CLD-DS61 Rev 6F
Product family data sheet
Cree® XLamp® XM-L2 LEDs
Product Description
FEATURES
Table of Contents
The XLamp® XM-L2 LED builds on the
• Available in white, 70‑CRI white,
Characteristics.........................................2
unprecedented
performance
of
the
original XM-L, increasing lumen output
80‑CRI white, 85‑CRI white and
Flux Characteristics.................................3
90‑CRI white
Relative Spectral Power Distribution......5
up to 20% while providing a single die
• ANSI‑compatible chromaticity bins
Relative Flux vs. Junction Temperature.. 5
LED point source for precise optical
• Binned at 85 °C
Electrical Characteristics.........................6
control. The XM-L2 LED shares the same
• Maximum drive current: 3000 mA
Relative Flux vs. Current..........................6
mechanical and optical footprint as the
• Low thermal resistance: 2.5 °C/W
Relative Chromaticity vs. Current............7
original XM-L, providing a seamless
• Wide viewing angle: 125°
Relative Chromaticity vs. Temperature...7
upgrade path and shortened design
• Unlimited floor life at
Typical Spatial Distribution......................8
cycle.
≤ 30 ºC/85% RH
• Reflow solderable - JEDEC
XLamp XM-L2 LEDs are the ideal choice
J‑STD‑020C
Thermal Design........................................8
Reflow Soldering Characteristics............9
Notes......................................................10
for lighting applications where high
• Electrically neutral thermal path
Mechanical Dimensions........................12
light output and maximum efficacy are
• RoHS and REACh compliant
Tape and Reel.........................................13
required, such as LED light bulbs, outdoor
• UL recognized component
Packaging...............................................14
lighting, portable lighting, indoor lighting
®
(E349212)
www.cree.com/Xlamp
and solar-powered lighting.
Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are
registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
XLamp ® XM-L2 LED
Characteristics
Characteristics
Unit
Thermal resistance, junction to solder point
°C/W
2.5
degrees
125
mV/°C
-1.6
Viewing angle (FWHM)
Temperature coefficient of voltage
ESD withstand voltage (HBM per Mil-Std-883D)
Minimum
Typical
Maximum
V
8000
mA
3000
Reverse voltage
V
-5
Forward voltage (@ 700 mA, 85 °C)
V
2.85
Forward voltage (@ 1500 mA, 85 °C)
V
3.05
Forward voltage (@ 3000 mA, 85 °C)
V
3.3
LED junction temperature
°C
DC forward current
3.15
150
Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
2
XLamp ® XM-L2 LED
Flux Characteristics (TJ = 85 °C)
The following table provides several base order codes for XLamp XM-L2 LEDs. It is important to note that the base order codes listed
here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the
order-code nomenclature, please consult the XLamp XM LED Family Binning and Labeling document.
CCT Range
Color
Min.
Cool White
Neutral White
Warm White
70-CRI White
80-CRI White
85-CRI White
5000 K
3700 K
2600 K
3700 K
2600 K
2600 K
Max.
8300 K
5000 K
3700 K
5000 K
4300 K
3200 K
Minimum Luminous Flux (lm)
@ 700 mA
Calculated Minimum Luminous Flux
(lm) @ 85 °C**
Group
Flux (lm) @
85 °C
Flux (lm) @
25 °C*
1000 mA
1500 mA
2000 mA
Order Code
T5
260
296
357
502
631
XMLBWT-00-0000-0000T5051
T6
280
318
385
541
679
XMLBWT-00-0000-0000T6051
U2
300
342
412
580
728
XMLBWT-00-0000-0000U2051
U3
320
364
439
618
776
XMLBWT-00-0000-0000U3051
T4
240
273
330
464
582
XMLBWT-00-0000-000LT40E4
T5
260
296
357
502
631
XMLBWT-00-0000-000LT50E4
T6
280
318
385
541
679
XMLBWT-00-0000-000LT60E4
U2
300
342
412
580
728
XMLBWT-00-0000-000LU20E4
T2
200
227
275
386
485
XMLBWT-00-0000-000LT20E7
T3
220
250
302
425
534
XMLBWT-00-0000-000LT30E7
T4
240
273
330
464
582
XMLBWT-00-0000-000LT40E7
T5
260
296
357
502
631
XMLBWT-00-0000-000LT50E7
T5
260
296
357
502
631
XMLBWT-00-0000-000BT50E3
T6
280
318
385
541
679
XMLBWT-00-0000-000BT60E3
U2
300
342
412
580
728
XMLBWT-00-0000-000BU20E3
U3
320
364
439
618
776
XMLBWT-00-0000-000BU30E3
T2
200
227
275
386
485
XMLBWT-00-0000-000HT20E7
T3
220
250
302
425
534
XMLBWT-00-0000-000HT30E7
T4
240
273
330
464
582
XMLBWT-00-0000-000HT40E7
T5
260
296
357
502
631
XMLBWT-00-0000-000HT50E7
S4
164
186
225
317
398
XMLBWT-00-0000-000PS40E7
S5
172
196
236
332
417
XMLBWT-00-0000-000PS50E7
S6
182
207
250
352
442
XMLBWT-00-0000-000PS60E7
T2
200
227
275
386
485
XMLBWT-00-0000-000PT20E7
Notes:
•
Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
See the Measurements section (page 10).
•
Typical CRI for Cool White (5000 K – 8300 K CCT) is 65.
•
Minimum CRI for 70-CRI White is 70.
•
Typical CRI for Neutral White (3700 K – 5000 K CCT) is 75.
•
Minimum CRI for 80-CRI White is 80.
•
Typical CRI for Warm White (2600 K – 3700 K CCT) is 80.
•
Minimum CRI for 85-CRI White is 85.
•
Minimum CRI for 90-CRI White is 90.
*
Flux values @ 25 °C are calculated and are for reference only.
** Calculated flux values at 1000 mA, 1500 mA and 2000 mA are for reference only.
Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
3
XLamp ® XM-L2 LED
Flux Characteristics (TJ = 85 °C) - Continued
CCT Range
Color
Min.
90-CRI White
2600 K
Max.
3200 K
Minimum Luminous Flux (lm)
@ 700 mA
Calculated Minimum Luminous Flux
(lm) @ 85 °C**
Order Code
Group
Flux (lm) @
85 °C
Flux (lm) @
25 °C*
1000 mA
1500 mA
2000 mA
S4
164
186
225
317
398
XMLBWT-00-0000-000US40E7
S5
172
196
236
332
417
XMLBWT-00-0000-000US50E7
S6
182
207
250
352
442
XMLBWT-00-0000-000US60E7
T2
200
227
275
386
485
XMLBWT-00-0000-000UT20E7
Notes:
•
Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
See the Measurements section (page 10).
•
Typical CRI for Cool White (5000 K – 8300 K CCT) is 65.
•
Minimum CRI for 70-CRI White is 70.
•
Typical CRI for Neutral White (3700 K – 5000 K CCT) is 75.
•
Minimum CRI for 80-CRI White is 80.
•
Typical CRI for Warm White (2600 K – 3700 K CCT) is 80.
•
Minimum CRI for 85-CRI White is 85.
•
Minimum CRI for 90-CRI White is 90.
*
Flux values @ 25 °C are calculated and are for reference only.
** Calculated flux values at 1000 mA, 1500 mA and 2000 mA are for reference only.
Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
4
XLamp ® XM-L2 LED
Relative Spectral Power
Relative Spectral Power Distribution
Relative Radiant Power (%)
100
80
60
5000 K - 8300 K CCT
3700 K - 5000 K CCT
2600 K - 3700 K CCT
40
20
0
380
430
480
530
580
630
680
730
780
Wavelength (nm)
Relative Flux Output vs. Junction Temperature
Relative Flux vs. Junction Temperature (IF = 700 mA)
120
Relative Luminous Flux (%)
100
80
60
40
20
0
25
50
75
100
125
150
Junction Temperature (ºC)
Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
5
XLamp ® XM-L2 LED
Electrical Characteristics (Tj = 85°C)
Electrical Characteristics (TJ = 85 °C)
3000
2800
2600
Forward Current (mA)
2400
2200
2000
1800
1600
1400
1200
1000
800
600
400
200
0
2.6
2.8
3.0
3.2
3.4
Forward Voltage (V)
Relative Intensity vs. Current (Tj
= 85°C)
Relative Flux vs. Current (TJ = 85 °C)
350
Relative Luminous Flux (%)
300
250
200
150
100
50
0
0
200
400
600
800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000
Forward Current (mA)
Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
6
XLamp ® XM-L2 LED
Relative Chromaticity Vs. Current, WW
Relative Chromaticity vs. Current (Warm White)
0.012
0.008
0.004
ΔCCx
0.000
ΔCCy
-0.004
-0.008
-0.012
0
500
1000
1500
2000
2500
3000
Current (mA)
Relative Chromaticity Vs. Temperature WW
Relative Chromaticity vs. Temperature (Warm White)
0.012
0.008
0.004
ΔCCx
0.000
ΔCCy
-0.004
-0.008
-0.012
25
50
75
100
125
150
Tsp (°C)
Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
7
XLamp ® XM-L2 LED
Typical Spatial Radiation Pattern
Typical Spatial Distribution
Relative Luminous Intensity (%)
100
80
60
40
20
-90
-70
-50
-30
-10
0
10
30
50
70
90
Angle (º)
Thermal Design
The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end
Thermal
Design
Coolproduct
White to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life
and optical characteristics.
3500
Maximum Current (mA)
3000
2500
2000
1500
Rj-a = 4°C/W
1000
Rj-a = 7°C/W
Rj-a = 10°C/W
500
0
Rj-a = 15°C/W
0
20
40
60
80
100
120
140
160
Ambient Temperature (ºC)
Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
8
XLamp ® XM-L2 LED
Reflow Soldering Characteristics
In testing, Cree has found XLamp XM-L2 LEDs to be compatible with JEDEC J‑STD‑020C, using the parameters listed below. As a general
guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of the solder paste used.
Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment.
tP
TP
Critical Zone
TL to TP
Temperature
Ramp-up
TL
tS
Tsmax
Tsmin
Ramp-down
ts
Preheat
25
t 25˚C to Peak
Profile Feature
Average Ramp-Up Rate (Tsmax to Tp)
IPC/JEDEC J-STD-020C
Time
Lead-Free Solder
1.2 °C/second
Preheat: Temperature Min (Tsmin)
120 °C
Preheat: Temperature Max (Tsmax)
170 °C
Preheat: Time (tsmin to tsmax)
65-150 seconds
Time Maintained Above: Temperature (TL)
Time Maintained Above: Time (tL)
217 °C
45-90 seconds
Peak/Classification Temperature (Tp)
235 - 245 °C
Time Within 5 °C of Actual Peak Temperature (tp)
20-40 seconds
Ramp-Down Rate
1 - 6 °C/second
Time 25 °C to Peak Temperature
4 minutes max.
Note: All temperatures refer to the topside of the package, measured on the package body surface.
Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
9
XLamp ® XM-L2 LED
Notes
Measurements
The luminous flux, radiant power, chromaticity and CRI measurements in this document are binning specifications only and solely
represent product measurements as of the date of shipment. These measurements will change over time based on a number of factors
that are not within Cree’s control and are not intended or provided as operational specifications for the products. Calculated values are
provided for informational purposes only and are not intended as specifications.
Pre‑Release Qualification Testing
Please read the LED Reliability Overview for details of the qualification process Cree applies to ensure long-term reliability for XLamp
LEDs and details of Cree’s pre-release qualification testing for XLamp LEDs.
Lumen Maintenance
Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED lumen maintenance.
For information on the specific LM‑80 data sets available for this LED, refer to the public LM-80 results document.
Please read the Long-Term Lumen Maintenance application note for more details on Cree’s lumen maintenance testing and forecasting.
Please read the Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect
the LED junction temperature.
Moisture Sensitivity
Cree recommends keeping XLamp LEDs in the provided, resealable moisture-barrier packaging (MBP) until immediately prior to soldering.
Unopened MBPs that contain XLamp LEDs do not need special storage for moisture sensitivity.
Once the MBP is opened, XLamp XM-L2 LEDs may be stored as MSL 1 per JEDEC J-STD-033, meaning they have unlimited floor life in
conditions of ≤ 30 ºC/85% relative humidity (RH). Regardless of the storage condition, Cree recommends sealing any unsoldered LEDs
in the original MBP.
RoHS Compliance
The levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold
limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2011/65/EC (RoHS2), as
implemented January 2, 2013. RoHS Declarations for this product can be obtained from your Cree representative or from the Product
Documentation sections of www.cree.com.
REACh Compliance
REACh substances of very high concern (SVHCs) information is available for this product. Since the European Chemical Agency (ECHA)
has published notice of their intent to frequently revise the SVHC listing for the foreseeable future, please contact a Cree representative to
insure you get the most up-to-date REACh SVHC Declaration. REACh banned substance information (REACh Article 67) is also available
upon request.
Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
10
XLamp ® XM-L2 LED
Notes - Continued
UL® Recognized Component
Level 4 enclosure consideration. The LED package or a portion thereof has been investigated as a fire and electrical enclosure per ANSI/
UL 8750.
Vision Advisory
WARNING: Do not look at exposed lamp in operation. Eye injury can result. For more information about LEDs and eye safety, please refer
to the LED Eye Safety application note.
Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
11
XLamp ® XM-L2 LED
Mechanical Dimensions
6
5
4
NOTICE
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
CONTAINED WITHIN ARE THE PROPRIETARY AND
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
MAY NOT BE
5COPIED, REPRODUCED OR DISCLOSED TO ANY
4
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
OF CREE INC.
REV
Thermal
vias, if present, are not shown on these drawings.
6
NOTICE
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
CONTAINED WITHIN ARE THE PROPRIETARY AND
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
OF CREE INC.
3
3
2
1
4.78
REVISONS
All measurements are ±.13 mm unless otherwise indicated.
REV
BY
DESCRIPTION
APP'D
3.78
DATE
3.02
2.78
4.78
D
5.00
3.78
3.02
.50
0.73
.50
2.78
5.00
.50
0.73
.50
5.00
5.00
4.78
R2.26
C
R2.26
Bottom View
Side View
Top View
.50
.80
.50
.50
.25
.50
B
.80
.50
.50
.80
.25
4.78
.80 4.78
.25
4.78
4.78
.25
.97
2.78
2.78
RECOMMENDED PCB SOLDER PAD
Recommended PCB4.78
Solder
Pad
Recommended Stencil Pattern
UNLESS OTHERWISE SPECIFIED
(Shaded Area
Is Open)
DIMENSIONS
ARE IN
RECOMMENDED STENCIL PATTERN
(HATCHED AREA IS OPENING)
RECOMMENDED PCB SOLDER PAD
THIRD ANGLE PROJECTION
6
5
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
.XX
±
.25
.XXX ±
.125
X°
±
.5 °
FOR SHEET METAL PARTS ONLY
4
.X
±
1.5
.XX
±
.75
.XXX ±
.25
X°
±
.5 °
SURFACE FINISH:
6
5
4
3
1.6
DATE
DRAWN BY
DATE
--
.X
±
.XX
±
.XXX ±
X°
±
--
APPROVED
DATE
--
--
MATERIAL
--
TITLE
D. CRO
--
APPROVED
1.5
.75
.25
.5 °
--
Phone (919) 313-5300
Fax (919) 313-5558
FINAL PROTEC
FINISH:
OUTLINESURFACE
DRAWING,
5050 XMLB
1.6
3
SIZE
FINAL PROTECTIVE FINISH
--
DRAWN BY
CHECK
4600 Silicon Drive
FOR SHEET METAL PARTS ONLY Durham, N.CMATERIAL
27703
THIRD ANGLE
PROJECTION
D. CRONIN
11/14/12
CHECK
± .13MM UNLESS O
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
.XX
±
.25
.XXX ±
.125
X°
±
.5 °
RECOMMENDED STENCIL PATTERN
(HATCHED AREA IS OPENING)
ALL DIMENSIONS ARE
± .13MM UNLESS OTHERWISE NOTED
.97
A
4.78
ALL DIMENSIONS ARE
4.78
4.78
SCALE
C
DRAWING NO.
2610-00032
SHEET
16.000
2
1
Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
12
OF
6
5
4
3
2.00[.079]
4.00[.157]
1
2
REVISIONS
NOTICE
EE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
NTAINED WITHIN ARE THE PROPRIETARY AND
NFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
Y NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
AUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT
CREE INC.
DESCRIPTION
REV
BY
DATE
APP'D
POCKET SIZE
+.10
+.0039
.0591
-.00
-.0000 [ ]
Do1.50
P2
1.75[.069]
E1
Po
Ao -
5.40mm [.213"]
Bo -
5.40mm [.213"]
Ko -
3.35mm [.132"]
Tape and Reel
3.0°
XLamp ® XM-L2 LED
D
5.40[.213]
Bo
3
12.00[.472] Component Handling Systems Standard.
All Cree carrier tapes conform to EIA-481D,
Automated
6
5
4
5.50[.217]F
6
5
4
NOMINAL
C
NOTICE
CREE CONFIDENTIAL. THIS PLOT
AND THE INFORMATION
NOTICE
CONTAINED
WITHIN ARE THETHIS
PROPRIETARY
ANDINFORMATION
CREE CONFIDENTIAL.
PLOT AND THE
CONFIDENTIAL
INFORMATION
CREE,
INC. THIS PLOT
CONTAINED
WITHIN AREOF
THE
PROPRIETARY
AND
MAY NOT
BE COPIED, INFORMATION
REPRODUCEDOF
ORCREE,
DISCLOSED
TO PLOT
ANY
CONFIDENTIAL
INC. THIS
UNAUTHORIZED
PERSON
WITHOUT
THE WRITTEN
CONSENT
MAY NOT BE COPIED, REPRODUCED
OR DISCLOSED
TO ANY
OF CREE
INC.
UNAUTHORIZED
PERSON WITHOUT THE WRITTEN CONSENT
OF CREE INC.
D
D
2.00[.079]
2.00[.079]
P2
1.50[.059]
4.00[.157]
D1
4.00[.157]
Po
8.00[.315]
P
REVISIONS
REVISIONS
DESCRIPTION
DESCRIPTION
REV
3.0°
B
6
7.0°
5
C
NOTICE
NTIAL. THIS PLOT AND THE INFORMATION
THIN ARE THE PROPRIETARY AND
INFORMATION OF CREE, INC. THIS PLOT
OPIED, REPRODUCED OR DISCLOSED TO ANY
D PERSON WITHOUTTHE WRITTEN CONSENT
5.40[.213]
4
A
B
Ao
B
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
.XX ±
.01
.XXX ±
.005
X°
±
.5 °
FOR SHEET METAL PARTS ONLY
.X
±
.06
.XX ±
.03
.XXX ±
.010
X°
±
.5 °
SURFACE FINISH:
5
D
4
8
6
1
C
BY
DATE
DDS
11/8/10
DC
2/26/12
BS
8.00[.315]
DATE
8.00[.315]
P TITLE
P
APPROVED
SIZE
A
Loaded Pockets
(1000 Lamps)
A
FINAL PROTECTIVE FINISH
User Feed Direction
REV.
DRAWING NO.
2402-00011
7.0°
SCALE
DRAWING SCALE
2
SHEET
7.0°
1
A
OF
4
1.75
3.35[.132]
3.35[.132]
3
Ko
Ko
START
12
.36[.014] D
T .36[.014]
T
A
XM 5050 CARRIER TAPE
MATERIAL
5.40[.213]
5.40[.213]
Ao
ANODE SIDE
1.50[.059]
Phone (919) 313-5300
Fax (919) 313-5558
D1 1.50[.059]
D1
B
3.35
2
1
2400-00009
CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275
CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275
INDEX
QTY
ITEM
1
1
2400-00009-CORE
DRAWN BY
COMMENTS
DATE
UNLESS OTHERWISE SPECIFIED
DATE
4/23/10
2 D. CRONIN
2DRAWN BY2400-00009-REEL
UNLESS ARE
OTHERWISE
SPECIFIED
DIMENSIONS
IN INCHES
D. CRONIN
4/23/10
DATE
DIMENSIONS
ARE IN INCHESCHECK
AND
AFTER FINISH.
CHECK
DATE
AND
AFTERSPECIFIED:
FINISH.
TOLERANCE
UNLESS
TOLERANCE
.XX ± UNLESS
.01 SPECIFIED:
APPROVED
DATE
TITLE
.XX
±
.01
.XXX ±
.005
APPROVED
DATE
TITLE
X°
±.XXX .5± ° .005
THIRD ANGLE PROJECTION
MATERIAL
X° PARTS
±
.5
°
FOR SHEET METAL
ONLY
Leader
THIRD ANGLE PROJECTION
MATERIAL
FOR.XSHEET
± METAL
.06 PARTS ONLY
DRAWING NO.
400mm (min.) of
SIZE
.XX .X
±
±.03 .06
DRAWING NO.
SIZE
FINAL PROTECTIVE FINISH
±
.03
empty pockets with
.XXX .XX
±
.010
FINAL PROTECTIVE FINISH
X°
±.XXX .5± ° .010
at least 100mm
SCALE
X°
±
.5 °
SURFACE FINISH: 63
SCALE
sealed by tape
DRAWING
SCALE
SURFACE FINISH: 63
DRAWING SCALE
Ao
C
4600 Silicon Drive
Durham,
N.C
27703
4600
Silicon
Drive
Durham,
N.C 27703
Phone (919)
313-5300
Phone
(919) 313-5300
Fax (919)
313-5558
Fax (919) 313-5558
XMXM
5050
CARRIER
TAPE
5050
CARRIER
TAPE
2402-00011
A
2402-00011 A
6
(405 empty pockets min.)
4
5
3
4
2
3
A
REV.
A
6
SHEET
OF
SHEET
1
2
1OF / 1
1
D
REV.
A
1 /1
12.4
+.2
.0
MEASURED AT HUB
C
C
330
+.25
-.75
16.4
+0.2
.0
MEASURED AT HUB
THIRD ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
.XX ±
.25
.XXX ±
.125
X°
±
.5 °
FOR SHEET METAL PARTS ONLY
.X
±
1.5
.XX ±
.75
.XXX ±
.25
X°
±
.5 °
SURFACE FINISH:
5
4
1.6
3
1.9±.4
DATE
DRAWN BY
D. CRONIN
CHECK
21 ±.4
4600 Silicon Drive
Durham, N.C 27703
06/08/10
DATE
--
Phone (919) 313-5300
--
Fax (919) 313-5558
A
DATE
APPROVED
--
--
MATERIAL
TITLE
13.1 ±.2
--
SIZE
FINAL PROTECTIVE FINISH
--
SCALE
XM LOADING SPEC
REV.
DRAWING NO.
C
2402-00012
SHEET
3.000
2
B
OF
B
1 /1
1
12.4
+1.0
-.5
MEASURED AT EDGE
60°
60°
REVISONS
REV
DESCRIPTION
BY
DATE
APP'D
Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
UNLESS OTHERWISE SPECIFIED
DRAWN BY
A
THIRD ANGLE PROJECTION
B
1 /1
B
B
C
APP'D
4600 Silicon Drive
Durham, N.C 27703
4/23/10
DATE
CATHODE SIDE
4
5
Trailer
160mm (min) of
empty pockets
sealed with tape
(15 pockets min.)
D. CRONIN
CHECK
3
A
6
D
DATE
DRAWN BY
63
NOTICE
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
CONTANED WITHIN ARE THE PROPRIETARY AND
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT
OF CREE INC.
D
APP'D
DATE
APP'D
CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275
B
END
2
BY
5.40[.213]
5.40[.213]
Bo
Bo
3.0°
12.00[.472]
12.00[.472]
NOMINAL
NOMINAL
REVISONS
[.484]
10.25 12.30DESCRIPTION
12.30
[.484]
MAX
Loaded pocket
count was 750
[.404]10.25
MAX
[.404]
WANODE
E2
MADE CATHODE AND
W NOTE LARGER
E2
REV
3.35[.132]
Ko
THIRD ANGLE PROJECTION
6
5.50[.217]F
5.50[.217]F
3
C
1
DATE
BoBo
- - 5.40mm
[.213"]
5.40mm
[.213"]
KoKo
- - 3.35mm
[.132"]
3.35mm
[.132"]
1.75[.069]
E1 1.75[.069]
E1
.36[.014]
T
Po
BY
POCKET
SIZE
POCKET
SIZE
AoAo
- - 5.40mm
[.213"]
5.40mm [.213"]
+.10
+.0039
Do1.50
.0591
+.0039
-.00 +.10 .0591
-.0000
[]
Do1.50
-.00
-.0000 [ ]
P2
1
2
Except as noted, all dimensions in mm.
REV
12.30 [.484]
MAX
W
10.25
[.404]
E2
2
3
DIMENSIONS ARE IN INCHES
AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
.XX ±
.01
.XXX ±
.005
X°
±
.5 °
FOR SHEET METAL PARTS ONLY
D. CRONIN
CHECK
DATE
4600 Silicon Drive
Durham, N.C 27703
09/29/09
13
DATE
-APPROVED
-MATERIAL
Phone (919) 313-5300
--
Fax (919) 313-5558
DATE
--
TITLE
REEL, 13" X 12MM, 3 PIECE SNAP
A
A
XLamp ® XM-L2 LED
Packaging
Humidity Indicator
Card (inside bag)
Dessicant
(inside bag)
Unpackaged Reel
Label with Cree Bin Code,
Quantity, Reel ID
Packaged Reel
Label with Cree Bin
Code, Qty, Lot #
Vacuum-Sealed
Moisture Barrier Bag
Label with Cree Order Code,
Quantity, Reel ID, PO #
Label with Cree Bin Code,
Quantity, Reel ID
Label with Custo
Code, Qty, Reel I
Boxed Reel
Label with Cree Order Code,
Quantity, Reel ID, PO #
Patent Label
Label with Cree Bin Code,
Quantity, Reel ID
Patent Label
Copyright © 2012-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
14