Designed, Manufactured and Assembled in Lewiston, Idaho USA

advertisement
Designed, Manufactured and Assembled
in Lewiston, Idaho USA
Caliber Specific Powder Funnels...
The new, caliber specific powder funnels are machined
from solid bar stock on CNC turning centers. These
precision funnels are meticulously machined to exacting
tolerances then buffed for a perfectly smooth ID finish. This
allows the powder to flow smoothly into the case mouth
without stacking.
The funnels are color coded with a bright dip anodized
finish and then laser engraved with the caliber on the funnel
base for easy identification on your reloading bench.
These funnels are anti-static with all powders and stay
upright while on the case neck in your reloading block.
Slotted Hybrid Muzzle Brake...
Our new Slotted Hybrid Brake is designed to drastically reduce recoil with aggressive slotting and internal bore stepping.
The top and angular round hole porting reduces muzzle jump so you can better see your bullet impact. This porting does not
go all the way around the brake body, only the upper 180 degrees, thus reducing dust blasting on proned out shooting, and
concussion on bench shooting.
All brakes made with 1.000” od 416 stainless steel.
Note: Must be gunsmith installed for timing to the barrel and boring to correct caliber +.020 over.
Material is allowed for final light turning, tapering to blend to barrel diameter at the rear and bead blasting if desired.
MADE IN THE USA
Available in the following calibers:
.375, .338, .308, .284, .277, .264,
.257, .244, .224, .204, .177
MADE IN THE USA
The funnel rack is designed to keep
your reloading funnels out of the way,
but easy to grab when you need it.
Picking the right funnel is always a
snap thanks to our laser engraved
caliber identifier on the funnel
base and caliber specific color
coded bright anodized finish.
Made in the USA
Slotted Hybrid Muzzle Brake Specifications
416 Stainless Steel
1.00 diameter
1/2”-28 thread
2.600” overall length
PART # HC-91120
416 Stainless Steel
1.00 diameter
9/16”-28 thread
2.600” overall length
PART # HC-91121
416 Stainless Steel
1.00 diameter
5/8”-24 thread
2.600” overall length
PART # HC-91122
1.
The cut away at left shows the smooth unrestricted passage into the case mouth.
The shoulder of the case fits into a counter bore that is the average neck diameter
of a case neck OD. of that caliber.
This configuration allows even the finest powders to flow into the case without
hanging up on the edge of the case mouth.
2.
3.
The cut away above shows the brake cross section.
The first radial chamber with angular holes combined with the holes at the top of the brake
direct gasses upward to reduce muzzle jump (1).
Caliber specific means the funnel ID. and the inside of the case
neck are the same diameter, This allows the powder to transfer from
funnel to case smoothly. No more tapping the funnel everytime you
pour powder to get it to flow into the case!
XHCG products are designed, manufactured, and
assembled in Lewiston, Idaho USA
The two side holes at the first radial chamber help to disperse felt concussion from the large
volume of gasses striking the front of each of the slotted baffles (2).
The three slots (baffles) are separated by a series of larger than finish bore diameter holes to
help distribute gasses to each of the slotted baffles more efficiently, thus improving the forward
motion of the rifle to reduce felt recoil (3).
Tru Level Pic Rail...
.600”
The average pic rail
height is .600” from
the top of the receiver
to the top of the pic
rail. This provides bolt
clearance under the
level housing.
TRU Level™ Pic Rail Centerfire Rifles
Long range shooting requires a level gun, as any tilt in the gun translates into a serious windage error at longer ranges. When
using the TRU Level™ Scope Base, your level and scope eye piece are in the same sight picture. This allows you to check
the level while aiming without having to raise your head from the shooting position. With the level housed in the machined
picatinny base, it is protected from being bumped out of level as often happens with some scope level systems. If you are
serious about long range shooting, you need a TRU Level™ Picatinny Mount
MADE IN THE USA
AR Tactical Level...
AR Tactical Level
The new AR Tactical Level offers the mid to long range AR shooter an anti-cant device that is compact and mounts completely
out of the way. The sides are sculpted so you can easily reach the charging handle with no chance of snagging the level
mount. No more worries about tearing off or bumping a level that protrudes from the side of the pic rail. The TRU Level is
always in your sight picture while shooting, so no more lifting your head to check the cant of your rifle while executing a shot.
MADE IN THE USA
Specifications:
• Precision level mounted into a CNC machined picatinny base for perfect level to base alignment.
• Constant level verification when in head down shooting position.
• MIL-STD 1913 Picatinny Cross Slots.
• Billet machined 7075 T-6 Aluminum. Source USA Mills
• Black Anodize Mill Spec 8625 Type 3 Hardcoat
• Mounting Screws: (4) 6-48 Torx .225 Head dia. @ 22 Inch Pounds. Source USA
Specifications:
• Constant level verification when in head down shooting position.
• CNC machined 6061 T-6 aluminum. Source USA Mills
• Black Anodize Mill Spec 8625 Type 3 Hardcoat.
• Fits all AR15 rifles with MIL-STD 1913 Picatinny Cross Slots.
• Side cut at the rear for ample hand clearance when operating the charging handle.
• The Height of the level body from the top of the pic rail to top of level is .375”
Gun Model
Action type
MOA spec
Remington 700
Long action
0 MOA
YES
Short action
0 MOA
YES
Long action
20 MOA
YES
Short action
20 MOA
YES
Winchester Model 70 after pre 64 actions
Built with 3 screw holes in the rear to fit both Long
and Magnum actions.
Long/Magnum
action
20 MOA
YES
Savage Mod 110, 111, 112,114, and 116
No recoil lug to accommoidate all round top actions
with top or side ejection port.
Long action
0 MOA
NO
Long action
20 MOA
NO
Short action
0 MOA
NO
Short action
20 MOA
NO
Savage Mod 10, 11, 12, 14 and 16
No recoil lug to accommodate all round top actions
with top or side ejection port.
Recoil lug
Tactical Long Range Rings...
The “Tank” Crosshair Level...
The Force Recon Tactical Rings feature a built in level housed into the lower portion of the rear scope ring. Having the level in
the base of the ring assures that it is always perfectly parallel to the top of the picatinny rail which is essential for long range
shooting. A perfectly plumb scope and rifle are essential for the bullet to follow a true vertical line throughout the projectile's
path to the target.
These precision long range rings offer precise mounting for your optics onto the picatinny base and will not allow the scope
to move under any recoil scenario. Our wide .875
mounting platform offers a stable interface with
the pic rail while the 2 cross slot bolts provide
awesome clamping power. We go one step further
by installing a pair of stainless steel guide rails that
press into the ring base. The ring base clamp rides
on these rails to keep the clamp perfectly aligned
as the 2 cross slot bolts are drawn tight against the
pic mount.
MADE IN THE USA
The Ranger Rings offer all of the same rugged
design features as our Force Recon Rings,
without the integrated level.
If you want the best in a 30 or 34mm tactical ring,
this is it!
The “Tank” is CNC machined from solid steel to give it the weight
necessary for no-hassle crosshair leveling. First, your rifle's action must
be level. Then to level the crosshair in your scope to the leveled action,
place the “Tank” on top of your elevation turret with the scope ring
caps loosely in place. Then rotate your scope until the bubble lines up
between the lines in the tank and you are now plumb to the rifle. Finally,
tighten the scope ring cap screws evenly until tight and you are ready to
hit the range.
MADE IN THE USA
Specifications:
Force Recon & Ranger Precision Scope Rings
Ring Bore Diameter:
30mm Tol. +/-.001”
34mm Tol. +/-.001”
Material: Source USA Mills
Billet 7075 T-6 Aircraft Aluminum
Finish Anodize:
Black Anodize Mill Spec 8625 Type 3 Hardcoat
Ring Height 30mm Medium:
Top of pic mount to bore center
1.000”
Rings are matched within .002”
Ring Height 30mm Medium:
Top of pic mount to bottom of the scope bore
.406”
Rings are matched within .002”
Ring Height 30mm Low:
Top of pic mount to bore center
.850”
Rings are matched within .002”
Ring Height 30mm Low:
Top of pic mount to bottom of the scope bore
.260”
Rings are matched within .002”
Ring Height 34mm:
Top of pic mount to bore center
.900”
Rings are matched within .002”
Ring Height 34mm:
Top of pic mount to bottom of the scope bore
.235”
Rings are matched within .002”
Cap Screws: (6) Source USA
Ruger® 10/22® Pic Rail with level...
TRU Level™ Picatinny Mount for the legendary Ruger® 10/22®...
Top accuracy requires a level gun. Even a slight canting of your rifle will cause windage errors. The TRU Level Pic Rail
features a precision level housed in the CNC machined picatinny base. This mounting system protects the level from being
bumped out of plumb during hard use.
The unique location also keeps your level and scope eye piece in the same sight picture, allowing you to check the level when
aiming, without raising your head from the shooting position.
If you are serious about rimfire shooting and varminting, you need a TRU Level Picatinny Mount on your tricked out Ruger®
10/22®.
Available in Black
MADE IN THE USA
10/22® TRU Level™ Picatinny Mount Specifications:
Material: Source USA Mills
6061 T-6 Aluminum
8-40 #15 Torx @ 20 Inch Pounds
Finish:
Black Anodize Mill Spec 8625 Type 3 Hardcoat
Clamp Screws: (2) Source USA
10-24 SHC Grade 8
Mounting Screws: (4) Source USA
6-48 Torx #15 @15 Inch Pounds.
Clamp guide Rails: (2) Source USA
.125 Precision dowel pins
Picatinny Configuration:
(14), MIL-STD 1913 Picatinny Cross Slots.
Radial Ported Muzzle Brake...
We make 416 stainless steel and 4140 carbon steel muzzle brake blanks
for gunsmiths. These brakes are precision machined on our CNC turning
centers.
Although we call this a blank, we do most of the work for you. They are
threaded and counter-bored for the barrel thread and shoulder. The 30
ported holes are .191 diameter and chamfered to save you time.
We have drilled a .250 dia. pilot hole through the brake, and you must
finish bore that hole to accommodate the caliber of the gun build plus
.020 overbore clearance. These brakes are sold to gunsmiths only, as
professional installation is required to make sure the correct bore size is
used in the gun build.
MADE IN THE USA
AR 30 Hole Ported Muzzle Brake...
These brakes are designed to be installed on 223/5.56 cal. AR15 rifles with
.750 barrels. This brake will reduce recoil and muzzle jump significantly and
improve your time on target with follow up shots and double tap drills..
Specifications:
Thread: 1/2-28 Class 2
Material: 4140 Carbon Steel
Finish: Black Oxide
MADE IN THE USA
Gunsmith Installed Muzzle Brake Blank Specifications
416 Stainless
Steel
4140 Carbon
Steel
1.00 diameter
5/8”-24 thread
2.00” overall length
PART # HC-91110
.875 diameter
9/16”-28 thread
2.00” overall length
PART # HC-91111
.750 diameter
1/2”-28 thread
2.00” overall length
PART # HC-91112
1.00 diameter
5/8”-24 thread
2.00” overall length
PART # HC-91115
.875 diameter
9/16”-28 thread
2.00” overall length
PART # HC-91116
.750 diameter
1/2”-28 thread
2.00” overall length
PART # HC-91117
Xtreme Hardcore Gear
PO Box 319
3101 North South Highway
Lewiston, ID 83501
208-746-7065
Xtreme Hardcore Gear is an Alpine Archery Company
Download