0.276 0.354 0.354 0.354 0.354 0.354 0.433 0.433 0.433 0.433 0.512 0.512 0.512 0.591 0.591 0.669 0.669 0.748 0.748 0.827 0.827 0.827 0.984 0.984 1.142 1.142 MIN. 0.512 0.630 0.630 0.669 0.709 0.748 0.787 0.827 0.827 0.866 0.945 0.984 1.063 1.142 1.142 1.181 1.220 1.220 1.260 1.339 1.417 1.457 1.535 1.654 1.693 1.732 1.811 1.850 2.008 2.087 2.205 2.283 WIDTH F SLOT WIDTH P DEPTH T MIN. 0.197 0.197 0.197 0.197 0.236 0.236 0.236 0.236 0.236 0.197 0.315 0.315 0.315 0.315 0.315 0.315 0.394 0.394 0.394 0.394 0.394 0.394 0.394 0.394 MIN. 0.591 0.591 0.669 0.669 0.748 0.748 0.827 0.827 0.827 0.787 0.787 0.787 0.945 0.945 0.945 0.945 1.102 1.102 1.102 1.260 1.260 1.260 1.417 1.417 MIN. 1.339 1.417 1.457 1.535 1.654 1.693 1.732 1.811 1.850 0.827 0.827 0.866 0.866 0.866 0.984 1.024 1.024 1.024 1.063 1.063 1.063 1.102 1.102 1.102 SERIES H39 METRIC ADAPTER SLEEVE DIMENSIONS SLEEVE NO. H3924 H3926 H3928 H3930 H3932 H3934 H3936 H3938 H3940 H3944 H3948 H3952 H3956 H3960 H3964 H3968 H3972 H3976 H3980 H3984 H3988 H3992 H3996 H39/500 BORE DIA. d NOM. 4.331 4.528 4.921 5.315 5.512 5.906 6.299 6.693 7.087 7.874 8.661 9.449 10.236 11.024 11.811 12.598 13.386 14.173 14.960 15.748 16.142 16.929 17.717 18.504 SHARP CORNER DIA. A MIN. 4.850 5.256 5.650 6.071 6.465 6.858 7.276 7.673 8.091 8.878 9.669 10.504 11.295 12.134 12.921 13.709 14.496 15.343 16.130 16.917 17.744 18.531 19.358 20.146 SLEEVE LENGTH L MAX. 2.362 2.559 2.598 2.992 3.071 3.110 3.425 3.504 3.858 3.780 3.976 4.567 4.764 5.515 5.512 5.669 5.669 6.457 6.614 6.614 7.441 7.441 7.874 8.189 METRIC THREADS M120 X 2 M130 X 2 M140 X 2 M150 X 2 M160 X 3 M170 X 3 M180 X 3 M190 X 3 M200 X 3 TR220 X 4 TR240 X 4 TR260 X 4 TR280 X 4 TR300 X 4 TR320 X 5 TR340 X 5 TR360 X 5 TR380 X 5 TR400 X 5 TR420 X 5 TR440 X 5 TR460 X 5 TR480 X 5 TR500 X 5 THREADS THD. LENGTH G MIN. 1.142 1.220 1.260 1.339 1.417 1.457 1.496 1.575 1.614 1.535 1.693 1.732 1.890 2.047 2.087 2.205 2.205 2.362 2.520 2.520 2.874 2.874 2.874 3.189 METRIC SLEEVE SERIES 16 17 SK & ASK SERIES WITHDRAWAL SLEEVE DIMENSIONS Inch design and corresponding Removal nut or locknut WITHDRAWAL SLEEVE DIMENSIONS BEARING WITHDRAWAL SLEEVE SLEEVE SLEEVE SHARP LENGTH SLOT THREADS LOCKNUT LOCKWAS REMOVAL BORE NO. -00 SK-8 SK-9 SK-10 SK-11 SK-12 ASK-13 ASK-14 ASK-15 ASK-16 ASK-17 ASK-18 ASK-19 ASK-20 ASK-22 ASK-24 ASK-26 SK-28 SK-30 SK-32 SK-34 SK-36 SK-38 SK-40 SK-44 SK-48 SK-52 SK-56 SK-60 SK-64 APP. WT. (LB.) -000 SK-108 SK-109 SK-110 SK-111 SK-112 ASK-113 ASK-114 ASK-115 ASK-116 ASK-117 ASK-118 ASK-119 ASK-120 ASK-122 ASK-124 ASK-126 SK-128 SK-130 SK-132 SK-134 SK-136 SK-138 SK-140 SK-144 SK-148 SK-152 SK-156 -00 -000 0.16 0.22 0.25 0.31 0.41 0.50 0.94 1.25 1.25 1.45 1.55 1.80 2.00 2.45 3.15 5.00 5.90 6.80 9.95 11.50 12.50 14.50 16.50 19.50 24.50 30.90 33.10 39.20 46.30 0.25 0.31 0.47 0.56 0.69 0.84 1.55 1.80 2.00 2.25 2.55 2.95 3.40 4.25 5.00 8.00 9.50 11.50 15.30 17.50 20.50 22.00 25.50 29.50 34.00 40.75 48.50 BORE 1.5748 1.7717 1.9685 2.1654 2.3622 2.5591 2.7559 2.9528 3.1496 3.3465 3.5433 3.7402 3.937 4.3307 4.7244 5.1181 5.5118 5.9055 6.2992 6.6929 7.0866 7.4803 7.874 8.6614 9.4488 10.2362 11.0236 11.811 12.5981 DIA. HER CORNER DIA. d A L MAX. REF. MAX. 1.3792 1.576 1.7729 1.9697 2.1669 2.3637 2.3637 2.5605 2.7574 2.9543 3.1511 3.3482 3.545 3.9387 4.3324 4.5293 4.9233 5.317 5.5138 5.9075 6.3012 6.6949 7.0886 7.8762 8.6636 9.451 10.2388 11.0262 11.8136 -00 -000 -00 -000 1.585 1.781 1.978 2.175 2.372 2.569 2.769 2.966 3.163 3.359 3.556 3.753 3.95 4.344 4.737 5.131 5.528 5.922 6.316 6.704 7.103 7.497 7.89 8.681 9.469 10.256 11.05 11.837 12.631 1.585 1.782 1.978 2.175 2.372 2.569 2.769 2.966 3.163 3.359 3.556 3.753 3.95 4.344 4.738 5.131 5.528 5.922 6.319 6.713 7.106 7.503 7.897 8.688 9.475 10.262 11.05 1.181 1.26 1.378 1.457 1.575 1.654 1.732 1.85 1.969 2.047 2.087 2.244 2.323 2.559 2.835 3.071 3.228 3.465 3.78 4.094 4.094 4.409 4.646 5.118 5.669 6.102 6.102 6.693 7.087 1.575 1.732 1.968 2.126 2.244 2.402 2.559 2.717 2.835 2.953 3.15 3.346 3.543 3.858 4.134 4.528 4.921 5.315 5.512 5.748 6.063 6.299 6.693 7.126 7.441 7.874 8.268 NO. PER MAJOR INCH DIA. B G F K1 MAX. NOM. MIN. 18 18 18 18 18 12 12 12 12 12 12 12 12 12 12 12 8 8 8 8 8 8 8 6 6 6 6 6 6 1.767 1.967 2.204 2.407 2.626 2.933 3.137 3.34 3.527 3.73 3.918 4.122 4.325 4.778 5.185 5.622 6.097 6.503 6.925 7.331 7.753 8.191 8.628 9.442 10.192 11.004 11.973 12.942 13.723 THD. LGTH. -00 -000 0.236 0.236 0.276 0.276 0.295 0.295 0.295 0.315 0.354 0.354 0.354 0.399 0.413 0.433 0.472 0.472 0.512 0.551 0.551 0.63 0.63 0.709 0.709 0.709 0.787 0.787 0.787 0.984 0.984 0.276 0.276 0.315 0.354 0.394 0.433 0.472 0.472 0.472 0.512 0.551 0.591 0.591 0.63 0.669 0.748 0.787 0.945 0.945 0.945 1.024 1.024 1.181 1.181 1.181 1.181 1.181 WIDTH 0.052 0.052 0.052 0.052 0.052 0.084 0.084 0.084 0.084 0.084 0.084 0.084 0.115 0.115 0.115 0.115 0.115 0.115 0.178 0.178 0.178 0.178 0.178 0.178 0.178 0.178 0.302 0.302 0.302 NUT N07 N08 N09 N10 N11 N12 N12 N13 N14 AN15 AN16 AN17 AN18 AN20 AN22 AN22 AN24 AN26 AN28 AN30 AN32 AN34 AN36 AN40 N44 N048 N052 N056 N060 W07 W08 W09 W10 W11 W12 W12 W13 W14 W15 W16 W17 W18 W20 W22 W22 W24 W26 W28 W30 W32 W34 W36 W40 W44 P48 P52 P56 P60 N09 N10 RN10 RN11 RN12 AN15 AN16 AN17 AN18 AN19 AN20 AN21 AN22 ARN22 ARN24 ARN26 RN28 RN30 RN32 RN34 RN36 RN38 N44 N048 N052 N056 RN56 RN60 RN64 WITHDRAWAL SLEEVES 18 AH SERIES METRIC WITHDRAWAL SLEEVES Metric Design and corresponding Removal nut or locknut WITHDRAWAL SLEEVE DIMENSIONS BEARING SHAFT AH2 BORE DIA. SLEEVE REMOVAL DIA. NO. NUT 40 35 AH208 KM9 45 40 AH209 KM10 50 45 AH210 KM11 55 50 AH211 KM12 60 55 AH212 KM13 65 60 AH213 KM15 70 65 AH214 KM16 75 70 AH215 KM17 80 75 AH216 KM18 85 80 AH217 KM19 90 85 AH218 KM20 95 90 AH219 KM21 100 95 AH220 KM22 110 105 AH222 KM24 120 115 AH224 KM26 130 125 AH226 KM28 140 135 AH228 KM30 150 145 AH230 KM32 160 150 AH232 KM34 170 160 AH234 KM36 180 170 AH236 KM38 190 180 AH238 HML41T 200 190 AH240 HML43T 220 200 AH244 HML47T 240 220 AH248 HML52T 260 240 AH252 HML56T 280 260 AH256 HML60T 300 280 320 300 340 320 360 340 380 360 400 380 420 400 440 420 460 440 480 460 500 480 AH3 AH23 SLEEVE REMOVAL SLEEVE REMOVAL NO. NUT NO. NUT AH308 KM9 AH2308 KM9 AH309 KM10 AH2309 KM10 AH310 KM11 AH2310 KM11 AH311 KM12 AH2311 KM12 AH312 KM13 AH2312 KM13 AH313 KM15 AH2313 KM15 AH314 KM16 AH2314 KM16 AH315 KM17 AH2315 KM17 AH316 KM18 AH2316 KM18 AH317 KM19 AH2317 KM19 AH318 KM20 AH2318 KM20 AH319 KM21 AH2319 KM21 AH320 KM22 AH2320 KM22 AH322 KM24 AH2322 KM25 AH324 KM26 AH2324 KM27 AH326 KM28 AH2326 KM29 AH328 KM30 AH2328 KM31 AH330 KM33 AH2330 KM33 AH332 KM36 AH232 KM36 AH334 KM38 AH2334 KM39 AH2336 KM40 AH2338 HM42T AH2340 HM44T AH2344 HM48T AH2348 HM52T AH2352 HM58T AH2356 HM62T AH31 SLEEVE REMOVAL NO. NUT AH3120 AH3122 AH3124 AH3126 AH3128 AH3130 AH3132 AH3134 AH3136 AH3138 AH3140 AH3144 AH3148 AH3152 AH3156 AH3160 AH3164 AH3168 AH3172 AH3176 AH3180 AH3184 AH3188 AH3192 AH3196 AH31/500 KM22 KM24 KM26 KM28 KM30 KM33 KM36 KM38 KM40 HM42T HM44T HM48T HM52T HM58T HM62T HM66T HM70T HM74T HM80T HM84T HM88T HM92T HM96T HM102T HM106T HM110T AH32 SLEEVE REMOVAL NO. NUT AH3218 AH3219 AH3220 AH3222 AH3224 AH3226 AH3228 AH3230 AH3232 AH3234 AH3236 AH3238 AH3240 KM20 KM21 KM22 KM25 KM27 KM29 KM31 KM33 KM36 KM38 KM40 HM42T HM44T AH3260 AH3264 AH3268 AH3272 AH3276 AH3280 AH3284 AH3288 AH3292 AH3296 AH32/500 HM66T HM70T HM74T HM80T HM84T HM88T HM92T HM96T HM102T HM106T HM110T WITHDRAWAL SLEEVES 19 AH30 AH22 SLEEVE REMOVAL SLEEVE REMOVAL NO. NUT NO. NUT AH3024 KM26 AH3026 KM28 AH3028 KM30 AH3030 KM32 AH3032 KM34 AH3034 KM36 AH3036 KM38 AH3038 HML41T AH3040 HML43T AH3044 HML47T AH3048 HML52T AH3052 HML56T AH3056 HML60T AH3060 HML64T AH3064 HML69T AH3068 HML73T AH3072 HML77T AH3076 HML82T AH3080 HML86T AH3084 HML90T AH3088 HML94T AH3092 HML98T AH3096 HML104T AH30/500 HML108T AH2236 AH2238 AH2240 AH2244 AH2248 AH2252 AH2256 AH2260 AH2264 KM40 HM42T HM44T HM48T HM52T HM58T HM62T HM66T HM70T AH39 SLEEVE REMOVAL NO. NUT AH3934 AH3936 AH3938 AH3940 AH3944 AH3948 AH3952 AH3956 AH3960 AH3964 AH3968 AH3972 AH3976 AH3980 AH3984 AH3988 AH3992 AH3996 AH39/500 HMLL36 HMLL38 HMLL40 HMLL42T HMLL46T HMLL50T HML55T HML59T HML63T HML67T HML71T HMLL75T HMLL79T HMLL83T HMLL87T HMLL92T HMLL96T HMLL100T HMLL104T 20 21 RN REMOVAL NUT SERIES RN AND ARN SERIES Inch design/Ball, cylindrical, spherical and tapered roller bearings REMOVAL NUT DIMENSIONS LOCKNUT NO. THREADS MAJOR DIA. NO. PER INCH d NOM. RN08 RN09 RN10 RN11 RN12 ARN22 ARN24 ARN26 RN28 RN30 RN32 RN34 RN36 RN38 RN56 RN60 RN64 RN68 RN72 RN76 RN80 RN84 RN88 RN92 RN96 1.767 1.967 2.204 2.407 2.626 4.778 5.185 5.622 6.097 6.503 6.925 7.331 7.753 8.191 11.973 12.942 13.723 14.345 14.957 15.988 17.319 18.107 18.894 19.682 20.867 K1 18 18 18 18 18 12 12 12 8 8 8 8 8 8 6 6 6 5-ACME 5-ACME 5-ACME 5-ACME 5-ACME 5-ACME 5-ACME 4-ACME OUTSIDE DIA. C FACE DIA. E NUT WIDTH D MAX. MAX. 2.827 2.984 3.062 3.281 3.500 6.312 6.938 7.312 7.938 8.312 8.938 9.312 9.875 10.688 15.188 16.397 17.015 17.515 18.515 19.640 21.140 22.390 23.640 25.140 26.390 2.072 2.291 2.562 2.812 3.062 5.375 5.625 6.062 6.563 7.062 7.562 8.062 8.563 9.125 13.562 13.635 15.010 15.760 16.135 17.635 18.010 18.760 19.635 20.510 21.260 Notes: Metric HM-T, HML-T, and HMLL-T Series Removal Nuts are also available REMOVAL NUT SERIES 22 SLOT WIDTH G DEPTH H MAX. MIN. MAX. CHAMFER DEPTH D1 MAX. 0.385 0.448 0.594 0.594 0.656 0.781 0.844 0.906 0.969 1.031 1.031 1.094 1.094 1.156 1.468 1.676 1.760 1.760 1.760 1.760 1.885 2.010 2.135 2.260 2.385 0.490 0.490 0.240 0.240 0.240 0.610 0.610 0.610 0.610 0.735 0.735 0.860 0.860 0.860 1.230 3.510 3.510 3.885 3.885 3.885 3.885 4.010 4.010 4.010 4.010 0.151 0.151 0.135 0.135 0.135 0.260 0.291 0.291 0.291 0.323 0.323 0.385 0.385 0.385 0.510 0.698 0.698 0.760 0.760 0.760 0.760 0.885 0.885 0.885 0.885 0.070 0.070 0.078 0.078 0.078 0.141 0.141 0.141 0.141 0.141 0.141 0.141 0.141 0.141 0.203 0.200 0.200 0.200 0.200 0.200 0.260 0.260 0.260 0.260 0.260 23 N-00 SERIES LOCKNUT DIMENSIONS Inch dimensions for ball, roller, spherical and tapered roller bearings Standard Locknut Series LOCKNUT DIMENSIONS LOCKNUT NO. THREADS MAJOR DIA. NO. PER INCH d N-00 N-01 N-02 N-03 N-04 N-05 N-06 N-07 N-08 N-09 N-10 N-11 N-12 N-13 N-14 AN-15 AN-16 AN-17 AN-18 AN-19 AN-20 AN-21 AN-22 AN-24 AN-26 AN-28 AN-30 AN-32 AN-34 AN-36 AN-38 AN-40 N-44 OUTSIDE FACE NUT SLOT SLOT FACE APP. WT. DIA. DIA. WIDTH WIDTH DEPTH RUNOUT (LB./C) C E D G H Sd MIN. K1 MAX. MAX. MAX. MAX. MAX. MAX. 0.391 0.469 0.586 0.664 0.781 0.969 1.173 1.376 1.563 1.767 1.967 2.175 2.360 2.548 2.751 2.933 3.137 3.340 3.527 3.730 3.918 4.122 4.325 4.716 5.106 5.497 5.888 6.284 6.659 7.066 7.472 7.847 8.628 32 32 32 32 32 32 18 18 18 18 18 18 18 18 18 12 12 12 12 12 12 12 12 12 12 12 12 8 8 8 8 8 8 0.755 0.880 1.005 1.130 1.380 1.568 1.755 2.068 2.255 2.536 2.693 2.974 3.161 3.380 3.630 3.880 4.161 4.411 4.661 4.943 5.193 5.443 5.724 6.130 6.755 7.099 7.693 8.068 8.661 9.068 9.474 9.849 11.005 0.625 0.719 0.813 0.938 1.125 1.281 1.500 1.813 2.000 2.281 2.438 2.656 2.844 3.063 3.313 3.563 3.844 4.031 4.281 4.563 4.813 5.000 5.281 5.688 6.188 6.531 7.063 7.438 8.031 8.375 8.781 9.156 9.843 0.229 0.323 0.323 0.354 0.385 0.416 0.416 0.448 0.448 0.448 0.510 0.510 0.541 0.573 0.573 0.604 0.604 0.635 0.698 0.729 0.760 0.760 0.791 0.823 0.885 0.948 0.979 1.041 1.073 1.104 1.135 1.198 1.260 0.120 0.120 0.120 0.120 0.178 0.178 0.178 0.178 0.240 0.240 0.240 0.240 0.240 0.240 0.240 0.360 0.360 0.360 0.360 0.360 0.360 0.485 0.485 0.485 0.610 0.610 0.610 0.610 0.610 0.735 0.735 0.735 0.980 0.073 0.073 0.104 0.104 0.104 0.104 0.104 0.104 0.104 0.104 0.104 0.135 0.135 0.135 0.135 0.135 0.135 0.166 0.166 0.166 0.166 0.198 0.198 0.198 0.260 0.260 0.291 0.291 0.291 0.323 0.323 0.323 0.510 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.006 0.006 0.006 0.006 0.006 0.006 0.006 0.006 0.006 0.006 NOTES: Available in left hand thread (NL series), in stainless steel (NS series), or plated. AN15-AN40 are available with 11 threads per in (N series). K1 threads—American National Form NS Class 3. N-00 SERIES LOCKNUTS 24 2.0 3.3 3.5 5.3 9.0 11.5 13.0 21.0 22.5 29.0 34.0 42.0 47.0 55.0 63.8 78.8 92.5 104.0 130.0 153.8 178.8 193.8 223.0 255.0 317.0 355.0 475.0 525.0 662.5 665.0 775.0 850.0 1050.0 N-00 SERIES SHAFT DIMENSIONS Inch dimensions for ball, roller, spherical and tapered roller bearings SHAFT DIMENSIONS LOCKNUT BEARING NO. BORE THREADS RELIEF MAJOR PITCH MINOR INCH DIA. DIA. DIA. L A W H S M MAX. K1 MAX. MAX. MAX. MAX. MAX. MAX. MIN. MIN. MIN. 0.312 0.406 0.500 0.562 0.719 0.875 1.062 1.250 1.469 1.688 1.875 2.062 2.250 2.438 2.625 2.781 3.000 3.188 3.375 3.562 3.781 3.938 4.188 4.562 4.938 5.312 5.719 6.125 6.500 6.906 7.312 7.688 8.312 32 32 32 32 32 32 18 18 18 18 18 18 18 18 18 12 12 12 12 12 12 12 12 12 12 12 12 8 8 8 8 8 8 0.391 0.469 0.586 0.664 0.781 0.969 1.173 1.376 1.563 1.767 1.967 2.157 2.360 2.548 2.751 2.933 3.137 3.340 3.527 3.730 3.918 4.122 4.325 4.716 5.106 5.497 5.888 6.284 6.659 7.066 7.472 7.847 8.628 0.371 0.449 0.566 0.644 0.761 0.949 1.137 1.340 1.527 1.731 1.931 2.121 2.324 2.512 2.715 2.879 3.083 3.286 3.473 3.676 3.864 4.068 4.271 4.662 5.052 5.443 5.834 6.203 6.578 6.985 7.391 7.766 8.547 0.353 0.431 0.548 0.626 0.743 0.931 1.105 1.308 1.495 1.699 1.899 2.089 2.292 2.480 2.683 2.831 3.035 3.238 3.425 3.628 3.816 4.020 4.223 4.614 5.004 5.395 5.786 6.131 6.506 6.913 7.319 7.694 8.475 0.297 0.391 0.391 0.422 0.453 0.484 0.484 0.516 0.547 0.547 0.609 0.609 0.641 0.672 0.672 0.703 0.703 0.734 0.828 0.859 0.891 0.891 0.922 0.953 1.016 1.078 1.141 1.203 1.234 1.266 1.297 1.359 1.391 0.342 0.420 0.537 0.615 0.732 0.920 1.094 1.297 1.484 1.688 1.888 2.078 2.281 2.469 2.672 2.810 3.014 3.217 3.404 3.607 3.795 3.999 4.202 4.593 4.983 5.374 5.765 6.109 6.484 6.891 7.297 7.672 8.453 0.078 0.078 0.078 0.078 0.078 0.078 0.109 0.109 0.109 0.141 0.141 0.141 0.141 0.141 0.141 0.172 0.172 0.172 0.172 0.172 0.172 0.172 0.172 0.172 0.172 0.172 0.172 0.266 0.266 0.266 0.266 0.266 0.266 0.062 0.062 0.078 0.078 0.078 0.094 0.094 0.094 0.094 0.094 0.094 0.125 0.125 0.125 0.125 0.125 0.125 0.125 0.156 0.156 0.156 0.156 0.188 0.188 0.188 0.188 0.219 0.234 0.234 0.234 0.234 0.234 0.375 0.125 0.125 0.125 0.125 0.188 0.188 0.188 0.188 0.312 0.312 0.312 0.312 0.312 0.312 0.312 0.312 0.375 0.375 0.375 0.375 0.375 0.375 0.375 0.375 0.500 0.625 0.625 0.625 0.750 0.750 0.750 0.875 1.062 0.094 0.094 0.094 0.094 0.094 0.125 0.125 0.125 0.125 0.156 0.156 0.156 0.156 0.156 0.250 0.250 0.250 0.250 0.250 0.250 0.312 0.312 0.312 0.312 0.312 0.312 0.375 0.375 0.375 0.375 0.375 0.375 0.188 V2 N-00 N-01 N-02 N-03 N-04 N-05 N-06 N-07 N-08 N-09 N-10 N-11 N-12 N-13 N-14 AN-15 AN-16 AN-17 AN-18 AN-19 AN-20 AN-21 AN-22 AN-24 AN-26 AN-28 AN-30 AN-32 AN-34 AN-36 AN-38 AN-40 N-44 0.394 0.472 0.591 0.669 0.787 0.984 1.181 1.378 1.575 1.772 1.969 2.165 2.362 2.559 2.756 2.953 3.150 3.347 3.543 3.740 3.937 4.134 4.331 4.724 5.118 5.512 5.906 6.299 6.693 7.087 7.480 7.874 8.661 LENGTH DIA. KEYWAY NO. PER WIDTH DEPTH WIDTH NOTES: K1 threads—American National Form NS Class 3. N-00 SERIES SHAFTS 25 N-000 SERIES LOCKNUT DIMENSIONS Inch dimensions for ball, roller, spherical and tapered roller bearings Larger Bore Series LOCKNUT DIMENSIONS LOCKNUT NO. THREADS MAJOR DIA. NO. PER INCH d N-022 N-024 N-026 N-028 N-030 N-032 N-034 N-036 N-038 N-040 N-044 N-048 N-052 N-056 N-060 N-064 N-068 N-072 N-076 N-080 N-084 N-088 N-092 N-096 N-500 N-530 N-560 N-600 N-630 N-670 N-710 N-750 N-800 N-850 N-900 N-950 MIN. K1 4.325 4.716 5.106 5.497 5.888 6.284 6.659 7.066 7.472 7.847 8.628 9.442 10.192 11.004 11.785 12.562 13.339 14.170 14.957 15.745 16.532 17.319 18.107 18.894 19.682 20.867 22.048 23.623 24.804 26.379 27.961 29.536 31.504 33.473 35.441 37.410 12 12 12 12 12 8 8 8 8 8 8 6 6 6 6 6 OUTSIDE DIA. FACE DIA. NUT WIDTH SLOT WIDTH SLOT DEPTH FACE RUNOUT COUNTERBORE DIA. DEPTH TAPPED HOLES FOR MOUNTING B.C. DIA TAP SIZE DEPTH C E D G H Sd U L1 Y M1 MAX. MAX. MAX. MAX. MAX. MAX. MIN. MIN. MIN. 5 5 5 5 5 5 5 5 5 4 4 4 4 4 3 3 3 3 3 3 5.318 5.693 6.130 6.505 7.130 7.505 7.880 8.255 8.693 9.443 10.255 11.443 12.193 13.005 14.193 15.005 15.755 16.505 17.755 18.505 19.318 20.505 21.255 22.068 22.818 24.818 25.568 27.568 28.755 30.693 32.693 34.255 36.255 38.568 40.568 43.005 4.901 5.313 5.703 6.109 6.688 7.094 7.484 7.875 8.266 8.750 9.531 10.625 11.406 12.219 13.219 14.031 14.813 15.500 16.625 17.438 18.188 19.250 20.688 20.750 21.688 23.250 24.000 26.000 27.125 29.125 30.688 32.313 34.250 36.375 38.375 40.500 0.791 0.823 0.885 0.948 0.979 1.041 1.073 1.104 1.135 1.198 1.260 1.354 1.416 1.510 1.573 1.666 1.791 1.791 1.916 2.073 2.073 2.385 2.385 2.385 2.703 2.703 2.953 2.953 2.953 3.140 3.578 3.578 3.578 3.578 3.953 3.953 0.485 0.485 0.485 0.485 0.610 0.610 0.610 0.610 0.610 0.735 0.860 0.860 0.860 0.980 0.980 0.980 0.980 1.230 1.230 1.230 1.355 1.355 1.355 1.480 1.480 1.605 1.605 1.605 1.855 1.855 1.980 2.230 2.230 2.480 2.480 2.480 0.198 0.198 0.198 0.198 0.229 0.229 0.229 0.229 0.229 0.323 0.385 0.385 0.385 0.385 0.510 0.510 0.510 0.510 0.604 0.604 0.604 0.604 0.604 0.604 0.604 0.823 0.823 0.823 0.823 0.823 1.010 1.010 1.010 1.010 1.010 1.010 0.006 0.006 0.006 0.006 0.006 0.006 0.006 0.006 0.006 0.006 0.006 0.008 0.008 0.008 0.008 0.008 0.008 0.008 0.008 0.008 0.008 0.008 0.008 0.010 0.010 0.010 0.010 0.010 0.010 0.010 0.012 0.012 0.012 0.012 0.012 0.012 0.375 0.375 0.375 0.375 0.375 0.375 0.375 0.375 0.375 0.500 0.500 0.500 0.500 0.500 0.688 0.688 0.688 0.688 0.688 0.688 10.423 11.298 12.110 13.110 13.860 14.735 15.485 16.485 17.235 18.110 19.110 19.985 20.673 21.610 23.360 24.110 25.923 27.235 28.985 30.610 32.235 34.610 36.485 38.610 40.610 NOTES: K1 threads—American National Form NS Class 3. M1 threads—ACME Class 3G General Purpose. N-000 SERIES LOCKNUTS 26 13.355 14.186 14.973 15.761 16.548 17.335 18.123 18.910 19.698 20.887 22.068 23.643 24.824 26.399 27.988 29.563 31.531 33.500 35.468 37.437 T1 S1 MIN. 5/16----18 5/16----18 5/16----18 3/8----16 3/8----16 3/8----16 3/8----16 1/2----13 1/2----13 1/2----13 5/8----11 5/8----11 5/8----11 5/8----11 5/8----11 5/8----11 5/8----11 5/8----11 5/8----11 5/8----11 5/8----11 5/8----11 3/4----10 3/4----10 3/4----10 0.625 0.625 0.625 0.750 0.750 0.750 0.750 0.875 0.875 0.875 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.500 1.500 1.500 N-000 SERIES SHAFT DIMENSIONS Inch dimensions for ball, roller, spherical and tapered roller bearings SHAFT DIMENSIONS LOCKNUT BEARING NO. BORE THREADS MAJOR PITCH MINOR INCH DIA. DIA. DIA. L A W H S M V M1 MAX. MAX. MAX. MAX. MAX. MAX. MIN. MIN. MIN. MIN. 4.271 4.662 5.052 5.443 5.834 6.203 6.578 6.985 7.391 7.766 8.547 9.334 10.084 10.896 11.677 12.454 13.203 14.034 14.821 15.609 16.396 17.183 17.971 18.758 19.546 20.702 21.883 23.458 24.639 26.214 27.747 29.322 31.290 33.259 35.227 37.196 4.223 4.614 5.004 5.395 5.786 6.131 6.506 6.913 7.319 7.694 8.475 9.237 9.987 10.799 11.580 12.357 13.083 13.914 14.701 15.489 16.276 17.063 17.851 18.638 19.426 20.557 21.738 23.313 24.494 26.069 27.560 29.135 31.103 33.072 35.040 37.009 0.922 0.953 1.016 1.078 1.141 1.203 1.234 1.266 1.297 1.359 1.391 1.734 1.797 1.891 1.953 2.047 2.172 2.172 2.297 2.453 2.453 2.766 2.766 2.766 3.141 3.141 3.391 3.391 3.391 3.578 4.109 4.141 4.141 4.141 4.516 4.516 4.202 4.593 4.983 5.374 5.765 6.109 6.484 6.891 7.297 7.672 8.453 9.201 9.951 10.763 11.544 12.321 13.046 13.877 14.664 15.452 16.239 17.026 17.814 18.601 19.389 20.504 21.685 23.260 24.441 26.016 27.507 29.082 31.050 33.019 34.987 36.956 0.172 0.172 0.172 0.172 0.172 0.266 0.266 0.266 0.266 0.266 0.266 0.266 0.266 0.266 0.266 0.266 0.266 0.266 0.266 0.266 0.266 0.266 0.266 0.266 0.266 0.266 0.266 0.266 0.266 0.266 0.391 0.391 0.391 0.391 0.391 0.391 0.188 0.188 0.188 0.188 0.219 0.234 0.234 0.234 0.234 0.234 0.375 0.438 0.438 0.438 0.438 0.438 0.438 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.625 0.625 0.625 0.625 0.625 0.750 0.375 0.375 0.500 0.625 0.625 0.625 0.750 0.750 0.750 0.875 1.062 1.125 1.188 1.250 1.375 1.438 1.500 1.500 1.500 1.625 1.625 1.812 1.812 1.812 1.812 1.812 1.812 1.812 2.000 2.000 2.000 2.000 2.000 2.000 2.000 2.000 0.312 0.312 0.312 0.312 0.375 0.375 0.375 0.375 0.375 0.375 0.188 5 5 5 5 5 5 5 5 5 4 4 4 4 4 3 3 3 3 3 3 4.325 4.716 5.106 5.497 5.888 6.284 6.659 7.066 7.472 7.847 8.628 9.442 10.192 11.004 11.785 12.562 13.303 14.134 14.921 15.709 16.496 17.283 18.071 18.858 19.646 20.827 22.008 23.583 24.764 26.339 27.914 29.489 31.457 33.426 35.394 37.363 V2 N-022 N-024 N-026 N-028 N-030 N-032 N-034 N-036 N-038 N-040 N-044 N-048 N-052 N-056 N-060 N-064 N-068 N-072 N-076 N-080 N-084 N-088 N-092 N-096 N-500 N-530 N-560 N-600 N-630 N-670 N-710 N-750 N-800 N-850 N-900 N-950 4.331 4.724 5.118 5.512 5.906 6.299 6.693 7.087 7.480 7.874 8.661 9.449 10.236 11.024 11.811 12.598 13.386 14.173 14.961 15.748 16.535 17.323 18.110 18.898 19.685 20.866 22.047 23.622 24.803 26.378 27.953 29.528 31.496 33.465 35.433 37.402 KEYWAY RELIEF NO. PER MAX. K1 4.188 4.562 4.938 5.312 5.719 6.125 6.500 6.906 7.312 7.688 8.312 9.188 9.938 10.750 11.500 12.312 13.062 13.812 14.625 15.375 16.188 17.000 17.750 18.500 19.250 20.250 21.500 23.000 24.250 25.750 27.250 28.750 30.750 32.750 34.750 36.750 12 12 12 12 12 8 8 8 8 8 8 6 6 6 6 6 LENGTH DIA. WIDTH DEPTH WIDTH 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500 NOTES: K1 threads—American National Form NS Class 3. M1 threads—ACME Class 3G General Purpose. N-000 SERIES SHAFTS 27 PRN/PRL-00 SERIES LOCKNUT DIMENSIONS Inch dimensions for ball, roller, spherical and tapered roller bearings Tighter Face Runout Tolerance LOCKNUT DIMENSIONS LOCKNUT NO. PRN-00 PRN-01 PRN-02 PRN-03 PRN-04 PRN-05 PRN-06 PRN-07 PRN-08 PRN-09 PRN-10 PRN-11 PRN-12 PRN-13 PRN-14 PRN-15 PRN-16 PRN-17 PRN-18 PRN-19 PRN-20 PRN-21 PRN-22 PRN-24 PRN-26 PRN-28 PRN-30 PRN-32 PRN-34 PRN-36 PRN-38 PRN-40 THREADS OUTSIDE FACE NUT SLOT SLOT FACE APP. WT. NO. PER INCH DIA. DIA. WIDTH WIDTH DEPTH RUNOUT (LB./C) d MIN. K1 C MAX. E MAX. D MAX. G MAX. H MAX. Sd MAX. 0.391 0.469 0.586 0.664 0.781 0.969 1.173 1.376 1.563 1.767 1.967 2.157 2.360 2.548 2.751 2.933 3.137 3.340 3.527 3.730 3.918 4.122 4.325 4.716 5.106 5.497 5.888 6.284 6.659 7.066 7.472 7.847 32 32 32 32 32 32 18 18 18 18 18 18 18 18 18 12 12 12 12 12 12 12 12 12 12 12 12 8 8 8 8 8 0.755 0.880 1.005 1.130 1.380 1.568 1.755 2.068 2.255 2.536 2.693 2.974 3.161 3.380 3.630 3.880 4.161 4.411 4.661 4.943 5.193 5.443 5.724 6.130 6.755 7.099 7.693 8.068 8.661 9.068 9.474 9.849 0.625 0.719 0.813 0.938 1.125 1.281 1.500 1.813 2.000 2.281 2.438 2.656 2.844 3.063 3.313 3.563 3.844 4.031 4.281 4.563 4.813 5.000 5.281 5.688 6.188 6.531 7.063 7.438 8.031 8.375 8.781 9.156 0.229 0.323 0.323 0.354 0.385 0.416 0.416 0.448 0.448 0.448 0.510 0.510 0.541 0.573 0.573 0.604 0.604 0.635 0.698 0.729 0.760 0.760 0.791 0.823 0.885 0.948 0.979 1.041 1.073 1.104 1.135 1.198 0.120 0.120 0.120 0.120 0.178 0.178 0.178 0.178 0.240 0.240 0.240 0.240 0.240 0.240 0.240 0.360 0.360 0.360 0.360 0.360 0.360 0.485 0.485 0.485 0.610 0.610 0.610 0.610 0.610 0.735 0.735 0.735 0.073 0.073 0.104 0.104 0.104 0.104 0.104 0.104 0.104 0.104 0.104 0.135 0.135 0.135 0.135 0.135 0.135 0.166 0.166 0.166 0.166 0.198 0.198 0.198 0.260 0.260 0.291 0.291 0.291 0.323 0.323 0.323 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 MAJOR DIA. NOTES: This series has a tighter face runout tolerance than the standard N/AN series. Also available in left hand thread , specify “PRL” series. K1 Threads—American National Form NS Class 3. PRN/PRL-00 SERIES LOCKNUTS 28 2.0 3.3 3.5 5.3 9.0 11.5 13.0 21.0 22.5 29.0 34.0 42.0 47.0 55.0 63.8 78.8 92.5 104.0 130.0 153.8 178.8 193.8 223.0 255.0 317.0 355.0 475.0 525.0 662.5 665.0 775.0 850.0 PRT-00 SERIES LOCKNUT DIMENSIONS Inch dimensions for ball, roller, spherical and tapered roller bearings Narrow Versions of N Series LOCKNUT DIMENSIONS LOCKNUT NO. THREADS MAJOR DIA. NO. PER INCH d PRT-00 PRT-01 PRT-02 PRT-03 PRT-04 PRT-05 PRT-06 PRT-07 PRT-08 PRT-09 PRT-10 PRT-11 PRT-12 PRT-13 PRT-14 PRT-15 PRT-16 PRT-17 PRT-18 OUTSIDE FACE NUT SLOT SLOT FACE APP. WT. DIA. DIA. WIDTH WIDTH DEPTH RUNOUT (LB./C) C E D G H Sd MIN. K1 MAX. MAX. MAX. MAX. MAX. MAX. 0.391 0.469 0.586 0.664 0.781 0.969 1.173 1.376 1.563 1.767 1.967 2.157 2.360 2.548 2.751 2.933 3.137 3.340 3.527 32 32 32 32 32 32 18 18 18 18 18 18 18 18 18 12 12 12 12 0.724 0.818 0.943 1.067 1.193 1.380 1.693 1.911 2.099 2.317 2.505 2.755 2.942 3.130 3.349 3.693 3.911 4.130 4.317 0.531 0.625 0.750 0.875 1.000 1.188 1.438 1.656 1.844 2.062 2.250 2.500 2.688 2.875 3.094 3.375 3.594 3.812 4.000 0.198 0.198 0.229 0.229 0.260 0.260 0.260 0.291 0.291 0.291 0.322 0.322 0.322 0.354 0.354 0.354 0.385 0.385 0.385 0.120 0.120 0.120 0.120 0.178 0.178 0.178 0.178 0.240 0.240 0.240 0.240 0.240 0.240 0.240 0.360 0.360 0.360 0.360 0.065 0.065 0.065 0.065 0.080 0.065 0.096 0.096 0.096 0.096 0.096 0.096 0.096 0.096 0.096 0.128 0.128 0.128 0.128 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 0.001 1.7 2.1 3.0 3.8 5.0 6.0 9.4 12.4 13.9 15.9 18.9 22.8 24.1 28.4 31.3 43.7 51.5 55.6 58.4 NOTES: This series is designed to accommodate limited space applications where high precision is required. PRT-00 SERIES LOCKNUTS 29 SN-00 SERIES LOCKNUT DIMENSIONS Inch dimensions for ball, roller, spherical and tapered roller bearings Self Locking LOCKNUT DIMENSIONS LOCKNUT NO. THREADS MAJOR DIA. NO. PER INCH d SN-00 SN-01 SN-02 SN-03 SN-04 SN-05 SN-06 SN-07 SN-08 SN-09 SN-10 SN-11 SN-12 SN-13 SN-14 SN-15 SN-16 SN-17 SN-18 SN-19 SN-20 SN-21 SN-22 SN-24 SN-26 SN-28 SN-30 SN-32 SN-34 SN-36 SN-38 SN-40 OUTSIDE FACE NUT SLOT SLOT FACE APP. WT. DIA. DIA. WIDTH WIDTH DEPTH RUNOUT (LB./C) C E D G H Sd MIN. K1 MAX. MAX. MAX. MAX. MAX. MAX. 0.391 0.469 0.586 0.664 0.781 0.969 1.173 1.376 1.563 1.767 1.967 2.157 2.360 2.548 2.751 2.933 3.137 3.340 3.527 3.730 3.918 4.122 4.325 4.716 5.106 5.497 5.888 6.284 6.659 7.066 7.472 7.847 32 32 32 32 32 32 18 18 18 18 18 18 18 18 18 12 12 12 12 12 12 12 12 12 12 12 12 8 8 8 8 8 0.755 0.880 1.005 1.130 1.380 1.568 1.755 2.068 2.255 2.536 2.693 2.974 3.161 3.380 3.630 3.880 4.161 4.411 4.661 4.943 5.193 5.443 5.724 6.130 6.755 7.099 7.693 8.068 8.661 9.068 9.474 9.849 0.625 0.719 0.813 0.938 1.125 1.281 1.500 1.813 2.000 2.281 2.438 2.656 2.844 3.063 3.313 3.563 3.844 4.031 4.281 4.563 4.813 5.000 5.281 5.688 6.188 6.531 7.063 7.438 8.031 8.375 8.781 9.156 0.276 0.369 0.369 0.401 0.432 0.463 0.463 0.510 0.510 0.510 0.573 0.573 0.604 0.635 0.635 0.604 0.604 0.635 0.698 0.729 0.760 0.760 0.791 0.823 0.885 0.948 0.979 1.041 1.073 1.104 1.135 1.198 0.120 0.120 0.120 0.120 0.178 0.178 0.178 0.178 0.240 0.240 0.240 0.240 0.240 0.240 0.240 0.360 0.360 0.360 0.360 0.360 0.360 0.485 0.485 0.485 0.610 0.610 0.610 0.610 0.610 0.735 0.735 0.735 0.073 0.073 0.104 0.104 0.104 0.104 0.104 0.104 0.104 0.104 0.104 0.135 0.135 0.135 0.135 0.135 0.135 0.166 0.166 0.166 0.166 0.198 0.198 0.198 0.260 0.260 0.291 0.291 0.291 0.323 0.323 0.323 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.006 0.006 0.006 0.006 0.006 0.006 0.006 0.006 0.006 2.0 3.3 3.5 5.3 9.0 11.5 13.0 21.0 22.5 29.0 34.0 42.0 47.0 55.0 63.8 78.8 92.5 104.0 130.0 153.8 178.8 193.8 223.0 255.0 317.0 355.0 475.0 525.0 662.5 665.0 775.0 850.0 NOTES: This series is designed with a “Self-Locking” nylon insert which eliminates the need for a lockwasher and shaft keyway. Also available in left hand thread (SNL), metric (SM) and stainless steel (SNS). K1 Threads—American National Form NS Class 3. SN/SNL-00 SERIES LOCKNUTS 30 SNH-00 SERIES LOCKNUT DIMENSIONS Inch dimensions for ball, roller, spherical and tapered roller bearings Self-Locking and High Temperature LOCKNUT DIMENSIONS LOCKNUT NO. THREADS OUTSIDE FACE NUT SLOT SLOT NO. PER INCH DIA. DIA. WIDTH WIDTH DEPTH C E D G H MIN. K1 MAX. MAX. MAX. MAX. MAX. 0.391 0.469 0.586 0.664 0.781 0.969 1.173 1.376 1.563 1.767 1.967 2.157 2.360 2.548 2.751 2.933 3.137 3.340 3.527 3.730 3.918 4.122 4.325 32 32 32 32 32 32 18 18 18 18 18 18 18 18 18 12 12 12 12 12 12 12 12 0.755 0.880 1.005 1.130 1.380 1.568 1.755 2.068 2.255 2.536 2.693 2.974 3.161 3.380 3.630 3.880 4.161 4.411 4.661 4.943 5.193 5.443 5.724 0.625 0.719 0.813 0.938 1.125 1.281 1.500 1.813 2.000 2.281 2.438 2.656 2.844 3.063 3.313 3.563 3.844 4.031 4.281 4.563 4.813 5.000 5.281 0.229 0.323 0.323 0.354 0.385 0.416 0.416 0.448 0.448 0.448 0.510 0.510 0.541 0.573 0.573 0.604 0.604 0.635 0.698 0.729 0.760 0.760 0.791 0.120 0.120 0.120 0.120 0.178 0.178 0.178 0.178 0.240 0.240 0.240 0.240 0.240 0.240 0.240 0.360 0.360 0.360 0.360 0.360 0.360 0.485 0.485 0.073 0.073 0.104 0.104 0.104 0.104 0.104 0.104 0.104 0.104 0.104 0.135 0.135 0.135 0.135 0.135 0.135 0.166 0.166 0.166 0.166 0.198 0.198 MAJOR DIA. d SNH-00 SNH-01 SNH-02 SNH-03 SNH-04 SNH-05 SNH-06 SNH-07 SNH-08 SNH-09 SNH-10 SNH-11 SNH-12 SNH-13 SNH-14 SNH-15 SNH-16 SNH-17 SNH-18 SNH-19 SNH-20 SNH-21 SNH-22 NOTES: This series is designed with a “Self-Locking” nylon insert which can accommodate temperatures up to 350°F. K1 Threads—American National Form Class 3. SNH-00 SERIES LOCKNUTS 31 NHE-00 SERIES LOCKNUT DIMENSIONS Inch dimensions for ball, roller, spherical and tapered roller bearings Heavy Load LOCKNUT DIMENSIONS LOCKNUT NO. THREADS MAJOR DIA. NO. PER INCH d NHE-08 NHE-09 NHE-10 NHE-11 NHE-12 NHE-13 NHE-14 NHE-15 NHE-16 NHE-17 NHE-18 NHE-19 NHE-20 NHE-21 NHE-22 NHE-24 NHE-26 NHE-28 NHE-30 NHE-32 NHE-34 NHE-36 NHE-38 NHE-40 OUTSIDE FACE NUT SLOT SLOT FACE APP. WT. DIA. DIA. WIDTH WIDTH DEPTH RUNOUT (LB./C) C E D G H Sd MIN. K1 MAX. MAX. MAX. MAX. MAX. MAX. 1.563 1.767 1.967 2.157 2.360 2.548 2.751 2.933 3.137 3.340 3.527 3.730 3.918 4.122 4.325 4.716 5.106 5.497 5.888 6.284 6.659 7.066 7.472 7.847 18 18 18 18 18 18 18 12 12 12 12 12 12 12 12 12 12 12 12 8 8 8 8 8 2.255 2.536 2.693 2.974 3.161 3.380 3.630 3.880 4.161 4.411 4.661 4.943 5.193 5.443 5.724 6.130 6.755 7.099 7.693 8.068 8.661 9.068 9.474 9.849 2.000 2.281 2.438 2.656 2.844 3.063 3.313 3.563 3.844 4.031 4.281 4.563 4.813 5.000 5.281 5.688 6.188 6.531 7.063 7.438 8.031 8.375 8.781 9.156 0.572 0.572 0.635 0.635 0.666 0.729 0.729 0.760 0.760 0.791 0.885 0.916 0.948 0.948 0.979 1.041 1.104 1.198 1.260 1.291 1.354 1.416 1.416 1.510 0.240 0.240 0.240 0.240 0.240 0.240 0.240 0.360 0.360 0.360 0.360 0.360 0.360 0.485 0.485 0.485 0.610 0.610 0.610 0.610 0.610 0.735 0.735 0.735 0.104 0.104 0.104 0.135 0.135 0.135 0.135 0.135 0.135 0.166 0.166 0.166 0.166 0.198 0.198 0.198 0.260 0.260 0.291 0.291 0.291 0.323 0.323 0.323 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 NOTES: This series is designed with a wider nut width (D) to accommodate heavier loads. K1 Threads—American National Form NS Class 3. NHE-00 SERIES LOCKNUTS 32 35.7 44.4 50.7 62.4 69.3 84.4 95.7 117.9 135.9 156.5 195.2 227.9 259.7 282.0 323.0 374.7 502.8 564.0 716.7 783.7 977.6 1077.2 1131.8 1260.8 NIN-00 SERIES LOCKNUT DIMENSIONS Inch dimensions for ball, roller, spherical and tapered roller bearings 16 Threads per Inch LOCKNUT DIMENSIONS LOCKNUT NO. THREADS MAJOR DIA. NO. PER INCH d NIN-01 NIN-02 NIN-03 NIN-04 NIN-05 NIN-06 NIN-07 NIN-08 NIN-09 NIN-10 NIN-11 NIN-12 NIN-13 NIN-14 OUTSIDE FACE NUT SLOT SLOT FACE APP. WT. DIA. DIA. WIDTH WIDTH DEPTH RUNOUT (LB./C) C E D G H Sd MIN. K1 MAX. MAX. MAX. MAX. MAX. MAX. 0.750 0.875 1.000 1.125 1.250 1.375 1.500 1.625 1.750 1.875 2.000 2.250 2.500 2.750 16 16 16 16 16 16 16 16 16 16 16 16 16 16 1.505 1.630 1.755 1.880 2.005 2.255 2.255 2.505 2.630 2.755 3.005 3.255 3.505 3.755 1.188 1.313 1.438 1.563 1.688 1.938 1.938 2.188 2.313 2.438 2.688 2.875 3.125 3.375 0.385 0.385 0.385 0.385 0.510 0.510 0.510 0.510 0.510 0.510 0.510 0.635 0.635 0.635 0.240 0.240 0.240 0.240 0.240 0.240 0.240 0.302 0.302 0.302 0.302 0.302 0.302 0.302 0.138 0.138 0.138 0.138 0.138 0.138 0.138 0.138 0.138 0.138 0.138 0.169 0.169 0.169 0.002 0.002 0.002 0.002 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 14.5 16.1 17.7 19.3 27.7 36.0 32.0 41.0 43.4 45.9 56.7 77.7 84.8 91.8 NOTES: K1 Threads—American National Form Class 3. NIN-00 SERIES LOCKNUTS 33 NTH-00 SERIES LOCKNUT DIMENSIONS Inch dimensions for ball, roller, spherical and tapered roller bearings Thinner Design LOCKNUT DIMENSIONS LOCKNUT NO. THREADS MAJOR DIA. NO. PER INCH d NTH-00 NTH-01 NTH-02 NTH-03 NTH-04 NTH-05 NTH-06 NTH-07 NTH-08 NTH-09 NTH-10 NTH-11 NTH-12 NTH-13 NTH-14 NTH-15 NTH-16 NTH-17 NTH-18 OUTSIDE FACE NUT SLOT SLOT FACE APP. WT. DIA. DIA. WIDTH WIDTH DEPTH RUNOUT (LB./C) C E D G H Sd MIN. K1 MAX. MAX. MAX. MAX. MAX. MAX. 0.391 0.469 0.586 0.664 0.781 0.969 1.173 1.376 1.563 1.767 1.967 2.157 2.360 2.548 2.751 2.933 3.137 3.340 3.527 32 32 32 32 32 32 18 18 18 18 18 18 18 18 18 12 12 12 12 0.724 0.818 0.943 1.068 1.193 1.380 1.693 1.911 2.099 2.318 2.505 2.755 2.943 3.130 3.349 3.693 3.911 4.130 4.318 0.531 0.625 0.750 0.875 1.000 1.188 1.438 1.656 1.844 2.062 2.250 2.500 2.688 2.875 3.094 3.375 3.594 3.812 4.000 0.198 0.198 0.229 0.229 0.260 0.260 0.260 0.291 0.291 0.291 0.322 0.322 0.322 0.354 0.354 0.354 0.385 0.385 0.385 0.120 0.120 0.120 0.120 0.178 0.178 0.178 0.178 0.240 0.240 0.240 0.240 0.240 0.240 0.240 0.360 0.360 0.360 0.360 0.065 0.065 0.065 0.065 0.080 0.065 0.096 0.096 0.096 0.096 0.096 0.096 0.096 0.096 0.096 0.128 0.128 0.128 0.128 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 NOTES: This series is designed with a thinner width (D) to accommodate narrow spaces. K1 Threads—American National Form NS Class 3. NTH-00 SERIES LOCKNUTS 34 1.7 2.1 3.0 3.8 5.0 6.0 9.4 12.4 13.9 15.9 18.9 22.8 24.1 28.4 31.3 43.7 51.5 55.6 58.4 KM-00 SERIES LOCKNUT DIMENSIONS Metric dimensions for ball, roller, spherical and tapered roller bearings Metric Design LOCKNUT DIMENSIONS LOCKNUT NO. KM 0 KM 1 KM 2 KM 3 KM 4 KM 4.4 KM 5 KM 5.6 KM 6 KM 6.4 KM 7 KM 8 KM 9 KM 10 KM 11 KM 12 KM 13 KM 14 KM 15 KM 16 KM 17 KM 18 KM 19 KM 20 KM 21 KM 22 KM 23 KM 24 KM 25 KM 26 KM 27 KM 28 KM 29 KM 30 KM 31 KM 32 KM 33 KM 34 KM 36 KM 38 KM 40 KM 44 KM 48 KM 52 KM 56 METRIC THREADS M 10x0.75 M 12x1 M 15x1 M 17x1 M 20x1 M 22x1 M 25x1.5 M 28x1.5 M 30x1.5 M 32x1.5 M 35x1.5 M 40x1.5 M 45x1.5 M 50x1.5 M 55x2 M 60x2 M 65x2 M 70x2 M 75x2 M 80x2 M 85x2 M 90x2 M 95x2 M100x2 M105x2 M110x2 M115x2 M120x2 M125x2 M130x2 M135x2 M140x2 M145x2 M150x2 M155x3 M160x3 M165x3 M170x3 M180x3 M190x3 M200x3 Tr220x3 Tr240x4 Tr260x4 Tr280x4 OUTSIDE DIA. FACE DIA. NUT WIDTH SLOT WIDTH SLOT DEPTH FACE RUNOUT C MAX. E MAX. D MAX. G MAX. H MAX. Sd MAX. 0.709 0.866 0.984 1.102 1.260 1.339 1.496 1.654 1.772 1.890 2.047 2.283 2.559 2.756 2.953 3.150 3.346 3.622 3.858 4.134 4.331 4.724 4.921 5.118 5.512 5.709 5.906 6.102 6.299 6.496 6.890 7.087 7.480 7.677 7.874 8.268 8.268 8.661 9.055 9.449 9.843 11.024 11.811 12.992 13.780 0.531 0.669 0.827 0.945 1.024 1.102 1.206 1.417 1.496 1.575 1.732 1.969 2.205 2.402 2.638 2.874 3.110 3.346 3.543 3.740 4.016 4.252 4.449 4.724 4.961 5.236 5.394 5.433 5.827 5.866 6.299 6.299 6.732 6.732 7.165 7.165 7.598 7.598 7.992 8.425 8.898 9.843 10.630 11.811 12.598 0.157 0.157 0.197 0.197 0.236 0.236 0.276 0.276 0.276 0.315 0.315 0.354 0.394 0.433 0.433 0.433 0.472 0.472 0.512 0.591 0.630 0.630 0.669 0.709 0.709 0.748 0.748 0.787 0.827 0.827 0.866 0.866 0.945 0.945 0.984 0.984 1.024 1.024 1.063 1.102 1.142 1.260 1.339 1.417 1.496 0.118 0.118 0.157 0.157 0.157 0.157 0.197 0.197 0.197 0.197 0.197 0.236 0.236 0.236 0.276 0.276 0.276 0.315 0.315 0.315 0.315 0.394 0.394 0.394 0.472 0.472 0.472 0.472 0.472 0.472 0.551 0.551 0.551 0.551 0.630 0.630 0.630 0.630 0.709 0.709 0.709 0.787 0.787 0.945 0.945 0.079 0.079 0.079 0.079 0.079 0.079 0.079 0.079 0.079 0.079 0.079 0.098 0.098 0.098 0.118 0.118 0.118 0.138 0.138 0.138 0.138 0.157 0.157 0.157 0.197 0.197 0.197 0.197 0.197 0.197 0.236 0.236 0.236 0.236 0.276 0.276 0.276 0.276 0.315 0.315 0.315 0.394 0.394 0.472 0.472 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.002 0.003 0.003 NOTES: KM0—KM34 are available with 360° insert. Also available in stainless steel. HM-Series Locknuts are also available. KM-00 SERIES LOCKNUTS 35 36 37 W-00 & W-000 SERIES LOCKWASHER DIMENSIONS For use with N and AN Locknut Series LOCKWASHER DIMENSIONS LOCKWASHER BORE NO. FACE DIA. OVER KEY INSIDE NO. OF DIAMETER TANGS WIDTH DIMENSION TANGS E B S X R MIN. W-00 W-00 W-01 W-02 W-03 W-04 W-05 W-06 W-07 W-08 W-09 W-10 W-11 W-12 W-13 W-14 W-15 W-16 W-17 W-18 W-19 W-20 W-21 W-22 W-24 W-26 W-28 W-30 W-32 W-34 W-36 W-38 W-40 W-44 W-000 W-022 W-024 W-026 W-028 W-030 W-032 W-034 W-036 W-038 W-040 W-044 MIN. W-00 0.406 0.484 0.601 0.679 0.801 0.989 1.193 1.396 1.583 1.792 1.992 2.182 2.400 2.588 2.791 2.973 3.177 3.395 3.582 3.800 3.988 4.192 4.395 4.801 5.191 5.582 5.983 6.389 6.764 7.171 7.577 7.982 8.701 0.625 0.719 0.813 0.938 1.125 1.281 1.500 1.813 2.000 2.281 2.438 2.656 2.844 3.063 3.313 3.563 3.844 4.031 4.281 4.563 4.813 5.000 5.281 5.688 6.188 6.531 7.063 7.438 8.031 8.375 8.781 9.156 9.875 MAX. W-000 W-00 4.921 5.333 5.723 6.129 6.708 7.114 7.508 7.899 8.290 8.774 9.570 0.875 1.016 1.156 1.328 1.531 1.719 1.922 2.250 2.496 2.734 2.922 3.109 3.344 3.578 3.828 4.109 4.375 4.625 4.938 5.219 5.500 5.703 6.063 6.469 7.031 7.438 8.063 8.438 9.063 9.438 9.875 10.313 11.438 MAX. W-000 W-00 5.688 6.188 6.625 7.094 7.719 8.156 8.594 9.000 9.438 9.969 10.406 0.120 0.120 0.120 0.120 0.176 0.176 0.176 0.176 0.290 0.290 0.290 0.290 0.290 0.290 0.290 0.290 0.353 0.353 0.353 0.353 0.353 0.353 0.353 0.353 0.435 0.590 0.590 0.590 0.715 0.715 0.715 0.840 0.940 0.350 0.350 0.469 0.594 0.594 0.594 0.719 0.719 0.719 0.844 0.945 LOCKWASHERS 38 TANG TANG APP. WT. WIDTH THICKNESS (LB./C) T Q V MIN. MIN. W-000 0.334 0.412 0.529 0.607 0.729 0.909 1.093 1.296 1.475 1.684 1.884 2.069 2.267 2.455 2.658 2.831 3.035 3.253 3.418 3.636 3.809 4.013 4.185 4.591 4.961 5.352 5.722 6.128 6.503 6.910 7.316 7.721 8.327 PROJECTION 9 9 11 11 11 13 13 15 15 17 17 17 17 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 MAX. W-00 W-00 0.063 0.063 0.063 0.063 0.063 0.094 0.094 0.094 0.094 0.125 0.125 0.125 0.125 0.125 0.188 0.188 0.188 0.188 0.188 0.188 0.250 0.250 0.250 0.250 0.250 0.250 0.312 0.312 0.312 0.312 0.312 0.312 0.120 0.120 0.120 0.120 0.166 0.166 0.166 0.166 0.234 0.234 0.234 0.234 0.234 0.234 0.234 0.328 0.328 0.328 0.328 0.328 0.328 0.390 0.390 0.390 0.520 0.520 0.520 0.520 0.520 0.645 0.645 0.645 0.878 MIN. W-000 W-00 0.390 0.390 0.390 0.390 0.520 0.520 0.520 0.520 0.520 0.645 0.770 0.032 0.032 0.032 0.032 0.032 0.040 0.040 0.040 0.048 0.048 0.048 0.053 0.053 0.053 0.053 0.062 0.062 0.062 0.084 0.084 0.084 0.084 0.115 0.115 0.115 0.115 0.146 0.146 0.146 0.146 0.146 0.146 0.146 W-000 0.115 0.115 0.115 0.115 0.115 0.115 0.115 0.115 0.115 0.115 0.115 0.50 0.50 0.50 0.80 1.30 1.50 1.50 2.30 3.30 4.30 4.50 4.80 4.80 6.00 6.50 10.00 11.50 12.00 16.80 19.50 20.50 23.80 34.50 39.00 43.00 46.50 71.00 73.50 90.50 93.50 105.00 111.00 118.00 PRW-00 & PRWT-00 SERIES LOCKWASHER DIMENSIONS PRW for use with PRN and PRL Precision Locknut Series. PRWT for use with PRT Precision Locknut Series. LOCKWASHER DIMENSIONS LOCKWASHER NO. THICKNESS BORE Q PRW-00 PRW-01 PRW-02 PRW-03 PRW-04 PRW-05 PRW-06 PRW-065 PRW-07 PRW-08 PRW-09 PRW-10 PRW-11 PRW-12 PRW-13 PRW-14 PRW-15 PRW-16 PRW-17 PRW-18 PRW-19 PRW-20 PRW-21 PRW-22 PRW-24 PRW-26 PRW-28 PRW-30 PRW-32 PRW-34 PRW-36 PRW-38 PRW-40 MIN. 0.034 0.034 0.047 0.047 0.047 0.050 0.050 0.050 0.050 0.059 0.059 0.059 0.059 0.070 0.070 0.070 0.083 0.083 0.083 0.111 0.111 0.111 0.111 0.125 0.145 0.145 0.145 0.180 0.180 0.180 0.180 0.180 0.180 R MAX. 0.042 0.042 0.055 0.055 0.055 0.058 0.058 0.058 0.058 0.067 0.067 0.067 0.067 0.078 0.078 0.078 0.091 0.091 0.091 0.119 0.119 0.119 0.119 0.135 0.155 0.155 0.155 0.195 0.195 0.195 0.195 0.195 0.195 LOCKWASHER DIMENSIONS LOCKWASHER NO. THICKNESS MIN. 0.406 0.484 0.601 0.679 0.801 0.989 1.193 1.333 1.396 1.583 1.792 1.992 2.182 2.400 2.588 2.791 2.973 3.177 3.395 3.582 3.800 3.988 4.192 4.395 4.801 5.191 5.582 5.983 6.389 6.764 7.171 7.577 7.982 BORE Q PRWT-00 PRWT-01 PRWT-02 PRWT-03 PRWT-04 PRWT-05 PRWT-06 PRWT-07 PRWT-08 PRWT-09 PRWT-10 PRWT-11 PRWT-12 PRWT-13 PRWT-14 PRWT-15 PRWT-16 PRWT-17 PRWT-18 MIN. 0.034 0.034 0.034 0.034 0.034 0.042 0.042 0.042 0.054 0.054 0.054 0.054 0.054 0.054 0.054 0.054 0.054 0.054 0.054 MAX. 0.421 0.499 0.616 0.694 0.816 1.009 1.213 1.353 1.416 1.603 1.817 2.017 2.207 2.425 2.613 2.816 3.003 3.207 3.425 3.612 3.830 4.018 4.222 4.425 4.831 5.226 5.617 6.018 6.424 6.799 7.206 7.612 8.017 R MAX. 0.042 0.042 0.042 0.042 0.042 0.050 0.050 0.050 0.064 0.064 0.064 0.064 0.064 0.064 0.064 0.064 0.064 0.064 0.064 MIN. 0.406 0.484 0.601 0.679 0.801 0.989 1.193 1.396 1.583 1.792 1.992 2.182 2.400 2.588 2.791 2.973 3.177 3.395 3.582 MAX. 0.421 0.499 0.616 0.694 0.816 1.009 1.213 1.416 1.603 1.817 2.017 2.207 2.425 2.613 2.816 3.003 3.207 3.425 3.612 FACE DIAMETER W MIN. MAX. 0.625 0.640 0.719 0.734 0.813 0.827 0.938 0.953 1.125 1.140 1.281 1.296 1.500 1.515 1.813 1.827 1.813 1.827 2.000 2.030 2.281 2.311 2.438 2.468 2.656 2.686 2.844 2.874 3.063 3.093 3.313 3.343 3.563 3.593 3.844 3.874 4.031 4.061 4.281 4.326 4.563 4.607 4.813 4.858 5.000 5.045 5.281 5.326 5.688 5.733 6.188 6.233 6.531 6.576 7.063 7.123 7.438 7.498 8.031 8.091 8.375 8.435 8.781 8.841 9.156 9.216 DIAMETER OVER TANGS NO. B +1/16 - 0 15/16 9 1 7/64 9 1 1/4 11 1 13/32 11 1 21/32 11 1 51/64 13 2 1/16 13 2 21/64 15 2 11/32 15 2 37/64 15 2 13/16 17 3 1/32 17 3 3/16 17 3 7/16 17 3 43/64 19 3 29/32 19 4 5/32 19 4 1/2 19 4 25/32 19 5 5/64 19 5 23/64 19 5 5/8 19 5 27/32 19 6 9/64 19 6 45/64 19 7 5/16 19 7 5/8 19 8 9/32 19 8 43/64 19 9 19/64 19 9 21/32 19 10 3/32 19 10 11/16 19 FACE DIAMETER W MIN. MAX. 0.531 0.551 0.625 0.645 0.750 0.770 0.875 0.895 1.000 1.020 1.188 1.208 1.438 1.458 1.656 1.676 1.844 1.864 2.062 2.082 2.250 2.270 2.500 2.520 2.688 2.708 2.875 2.895 3.094 3.114 3.375 3.395 3.594 3.614 3.812 3.832 4.000 4.020 DIAMETER OVER TANGS B +1/16 - 0 57/64 63/64 1 11/64 1 9/32 1 7/16 1 41/64 1 61/64 2 11/64 2 21/64 2 19/32 2 25/32 3 1/16 3 9/32 3 15/32 3 11/16 4 1/32 4 1/4 4 15/32 4 21/32 NO. 9 9 11 11 11 13 13 15 15 17 17 17 17 19 19 19 19 19 19 TANGS WIDTH T MIN. MAX. 0.110 0.120 0.110 0.120 0.110 0.120 0.110 0.120 0.146 0.166 0.146 0.166 0.146 0.166 0.146 0.166 0.146 0.166 0.204 0.234 0.204 0.234 0.204 0.234 0.204 0.234 0.204 0.234 0.204 0.234 0.204 0.234 0.298 0.328 0.298 0.328 0.298 0.328 0.298 0.328 0.298 0.328 0.298 0.328 0.360 0.390 0.360 0.390 0.360 0.390 0.480 0.520 0.480 0.520 0.480 0.520 0.480 0.520 0.480 0.520 0.605 0.645 0.605 0.645 0.605 0.645 PROJECTION Y MIN. MAX. 0.062 0.094 0.062 0.094 0.062 0.094 0.062 0.094 0.062 0.094 0.093 0.125 0.093 0.125 0.093 0.125 0.093 0.125 0.093 0.125 0.125 0.156 0.125 0.156 0.125 0.156 0.125 0.156 0.125 0.156 0.187 0.250 0.187 0.250 0.187 0.250 0.187 0.250 0.187 0.250 0.187 0.250 0.250 0.313 0.250 0.313 0.250 0.313 0.250 0.313 0.250 0.313 0.250 0.313 0.312 0.375 0.312 0.375 0.312 0.375 0.312 0.375 0.312 0.375 0.312 0.375 KEY BENT WIDTH S MIN. MAX. 0.110 0.120 0.110 0.120 0.110 0.120 0.110 0.120 0.156 0.176 0.156 0.176 0.156 0.176 0.156 0.176 0.156 0.176 0.250 0.290 0.250 0.290 0.250 0.290 0.250 0.290 0.250 0.290 0.250 0.290 0.250 0.290 0.250 0.290 0.313 0.353 0.313 0.353 0.313 0.353 0.313 0.353 0.313 0.353 0.313 0.353 0.313 0.353 0.313 0.353 0.375 0.435 0.500 0.590 0.500 0.590 0.500 0.590 0.625 0.715 0.625 0.715 0.625 0.715 0.750 0.840 CLEARANCE X MIN. MAX. 0.334 0.359 0.412 0.437 0.529 0.554 0.607 0.632 0.729 0.754 0.909 0.939 1.093 1.128 1.221 1.256 1.296 1.331 1.475 1.510 1.684 1.724 1.884 1.924 2.069 2.109 2.267 2.307 2.455 2.495 2.658 2.698 2.831 2.867 3.035 3.080 3.253 3.298 3.418 3.463 3.636 3.681 3.809 3.859 4.013 4.063 4.185 4.235 4.591 4.641 4.961 5.016 5.352 5.407 5.722 5.777 6.128 6.183 6.503 6.558 6.910 6.965 7.316 7.371 7.721 7.776 RADIUS Z TANGS WIDTH T MIN. MAX. 0.084 0.104 0.084 0.104 0.084 0.104 0.084 0.104 0.146 0.166 0.146 0.166 0.146 0.166 0.146 0.166 0.204 0.234 0.204 0.234 0.204 0.234 0.204 0.234 0.204 0.234 0.204 0.234 0.204 0.234 0.297 0.327 0.297 0.327 0.297 0.327 0.297 0.327 PROJECTION Y MIN. MAX. 0.062 0.094 0.062 0.094 0.062 0.094 0.062 0.094 0.062 0.094 0.093 0.125 0.093 0.125 0.093 0.125 0.093 0.125 0.125 0.156 0.125 0.156 0.125 0.156 0.125 0.156 0.125 0.156 0.187 0.250 0.187 0.250 0.187 0.250 0.187 0.250 0.187 0.250 KEY BENT WIDTH S MIN. MAX. 0.110 0.120 0.110 0.120 0.110 0.120 0.110 0.120 0.156 0.176 0.156 0.176 0.156 0.176 0.156 0.176 0.280 0.300 0.280 0.300 0.280 0.300 0.280 0.300 0.280 0.300 0.280 0.300 0.280 0.300 0.280 0.300 0.340 0.360 0.340 0.360 0.340 0.360 CLEARANCE X MIN. MAX. 0.333 0.353 0.411 0.431 0.513 0.533 0.591 0.611 0.724 0.744 0.880 0.900 1.084 1.104 1.287 1.307 1.474 1.494 1.693 1.713 1.880 1.900 2.067 2.087 2.255 2.275 2.443 2.463 2.631 2.651 2.813 2.833 3.017 3.037 3.220 3.240 3.380 3.400 RADIUS Z 1/64 1/64 1/64 1/64 1/64 1/64 1/32 1/32 1/32 1/32 1/32 1/32 1/32 3/64 3/64 3/64 3/64 3/64 3/64 3/64 3/64 3/64 3/64 3/64 3/64 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/64 1/64 1/64 1/64 1/64 1/64 1/32 1/32 1/32 1/32 1/32 1/32 3/64 3/64 3/64 3/64 3/64 3/64 3/64 LOCKWASHERS 39 TW-000 SERIES LOCKWASHER DIMENSIONS For use with tapered roller bearings Opposite tab bend Heavy Duty LOCKWASHER DIMENSIONS LOCKWASHER NO. THICKNESS BORE Q TW-100 TW-101 TW-102 TW-103 TW-104 TW-105 TW-106 TW-065 TW-107 TW-108 TW-109 TW-110 TW-111 TW-112 TW-113 TW-114 TW-115 TW-116 TW-117 TW-118 TW-119 TW-120 TW-121 TW-122 TW-124 TW-126 TW-128 TW-130 TW-132 TW-134 TW-136 TW-138 TW-140 MIN. 0.032 0.032 0.048 0.048 0.048 0.052 0.052 0.052 0.052 0.062 0.062 0.062 0.062 0.072 0.072 0.072 0.085 0.085 0.085 0.115 0.115 0.115 0.115 0.130 0.155 0.155 0.155 0.193 0.193 0.193 0.193 0.193 0.193 R MAX. 0.038 0.038 0.054 0.054 0.054 0.058 0.058 0.058 0.058 0.070 0.070 0.070 0.070 0.080 0.080 0.080 0.095 0.095 0.095 0.125 0.125 0.125 0.125 0.140 0.165 0.165 0.165 0.205 0.205 0.205 0.205 0.205 0.205 MIN. 0.406 0.484 0.601 0.679 0.801 0.989 1.193 1.333 1.396 1.583 1.792 1.992 2.182 2.400 2.588 2.791 2.973 3.177 3.395 3.582 3.800 3.988 4.192 4.395 4.801 5.191 5.582 5.983 6.389 6.764 7.171 7.577 7.982 MAX. 0.421 0.499 0.616 0.694 0.816 1.009 1.213 1.353 1.416 1.603 1.817 2.017 2.207 2.425 2.613 2.816 3.003 3.207 3.425 3.612 3.830 4.018 4.222 4.425 4.831 5.226 5.617 6.018 6.424 6.799 7.206 7.612 8.017 FACE DIAMETER W MIN. MAX. 0.625 0.640 0.719 0.734 0.813 0.828 0.938 0.953 1.125 1.140 1.281 1.296 1.500 1.515 1.813 1.828 1.813 1.828 2.000 2.030 2.281 2.311 2.438 2.468 2.656 2.686 2.844 2.874 3.063 3.093 3.313 3.343 3.563 3.593 3.844 3.874 4.031 4.061 4.281 4.326 4.563 4.608 4.813 4.858 5.000 5.045 5.281 5.326 5.688 5.733 6.188 6.233 6.531 6.576 7.063 7.123 7.438 7.498 8.031 8.091 8.375 8.435 8.781 8.841 9.156 9.216 DIAMETER OVER TANGS B +1/16 - 0 57/64 1 1/32 1 5/32 1 11/32 1 9/16 1 45/64 1 61/64 2 15/64 2 1/4 2 31/64 2 23/32 2 59/64 3 3/32 3 21/64 3 9/16 3 13/16 4 3/64 4 25/64 4 5/8 4 61/64 5 15/64 5 31/64 5 45/64 6 6 17/32 7 3/64 7 7/16 8 1/16 8 29/64 9 5/64 9 7/16 9 55/64 10 13/32 NO. 9 9 11 11 11 13 13 15 15 15 17 17 17 17 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 TANGS WIDTH T MIN. MAX. 0.110 0.120 0.110 0.120 0.110 0.120 0.110 0.120 0.146 0.166 0.146 0.166 0.146 0.166 0.146 0.166 0.146 0.166 0.204 0.234 0.204 0.234 0.204 0.234 0.204 0.234 0.204 0.234 0.204 0.234 0.204 0.234 0.298 0.328 0.298 0.328 0.298 0.328 0.298 0.328 0.298 0.328 0.298 0.328 0.360 0.390 0.360 0.390 0.360 0.390 0.480 0.520 0.480 0.520 0.480 0.520 0.480 0.520 0.480 0.520 0.605 0.645 0.605 0.645 0.605 0.645 PROJECTION Y MIN. MAX. 0.062 0.094 0.062 0.094 0.062 0.094 0.062 0.094 0.062 0.094 0.093 0.125 0.093 0.125 0.093 0.125 0.093 0.125 0.093 0.125 0.125 0.156 0.125 0.156 0.125 0.156 0.125 0.156 0.125 0.156 0.187 0.250 0.187 0.250 0.187 0.250 0.187 0.250 0.187 0.250 0.187 0.250 0.250 0.313 0.250 0.313 0.250 0.313 0.250 0.313 0.250 0.313 0.250 0.313 0.312 0.375 0.312 0.375 0.312 0.375 0.312 0.375 0.312 0.375 0.312 0.375 KEY BENT WIDTH S MIN. MAX. 0.110 0.120 0.110 0.120 0.110 0.120 0.110 0.120 0.156 0.176 0.156 0.176 0.156 0.176 0.156 0.176 0.156 0.176 0.250 0.290 0.250 0.290 0.250 0.290 0.250 0.290 0.250 0.290 0.250 0.290 0.250 0.290 0.250 0.290 0.313 0.353 0.313 0.353 0.313 0.353 0.313 0.353 0.313 0.353 0.313 0.353 0.313 0.353 0.313 0.353 0.375 0.435 0.500 0.590 0.500 0.590 0.500 0.590 0.625 0.715 0.625 0.715 0.625 0.715 0.750 0.840 CLEARANCE X MIN. MAX. 0.334 0.359 0.412 0.437 0.513 0.538 0.591 0.616 0.713 0.738 0.897 0.927 1.081 1.116 1.221 1.256 1.284 1.319 1.461 1.196 1.670 1.710 1.870 1.910 2.060 2.100 2.248 2.288 2.436 2.476 2.639 2.679 2.808 2.853 3.012 3.057 3.230 3.275 3.387 3.432 3.605 3.650 3.778 3.828 3.982 4.032 4.170 4.220 4.551 4.601 4.921 4.976 5.312 5.367 5.675 5.730 6.081 6.136 6.456 6.511 6.863 6.918 7.269 7.324 7.674 7.729 RADIUS Z 1/64 1/64 1/64 1/64 1/64 1/64 1/32 1/32 1/32 1/32 1/32 1/32 1/32 3/64 3/64 3/64 3/64 3/64 3/64 3/64 3/64 3/64 3/64 3/64 3/64 1/16 1/16 1/16 1/16 1/16 1/16 1/16 1/16 LOCKWASHERS 40 WTH-00 & WIN-00 SERIES LOCKWASHER DIMENSIONS WTH for use with NTH Locknut Series WIN for use with NIN Locknut Series WTH-00 LOCKWASHER DIMENSIONS LOCKWASHER NO. THICKNESS BORE Q WTH-00 WTH-01 WTH-02 WTH-03 WTH-04 WTH-05 WTH-06 WTH-07 WTH-08 WTH-09 WTH-10 WTH-11 WTH-12 WTH-13 WTH-14 WTH-15 WTH-16 WTH-17 WTH-18 MIN. 0.036 0.036 0.036 0.036 0.036 0.046 0.046 0.046 0.058 0.058 0.058 0.058 0.058 0.058 0.058 0.058 0.058 0.058 0.058 R MAX. 0.044 0.044 0.044 0.044 0.044 0.054 0.054 0.054 0.068 0.068 0.068 0.068 0.068 0.068 0.068 0.068 0.068 0.068 0.068 MIN. 0.406 0.484 0.601 0.679 0.801 0.989 1.193 1.396 1.583 1.792 1.992 2.182 2.400 2.588 2.791 2.973 3.177 3.395 3.582 MAX. 0.421 0.499 0.616 0.694 0.816 1.009 1.213 1.416 1.603 1.817 2.017 2.207 2.425 2.613 2.816 3.003 3.207 3.425 3.612 WIN-00 LOCKWASHER DIMENSIONS LOCKWASHER NO. THICKNESS BORE Q WIN-01 WIN-02 WIN-03 WIN-04 WIN-05 WIN-06 WIN-07 WIN-08 WIN-09 WIN-10 WIN-11 WIN-12 WIN-13 WIN-14 MIN. 0.046 0.046 0.046 0.046 0.046 0.046 0.046 0.058 0.058 0.058 0.058 0.058 0.058 0.058 R MAX. 0.054 0.054 0.054 0.054 0.054 0.054 0.054 0.068 0.068 0.068 0.068 0.068 0.068 0.068 MIN. 0.797 0.922 1.047 1.172 1.297 1.422 1.547 1.672 1.797 1.922 2.047 2.297 2.547 2.797 MAX. 0.828 0.953 1.078 1.203 1.328 1.453 1.578 1.703 1.828 1.953 2.078 2.328 2.578 2.828 FACE DIAMETER W MIN. MAX. 0.531 0.551 0.625 0.645 0.750 0.770 0.875 0.895 1.000 1.020 1.188 1.208 1.438 1.458 1.656 1.676 1.844 1.864 2.062 2.082 2.250 2.270 2.500 2.520 2.688 2.708 2.875 2.895 3.094 3.114 3.375 3.395 3.594 3.614 3.812 3.832 4.000 4.020 DIAMETER OVER TANGS B +0 - 1/16 53/64 59/64 1 3/32 1 13/64 1 3/8 1 9/16 1 55/64 2 5/64 2 1/4 2 1/2 2 11/16 2 61/64 3 3/16 3 3/8 3 19/32 3 59/64 4 9/64 4 23/64 4 35/64 FACE DIAMETER W MIN. MAX. 1.188 1.203 1.313 1.328 1.438 1.453 1.563 1.578 1.688 1.703 1.938 1.953 1.938 1.953 2.188 2.203 2.313 2.328 2.438 2.453 2.688 2.703 2.875 2.890 3.125 3.140 3.375 3.390 DIAMETER OVER TANGS B +0 - 1/16 1 9/16 1 11/16 1 13/16 2 2 1/8 2 3/8 2 3/8 2 5/8 2 3/4 2 7/8 3 1/8 3 7/16 3 11/16 3 15/16 NO. 9 9 11 11 11 13 13 15 15 17 17 17 17 19 19 19 19 19 19 NO. 9 9 11 11 11 13 13 13 15 15 15 17 17 17 LOCKWASHERS 41 TANGS WIDTH T MIN. MAX. 0.084 0.104 0.084 0.104 0.084 0.104 0.084 0.104 0.146 0.166 0.146 0.166 0.146 0.166 0.146 0.166 0.204 0.234 0.204 0.234 0.204 0.234 0.204 0.234 0.204 0.234 0.204 0.234 0.204 0.234 0.297 0.327 0.297 0.327 0.297 0.327 0.297 0.327 PROJECTION Y MIN. MAX. 0.062 0.094 0.062 0.094 0.062 0.094 0.062 0.094 0.062 0.094 0.093 0.125 0.093 0.125 0.093 0.125 0.093 0.125 0.125 0.156 0.125 0.156 0.125 0.156 0.125 0.156 0.125 0.156 0.187 0.250 0.187 0.250 0.187 0.250 0.187 0.250 0.187 0.250 KEY BENT WIDTH S MIN. MAX. 0.110 0.120 0.110 0.120 0.110 0.120 0.110 0.120 0.156 0.176 0.156 0.176 0.156 0.176 0.156 0.176 0.280 0.300 0.280 0.300 0.280 0.300 0.280 0.300 0.280 0.300 0.280 0.300 0.280 0.300 0.280 0.300 0.340 0.360 0.340 0.360 0.340 0.360 CLEARANCE X MIN. MAX. 0.333 0.353 0.411 0.431 0.513 0.533 0.591 0.611 0.724 0.744 0.880 0.900 1.084 1.104 1.287 1.307 1.474 1.494 1.693 1.713 1.880 1.900 2.067 2.087 2.255 2.275 2.443 2.463 2.631 2.651 2.813 2.833 3.017 3.037 3.220 3.240 3.380 3.400 RADIUS Z TANGS WIDTH T MIN. MAX. 0.178 0.198 0.178 0.198 0.178 0.198 0.178 0.198 0.178 0.198 0.178 0.198 0.178 0.198 0.240 0.260 0.240 0.260 0.240 0.260 0.240 0.260 0.240 0.260 0.240 0.260 0.240 0.260 PROJECTION Y MIN. MAX. 0.125 0.156 0.125 0.156 0.125 0.156 0.125 0.156 0.125 0.156 0.125 0.156 0.125 0.156 0.125 0.156 0.125 0.156 0.125 0.156 0.125 0.156 0.187 0.218 0.187 0.218 0.187 0.218 KEY BENT WIDTH S MIN. MAX. 0.168 0.188 0.168 0.188 0.168 0.188 0.168 0.188 0.168 0.188 0.168 0.188 0.168 0.188 0.240 0.260 0.240 0.260 0.240 0.260 0.240 0.260 0.240 0.260 0.240 0.260 0.240 0.260 CLEARANCE X MIN. MAX. 0.687 0.712 0.812 0.837 0.937 0.962 1.062 1.087 1.187 1.212 1.312 1.337 1.437 1.462 1.562 1.587 1.687 1.712 1.812 1.837 1.937 1.962 2.187 2.212 2.437 2.462 2.687 2.712 RADIUS Z 1/64 1/64 1/64 1/64 1/64 1/64 1/32 1/32 1/32 1/32 1/32 1/32 3/64 3/64 3/64 3/64 3/64 3/64 3/64 1/64 1/64 1/64 1/32 1/32 1/32 1/32 1/32 1/32 1/32 1/32 3/64 3/64 3/64 MB-00 SERIES LOCKWASHER DIMENSIONS Metric MB-00 LOCKWASHER DIMENSIONS LOCKWASHER NO. MB-0 MB-1 MB-2 MB-3 MB-4 MB-4.4 MB-5 MB-5.6 MB-6 MB-6.4 MB-7 MB-8 MB-9 MB-10 MB-11 MB-12 MB-13 MB-14 MB-15 MB-16 MB-17 MB-18 MB-19 MB-20 MB-21 MB-22 MB-23 MB-24 MB-25 MB-26 MB-27 MB-28 MB-29 MB-30 MB-31 MB-32 MB-33 MB-34 MB-36 MB-38 MB-40 MB-44 MB-48 MB-52 MB-56 BORE R NOM. 0.394 0.472 0.591 0.669 0.787 0.866 0.984 1.102 1.181 1.260 1.378 1.575 1.772 1.968 2.165 2.362 2.559 2.756 2.953 3.150 3.346 3.543 3.740 3.937 4.134 4.331 4.528 4.724 4.921 5.118 5.315 5.512 5.709 5.906 6.102 6.299 6.496 6.693 7.087 7.480 7.874 8.661 9.449 10.236 11.024 FACE DIAMETER E MIN. 0.532 0.669 0.827 0.945 1.024 1.102 1.260 1.417 1.496 1.575 1.732 1.968 2.205 2.402 2.638 2.874 3.110 3.346 3.543 3.740 4.016 4.252 4.449 4.724 4.961 5.236 5.394 5.433 5.827 5.866 6.299 6.299 6.732 6.732 7.165 7.165 7.598 7.598 7.992 8.425 8.898 9.843 10.630 11.811 12.598 DIAMETER OVER TANGS B MAX. 0.827 0.984 1.102 1.260 1.417 1.496 1.654 1.811 1.929 2.047 2.244 2.241 2.717 2.913 3.189 3.386 3.622 3.858 4.094 4.409 4.685 4.961 5.236 5.591 5.709 6.063 6.260 6.457 6.693 6.890 7.283 7.559 7.953 8.071 8.346 8.543 8.740 9.134 9.528 9.921 10.315 11.496 12.283 13.465 14.252 KEY WIDTH S MAX. 0.118 0.118 0.157 0.157 0.157 0.157 0.197 0.197 0.197 0.197 0.236 0.236 0.236 0.236 0.315 0.315 0.315 0.315 0.315 0.394 0.394 0.394 0.394 0.472 0.472 0.472 0.472 0.551 0.551 0.551 0.551 0.630 0.630 0.630 0.630 0.709 0.709 0.709 0.787 0.787 0.787 0.945 0.945 1.102 1.102 INSIDE DIMENSION X NOM. 0.335 0.413 0.532 0.610 0.728 0.807 0.906 1.024 1.083 1.161 1.280 1.476 1.673 1.870 2.067 2.264 2.461 2.618 2.815 3.012 3.209 3.406 3.602 3.799 3.957 4.154 4.350 4.528 4.724 4.921 5.118 5.315 5.512 5.709 5.807 6.063 6.201 6.457 6.850 7.244 7.638 8.368 9.173 9.961 10.748 MATERIAL THICKNESS Q NOM. 0.039 0.039 0.039 0.039 0.039 0.039 0.049 0.049 0.049 0.049 0.049 0.049 0.049 0.049 0.059 0.059 0.059 0.059 0.059 0.071 0.071 0.071 0.071 0.071 0.071 0.071 0.079 0.079 0.079 0.079 0.079 0.079 0.079 0.079 0.098 0.098 0.098 0.098 0.098 0.098 0.098 0.118 0.118 0.118 0.118 TANG WIDTH T MAX. 0.118 0.118 0.157 0.157 0.157 0.157 0.197 0.197 0.197 0.197 0.197 0.236 0.236 0.236 0.276 0.276 0.276 0.315 0.315 0.315 0.315 0.394 0.394 0.394 0.472 0.472 0.472 0.472 0.472 0.472 0.551 0.551 0.551 0.551 0.630 0.630 0.630 0.630 0.709 0.709 0.709 0.787 0.787 0.945 0.945 NO. OF TANGS 9 11 11 11 11 11 13 13 13 15 13 13 13 13 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 19 19 19 19 19 19 19 19 19 19 19 LOCKWASHERS 43 P-000 SERIES LOCKPLATE DIMENSIONS For use with SNP-00 and SNP-3100 series adapters LOCKPLATE DIMENSIONS LOCKPLATE NO. CAPSCREW SIZE J2 LOCKNUT NO. P-48 P-52 P-56 P-60 P-64 P-68 P-72 P-76 P-80 P-84 P-88 P-92 P-96 P-500 P-530 P-560 P-600 P-630 P-670 P-710 P-750 P-800 P-850 P-900 P-950 5/16 -- 18 x 5/8 5/16 -- 18 x 5/8 5/16 -- 18 x 5/8 3/8 -- 16 x 3/4 3/8 -- 16 x 3/4 3/8 -- 16 x 3/4 3/8 -- 16 x 3/4 1/2 -- 13 x 7/8 1/2 -- 13 x 7/8 1/2 -- 13 x 7/8 5/8 -- 11 x 1 5/8 -- 11 x 1 5/8 -- 11 x 1 1/4 5/8 -- 11 x 1 1/4 5/8 -- 11 x 1 1/4 5/8 -- 11 x 1 1/4 5/8 -- 11 x 1 1/4 5/8 -- 11 x 1 1/4 5/8 -- 11 x 1 1/4 5/8 -- 11 x 1 1/4 5/8 -- 11 x 1 1/4 5/8 -- 11 x 1 1/4 3/4 -- 10 x 1 1/2 3/4 -- 10 x 1 1/2 3/4 -- 10 x 1 1/2 N-048 N-052 N-056 N-060 N-064 N-068 N-072 N-076 N-080 N-084 N-088 N-092 N-096 N-500 N-530 N-560 N-600 N-630 N-670 N-710 N-750 N-800 N-850 N-900 N-950 NOTES: MS-Series Metric Clamps are also available. LOCKPLATES 44 45 SAF 200 and 300 SERIES CAST IRON PILLOW BLOCKS STRAIGHT BORE MOUNTING SAF-200 SERIES SHAFT DIA. S-2 IN. 2 3/8 2 9/16 3 1/16 3 7/16 3 7/16 3 5/8 3 5/8 3 15/16 3 15/16 4 1/8 4 1/8 4 1/2 4 1/2 4 7/8 5 5/16 5 7/8 6 1/4 6 5/8 7 7 7/16 7 13/16 8 3/8 8 3/4 9 9/16 S-3 IN. PILLOW BLOCK STABILIZING HOUSING ONLY RING S-2 SHAFT TRIPLE SEAL S-3 SHAFT 1 REQUIRED 1 REQUIRED 1 REQUIRED LOCKNUT LOCKWASHER COMPLETE APP. WT. NO. NO. PILLOW BLOCK (LB.) NO. 1 7/8 2 1/16 2 7/16 2 13/16 2 13/16 3 3 3 3/16 3 3/16 3 3/8 3 3/8 3 13/16 3 13/16 4 3/16 4 9/16 4 15/16 5 5/16 5 3/4 6 1/16 6 7/16 6 7/8 7 1/4 7 5/8 8 5/16 SAF210* SAF211* SAF213* SAF215* FSAF215 SAF216* FSAF216 SAF 217* FSAF217 SAF 218* FSAF218 SAF220* FSAF220 SAF222 SAF224 SAF226 SAF228 SAF230 SAF232 SAF234 SAF236 SAF238 SAF240 SAF244 SR-10-0 SR-11-0 SR-13-0 SR-15-0 SR-15-0 SR-16-13 SR-16-13 SR-17-14 SR-17-14 SR-18-15 SR-18-15 SR-20-17 SR-20-17 SR-22-19 SR-24-20 SR-26-0 SR-28-0 SR-30-0 SR-32-0 SR-34-0 SR-36-30 SR-38-32 SR-40-34 SR-44-38 LER35 LER40 LER55 LER79 LER79 LER82 LER82 LER89 LER89 LER96 LER96 LER118 LER118 LER121 LER127 LER136 LER144 LER151 LER156 LER161 LER165 LER171 LER175 LER179 LER23 LER27 LER37 LER456 LER456 LER54 LER54 LER63 LER63 LER72 LER72 LER106 LER106 LER113 LER119 LER122 LER127 LER134 LER142 LER148 LER154 LER160 LER164 LER170 N10 N11 N13 AN15 AN15 AN16 AN16 AN17 AN17 AN18 AN18 AN20 AN20 AN22 AN24 AN26 AN28 AN30 AN32 AN34 AN36 AN38 AN40 N44 W10 W11 W13 W15 W15 W16 W16 W17 W17 W18 W18 W20 W20 W22 W24 W26 W28 W30 W32 W34 W36 W38 W40 W44 SAF22210 SAF22211 SAF22213 SAF22215 SAF22215 SAF22216 SAF22216 SAF22217 FSAF22217 SAF22218 FSAF22218 SAF22220 FSAF22220 SAF22222 SAF22224 SAF22226 SAF22228 SAF22230 SAF22232 SAF22234 SAF22236 SAF22238 SAF22240 SAF22244 12 14 21 24 24 35 35 43 43 50 50 71 71 81 90 127 149 175 210 280 305 350 420 590 2 13/16 3 3/16 3 3/16 3 3/8 3 13/16 4 3/16 4 9/16 4 15/16 5 5/16 5 3/4 6 1/16 6 7/16 6 7/8 7 1/4 7 5/8 SAF315 SAF317* FSAF317 SAF318 SAF320 SAF322 SAF324 SAF326 SAF328 SAF330 SAF332 SAF334 SAF336 SAF338 SAF340 SR-18-5 SR-20-17 SR-20-17 SR-21-18 SR-24-20 SR-0-22 SR-0-24 SR-0-26 SR-0-28 SR-36-30 SR-38-32 SR-40-34 SR-0-36 SR-44-38 SR-0-40 LER79 LER109 LER109 LER112 LER118 LER121 LER127 LER136 LER144 LER151 LER156 LER161 LER165 LER171 LER175 LER46 LER188 LER188 LER191 LER106 LER113 LER119 LER122 LER127 LER134 LER142 LER148 LER154 LER160 LER164 AN15 AN17 AN17 AN18 AN20 AN22 AN24 AN26 AN28 AN30 AN32 AN34 AN36 AN38 AN40 W15 W17 W17 W18 W20 W22 W24 W26 W28 W30 W32 W34 W36 W38 W40 SAF22315 SAF22317 FSAF22317 SAF22318 SAF22320 SAF22322 SAF22324 SAF22326 SAF22328 SAF22330 SAF22332 SAF22334 SAF22336 SAF22338 SAF22340 53 80 80 92 109 145 195 235 300 335 105 465 525 635 700 SAF-300 SERIES 3 7/16 3 15/16 3 15/16 4 1/8 4 1/2 4 7/8 5 5/16 5 7/8 6 1/4 6 5/8 7 7 7/16 7 11/16 8 3/8 8 3/4 NOTES: Triple seal rings (LER series) and stabilizing ring (SR series) are included with the pillow block. Stabilizing ring used only for “fixed” mounting, not used for “free” mounting. Available in ductile iron as well (SAFD series) * Pillow blocks with 2-hole mounting base, all others have 4-hole mounting base. PILLOW BLOCKS 46 SAF 200 and 300 SERIES CAST IRON PILLOW BLOCKS STRAIGHT BORE MOUNTING SAF-200 SERIES PILLOW BLOCK HOUSING ONLY BASE BOLTS REQUIRED A B C D E MAX. SAF210 SAF211 SAF213 SAF215 FSAF215 SAF216 FSAF216 SAF217 FSAF217 SAF218 FSAF218 SAF220 FSAF220 SAF222 SAF224 SAF226 SAF228 SAF230 SAF232 SAF234 SAF236 SAF238 SAF240 SAF244 2 1/2 2 3/4 3 3 1/4 3 1/4 3 1/2 3 1/2 3 3/4 3 3/4 4 4 4 1/2 4 1/2 4 15/16 5 1/4 6 6 6 5/16 6 11/16 7 1/16 7 1/2 7 7/8 8 1/4 9 1/2 8 1/4 9 5/8 11 11 1/4 11 1/4 13 13 13 13 13 3/4 13 3/4 15 1/4 15 1/4 16 1/2 16 1/2 18 3/8 20 1/8 21 1/4 22 24 3/4 26 3/4 28 29 1/2 32 3/4 2 2 3 3 3 3 3 3 3 3 3 4 4 4 4 5 5 6 6 6 7 7 8 8 4 4 1/2 4 1/2 4 3/4 5 1/4 6 6 5/16 6 11/16 7 1/16 7 1/2 7 7/8 8 1/4 8 7/8 9 1/2 9 7/8 13 15 15 15 16 18 21 22 24 26 28 29 31 32 34 3 4 4 4 4 5 6 6 6 7 7 8 8 8 9 3/8 3/4 1/8 1/8 1/8 1/2 1/2 1/2 1/2 7/8 7/8 3/8 3/8 3/4 3/4 1/8 7/8 1/4 1/4 3/4 1/8 1/2 3/4 F H L NO. SIZE 7/16 5/8 5/8 5/8 1/2 3/4 5/8 3/4 5/8 3/4 5/8 7/8 3/4 3/4 3/4 7/8 MIN. 15/16 15/16 1 1 1/8 1 1/8 1 3/16 1 3/16 1 1/4 1 1/4 1 1/2 1 1/2 1 3/4 1 11/16 2 2 1/8 2 3/8 2 3/8 2 1/2 2 5/8 2 13/16 3 3 1/8 3 3/8 3 3/4 7 7 7/8 9 1/2 9 5/8 9 5/8 11 11 11 11 11 5/8 11 5/8 13 1/8 13 1/8 14 7/16 14 1/2 16 17 1/8 18 1/4 19 1/4 21 5/8 23 5/8 24 3/8 25 27 7/8 6 1/2 7 3/8 8 1/8 8 5/8 8 5/8 9 5/8 9 5/8 9 7/8 9 7/8 10 3/8 10 3/8 11 5/8 11 5/8 12 11/16 13 1/4 14 5/8 16 17 17 3/8 19 3/8 20 7/8 21 5/8 22 1/2 24 3/4 --------1 7/8 --2 1/8 --2 1/8 --2 1/8 --2 3/8 2 3/4 2 3/4 3 1/4 3 3/8 3 3/4 3 3/4 4 1/4 4 5/8 4 1/2 5 5 1/4 4 11/16 5 1/32 5 25/32 6 3/8 6 3/8 6 7/8 6 7/8 7 1/4 7 1/4 7 3/4 7 3/4 8 11/16 8 11/16 9 9/16 10 1/4 11 9/16 11 3/4 12 1/2 13 5/16 14 9/16 15 1/2 15 11/16 17 3/16 19 5/8 3 7/16 3 3/4 4 5/16 4 3/4 4 3/4 4 7/8 4 7/8 4 7/8 4 7/8 6 1/8 6 1/8 5 7/8 5 7/8 6 1/4 7 1/4 7 7/8 7 5/8 8 1/4 8 5/8 9 1/4 9 11/16 10 5/8 10 13/16 11 1/2 2 2 2 2 4 2 4 2 4 2 4 2 4 4 4 4 4 4 4 4 4 4 4 4 1 1 1 2 2 2 2 2 2 3 3 3 3 3 4 11 13 13 13 14 16 18 19 21 23 24 25 26 28 29 10 11 11 12 13 14 17 17 19 20 21 22 24 24 26 ----2 3/8 2 1/4 2 3/4 3 1/4 3 3/4 3 3/4 4 1/4 4 5/8 4 1/2 5 5 1/4 5 1/4 5 1/2 7 13/16 8 11/16 8 11/16 9 3/16 10 1/4 11 9/16 12 1/2 13 5/16 14 9/16 15 1/2 15 11/16 17 3/16 18 1/2 19 5/8 20 3/16 6 1/8 6 5/8 6 5/8 6 7/8 7 1/4 7 7/8 8 1/4 8 5/8 9 1/4 9 11/16 10 5/8 10 13/16 11 1/4 11 1/2 12 1/4 2 2 4 4 4 4 4 4 4 4 4 4 4 4 4 1 1 1 1 1 1 1/4 1 1/4 1 1/2 SAF-300 SERIES SAF315 SAF317 FSAF317 SAF318 SAF320 SAF322 SAF324 SAF326 SAF328 SAF330 SAF332 SAF334 SAF336 SAF338 SAF340 3/4 1/4 1/4 1/2 1/2 3/8 1/4 3/4 3/4 1/2 1/4 3/4 1/4 7/8 3/8 3/8 3/8 3/4 1/8 1/4 1/4 3/4 1/8 1/2 1/4 3/4 5/16 3/4 3/4 1/8 3/8 1/2 5/8 1/4 1/8 3/8 1/2 3/4 3/32 5/8 1/8 1/8 1/2 1/2 1/4 1/4 5/8 5/8 3/8 5/8 1/8 1/2 3/8 5/8 5/8 1/4 5/8 3/8 3/8 7/8 5/8 1/2 3/4 1/4 5/8 7/8 3/4 3/4 3/4 7/8 1 1 1 1 1 1 1 1 1 1/4 1/4 1/4 1/2 1/2 PILLOW BLOCKS 47 SAF 500 and 600 SERIES CAST IRON PILLOW BLOCKS TAPERED BORE/ADAPTER MOUNTING SAF-500 SERIES SHAFT DIA. PILLOW BLOCK STABILIZING S-1 IN. HOUSING ONLY RING 1 11/16 1 15/16 2 3/16 2 7/16 2 7/16 2 11/16 2 11/16 2 15/16 2 15/16 3 3/16 3 3/16 3 7/16 3 7/16 3 15/16 4 3/16 4 7/16 4 15/16 5 3/16 5 7/16 5 15/16 6 7/16 6 15/16 7 3/16 7 15/16 TRIPLE SEAL COMPLETE ADAPTER APP. WT. PILLOW BLOCK NO. (LB.) 1 REQUIRED 2 REQUIRED NO. SAF510** SAF511** SAF513** SAF515* FSAF515 SAF516* FSAF516 SAF517* FSAF517 SAF518* FSAF518 SAF520* FSAF520 SAF522 SAF524 SAF526 SAF528 SAF530 SAF532 SAF534 SAF536 SAF538 SAF540 SAF544 SR-10-8 SR-11-0 SR-13-0 SR-15-0 SR-15-0 SR-16-13 SR-16-13 SR-17-14 SR-17-14 SR-18-15 SR-18-15 SR-20-17 SR-20-17 SR-22-19 SR-24-20 SR-26-0 SR-28-0 SR-30-0 SR-32-0 SR-34-0 SR-36-30 SR-38-32 SR-40-34 SR-44-38 LER20 LER24 LER29 LER37 LER37 LER44 LER44 LER53 LER53 LER69 LER69 LER102 LER102 LER109 LER113 LER117 LER122 LER125 LER130 LER140 LER148 LER155 LER159 LER167 SAF22510 SAF22511 SAF22513 SAF22515 FSAF22515 SAF22516 FSAF22516 SAF22517 FSAF22517 SAF22518 FSAF22518 SAF22520 FSAF22520 SAF22522 SAF22524 SAF22526 SAF22528 SAF22530 SAF22532 SAF22534 SAF22536 SAF22538 SAF22540 SAF22544 SNW-10 SNW-11 SNW-13 SNW-15 SNW-15 SNW-16 SNW-16 SNW-17 SNW-17 SNW-18 SNW-18 SNW-20 SNW-20 SNW-22 SNW-24 SNW-26 SNW-28 SNW-30 SNW-32 SNW-34 SNW-36 SNW-38 SNW-40 SNW-44 12 14 21 24 32 37 37 40 40 49 49 65 65 81 94 137 159 189 225 300 330 375 445 615 SAF615 SAF617* FSAF617 SAF618 SAF620 SAF622 SAF624 SAF626 SAF628 SAF630 SAF632 SAF634 SAF636 SAF638 SAF640 SR-18-15 SR-20-17 SR-20-17 SR-21-18 SR-24-20 SR-0-22 SR-0-24 SR-0-26 SR-0-28 SR-36-30 SR-38-32 SR-40-34 SR-0-36 SR-44-38 SR-0-40 LER37 LER184 LER184 LER188 LER102 LER109 LER113 LER117 LER122 LER125 LER130 LER140 LER148 LER155 LER159 SAF22615 SAF22617 FSAF22617 SAF22618 SAF22620 SAF22622 SAF22624 SAF22626 SAF22628 SAF22630 SAF22632 SAF22634 SAF22636 SAF22638 SAF22640 SNW-115 SNW-117 SNW-117 SNW-118 SNW-120 SNW-122 SNW-124 SNW-126 SNW-128 SNW-130 SNW-132 SNW-134 SNW-136 SNW-138 SNW-140 55 81 81 90 113 151 201 245 310 350 420 485 545 665 725 SAF-600 SERIES 2 7/16 2 15/16 2 15/16 3 3/16 3 7/16 3 15/16 4 3/16 4 7/16 4 15/16 5 3/16 5 7/16 5 15/16 6 7/16 6 15/16 7 3/16 NOTES: Triple seal rings (LER series) and stabilizing ring (SR series) are included with the pillow block. Stabilizing ring used only for “fixed” mounting, not used for “free” mounting. Available in ductile iron as well (SAFD series) * Pillow blocks with 2-hole mounting base, all others have 4-hole mounting base. ** 2-Bolt cap and 2-bolt base. PILLOW BLOCKS 48 SAF 500 and 600 SERIES CAST IRON PILLOW BLOCKS TAPERED BORE/ADAPTER MOUNTING SAF-500 SERIES PILLOW BLOCK HOUSING ONLY BASE BOLTS REQUIRED A B C D E F MAX. SAF510** SAF511** SAF513** SAF515* FSAF515 SAF516* FSAF516 SAF517* FSAF517 SAF518* FSAF518 SAF520* FSAF520 SAF522 SAF524 SAF526 SAF528 SAF530 SAF532 SAF534 SAF536 SAF538 SAF540 SAF544 2 1/2 2 3/4 3 3 1/4 3 1/4 3 1/2 3 1/2 3 3/4 3 3/4 4 4 4 1/2 4 1/2 4 15/16 5 1/4 6 6 6 5/16 6 11/16 7 1/16 7 1/2 7 7/8 8 1/4 9 1/2 8 1/4 9 5/8 11 11 1/4 11 1/4 13 13 13 13 13 3/4 13 3/4 15 1/4 15 1/4 16 1/2 16 1/2 18 3/8 20 1/8 21 1/4 22 24 3/4 26 3/4 28 29 1/2 32 3/4 2 2 3 3 3 3 3 3 3 3 3 4 4 4 4 5 5 6 6 6 7 7 8 8 3/8 3/4 1/8 1/8 1/8 1/2 1/2 1/2 1/2 7/8 7/8 3/8 3/8 3/4 3/4 1/8 7/8 1/4 1/4 3/4 1/8 1/2 13 15 15 15 16 18 21 22 24 26 28 29 31 32 34 3 4 4 4 4 5 6 6 6 7 7 8 8 8 9 7/8 3/8 3/8 3/8 3/4 1/8 1/4 1/4 3/4 1/8 1/2 3/4 H L NO. SIZE MIN. 15/16 15/16 1 1 1/8 1 1/8 1 3/16 1 3/16 1 1/4 1 1/4 1 1/2 1 1/2 1 3/4 1 11/16 2 2 1/8 2 3/8 2 3/8 2 1/2 2 5/8 2 13/16 3 3 1/8 3 3/8 3 3/4 7 7 7/8 9 1/2 9 5/8 9 5/8 11 11 11 11 11 5/8 11 5/8 13 1/8 13 1/8 14 7/16 14 1/2 16 17 1/8 18 1/4 19 1/4 21 5/8 23 5/8 24 3/8 25 27 7/8 6 1/2 7 3/8 8 1/8 8 5/8 8 5/8 9 5/8 9 5/8 9 7/8 9 7/8 10 3/8 10 3/8 11 5/8 11 5/8 12 11/16 13 1/4 14 5/8 16 17 17 3/8 19 3/8 20 7/8 21 5/8 22 1/2 24 3/4 ----1 -2 -2 -2 -2 2 2 3 3 3 3 4 4 4 5 5 1 1 1 2 2 2 2 2 2 3 3 3 3 3 4 11 13 13 13 14 16 18 19 21 23 24 25 26 27 29 10 11 11 12 13 14 17 17 19 20 21 22 24 24 26 --2 2 2 3 3 3 4 4 4 5 5 5 5 7/8 1/8 1/8 1/8 3/8 3/4 3/4 1/4 3/8 3/4 3/4 1/4 5/8 1/2 1/4 4 11/16 5 1/32 5 25/32 6 3/8 6 3/8 6 7/8 6 7/8 7 1/4 7 1/4 7 3/4 7 3/4 8 11/16 8 11/16 9 9/16 10 1/4 11 9/16 11 3/4 12 1/2 13 5/16 14 9/16 15 1/2 15 11/16 17 3/16 19 5/8 3 7/16 3 3/4 4 5/16 4 3/4 4 3/4 4 7/8 4 7/8 4 7/8 4 7/8 6 1/8 6 1/8 5 7/8 5 7/8 6 1/4 7 1/4 7 7/8 7 5/8 8 1/4 8 5/8 9 1/4 9 11/16 10 5/8 10 5/8 11 1/2 2 2 2 2 4 2 4 2 4 2 4 2 4 4 4 4 4 4 4 4 4 4 4 4 7 13/16 8 11/16 8 11/16 9 3/16 10 1/4 11 9/16 12 1/2 13 5/16 14 9/16 15 1/2 15 11/16 17 3 /16 18 1/2 19 5/8 20 3/16 6 1/8 6 5/8 6 5/8 6 7/8 7 1/4 7 7/8 8 1/4 8 5/8 9 1/4 9 11/16 10 5/8 10 13/16 11 1/4 11 1/2 12 1/4 2 2 4 4 4 4 4 4 4 4 4 4 4 4 4 7/16 5/8 5/8 5/8 1/2 3/4 5/8 3/4 5/8 3/4 5/8 7/8 3/4 3/4 3/4 7/8 1 1 1 1 1 1 1/4 1 1/4 1 1/2 SAF-600 SERIES SAF615 SAF617* FSAF617 SAF618 SAF620 SAF622 SAF624 SAF626 SAF628 SAF630 SAF632 SAF634 SAF636 SAF638 SAF640 4 4 1/2 4 1/2 4 3/4 5 1/4 6 6 5/16 6 11/16 7 1/16 7 1/2 7 7/8 8 1/4 8 7/8 9 1/2 9 7/8 3/4 1/4 1/4 1/2 1/2 3/8 1/4 3/4 3/4 1/2 1/4 3/4 1/4 1/4 3/4 5/16 3/4 3/4 1/8 3/8 1/2 5/8 3/4 1/8 3/8 1/2 3/4 3/32 5/8 1/8 1/8 1/2 1/2 1/4 1/4 5/8 5/8 3/8 5/8 7/8 1/2 3/8 5/8 5/8 1/4 5/8 3/8 3/8 7/8 5/8 1/2 1/4 1/4 3/8 1/4 3/4 1/4 3/4 3/4 1/4 5/8 1/2 1/4 1/4 1/2 5/8 7/8 3/4 3/4 3/4 7/8 1 1 1 1 1 1 1 1 1 1/4 1/4 1/4 1/2 1/2 PILLOW BLOCKS 49 SAF 230 SERIES CAST IRON PILLOW BLOCKS TAPERED BORE/ADAPTER MOUNTING Large Bore SAF-230 SERIES SHAFT DIA. PILLOW BLOCK SHAFT STABILIZING S-1 IN. HOUSING ONLY DIA. RING 4 3/16 4 7/16 4 15/16 5 7/16 6 15/16 7 3/16 7 15/16 8 7/16 8 1/2 8 15/16 9 9 7/16 9 1/2 9 15/16 10 10 7/16 10 1/2 SAF024 SAF026 SAF028 SAF032 SAF038 SAF040 SAF044 SAF048 SAF048 SAF048 SAF048 SAF052 SAF052 SAF056 SAF056 SAF056 SAF056 8 7/16 8 1/2 8 15/16 9 9 7/16 9 1/2 9 15/16 10 10 7/16 10 1/2 TRIPLE SEAL 1 REQUIRED 2 REQUIRED SR-20-17 SR-22-19 SR-0-20 SR-0-22 SR-32-0 SR-34-0 SR-38-32 A8897 A8897 A8897 A8897 A8898 A8898 A8819 A8819 A8819 A8819 LER113 LER117 LER122 LER130 LER155 LER159 LER167 LER526 LER527 LER529 LER530 LER178-1 LER178 ER751 ER705 ER745 ER710 COMPLETE ADAPTER APP. WT. PILLOW BLOCK NO. (LB.) SNW-3024 SNW-3026 SNW-3028 SNW-3032 SNW-3038 SNW-3040 SNW-3044 SNP-3048 SNP-3048 SNP-3048 SNP-3048 SNP-3052 SNP-3052 SNP-3056 SNP-3056 SNP-3056 SNP-3056 60 76 90 132 220 295 370 430 428 422 420 587 585 640 635 625 620 NO. SAF23024 SAF23026 SAF23028 SAF23032 SAF23038 SAF23040 SAF23044 SAF23048 SAF23048 SAF23048 SAF23048 SAF23052 SAF23052 SAF23056 SAF23056 SAF23056 SAF23056 NOTES: Triple seal rings (LER series) and stabilizing ring (SR series) are included with the pillow block. Stabilizing ring used only for “fixed” mounting, not used for “free” mounting. * Pillow blocks with 2-hole mounting base, all others have 4-hole mounting base. PILLOW BLOCKS 50 SAF 230 SERIES CAST IRON PILLOW BLOCKS TAPERED BORE/ADAPTER MOUNTING SAF-230 SERIES PILLOW BLOCK SHAFT HOUSING ONLY DIA. BASE BOLTS REQUIRED A B C D E MAX. SAF024 SAF026 SAF028 SAF032 SAF038 SAF040 SAF044 SAF048 SAF048 SAF048 SAF048 SAF052 SAF052 SAF056 SAF056 SAF056 SAF056 8 7/16 8 1/2 8 15/16 9 9 7/16 9 1/2 9 15/16 10 10 7/16 10 1/2 4 1/2 4 15/16 5 1/4 6 6 11/16 7 1/16 7 7/8 8 1/4 8 1/4 8 1/4 8 1/4 9 1/2 9 1/2 9 7/8 9 7/8 9 7/8 9 7/8 15 16 16 18 22 24 28 29 29 29 29 32 32 34 34 34 34 1/4 1/2 1/2 3/8 3/4 1/2 1/2 1/2 1/2 3/4 3/4 1/4 1/4 1/4 1/4 4 4 4 5 6 6 7 8 8 8 8 8 8 9 9 9 9 3/8 3/4 3/4 1/8 1/4 3/4 1/2 3/4 3/4 1 3/4 2 2 1/8 2 3/8 2 5/8 2 13/16 3 1/8 3 3/8 3 3/8 3 3/8 3 3/8 3 3/4 3 3/4 4 3/32 4 3/32 4 3/32 4 3/32 13 14 14 16 19 21 24 25 25 25 25 27 27 29 29 29 29 1/8 7/16 1/2 1/4 5/8 3/8 7/8 7/8 1/2 1/2 1/2 1/2 F H L NO. 3/8 3/4 3/4 1/4 3/4 1/2 1/2 8 11/16 9 9/16 10 1/4 11 9/16 13 5/16 14 9/16 15 11/16 17 3/16 17 3/16 17 3/16 17 3/16 19 5/8 19 5/8 20 3/16 20 3/16 20 3/16 20 3/16 5 7/8 6 1/4 7 1/4 7 7/8 8 5/8 9 1/4 10 5/8 10 13/16 10 13/16 10 13/16 10 13/16 11 1/2 11 1/2 12 1/4 12 1/4 12 1/4 12 1/4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 SIZE MIN. 11 12 13 14 17 19 21 22 22 22 22 24 24 26 26 26 26 5/8 5/8 1/4 5/8 3/8 3/8 5/8 1/2 1/2 1/2 1/2 3/4 3/4 1/4 1/4 1/4 1/4 2 2 2 3 3 4 4 5 5 5 5 5 5 5 5 5 5 1/4 1/4 1/2 1/2 1/2 1/2 3/4 3/4 3/4 7/8 1 1 1 1 1 1 1 1 1 1 1 1 1/4 1/4 1/4 1/4 1/2 1/2 1/2 1/2 1/2 1/2 PILLOW BLOCKS 51 SAFS 200 AND 500 SERIES CAST STEEL PILLOW BLOCKS STRAIGHT BORE MOUNTING and TAPERED BORE/ADAPTER MOUNTING SAFS-200 SERIES STRAIGHT BORE MOUNTING SHAFT DIA. S-2 IN. 3 15/16 3 15/16 4 1/8 4 1/8 4 1/2 4 1/2 4 7/8 5 5/16 5 7/8 6 1/4 6 5/8 7 7 7/16 7 13/16 8 3/8 8 3/4 9 9/16 S-3 IN. 3 3/16 3 3/16 3 3/8 3 3/8 3 13/16 3 13/16 4 3/16 4 9/16 4 15/16 5 5/16 5 3/4 6 1/16 6 7/16 6 7/8 7 1/4 7 5/8 8 5/16 PILLOW BLOCK STABILIZING HOUSING ONLY RING S-2 SHAFT S-3 SHAFT 1 REQUIRED 1 REQUIRED 1 REQUIRED SR-17-14 SR-17-14 SR-18-15 SR-18-15 SR-20-17 SR-20-17 SR-22-19 SR-24-20 SR-26-0 SR-28-0 SR-30-0 SR-32-0 SR-34-0 SR-36-30 SR-38-32 SR-40-34 SR-44-38 LER89 LER89 LER96 LER96 LER118 LER118 LER121 LER127 LER136 LER144 LER151 LER156 LER161 LER165 LER171 LER175 LER179 LER63 LER63 LER72 LER72 LER106 LER106 LER113 LER119 LER122 LER127 LER134 LER142 LER148 LER154 LER160 LER164 LER170 SAFS217* FSAFS217 SAFS218* FSAFS218 SAFS220* FSAFS220 SAFS222 SAFS224 SAFS226 SAFS228 SAFS230 SAFS232 SAFS234 SAFS236 SAFS238 SAFS240 SAFS244 TRIPLE SEAL LOCKNUT LOCKWASHER COMPLETE APP. WT. NO. NO. PILLOW BLOCK (LB.) NO. AN17 AN17 AN18 AN18 AN20 AN20 AN22 AN24 AN26 AN28 AN30 AN32 AN34 AN36 AN38 AN40 N44 W17 W17 W18 W18 W20 W20 W22 W24 W26 W28 W30 W32 W34 W36 W38 W40 W44 SAFS22217 FSAFS22217 SAFS22218 FSAFS22218 SAFS22220 FSAFS22220 SAFS22222 SAFS22224 SAFS22226 SAFS22228 SAFS22230 SAFS22232 SAFS22234 SAFS22236 SAFS22238 SAFS22240 SAFS22244 43 43 50 50 71 71 81 90 127 149 175 210 280 305 350 420 590 SAFS22515 FSAFS22515 SAFS22516 FSAFS22516 SAFS22517 FSAFS22517 SAFS22518 FSAF22518 SAFS22520 FSAFS22520 SAFS22522 SAFS22524 SAFS22526 SAFS22528 SAFS22530 SAFS22532 SAFS22534 SAFS22536 SAFS22538 SAFS22540 SAFS22544 30 30 37 37 40 40 49 49 65 65 81 94 137 159 189 225 300 330 375 445 615 SAFS-500 ADAPTER MOUNTING S-1 IN. 2 7/16 2 7/16 2 11/16 2 11/16 2 15/16 2 15/16 3 3/16 3 3/16 3 7/16 3 7/16 3 15/16 4 3/16 4 7/16 4 15/16 5 3/16 5 7/16 5 15/16 6 7/16 6 15/16 7 3/16 7 15/16 SAFS515* FSAFS515 SAFS516* FSAFS516 SAFS517* FSAFS517 SAFS518* FSAFS518 SAFS520* FSAFS520 SAFS522 SAFS524 SAFS526 SAFS528 SAFS530 SAFS532 SAFS534 SAFS536 SAFS538 SAFS540 SAFS544 SR-15-0 SR-15-0 SR-16-13 SR-16-13 SR-17-14 SR-17-14 SR-18-15 SR-18-15 SR-20-17 SR-20-17 SR-22-19 SR-24-20 SR-26-0 SR-28-0 SR-30-0 SR-32-0 SR-34-0 SR-36-30 SR-38-32 SR-40-34 SR-44-34 2 REQUIRED ADAPTER NO. LER37 LER37 LER44 LER44 LER53 LER53 LER69 LER69 LER102 LER102 LER109 LER113 LER117 LER122 LER125 LER130 LER140 LER148 LER155 LER159 LER167 SNW-15 SNW-15 SNW-16 SNW-16 SNW-17 SNW-17 SNW-18 SNW-18 SNW-20 SNW-20 SNW-22 SNW-24 SNW-26 SNW-28 SNW-30 SNW-32 SNW-34 SNW-36 SNW-38 SNW-40 SNW-44 NOTES: Triple seal rings (LER series) and stabilizing ring (SR series) are included with the pillow block. Stabilizing ring used only for “fixed” mounting, not used for “free” mounting. * Pillow blocks with 2-hole mounting base, all others have 4-hole mounting base. PILLOW BLOCKS 52 SAFS 200 AND 500 SERIES CAST STEEL PILLOW BLOCKS STRAIGHT BORE MOUNTING and TAPERED BORE/ADAPTER MOUNTING SAFS-200 SERIES STRAIGHT BORE MOUNTING PILLOW BLOCK HOUSING ONLY BASE BOLTS REQUIRED A B C D MAX. SAFS217* FSAFS217 SAFS218* FSAFS218 SAFS220* FSAFS220 SAFS222 SAFS224 SAFS226 SAFS228 SAFS230 SAFS232 SAFS234 SAFS236 SAFS238 SAFS240 SAFS244 3 3/4 3 3/4 4 4 4 1/2 4 1/2 4 15/16 5 1/4 6 6 6 5/16 6 11/16 7 1/16 7 1/2 7 7/8 8 1/4 9 1/2 13 13 13 13 15 15 16 16 18 20 21 22 24 26 28 29 32 3/4 3/4 1/4 1/4 1/2 1/2 3/8 1/8 1/4 3/4 3/4 1/2 3/4 3 3 3 3 4 4 4 4 5 5 6 6 6 7 7 8 8 1/2 1/2 7/8 7/8 3/8 3/8 3/4 3/4 1/8 7/8 1/4 1/4 3/4 1/8 1/2 3/4 F E 1 3/16 1 3/16 1 5/16 1 5/16 1 3/4 1 3/4 1 29/32 2 1/8 2 9/32 2 13/32 2 13/32 2 5/8 2 3/4 3 3 1/8 3 3/8 3 3/4 11 11 11 11 13 13 14 14 16 17 18 19 21 23 24 25 27 1 1/8 1 1/8 1 1/4 1 1/4 1 3/16 1 3/16 1 5/16 1 5/16 1 3/4 1 3/4 1 29/32 2 1/8 2 9/32 2 13/32 2 13/32 2 5/8 2 3/4 3 3 1/8 3 3/8 3 3/4 H L NO. SIZE MIN. 7/8 9 7/8 9 7/8 10 3/8 10 3/8 11 5/8 11 5/8 12 5/8 13 1/4 14 5/8 16 17 17 3/8 19 3/8 20 7/8 21 5/8 22 1/2 24 3/4 --2 1/8 --2 1/8 --2 3/8 2 3/4 2 3/4 3 1/4 3 3/8 3 3/4 3 3/4 4 1/4 4 5/8 4 1/2 5 5 1/4 7 3/8 7 3/8 7 3/4 7 3/4 8 11/16 8 11/16 9 5/8 10 1/4 11 1/2 11 3/4 12 1/2 13 5/16 14 3/16 14 7/8 15 11/16 17 3/16 19 5/8 4 15/16 4 15/16 5 5/8 5 5/8 5 7/8 5 7/8 6 1/4 7 1/8 7 3/4 7 3/8 8 1/8 8 1/2 9 3/8 10 10 1/2 11 11 5/8 2 4 2 4 2 4 4 4 4 4 4 4 4 4 4 4 4 9 5/8 9 5/8 11 11 11 11 11 5/8 11 5/8 13 1/8 13 1/8 14 1/2 14 1/2 16 17 1/8 18 1/4 19 1/4 21 5/8 23 5/8 24 3/8 25 27 7/8 8 5/8 8 5/8 9 5/8 9 5/8 9 7/8 9 7/8 10 3/8 10 3/8 11 5/8 11 5/8 12 5/8 13 1/4 14 5/8 16 17 17 3/8 19 3/8 20 7/8 21 5/8 22 1/2 24 3/4 --1 7/8 --2 1/8 --2 1/8 --2 1/8 --2 3/8 2 3/4 2 3/4 3 1/4 3 3/8 3 3/4 3 3/4 4 1/4 4 5/8 4 1/2 5 5 1/4 6 3/8 6 3/8 6 7/8 6 7/8 7 3/8 7 3/8 7 3/4 7 3/4 8 11/16 8 11/16 9 5/8 10 1/4 11 1/2 11 3/4 12 1/2 13 5/16 14 3/16 14 7/8 15 11/16 16 1/2 18 5/8 4 11/16 4 11/16 4 53/64 4 53/64 4 13/16 4 13/16 5 5/8 5 5/8 5 7/8 5 7/8 6 1/4 7 1/8 7 1/2 7 3/8 8 1/8 8 1/2 9 3/8 10 10 1/2 11 11 5/8 2 4 2 4 2 4 2 4 2 4 4 4 4 4 4 4 4 4 4 4 4 5/8 5/8 1/8 1/8 1/2 1/2 1/8 1/4 1/4 5/8 5/8 3/8 3/4 5/8 3/4 5/8 7/8 3/4 3/4 3/4 7/8 1 1 1 1 1 1 1/4 1 1/4 1 1/2 SAFS-500 ADAPTER MOUNTING SAFS515* FSAFS515 SAFS516* FSAFS516 SAFS517* FSAFS517 SAFS518* FSAFS518 SAFS520* FSAFS520 SAFS522 SAFS524 SAFS526 SAFS528 SAFS530 SAFS532 SAFS534 SAFS536 SAFS538 SAFS540 SAFS544 3 1/8 3 1/8 3 1/2 3 1/2 3 7/8 3 7/8 4 4 4 1/2 4 1/2 4 15/16 5 1/4 6 6 6 5/16 6 11/16 7 1/16 7 1/2 7 1/8 8 1/4 9 1/2 11 11 13 13 13 13 13 13 15 15 16 16 18 20 21 22 24 26 28 29 32 1/4 1/4 3/4 3/4 1/4 1/4 1/2 1/2 3/8 1/8 1/4 3/4 3/4 1/2 3/4 3 3 3 3 3 3 3 3 4 4 4 4 5 5 6 6 6 7 7 8 8 1/8 1/8 1/2 1/2 1/2 1/2 7/8 7/8 3/8 3/8 3/4 3/4 1/8 7/8 1/4 1/4 3/4 1/8 1/2 3/4 5/8 1/2 3/4 5/8 3/4 5/8 7/8 3/4 3/4 3/4 7/8 1 1 1 1 1 1 1 1 1/4 1 1/4 1 1/2 PILLOW BLOCKS 53 54 55 MS-1722 SERIES LOCKNUT DIMENSIONS MILITARY STANDARD LOCKNUT DIMENSIONS LOCKNUT NO. THREADS MAJOR DIA. NO. PER INCH MIN. MS172236 MS172237 MS172238 MS172239 MS172259 MS172241 MS172242 MS172243 MS172244 MS172245 MS172246 MS172247 MS172248 MS172249 MS172250 MS172251 MS172252 MS172253 MS172254 MS172255 MS172256 MS172257 MS172258 0.391 0.469 0.586 0.664 0.781 0.969 1.173 1.376 1.563 1.767 1.967 2.157 2.360 2.548 2.751 2.933 3.137 3.340 3.527 3.730 3.918 4.122 4.325 32 32 32 32 32 32 18 18 18 18 18 18 18 18 18 12 12 12 12 12 12 12 12 OUTSIDE NUT FACE SLOT SLOT APP. WT. DIA. WIDTH DIA. DEPTH WIDTH (LB.) A B C D F MIN. MAX. MIN. MAX. MIN. MAX. MIN. MAX. MIN. MAX. 0.704 0.797 0.923 1.407 1.173 1.360 1.673 1.891 2.079 2.297 2.485 2.735 2.923 3.110 3.329 3.673 3.891 4.110 4.297 4.516 4.704 4.891 5.110 0.724 0.817 0.943 1.067 1.193 1.380 1.693 1.911 2.099 2.317 2.505 2.755 2.943 3.130 3.349 3.693 3.911 4.130 4.317 4.536 4.724 4.911 5.130 0.173 0.173 0.209 0.209 0.240 0.240 0.271 0.271 0.271 0.302 0.302 0.302 0.334 0.334 0.334 0.365 0.365 0.365 0.365 0.396 0.396 0.396 0.396 0.193 0.193 0.229 0.229 0.260 0.260 0.291 0.291 0.291 0.322 0.322 0.322 0.354 0.354 0.354 0.385 0.385 0.385 0.385 0.416 0.416 0.416 0.416 0.511 0.605 0.730 0.855 0.980 1.168 1.418 1.636 1.824 2.042 2.230 2.480 2.668 2.855 3.074 3.355 3.574 3.792 3.980 4.199 4.386 4.574 4.792 0.531 0.625 0.750 0.875 1.000 1.188 1.438 1.656 1.844 2.062 2.250 2.500 2.688 2.875 3.094 3.375 3.594 3.812 4.000 4.219 4.406 4.594 4.812 0.584 0.678 0.802 0.928 1.052 1.240 1.490 1.709 1.896 2.115 2.302 2.552 2.740 2.928 3.146 3.428 3.646 3.865 4.052 4.271 4.459 4.646 4.865 0.604 0.698 0.822 0.948 1.072 1.260 1.510 1.729 1.916 2.135 2.322 2.572 2.760 2.948 3.166 3.448 3.666 3.885 4.072 4.291 4.479 4.666 4.885 0.115 0.115 0.115 0.115 0.178 0.178 0.178 0.178 0.240 0.240 0.240 0.240 0.240 0.240 0.240 0.365 0.365 0.365 0.365 0.365 0.365 0.490 0.490 0.135 0.135 0.135 0.135 0.198 0.198 0.198 0.198 0.260 0.260 0.260 0.260 0.260 0.260 0.260 0.385 0.385 0.385 0.385 0.385 0.385 0.510 0.510 MS-1722 SERIES LOCKNUTS 56 0.010 0.014 0.021 0.028 0.036 0.045 0.055 0.067 0.074 0.134 0.144 0.180 0.211 0.224 0.232 0.371 0.405 0.440 0.464 0.546 0.572 0.577 0.620 MS-1722 SERIES LOCKWASHER DIMENSIONS MILITARY STANDARD LOCKWASHER DIMENSIONS LOCKWASHER BORE NO. KEY FACE DIA. OVER KEY TANG WIDTH TANGS D +.000/-.030 PROJECTION WIDTH F G MIN. MAX. MIN. MAX. 0.828 0.922 1.094 1.203 1.344 1.562 1.859 2.078 2.250 2.500 2.688 2.953 3.188 3.375 3.594 3.922 4.141 4.359 4.547 4.812 5.000 5.188 5.406 1.375 0.062 0.062 0.062 0.062 0.062 0.094 0.094 0.094 0.094 0.125 0.125 0.125 0.125 0.125 0.188 0.188 0.188 0.188 0.188 0.188 0.250 0.250 0.250 0.062 0.094 0.094 0.094 0.094 0.094 0.125 0.125 0.125 0.125 0.156 0.156 0.156 0.156 0.156 0.250 0.250 0.250 0.250 0.250 0.250 0.312 0.312 0.312 0.094 0.084 0.084 0.084 0.084 0.146 0.146 0.146 0.146 0.204 0.204 0.204 0.204 0.204 0.204 0.204 0.297 0.297 0.297 0.297 0.297 0.297 0.360 0.360 0.146 0.104 0.104 0.104 0.104 0.166 0.166 0.166 0.166 0.234 0.234 0.234 0.234 0.234 0.234 0.234 0.327 0.327 0.327 0.327 0.327 0.327 0.390 0.390 0.166 MIN. MAX. MIN. MAX. DIA. C +.020/-.000 0.406 0.484 0.601 0.679 0.801 0.989 1.193 1.396 1.583 1.792 1.992 2.182 2.400 2.588 2.791 2.973 3.177 3.395 3.582 3.800 3.988 4.192 4.395 0.801 0.421 0.499 0.616 0.694 0.816 1.009 1.213 1.416 1.603 1.817 2.017 2.207 2.425 2.613 2.816 3.003 3.207 3.425 3.612 3.830 4.018 4.222 4.425 0.816 0.110 0.110 0.110 0.110 0.156 0.156 0.156 0.156 0.280 0.280 0.280 0.280 0.280 0.280 0.280 0.280 0.340 0.340 0.340 0.340 0.340 0.340 0.340 0.156 0.120 0.120 0.120 0.120 0.176 0.176 0.176 0.176 0.300 0.300 0.300 0.300 0.300 0.300 0.300 0.300 0.360 0.360 0.360 0.360 0.360 0.360 0.360 0.176 0.531 0.625 0.750 0.875 0.969 1.188 1.438 1.656 1.844 2.062 2.250 2.500 2.688 2.875 3.094 3.375 3.594 3.812 4.000 4.219 4.406 4.594 4.812 1.000 A MS172201 MS172202 MS172203 MS172204 MS172205 MS172206 MS172207 MS172208 MS172209 MS172210 MS172211 MS172212 MS172213 MS172214 MS172215 MS172216 MS172217 MS172218 MS172219 MS172220 MS172221 MS172222 MS172223 MS172224 B RADIUS THICKNESS H 0.016 0.016 0.016 0.016 0.016 0.016 0.031 0.031 0.031 0.031 0.031 0.031 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.016 J MIN. MAX. 0.036 0.036 0.036 0.036 0.036 0.046 0.046 0.046 0.058 0.058 0.058 0.058 0.058 0.058 0.058 0.058 0.058 0.058 0.058 0.058 0.058 0.058 0.058 0.036 0.044 0.044 0.044 0.044 0.044 0.054 0.054 0.054 0.068 0.068 0.068 0.068 0.068 0.068 0.068 0.068 0.068 0.068 0.068 0.068 0.068 0.068 0.068 0.044 INSIDE NO. OF APP. WT. DIMENSION TANGS K L +.020/-.000 0.333 0.411 0.513 0.591 0.724 0.880 1.084 1.287 1.474 1.693 1.880 2.067 2.255 2.443 2.631 2.813 3.017 3.220 3.380 3.579 3.786 4.071 4.193 0.724 9 9 11 11 11 13 13 15 15 17 17 17 17 19 19 19 19 19 19 19 19 19 19 11 (LB.) 0.003 0.004 0.005 0.006 0.008 0.013 0.016 0.019 0.030 0.037 0.037 0.042 0.044 0.048 0.052 0.077 0.081 0.084 0.086 0.092 0.094 0.104 0.108 0.009 MS-1722 LOCKWASHERS 57 MS-19067 SERIES LOCKNUT DIMENSIONS MILITARY STANDARD LOCKNUT DIMENSIONS LOCKNUT NUT OUTSIDE FACE INSIDE SLOT SLOT SLOT NO. WIDTH D DIA. C DIA. E CHAMFER J DIA. F WIDTH G RAD. R MS 19067-A00 MS 19067-A01 MS 19067-A02 MS 19067-A03 MS 19067-A04 MS 19067-A05 MS 19067-A06 MS 19067-A07 MS 19067-A08 MS 19067-A09 MS 19067-A10 MS 19067-A11 MS 19067-A12 MS 19067-A13 MS 19067-A14 MS 19067-A15 MS 19067-A16 MS 19067-A17 MS 19067-A18 MS 19067-A19 MS 19067-A20 MS 19067-A21 MS 19067-A22 0.188 0.188 0.219 0.219 0.250 0.250 0.281 0.281 0.281 0.312 0.312 0.312 0.344 0.344 0.344 0.375 0.375 0.375 0.375 0.406 0.406 0.406 0.406 0.031 0.031 0.031 0.031 0.031 0.031 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.078 0.078 0.078 0.078 0.078 0.078 0.078 0.078 0.594 0.688 0.812 0.938 1.031 1.250 1.500 1.719 1.906 2.125 2.312 2.562 2.750 2.937 3.156 3.438 3.656 3.875 4.062 4.281 4.469 4.656 4.875 0.125 0.125 0.125 0.125 0.188 0.188 0.188 0.188 0.250 0.250 0.250 0.250 0.250 0.250 0.250 0.375 0.375 0.375 0.375 0.375 0.375 0.500 0.500 0.010 0.010 0.010 0.010 0.015 0.015 0.015 0.015 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.025 0.025 0.025 0.025 0.025 0.025 0.030 0.030 +.005/-.015 +.000/-.020 0.719 0.812 0.938 1.062 1.156 1.375 1.688 1.906 2.094 2.312 2.500 2.750 2.938 3.125 3.344 3.688 3.906 4.125 4.312 4.531 4.719 4.906 5.125 0.531 0.625 0.750 0.875 0.969 1.188 1.438 1.656 1.844 2.062 2.250 2.500 2.688 2.875 3.094 3.375 3.594 3.812 4.000 4.219 4.406 4.594 4.812 THREAD DATA MINOR DIA. NO. PER INCH MAX. 32 32 32 32 32 32 18 18 18 18 18 18 18 18 18 12 12 12 12 12 12 12 12 MAJOR DIA. MIN. MAX. MIN. MAX. MIN. 0.357 0.435 0.552 0.630 0.747 0.935 1.113 1.316 1.503 1.707 1.907 2.097 2.300 2.488 2.691 2.843 3.047 3.250 3.437 3.640 3.828 4.032 4.235 0.361 0.439 0.556 0.634 0.751 0.939 1.119 1.322 1.509 1.713 1.913 2.103 2.306 2.494 2.697 2.852 3.056 3.259 3.446 3.649 3.837 4.041 4.244 0.371 0.449 0.566 0.644 0.761 0.949 1.137 1.340 1.527 1.731 1.931 2.121 2.324 2.512 2.715 2.879 3.083 3.286 3.473 3.676 3.864 4.068 4.271 0.373 0.451 0.569 0.647 0.764 0.952 1.141 1.344 1.531 1.735 1.935 2.126 2.329 2.517 2.720 2.884 3.089 3.293 3.480 3.683 3.871 4.076 4.279 0.391 0.469 0.586 0.664 0.781 0.969 1.173 1.376 1.563 1.767 1.967 2.157 2.360 2.548 2.751 2.933 3.137 3.340 3.527 3.730 3.918 4.122 4.325 MS-19067 SERIES LOCKNUTS 58 PITCH DIA. MS-19069 SERIES LOCKWASHER DIMENSIONS MILITARY STANDARD LOCKWASHER DIMENSIONS LOCKWASHER NO. THICKNESS BORE Q MS 19069-A00 MS 19069-A01 MS 19069-A02 MS 19069-A03 MS 19069-A04 MS 19069-A23 MS 19069-A05 MS 19069-A06 MS 19069-A07 MS 19069-A08 MS 19069-A09 MS 19069-A10 MS 19069-A11 MS 19069-A12 MS 19069-A13 MS 19069-A14 MS 19069-A15 MS 19069-A16 MS 19069-A17 MS 19069-A18 MS 19069-A19 MS 19069-A20 MS 19069-A21 MS 19069-A22 R NOM. TOL. +/- MAX. MIN. 0.042 0.042 0.042 0.042 0.042 0.042 0.050 0.050 0.050 0.058 0.058 0.058 0.063 0.063 0.063 0.063 0.063 0.063 0.063 0.063 0.063 0.063 0.063 0.063 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.005 0.005 0.005 0.005 0.005 0.005 0.005 0.005 0.005 0.005 0.005 0.005 0.005 0.005 0.005 0.421 0.499 0.616 0.694 0.816 0.816 1.009 1.213 1.416 1.603 1.817 2.017 2.207 2.425 2.613 2.816 3.003 3.207 3.425 3.612 3.830 4.018 4.222 4.425 0.406 0.484 0.601 0.679 0.801 0.801 0.989 1.193 1.396 1.583 1.792 1.992 2.182 2.400 2.588 2.791 2.973 3.177 3.395 3.582 3.800 3.988 4.192 4.395 FACE DIA. E B +.020/-.000 +.000/-.030 0.531 0.625 0.750 0.875 0.969 1.000 1.188 1.438 1.656 1.844 2.062 2.250 2.500 2.688 2.875 3.094 3.375 3.594 3.812 4.000 4.219 4.405 4.594 4.812 KEY WIDTH DIA. OVER TANGS 0.828 0.922 1.094 1.203 1.344 1.375 1.562 1.859 2.078 2.250 2.500 2.688 2.953 3.188 3.375 3.594 3.922 4.141 4.359 4.547 4.812 5.000 5.185 5.406 KEY DEPTH S KEY PROJECTION X V NO. OF TANGS MAX. MIN. MAX. MIN. NOM. TOL. +/- r RAD 0.120 0.120 0.120 0.120 0.176 0.120 0.176 0.176 0.176 0.300 0.300 0.300 0.300 0.300 0.300 0.300 0.300 0.360 0.360 0.360 0.360 0.360 0.360 0.360 0.110 0.110 0.110 0.110 0.156 0.110 0.156 0.156 0.156 0.280 0.280 0.280 0.280 0.280 0.280 0.280 0.280 0.340 0.340 0.340 0.340 0.340 0.340 0.340 0.030 0.030 0.030 0.030 0.030 0.030 0.030 0.050 0.050 0.050 0.050 0.050 0.050 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.085 0.085 0.085 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.035 0.035 0.035 0.035 0.035 0.035 0.055 0.055 0.055 0.055 0.055 0.055 0.055 0.055 0.065 0.065 0.065 0.062 0.062 0.062 0.062 0.062 0.062 0.094 0.094 0.094 0.094 0.125 0.125 0.125 0.125 0.125 0.188 0.188 0.188 0.188 0.188 0.188 0.250 0.250 0.250 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.016 0.016 0.016 0.016 0.016 0.016 0.016 0.031 0.031 0.031 0.031 0.031 0.031 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.047 TANG WIDTH T 9 9 11 11 11 11 13 13 15 15 17 17 17 17 19 19 19 19 19 19 19 19 19 19 MAX. MIN. 0.104 0.104 0.104 0.104 0.166 0.166 0.166 0.166 0.166 0.234 0.234 0.234 0.234 0.234 0.234 0.234 0.327 0.327 0.327 0.327 0.327 0.327 0.390 0.390 0.084 0.084 0.084 0.084 0.146 0.146 0.146 0.146 0.146 0.204 0.204 0.204 0.204 0.204 0.204 0.204 0.297 0.297 0.297 0.297 0.297 0.297 0.360 0.360 MS-19069 LOCKWASHERS 59 MS-19068 SERIES LOCKNUT DIMENSIONS MILITARY STANDARD LOCKNUT DIMENSIONS LOCKNUT THICKNESS NO. D MS19068-00 MS19068-01 MS19068-02 MS19068-03 MS19068-04 MS19068-05 MS19068-06 MS19068-065 MS19068-07 MS19068-08 MS19068-09 MS19068-10 MS19068-11 MS19068-12 MS19068-13 MS19068-14 MS19068-15 MS19068-16 MS19068-17 MS19068-18 MS19068-19 MS19068-20 MS19068-21 MS19068-22 MS19068-24 MS19068-26 MS19068-28 MS19068-30 MS19068-32 MS19068-34 MS19068-36 MS19068-38 MS19068-40 OUTSIDE FACE INSIDE SLOT SLOT DIA. DIA. CHAMFER DIA. WIDTH C E J F G MIN. MAX. +.005/-.015 MIN. MAX. 0.209 0.303 0.303 0.334 0.365 0.396 0.396 0.428 0.428 0.428 0.428 0.490 0.490 0.521 0.553 0.553 0.584 0.584 0.615 0.678 0.709 0.735 0.735 0.766 0.798 0.860 0.923 0.954 1.016 1.048 1.079 1.110 1.173 0.229 0.323 0.323 0.354 0.385 0.416 0.416 0.448 0.448 0.448 0.448 0.510 0.510 0.541 0.573 0.573 0.604 0.604 0.635 0.698 0.729 0.760 0.760 0.791 0.823 0.885 0.948 0.979 1.041 1.073 1.104 1.135 1.198 0.750 0.875 1.000 1.125 1.375 1.562 1.750 2.062 2.062 2.250 2.531 2.687 2.968 3.156 3.375 3.625 3.875 4.156 4.406 4.656 4.937 5.187 5.437 5.718 6.125 6.750 7.093 7.687 8.062 8.656 9.062 9.468 9.843 0.605 0.699 0.793 0.918 1.105 1.261 1.480 1.793 1.793 1.980 2.261 2.418 2.636 2.824 3.043 3.283 3.533 3.814 4.001 4.251 4.533 4.783 4.970 5.251 5.658 6.158 6.501 7.033 7.398 7.991 8.335 8.741 9.116 0.625 0.719 0.813 0.938 1.125 1.281 1.500 1.813 1.813 2.000 2.281 2.438 2.656 2.844 3.063 3.313 3.563 3.844 4.031 4.281 4.563 4.813 5.000 5.281 5.688 6.188 6.531 7.063 7.438 8.031 8.375 8.781 9.156 0.031 0.031 0.031 0.031 0.031 0.031 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.078 0.078 0.078 0.078 0.078 0.078 0.078 0.078 0.078 0.078 0.078 0.078 0.094 0.094 0.094 0.094 0.094 SLOT THREAD DATA RADIUS NO. PER INCH MIN. MAX. MAX. 0.625 0.750 0.812 0.937 1.187 1.375 1.562 1.875 1.875 2.062 2.343 2.500 2.718 2.906 3.125 3.375 3.625 3.906 4.093 4.343 4.625 4.875 5.062 5.343 5.750 6.250 6.593 7.125 7.500 8.093 8.437 8.843 9.218 0.120 0.120 0.120 0.120 0.178 0.178 0.178 0.178 0.178 0.240 0.240 0.240 0.240 0.240 0.240 0.240 0.360 0.360 0.360 0.360 0.360 0.360 0.485 0.485 0.485 0.610 0.610 0.610 0.610 0.610 0.735 0.735 0.735 0.130 0.130 0.130 0.130 0.198 0.198 0.198 0.198 0.198 0.260 0.260 0.260 0.260 0.260 0.260 0.260 0.385 0.385 0.385 0.385 0.385 0.385 0.510 0.510 0.510 0.635 0.635 0.635 0.635 0.635 0.760 0.760 0.760 0.010 0.010 0.010 0.010 0.015 0.015 0.015 0.015 0.015 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.025 0.025 0.025 0.025 0.025 0.025 0.030 0.030 0.030 0.030 0.030 0.030 0.030 0.030 0.030 0.030 0.030 32 32 32 32 32 32 18 18 18 18 18 18 18 18 18 18 12 12 12 12 12 12 12 12 12 12 12 12 8 8 8 8 8 MS-19068 SERIES LOCKNUTS APP. WT. PITCH DIA. MAJOR DIA. (LB./C) R +.010/-.020 60 MINOR DIA. MIN. MAX. MIN. MAX. MIN. 0.357 0.435 0.552 0.630 0.747 0.935 1.113 1.252 1.316 1.503 1.707 1.907 2.097 2.300 2.488 2.691 2.843 3.047 3.250 3.437 3.640 3.828 4.032 4.235 4.626 5.016 5.407 5.798 6.149 6.524 6.931 7.337 7.712 0.361 0.439 0.556 0.634 0.751 0.939 1.119 1.258 1.322 1.509 1.713 1.913 2.103 2.306 2.494 2.697 2.852 3.056 3.259 3.446 3.649 3.837 4.041 4.244 4.635 5.025 5.416 5.807 6.162 6.537 6.944 7.350 7.725 0.371 0.449 0.566 0.644 0.761 0.949 1.137 1.276 1.340 1.527 1.731 1.931 2.121 2.324 2.512 2.715 2.879 3.083 3.286 3.473 3.676 3.864 4.068 4.271 4.662 5.052 5.443 5.834 6.203 6.578 6.985 7.391 7.766 0.373 0.451 0.569 0.647 0.764 0.952 1.141 1.280 1.344 1.531 1.735 1.935 2.126 2.329 2.517 2.720 2.884 3.089 3.292 3.480 3.683 3.871 4.076 4.279 4.670 5.060 5.451 5.842 6.212 6.587 6.994 7.400 7.777 0.391 0.469 0.586 0.664 0.781 0.969 1.173 1.313 1.376 1.563 1.767 1.967 2.157 2.360 2.548 2.751 2.933 3.137 3.340 3.527 3.730 3.918 4.122 4.325 4.716 5.106 5.497 5.888 6.284 6.659 7.066 7.472 7.847 2.0 3.3 3.5 5.3 9.0 11.5 13.0 21.0 22.5 29.0 34.0 42.0 47.0 55.0 63.8 78.8 92.5 104.0 130.0 153.8 178.8 193.8 223.0 255.0 317.0 355.0 475.0 525.0 662.5 665.0 775.0 850.0 1,050.0 MS-19070 SERIES LOCKWASHER DIMENSIONS MILITARY STANDARD LOCKWASHER DIMENSIONS LOCKWASHER THICKNESS BORE FACE DIA. OVER KEY KEY KEY SLOT NO. OF TANG DIA. TANGS WIDTH DEPTH PROJECTION RADIUS TANGS WIDTH V r NO. Q MS19070-00 MS19070-01 MS19070-02 MS19070-03 MS19070-04 MS19070-05 MS19070-06 MS19070-065 MS19070-07 MS19070-08 MS19070-09 MS19070-10 MS19070-11 MS19070-12 MS19070-13 MS19070-14 MS19070-15 MS19070-16 MS19070-17 MS19070-18 MS19070-19 MS19070-20 MS19070-21 MS19070-22 MS19070-24 MS19070-26 MS19070-28 MS19070-30 MS19070-32 MS19070-34 MS19070-36 MS19070-38 MS19070-40 R E B S X NOM. TOL +/- MAX. MIN. MIN. TOL + MAX. MAX. MIN. MAX. MIN. MIN. TOL+ 0.042 0.042 0.042 0.042 0.042 0.050 0.050 0.050 0.050 0.058 0.058 0.058 0.063 0.063 0.063 0.063 0.072 0.072 0.072 0.094 0.094 0.094 0.094 0.125 0.125 0.125 0.125 0.156 0.156 0.156 0.156 0.156 0.156 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.004 0.005 0.005 0.005 0.005 0.005 0.005 0.005 0.005 0.005 0.005 0.006 0.006 0.006 0.006 0.007 0.007 0.007 0.007 0.008 0.008 0.008 0.008 0.008 0.008 0.421 0.499 0.616 0.694 0.816 1.009 1.213 1.353 1.416 1.603 1.817 2.017 2.207 2.425 2.613 2.816 3.003 3.207 3.425 3.612 3.830 4.018 4.222 4.425 4.831 5.226 5.617 6.018 6.424 6.799 7.206 7.612 8.017 0.406 0.484 0.601 0.679 0.801 0.989 1.193 1.333 1.396 1.583 1.792 1.992 2.182 2.400 2.588 2.791 2.973 3.177 3.395 3.582 3.800 3.988 4.192 4.395 4.801 5.191 5.582 5.983 6.389 6.764 7.171 7.577 7.982 0.625 0.719 0.812 0.938 1.125 1.281 1.500 1.812 1.812 2.000 2.281 2.438 2.656 2.844 3.062 3.312 3.562 3.844 4.031 4.281 4.562 4.812 5.000 5.281 5.688 6.188 6.531 7.062 7.438 8.031 8.375 8.781 9.156 0.015 0.015 0.015 0.015 0.015 0.015 0.015 0.015 0.015 0.030 0.030 0.030 0.030 0.030 0.030 0.030 0.030 0.030 0.030 0.045 0.045 0.045 0.045 0.045 0.045 0.045 0.045 0.060 0.060 0.060 0.060 0.060 0.060 0.875 1.016 1.156 1.328 1.531 1.719 1.922 2.250 2.250 2.469 2.734 2.922 3.109 3.344 3.578 3.828 4.109 4.375 4.625 4.938 5.219 5.500 5.703 6.062 6.469 7.031 7.438 8.062 8.438 9.062 9.438 9.875 10.312 0.120 0.120 0.120 0.120 0.176 0.176 0.176 0.176 0.176 0.290 0.290 0.290 0.290 0.290 0.290 0.290 0.290 0.353 0.353 0.353 0.353 0.353 0.353 0.353 0.353 0.435 0.590 0.590 0.590 0.715 0.715 0.715 0.840 0.110 0.110 0.110 0.110 0.156 0.156 0.156 0.156 0.156 0.250 0.250 0.250 0.250 0.250 0.250 0.250 0.250 0.313 0.313 0.313 0.313 0.313 0.313 0.313 0.313 0.375 0.500 0.500 0.500 0.625 0.625 0.625 0.750 0.030 0.030 0.030 0.030 0.030 0.030 0.050 0.050 0.050 0.050 0.050 0.050 0.050 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.070 0.085 0.085 0.085 0.085 0.105 0.105 0.105 0.105 0.105 0.105 0.105 0.105 0.020 0.020 0.020 0.020 0.020 0.020 0.035 0.035 0.035 0.035 0.035 0.035 0.035 0.055 0.055 0.055 0.055 0.055 0.055 0.055 0.055 0.065 0.065 0.065 0.065 0.085 0.085 0.085 0.085 0.085 0.085 0.085 0.085 0.062 0.062 0.062 0.062 0.062 0.094 0.094 0.094 0.094 0.094 0.125 0.125 0.125 0.125 0.125 0.188 0.188 0.188 0.188 0.188 0.188 0.250 0.250 0.250 0.250 0.250 0.250 0.312 0.312 0.312 0.312 0.312 0.312 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.016 0.016 0.016 0.016 0.016 0.016 0.031 0.031 0.031 0.031 0.031 0.031 0.031 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.047 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 T 9 9 11 11 11 13 13 15 15 15 17 17 17 17 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 NOM. TOL +/- 0.115 0.115 0.115 0.115 0.156 0.156 0.156 0.156 0.156 0.219 0.219 0.219 0.219 0.219 0.219 0.219 0.313 0.313 0.313 0.313 0.313 0.313 0.375 0.375 0.375 0.500 0.500 0.500 0.500 0.500 0.625 0.625 0.625 0.005 0.005 0.005 0.005 0.010 0.010 0.010 0.010 0.010 0.015 0.015 0.015 0.015 0.015 0.015 0.015 0.015 0.015 0.015 0.015 0.015 0.015 0.015 0.015 0.015 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.020 MS-19070 LOCKWASHERS 61 62 63 SPANNER WRENCHES ADJUSTABLE SPANNER WRENCHES For standard locknut series ADJUSTABLE SPANNER WRENCH SIZES WRENCH NUMBER FITS LOCKNUT SIZE FOR DIAMETER WRENCH OAL ASW00-06 N00-N06 0.750-2.000 6.375 ASW04-11 N04-N11 1.250-3.000 8.125 ASW08-18 N08-AN18 2.000-4.750 11.375 ASW18-24 AN18-AN24 4.500-6.250 12.125 ASW26-34 AN26-AN34 6.125-8.750 13.750 FIXED SPANNER WRENCHES For standard locknut series SPANNER WRENCH DIMENSIONS PART NO. OUTSIDE SHAFT SHAFT EXT. DIA. NOM. EXT. LENGTH DRIVE SQ. RECESS DRIVE A B C D E +/-.015 MIN. MIN. +.005/+.020 MIN. OAL ID DEPTH F V +/-0.03 DRIVER DRIVER DRIVER SPAN HEIGHT WIDTH W Y Z +.010/-.000 +.015/-.005 SW-00 1 1/4 3/8 2 1/16 3/8 3/16 3/8 2 3/4 .760-.790 0.670 1/8 .107-.117 SW-01 1 3/8 7/16 2 1/8 3/8 1/4 3/8 2 7/8 .885-.915 0.795 3/16 .107-.117 SW-02 1 1/2 9/16 2 1/8 3/8 1/4 3/8 2 7/8 1.010-1.040 0.860 3/16 .107-.117 SW-03 1 5/8 5/8 2 1/8 3/8 5/16 3/8 3 1.135-1.165 0.983 5/32 .107-.117 SW-04 1 7/8 3/4 2 1/16 3/8 5/16 3/8 3 1.385-1.415 1.252 1/4 .165-.175 SW-05 2 1/16 15/16 2 1/16 3/8 3/8 3/8 3 1.572-1.602 1.440 1/4 .165-.175 SW-06 2 3/8 13/16 2 1/4 1/2 3/8 1/2 3 1/4 1.760-1.790 1.627 1/4 .165-.175 SW-07 2 11/16 13/8 2 1/4 1/2 13/32 1/2 3 1/4 2.072-2.102 1.940 1/4 .165-.175 SW-08 2 7/8 19/16 2 1/4 1/2 13/32 1/2 3 1/4 2.260-2.290 2.137 1/4 .227-.237 SW-09 3 3/16 13/4 2 1/4 1/2 13/32 1/2 3 1/4 2.541-2.571 2.419 1/4 .227-.237 SW-10 3 3/8 115/16 2 5/8 1/2 15/32 1/2 3 3/4 2.698-2.728 2.575 3/8 .227-.237 SW-11 3 5/8 21/8 2 5/8 1/2 15/32 1/2 3 3/4 2.979-3.009 2.794 3/8 .227-.237 SW-12 3 13/16 25/16 2 5/8 1/2 1/2 1/2 3 3/4 3.166-3.196 2.981 3/8 .227-.237 SW-13 4 21/2 2 5/8 1/2 1/2 1/2 3 3/4 3.385-3.415 3.200 3/8 .227-.237 SW-14 4 1/4 23/4 2 5/8 1/2 1/2 1/2 3 3/4 3.635-3.665 3.450 3/8 .227-.237 SW-15 4 1/2 27/8 2 3/4 3/4 9/16 3/4 4 1/4 3.885-3.915 3.640 7/16 .347-.357 Metric Spanner Wrenches are also available (SWM and ASWM). SPANNER WRENCHES 64 65 DRT SERIES RETHREADING DIE DIMENSIONS RETHREADING DIE DIMENSIONS PART THREAD NO. SIZE DRT00 DRT01 DRT02 DRT03 DRT04 DRT05 DRT06 DRT065 DRT07 DRT08 DRT09 DRT10 DRT11 DRT12 DRT13 DRT14 DRT15 DRT16 DRT17 DRT18 DRT19 DRT20 DRT22 DRT24 DRT26 DRT28 DRT30 .391-32 .469-32 .586-32 .664-32 .781-32 .969-32 1.173-18 1.313-18 1.376-18 1.563-18 1.767-18 1.967-18 2.157-18 2.360-18 2.548-18 2.751-18 2.933-12 3.137-12 3.340-12 3.527-12 3.730-12 3.918-12 4.325-12 4.716-12 5.106-12 5.497-12 5.888-12 SHAFT THREADS PITCH DIA. MAJOR DIA. MINOR DIA. A +0/-0.10 B +0/-0.015 MAX. MIN. MAX. MIN. MAX. 0.088 1.063 1.250 1.438 1.625 1.625 1.813 2.375 2.375 3.125 3.125 3.500 3.500 4.500 4.500 4.500 5.000 5.000 5.000 6.000 6.000 6.000 8.000 8.000 8.000 8.000 8.000 0.438 0.500 0.625 0.625 0.875 0.875 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 0.391 0.469 0.586 0.664 0.781 0.969 1.173 1.313 1.376 1.563 1.767 1.967 2.157 2.360 2.548 2.751 2.933 3.137 3.340 3.527 3.730 3.918 4.325 4.716 5.106 5.497 5.888 0.3870 0.4650 0.5820 0.6600 0.7770 0.9650 1.1680 1.3050 1.3710 1.5580 1.7620 1.9620 2.1520 2.3550 2.5430 2.7460 2.9270 3.1310 3.3360 3.5210 3.7240 3.9120 4.3190 4.7050 5.0950 5.4860 5.8770 0.3910 0.4487 0.5657 0.6437 0.7607 0.9487 1.1369 1.2764 1.3399 1.5269 1.7309 1.9309 2.1209 2.3239 2.5119 2.7149 2.8789 3.0829 3.2859 3.4729 3.6759 3.8639 4.2709 4.6619 5.0520 5.4429 5.8339 0.3870 0.4461 0.5627 0.6407 0.7573 0.9453 1.1329 1.2724 1.3359 1.5224 1.7264 1.9264 2.1158 2.3188 2.5008 2.7098 2.8735 3.0770 3.2800 3.4655 3.6685 3.8565 4.2626 4.6536 5.0440 5.4346 5.8256 0.3527 0.4307 0.5477 0.6257 0.7427 0.9307 1.1048 1.2443 1.3078 1.4948 1.6988 1.8988 2.0888 2.2918 2.4798 2.6828 2.8308 3.0348 3.2378 3.4248 3.6278 3.8158 4.2228 4.6138 5.0038 5.3948 5.7858 Metric Rethreading Dies are also available (DRTM). DRT SERIES RETHREADING DIES 66 NC SERIES CLAMP NUT DIMENSIONS CLAMP NUT DIMENSIONS CLAMP NUT NO. SIZE NO. PER INCH NC-00 NC-01 NC-02 NC-03 NC-04 NC-05 NC-06 NC-07 NC-08 NC-09 NC-10 NC-11 NC-12 NC-13 NC-14 0.391 0.469 0.586 0.664 0.781 0.969 1.173 1.376 1.563 1.767 1.967 2.157 2.360 2.548 2.751 32 32 32 32 32 32 18 18 18 18 18 18 18 18 18 THREADS MINOR DIA. PITCH DIA. MIN. MAX. MIN. MAX. 0.3572 0.4352 0.5522 0.6302 0.7472 0.9352 1.1129 1.3159 1.5029 1.7069 1.9069 2.0969 2.2999 2.4879 2.6909 0.3606 0.4386 0.5556 0.6336 0.7506 0.9386 1.1189 1.3219 1.5089 1.7129 1.9129 2.1029 2.3059 2.4939 2.6969 0.3707 0.4487 0.5657 0.6437 0.7607 0.9487 1.1369 1.3399 1.5263 1.7309 1.9309 2.1209 2.3239 2.5119 2.7149 0.3733 0.4513 0.5687 0.6467 0.7641 0.9521 1.1409 1.3439 1.5308 1.7354 1.9354 2.1260 2.3290 2.5170 2.7200 OUTSIDE DIA. C NUT WIDTH D FACE DIA. S 1.000 1.125 1.375 1.562 1.750 2.000 2.125 2.375 2.562 2.688 3.000 3.375 3.625 3.875 4.125 0.375 0.375 0.375 0.438 0.438 0.438 0.500 0.500 0.500 0.510 0.510 0.635 0.635 0.635 0.635 0.625 0.719 0.813 0.938 1.125 1.281 1.500 1.813 2.000 2.280 2.430 2.650 2.840 3.060 3.310 CLAMP SCREW SIZE M3 M3 M4 M5 M5 M5 M5 M5 M5 M6 M6 M8 M8 M8 M8 Metric Clamp Nuts are also available. NC SERIES CLAMP NUTS 67 X WASHERS X-WASHERS and PINS DIMENSIONS X WASHER DIMENSIONS X WASHER ID NO. A B C D E F 0.086 0.098 0.130 0.164 0.190 0.222 0.256 0.285 0.317 0.347 0.381 0.025 0.055 0.055 0.065 0.065 0.075 0.075 0.075 0.089 0.089 0.089 0.320 0.364 0.430 0.523 0.593 0.622 0.698 0.822 0.872 0.948 1.060 0.406 0.490 0.575 0.687 0.745 0.776 0.905 0.986 1.100 1.190 1.297 0.210 0.297 0.359 0.422 0.437 0.469 0.500 0.563 0.609 0.688 0.797 0.406 0.475 0.556 0.665 0.730 0.775 0.890 0.984 1.078 1.188 1.281 +.000/-.005 +.000/-.004 G H I J L 0.086 0.093 0.093 0.125 0.125 0.156 0.156 0.187 0.187 0.218 0.218 0.250 0.250 0.279 0.279 0.311 0.311 0.341 0.341 0.375 0.375 0.156 0.187 0.218 0.250 0.281 0.312 0.343 0.375 0.406 0.437 0.468 0.500 0.531 0.562 0.593 0.625 0.656 0.687 0.718 0.750 0.781 0.250 0.312 0.343 0.375 0.406 0.437 0.468 0.500 0.531 0.562 0.593 0.625 0.656 0.687 0.718 0.750 0.781 0.812 0.843 0.875 0.906 0.031 0.062 0.062 0.062 0.062 0.075 0.075 0.075 0.075 0.083 0.083 0.083 0.083 0.083 0.083 0.097 0.097 0.097 0.097 0.097 0.097 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.093 0.093 0.093 0.093 0.093 0.093 0.093 0.093 9000 5-4 9000 6 9000 8 9000 10 9000 12 9000 14 9000 16 9000 18 9000 20 9000 22 9000 24 THICKNESS PIN DIMENSIONS SIZE H-5 H-6 H-7 H-8 H-9 H-10 H-11 H-12 H-13 H-14 H-15 H-16 H-17 H-18 H-19 H-20 H-21 H-22 H-23 H-24 H-25 +.005/-.000 NOTES: X-WASHERS Commercial tolerances All X-Washers are zinc plated or plated to your specifications PINS When ordering, specify pin part number and effective length “K”. Pins plated to your specifications. Special pin designs quoted at your request. X-WASHERS 68 X TM WA S H E R R E TA I N E R STANDARD’s X‐WASHER provides manufacturing industries with a simple, efficient, economical fastener/retainer assembly. The X‐WASHER func‐ ons as both a fastener and a washer; by virtue of its posi ve clinching opera on, the X‐WASHER is a versa le and strong fastener –in many cases providing sufficient axial strength to replace a nut and washer. The shear‐resistant X‐WASHER is stamped from cold rolled steel* (Spec. SAE 1010 or equiv.) and then cadmium or zinc plated.* STANDARD X‐WASHERS hold produc on costs to a minimum by elimina ng the two– and three‐item assembly required by tradi onal fasteners. Easily applied and quickly clamped to a posi ve 360o closure, the X‐WASHER saves hours of assembly me; simple “one‐two” installa on, combined with STANDARD’s posi ve clinching ac on elimi‐ nate costly produc on failures. The X‐WASHER is applied to the grooved pin by hand and quickly clamped with pliers or automa c equipment. Removal lugs facilitate any necessary service or repairs. “Easy on...Strong posi ve closure…Easy off.” X‐WASHER sizes are readily available for pin diameters from 5/64 to 25/32 inch. *SPECIAL MATERIAL OR PLATING QUOTED ON REQUEST X-WASHERS 69 Contract Machining Highest Quality Machined Products Through our Quality, Engineering, and Manufacturing systems, we at Standard Locknut can produce products to your specific requirements and deliver on time. Our core competency in CNC machining and secondary operations such as broaching, milling, drilling and tapping provide you with the highest quality part you expect through a team of highly skilled and dedicated associates. We are TS16949 and AS9100 certified, so we understand the importance of quality, delivery, and customer satisfaction. Capabili es More than 80 CNC work centers for machining of forgings, castings, tubing, or bar stock CNC Machining (Milling, Drilling, and Threading) of parts in a 50” L x 26” W x 25” H envelope Turning of parts up to 52” in diameter Production capability for low or high production volumes Expedited deliveries available Contact our Sales Department at sales@stdlocknut.com for a quote. Or Call Customer Service at 800‐783‐6887 CONTRACT MACHINING
