2332 Cathy Lane
Thank you for your purchase. Versteel®
Jasper, Indiana
hopes that you have many great years
47546
of use from this table and from all of our
800.876.2120
products. If you have questions that
812.482.9318 Fax
these instructions don’t answer, please
www.versteel.com
call customer service at 800.876.2120.
A S S E M B L Y I N S T R U C T I O N S : TIM MEETING TABLE
DOCUMENT CONTAINS 1 PAGE
COMPONENTS:
A
TABLE TOP (1 QTY)
B
LEG/BASE ASSEMBLY (1 QTY)
C
LATCH ASSEMBLY (1 QTY)
D
3/8”-16 SOCKET SET SCREWS (2 QTY)
E
1/4”-20 SOCKET CAP SCREWS (10 QTY)
F
5/32 HEX KEY (1 QTY)
G
3/16 HEX KEY (1 QTY)
1
2
ASSEMBLY : STEP 1
PLACE THE TABLE TOP UPSIDE DOWN ON THE
FLOOR. (MAKE SURE THE FLOOR IS CLEAN AND
FREE OF ANY DEBRIS.)
ASSEMBLY : STEP 2
PLACE THE LATCH ASSEMBLY INTO THE TOP
WITH THE LOOP OF THE LATCH FACING THE
OUTER EDGE OF THE TABLE. (DIAGRAM 1)
INSERT (4) 1/4”-20 FLAT HEAD SOCKET CAP
SCREWS INTO THE HOLES AND HAND-TIGHTEN
THEM.
ASSEMBLY : STEP 3
AFTER ALL (4) SCREWS HAVE BEEN INSERTED
AND HAND-TIGHTENED, SECURE THEM WITH
THE PROVIDED 5/32 HEX KEY.
HINGE PLATE
3
ASSEMBLY : STEP 4
REMOVE THE PACKING STRAPS AND SPACER
BLOCKS FROM THE LEG/BASE ASSEMBLY AND
DISCARD.
ASSEMBLY : STEP 5
UNFOLD THE BASE AND POSITION IT UPSIDE
DOWN ON THE TOP SO THAT THE (3) HOLES IN
EACH HINGE PLATE LINE UP WITH THE THREADED
INSERTS IN THE TOP. (DIAGRAM 2) INSERT (6)
1/4”-20 FLAT HEAD SOCKET CAP SCREWS INTO
THE HOLES AND HAND-TIGHTEN THEM.
CONT’D
B
A S S E M B L Y I N S T R U C T I O N S : T IM MEETING TABLE
ASSEMBLY : STEP 6
AFTER ALL (6) SCREWS HAVE BEEN INSERTED
AND HAND-TIGHTENED, SECURE THEM WITH
THE 5/32 HEX KEY.
4
ASSEMBLY : STEP 7
ALIGN THE LATCH WITH THE LATCH BLOCK ON
THE LEG/BASE ASSEMBLY. (DIAGRAM 3)
ASSEMBLY : STEP 8
WITH THE 5/32 HEX KEY, REMOVE SET SCREWS
FROM EACH CLEVIS IN THE FRAME. ROTATE
EACH CLEVIS ONE TURN TO POSITION IT WITH
THE HOLE FACING UPWARDS. (DIAGRAM 4)
ASSEMBLY : STEP 9
SLIDE AN EYE HOOK INTO THE SLOT OF A CLEVIS
AND ALIGN THE EYE HOOK AND CLEVIS SO THAT
THE HOLES ARE LINED UP AND THE HOLE IN THE
CLEVIS FACES UPWARDS. YOU MAY NEED TO
ROTATE THE CLEVIS AND/OR THE EYE HOOK 1/2
TURN IN ORDER TO GET THE EYE HOOK INTO
THE SLOT. (DIAGRAM 5)
5
ASSEMBLY : STEP 10
ONCE THE EYE HOOK AND CLEVIS ARE ALIGNED,
INSERT THE SET SCREW THROUGH THE HOLES IN
THE EYE HOOK AND CLEVIS. TIGHTEN WITH THE
PROVIDED 3/16 HEX KEY.
ASSEMBLY : STEP 11
TURN THE TABLE UPRIGHT WHILE LATCHED AND
CYCLE TABLE TO ENSURE PROPER OPERATION.
NOTE: THE TABLE SHOULD CYCLE SMOOTHLY
FROM THE LATCHED USER POSITION TO THE
TILTED TRANSPORT POSITION. IF IT DOES NOT,
CHECK THE ALIGNMENT OF THE LATCH AND
LATCH BLOCK. IN THE EVENT THEY DO NOT
ALIGN, REPEAT STEPS 8 - 11 AND ROTATE THE
EYE HOOK ROD TO LENGTHEN OR SHORTEN IN
ORDER TO ALLOW PROPER LATCH ALIGNMENT.
270.INS.TMM 509