Strand Architectural Lighting Controls
Photocell/Daylighting Sensors
The Vision.net Photocell Daylighting Sensor is a low-voltage
daylighting sensor that measures changes in ambient light
and controls its connected lighting loads according to the
user’s programming.
Vision.net Ceiling Photocell / Daylight Harvesting Sensor
PG
The unit is able to decipher minor changes in light levels
(such as passing cloud cover, intermittent shadowing, etc.)
to prevent unwanted or inadvertent light cycling.
M
/
IT
EX
LA
SE
R
FIE
SE
LD
A
LE
C
T
S RO
N
F
SE
ST
F
T
TE
S R
SE C
LY
O
PHMIS
R
N
S
C
E S
LY
IS
R
W
M
TIM
M
E
LD
TO
E
0 I
O
D SW
IM
TIM
FIE
H
O
/1
D
O
#
V
/P
M
TM
R
E
AY
D
/D
O N S
5 O
IM
4
M HO
D
W
V
C
H
I/
D
P
N
R
C
/S
D
C
N
C
0
O
3 D
SC
3
K
/3
D
T
I/
H
Y
N
D AIN
A
S
FA
P
G
P
LM
D
IN
5
TT / 1 T
2
/2
H
A
SE AI
D UN
M
P
F
S
H
0
1
/2
N
H
U
D UN
AO
+S
LS
5
O
-A
/1 T
H N
G
O
L D SU
M
=
O
-M
H N
D U
-S
B
E
F
C
1
G
D
The Vision.net photocell provides a truly effective energy
conservation lighting control system by harvesting daylight,
reducing your energy costs.
H
2
3
5
4
6
D
0
7
LT
AU EF TR
S
M
8
AY S
PL G
IS IN
D TT
SE
9
Ceiling Sensor IR Programming Remote
Features
•
Detects and identifies pre-programmed ambient daylight
levels to turn on lights when needed, and to prevent them
from turning on when the ambient daylight is above a
certain level
•
Upon detection of a pre-programmed daylight set point, the
sensor may be programmed to execute any Vision.net
command across the architectural control network
•
User-friendly programming unit is available to configure the
sensor without the use of ladders
•
“Laser Painting,” a sensor with the laser pointer built into
the remote, provides accurate sensor selection for
programming
•
Sensor can be programmed with a laptop PC as well as
with a remote
•
Status LEDs facilitate sensor programming
•
Each sensor can be programmed to execute any Vision.net
system command
SPECIFICATION SUBMITTAL
CONSULTANT:
PROJECT NAME:
MODEL NUMBER | QUANTITY:
DATE:
PROJECT NUMBER:
APPROVED BY:
Ceiling Photocell Sensors
Strand Architectural Lighting Controls
Vision.net photocell sensors provide energy-saving lighting
controls for your facility. Sensors easily integrate into any
Vision.net architectural control system, providing direct control
of Vision.net compatible dimmers and low-voltage relay
switching systems.
Choices - Application Flexibility
Vision.net photocell sensors can be used as part of an openloop or closed-loop daylighting system.
Open Loop Daylighting Systems
Open loop daylighting systems measure only natural daylight,
and does not sense any electric lighting. The photocell should
not see any electric light and should be mounted near a
window.
Vision.net Ceiling Photocell / Daylight Harvesting Sensor
Closed Loop Daylighting Systems
Closed loop daylighting systems measure the combined light
level from both natural daylight and electric lighting systems.
Ordering Information
Cat No.
Description
Ceiling-Mounted Photocell Sensors
63060CM Vision.net Ceiling Mount Photocell / Daylighting
Sensor, Low Voltage
Sensor IR Programming Remote
63063
Vision.net Ceiling Sensor Infrared Remote
Programmer
Vision.net AV Input / Sensor Interface
63065SE
Vision.net A/V Input / Sensor Interface
Philips Strand Lighting
Dallas
10911 Petal Street
Dallas, Texas 75238
Tel: (214) 647-7880
Fax: (214) 647-8031
New York
267 5th Ave, 4th Floor
New York, NY 10016
Tel: (212) 213-8219
Fax: (212) 532-2593
Auckland
19-21 Kawana Street
Northcote, Auckland 0627
New Zealand
Tel: + 64 9 481 0100
Fax: + 64 9 481 0101
Asia
Room 6-10,
20/F Delta House
3 On Yiu Street
Shatin, N.T. Hong Kong
Tel: + 852-2757-3033
Fax: + 852-2757-1767
012111NA
www.strandlighting.com
© Philips Group 2011
All rights reserved.
The Company reserves the right
to make any variation in design or
construction to the equipment
described. E&OE
Europe
European Service & Distribution Centre
Marssteden 152
Enschede 7547 TD
the Netherlands
Tel: +31-53-4500424
Fax: +31-53-4500425