BATTERY POWERED
DRIVER
For inserting screws into
varied bone densities
USERS MANUAL
Table of Contents
Introduction
Battery Powered Driver
Operating Instructions
Assembly3
Product Information
2
Screw Insertion
4
Manual Use
5
Screw Removal
6
Blade Removal
6
Cleaning and Sterilization
7
Battery Powered Driver System
8
Battery Powered Driver DePuy Synthes CMF
BATTERY POWERED DRIVER
Hand Piece (05.000.008)
• Forward speeds: 225 and 295 rpm
• Reverse speed: 295 rpm
• Maximum torque: ≈ 0.46 Nm (65 oz-in)
• Weight: 311 grams (10 oz)
• Operating temperature: 15°–35°C (59°–95°F)
Speed controls
(2 forward plus
reverse)
Drive-lock
nose cone
Single-use, sterile
battery pack attaches
to hand piece
Hex coupling
Features
• Two insertion speeds for placing screws
into varied bone densities
• One reverse speed for removing screws
• Drive-lock mechanism for manual insertion
or removal of screws
• Easily connects to DePuy Synthes hex coupling
screwdriver blades
• Hand piece is autoclavable
Single-use Battery Pack, sterile (05.000.007.01S)
No sterilization is required for the single-use battery pack.
The battery pack is sterile-packed and precharged.
Important: Do NOT sterilize. Do NOT charge.
STERRAD® Battery (05.000.010)
STERRAD Battery is provided non-sterile.
Important: Use STERRAD sterilization process
only prior to use. Do not charge or autoclave.
Complies with standards: UL2601-1, UL60601, IEC60601-1, EN60601-1-2,
EN55022, EN55014-2, EN61000-4-2, EN61000-4-3, CAN/CSA C22.2 No. 601-M90
2
DePuy Synthes CMF Battery Powered Driver
Users Manual
OPERATINg INSTRUCTIONS
1
Connect battery pack to hand piece
Instruments
05.000.007.01S
or
05.000.010
Battery Pack, sterile
05.000.008
Hand Piece, for Battery Powered Driver
STERRAD Battery
Align the battery pack with the corresponding shape on
the hand piece. Press the battery pack onto the hand piece
until secure.
Note: If Hand Piece powers on without pressing
power button, then disconnect Battery Pack and
use a different Battery Powered Driver Hand Piece.
2
Insert blade into nose cone
Insert the appropriate hex coupling screwdriver blade
while pushing down on the nose cone. Release the
nose cone, and verify that the blade is locked in place.
Battery Powered Driver
Users Manual
DePuy Synthes CMF
3
Operating Instructions
3
Screw insertion
Choose the appropriate speed to insert screws.
Load screw and press appropriate power button to insert.
Alignment
When placing screws, maintain vertical alignment of the
screwdriver and screw to prevent disengagement from
the screwhead (Figure 1).
High speed
gently rock the screwdriver once from side to side to
release the blade from the head of the screw (Figure 2).
Caution: In order to avoid breakage of a partially
inserted screw, manually back out the screw one
revolution before reattempting power insertion.
Note: If Hand Piece fails to turn on, check if drivelock mechanism is engaged (see Figure 3 on the
following page). If Hand Piece still fails to turn on,
then disconnect battery pack and use a different
Battery Powered Driver Hand Piece.
Figure 1
Figure 2
4
DePuy Synthes CMF Battery Powered Driver
Users Manual
Low
speed
Reverse
Operating Instructions
Manual use
Maintain the screw/blade engagement in situ and turn
the nose cone to the closed-lock position. The drive-lock
mechanism is engaged when the indicator is aligned
with the closed-lock symbol on the nose cone (Figure 3).
The driver can now be used manually to complete final
seating of the screw.
Return to power
If the drive-lock mechanism is engaged (manual mode),
turn the nose cone back to the unlock position (Figure 4)
to resume power insertion.
Figure 3
Figure 4
Battery Powered Driver
Users Manual
DePuy Synthes CMF
5
Operating Instructions
4
Screw removal
Manual removal
To remove a screw manually, the drive-lock mechanism must
be engaged. Prior to engaging the blade in the screw, turn
the nose cone to the lock position. Manual
removal can now be achieved.
Power removal
To remove a screw with power, turn the nose cone to the
unlock position and depress the orange reverse button.
5
Blade removal
To remove the screwdriver blade from the hand piece,
push down on the nose cone and firmly pull the blade
out to release.
6
DePuy Synthes CMF Battery Powered Driver
Users Manual
Cleaning and Sterilization
Cleaning
Hand Piece (05.000.008)
7. Visually inspect the hand piece. Repeat Steps 2–6 until
no visible soil remains on the device.
Note: Do not submerge or soak power equipment
8. Perform a final rinse using deionized or purified water
for a minimum of two minutes.
in aqueous solutions!
Manual clean only.
Do not use a brush, sharp object or pressurized
water to clean the contact plate. Do not soak,
immerse or clean the hand piece in washer/sterilizer.
Do not expose to saline solution. Saline will shorten
instrument life. Do not lubricate or oil the hand piece.
1. Remove the battery pack from the hand piece.
2. Rinse the hand piece under running cold tap water for a
minimum of three minutes. Use a soft, lint free cloth and/
or soft-bristled brush to assist in the removal of gross soil
and debris. Manipulate all moving parts under running
cold tap water to loosen and remove gross debris.
3. Spray the hand piece using a neutral pH enzymatic
solution or foam spray and let it sit for three minutes.
Follow the enzymatic detergent manufacturer’s
instructions for use for correct temperature, water
quality (i.e., pH, hardness) and concentration/dilution.
4. Rinse the hand piece with cold tap water for a minimum
of two minutes. Use a syringe, pipette or water jet to flush
lumens, channels and other hard to reach areas.
5. Clean the hand piece manually under running warm
water using a neutral enzymatic detergent for a
minimum of five minutes. Use a soft-bristled brush
and/or soft, lint free cloth to remove all visible soil
and debris. Actuate the drive-lock mechanism for
thorough cleaning. Follow the enzymatic detergent
manufacturer’s instructions for use for correct
temperature, water quality (i.e., pH, hardness)
and concentration/dilution.
6. Rinse the hand piece using cool to lukewarm running
tap water for a minimum of two minutes. Use a syringe,
pipette or water jet to flush lumens and channels.
Actuate the drive-lock mechanism and rinse thoroughly
under running water.
9. Dry the hand piece using a soft, lint free cloth, or clean
compressed air.
Minimum Sterilization Requirements
Prevacuum
Steam sterilize at 132°C (270°F) for 4 minutes.
Minimum dry time: 20 minutes.
Important: Do NOT use STERRAD Sterilization
System. Allow to cool to room temperature
before use.
Sterilization times represent exposure times only,
not total cycle times.
Battery Pack, sterile (05.000.007.01S)
Lithium*
Battery pack is for single use only. Dispose after use.*
Note: For more information, please see package
insert.
Single-use battery pack is provided sterile unless
package is opened or damaged.
Important: Do NOT sterilize. Do NOT recharge.
Sterrad Battery (05.000.010)
Lithium*
Note: For more information, please see package
insert.
Sterrad battery is provided non-sterile. Use Sterrad
sterilization process only prior to use. Do not charge
or autoclave.
* Consult local laws regarding disposal. Batteries may be safely
disposed of with hospital waste.
Battery Powered Driver Users Manual DePuy Synthes CMF 7
BATTERY POWERED DRIVER SYSTEM
Battery Powered Driver
05.000.007.01S Battery Pack, sterile, for Battery
Powered Driver
05.000.008
Hand Piece, for Battery Powered Driver
05.000.010
STERRAD Battery, for Battery Powered
Driver
Hex Coupling Accessories
313.917
313.935
313.936
313.928
313.939
Cruciform Screwdriver Blades, self-retaining
1.3 mm
1.5 mm/2.0 mm, short
1.5 mm/2.0 mm, long
2.0 mm/2.4 mm
313.97
2.4 mm/3.0 mm Cruciform Screwdriver
Blade
Holding Sleeve
313.252
313.253
313.254
313.805
313.806
PlusDrive Screwdriver Blades, self-retaining
1.5 mm/2.0 mm, 96 mm
1.5 mm/2.0 mm, 76 mm
1.5 mm/2.0 mm, 52 mm
1.3 mm, 52 mm
1.3 mm, 76 mm
8
DePuy Synthes CMF Battery Powered Driver
Users Manual
Cruciform Blade
PlusDrive Blade
Battery Powered Driver System
313.931
313.932
Low Profile Neuro Cruciform Screwdriver
Blades, self-retaining
short
medium
03.503.016
03.503.017
MatrixNEURO Screwdriver Blades,
self-retaining
short
medium
03.503.070
03.503.071
03.503.072
MatrixMANDIBLE/MatrixThorax Screwdriver
Blades, self-retaining
short
medium
long
03.503.201
03.503.202
03.503.203
MatrixMIDFACE Screwdriver Blades,
self-retaining
52 mm
76 mm
96 mm
Low Profile Neuro
Cruciform Blade
Matrix Blade
Battery Powered Driver
Users Manual
DePuy Synthes CMF
9
Limited Warranty and Disclaimer: DePuy Synthes CMF products are sold with a limited warranty to the original purchaser against defects in
workmanship and materials. Any other express or implied warranties, including warranties of merchantability or fitness, are hereby disclaimed.
WARNING: In the USA, this product has labeling limitations. See package insert for complete information.
CAUTION: USA Law restricts these devices to sale by or on the order of a physician.
Not all products are currently available in all markets.
DePuy Synthes CMF
1302 Wrights Lane East
West Chester, PA 19380
Telephone: (610) 719-5000
To order: (800) 523-0322
Synthes (Canada) Ltd.
2566 Meadowpine Boulevard
Mississauga, Ontario L5N 6P9
Telephone: (905) 567-0440
To order: (800) 668-1119
Fax: (905) 567-3185
www.depuysynthes.com
© DePuy Synthes CMF, a division of DOI 2013. All rights reserved.
J5594-E 11/13