Exam
Name___________________________________
MULTIPLE CHOICE. Choose the one alternative that best completes the statement or answers the question.
1) Technician A says that clicker type torque wrenches should be calibrated regularly. Technician B
says to store clicker torque wrenches at their minimum setting. Which technician is correct?
A) Technician A only
B) Technician B only
C) Both technicians A and B
D) Neither technician A nor B
1)
2) Two technicians are discussing torque wrenches. Technician A says that a torque wrench is capable
of tightening a fastener with more torque than a conventional breaker bar or ratchet. Technician B
says that a torque wrench should be calibrated regularly for the most accurate results. Which
technician is correct?
A) Technician A only
B) Technician B only
C) Both technicians A and B
D) Neither technician A nor B
2)
3) Open end and box end wrenches are offset how many degrees for clearance?
A) 90 degrees
B) 15 degrees
C) 45 degrees
3)
4) Which type tool is designed for cutting only?
A) Diagonal cutters
C) Both A and B
B) Lineman pliers
D) Neither A nor B
5) Crowfoot sockets are available in which design?
A) Flare nut wrench
C) Both A and B
B) Open end wrench
D) Neither A nor B
D) 0 degrees
4)
5)
6) Technician A says that adjustable end wrenches should be used to tighten fasteners. Technician B
says that adjustable end wrenches can round the edges of fasteners. Which technician is correct?
A) Technician A only
B) Technician B only
C) Both technicians A and B
D) Neither technician A nor B
6)
7) When working with hand tools, always ________.
A) Pull a wrench, don't push a wrench
B) Push the wrench, don't pull it toward you
7)
8) Which tool has a replaceable cutting edge?
A) Aviation snips
B) Side cut pliers
C) Utility knife
9) Which type hammer is designed for automotive service use?
A) Ball peen
B) Claw
C) Both A and B
D) Tin snips
D) Neither A nor B
10) Which type torque wrench displays the actual torque applied?
A) Click
B) Beam
C) Both A and B
D) Neither A nor B
11) Which type of Phillips screwdriver has the sharpest tip?
A) #2
B) #1
C) #3
D) None of these
1
8)
9)
10)
11)
12) Which type of pliers is capable of fitting over a large object?
A) Locking pliers
B) Multigroove adjustable pliers
C) Linesman's pliers
D) Slip joint pliers
12)
13) Which type wrench is used on fasteners that do NOT require a lot of torque?
A) Open end
B) Adjustable
C) Box end
13)
D) None of these
14) What type of screwdriver should be used if there is very limited space above the head of the
fastener?
A) Phillips screwdriver
B) Robertson screwdriver
C) Impact screwdriver
D) Offset screwdriver
14)
15) Which tool is most commonly used by automotive service technicians?
A) Wrench
B) Hammer
C) Pliers
D) None of these
15)
16) Slip joint pliers can be used in how many positions?
A) Six
B) One
D) Two
C) Four
17) Refer to the picture below. What is the proper name for this tool?
A) 1/2 open wrench
C) Double wrench
16)
17)
B) Flare nut wrench
D) Combination wrench
TRUE/FALSE. Write 'T' if the statement is true and 'F' if the statement is false.
18) A Torx driver can offer more torque than a Phillips-type driver.
18)
MULTIPLE CHOICE. Choose the one alternative that best completes the statement or answers the question.
19) What type of hammer is plastic coated, has a metal casing inside, and is filled with small lead balls?
A) Plastic hammer
B) Sledge hammer
C) Soft blow hammer
D) Dead blow hammer
19)
20) Which tool listed is a brand name?
A) Side cutters
C) Locking pliers
20)
B) Vise grips
D) Monkey wrench
21) The proper term for Channel Locks is _________.
A) Locking pliers
C) Multigroove adjustable pliers
B) Crescent wrench
D) Vise Grips
2
21)
22) Refer to the picture below. Choose the correct name for the tool.
A) Socket wrench
C) End wrench
22)
B) Flare wrench
D) Combination wrench
23) Refer to the picture below. Identify tool "B".
23)
A) Slip joint pliers
C) Water pump plier
B) Diagonal cutter
D) Needle nose plier
24) Which type socket is more likely to round the corners of a fastener?
A) 6 point
B) 12 point
C) Both A and B
D) Neither A nor B
25) Technician A says that a crowfoot socket can be used with a ratchet. Technician B says that a
crowfoot socket can be used with an extension. Which technician is correct?
A) Technician A only
B) Technician B only
C) Both technicians A and B
D) Neither technician A nor B
3
24)
25)
Answer Key
Testname: MLR HAND TOOLS
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
15)
16)
17)
18)
19)
20)
21)
22)
23)
24)
25)
C
B
B
A
C
B
A
C
A
B
B
B
A
D
A
D
B
TRUE
D
B
C
D
B
B
C
4