HOME
AMP MULTILOCK ELECTRICAL CONNECTORS
REMOVING SOCKET/PIN
TERMINALS
B.1
inadvertently released. Repeat the step without releasing
the tang.
1.
Remove connector from the retaining device, either
attachment or rosebud clip.
2.
Depress the button on the socket terminal side of the
connector (plug) and pull apart the pin and socket
halves.
3.
Bend back the latch slightly and free one side of secondary lock, then repeat the step to release the other side.
Rotate the secondary lock outward on hinge to access
terminals in chambers of connector housing.
4.
Looking in the terminal side of the connector (opposite
the secondary lock), take note of the cavity next to each
terminal.
5.
See Figure B-1. With the flat edge against the terminal,
insert the pick tool (Snap-On TT600-3) into the cavity
until it stops. Pivot the end of the pick away from the terminal (locktab is inside housing) and gently tug on wire to
pull terminal from chamber. Do not tug on the wire until
the tang is released or the terminal will be difficult to
remove. A “click” is heard if the tang is engaged but then
●
●
NOTES
If pick tool is not available, a push pin/safety pin may be
used instead.
An ELECTRICAL TERMINAL CRIMP TOOL (Part No.
HD-41609) is used to install Amp Multi lock pin and
socket terminals on wires. If new terminals must be
installed, see Crimping Instructions on the next page.
INSTALLING SOCKET/PIN
TERMINALS
NOTE
For wire location purposes, numbers are stamped into the
secondary locks of both the socket and pin housings. See
Figure B-2.
1.
From the secondary lock side of the connector, insert the
terminal into its respective numbered chamber until it
snaps in place. For proper fit, the slot in the terminal
must face the tang in the chamber.
d0242x3x
Pin terminal
Secondary lock open
Pin housing
Socket housing
Latch
Secondary lock open
Button
Latch
Secondary lock open
Socket terminal
Figure B-1. 10-Place Amp Multilock Connector
2007 Buell Firebolt: Appendix B
B-1
HOME
d0243x8x
Socket terminal
Secondary lock open
4
Socket housing
2
Pick tool
1
3
Pin terminal
Secondary lock open
4
Pin housing
1
Pick tool
2
1.
2.
3.
4.
3
Open secondary lock.
Insert pick into cavity on inboard side
of connector.
Pivot end of pick to release tang.
Gently tug on wire to remove terminal
from housing.
Figure B-2. Release Tang and Back Out Terminals
●
●
NOTES
See Figure B-3. The tang in the chamber engages the
slot to lock the terminal in position.
On the pin side of the connector, tangs are positioned at
the bottom of each chamber, so the slot in the pin terminal (on the side opposite the crimp tails) must face downward.
●
On the socket side, tangs are at the top of each chamber,
so the socket terminal slot (on the same side as the
crimp tails) must face upward.
●
Up and down can be determined by the position of the
release button (used to separate the pin and socket
halves). Consider the button to always be on top of the
connector.
2.
Gently tug on wire end to verify that the terminal is
locked in place and will not back out of chamber.
3.
Rotate the hinged secondary lock inward until tabs fully
engage latches on both sides of connector.
4.
Insert the socket housing (plug) into the pin housing
(receptacle) until it snaps in place.
5.
Install connector on retaining device, either attachment
or rosebud clip.
B-2
Pin housing
2007 Buell Firebolt: Appendix B
Socket housing
Button
Tang
Tang
d0244x8x
Figure B-3. Multilock Connector Cutaway View
HOME
Secondary locks open (socket housings shown)
3
4
9
10
2
1
Stamped numbers on secondary locks indicate wire color locations
– AMP
1
– AMP
2
1
3
3-place
2
3
4
5
6
5
6
6-place
7
8
12-place
Secondary lock
Pin terminal
Socket housing
Button
Pin housing
Secondary lock
Pin terminal
Secondary lock
Socket terminal
Latch
Button
Pin housing
Latch
Socket housing
Secondary lock
Socket terminal
d0245x2x
Figure B-4. 3-Place and 6-Place Amp Multilock Connectors
2007 Buell Firebolt: Appendix B
B-3
HOME
CRIMPING INSTRUCTIONS
1.
Squeeze the handles to cycle the crimp tool (Part No.
HD-41609) to the fully open position.
2.
Raise locking bar by pushing up on bottom flange. With
the crimp tails facing upward, insert contact (socket/pin)
through locking bar, so that the closed side of the contact
rests on the front nest (concave split level area of the
crimp tool). See Figure B-3.
3.
Release locking bar to lock position of contact. When
correctly positioned, the locking bar fits snugly in the
space at the front of the core crimp tails.
1.
2.
3.
4.
Insulating crimp tail
Core crimp tail
Locking bar groove
Tang slot
4.
Strip lead removing 5/32 in. (4 mm) of insulation. Insert
wires between crimp tails until ends make contact with
locking bar. Verify that wire is positioned so that short
pair of crimp tails squeeze bare wire strands, while long
pair folds over insulation material.
5.
Squeeze handle of crimp tool until tightly closed. Tool
automatically opens when the crimping sequence is
complete. Raise up locking bar and remove contact.
6.
Inspect the quality of the core and insulation crimps. Distortion should be minimal.
1
3
2
2
1
4
3
4
1.
3.
Raise locking bar and seat contact
on front nest of crimp tool. Release
locking bar
Close and squeeze crimp tool.
2.
4.
Insert stripped lead until it
contacts locking bar.
Figure B-5. Amp Multilock Crimping Procedure
2007 Buell Firebolt: Appendix B
CRIMP TOOL
NEST
20
Front
16
Middle
18
Rear
Raise locking bar and remove contact.
d0246x8x
B-4
GAUGE
WIRE
HOME
DEUTSCH ELECTRICAL CONNECTORS
GENERAL
B.2
4566
Deutsch Connectors feature a superior seal to protect electrical contacts from dirt and moisture in harsh environments.
The connector also provides superior pin retention.
See Figure B-8. This 12-pin connector illustrates the various
parts of the Deutsch connector. The following instructions
may be followed for all 2-pin through 12-pin Deutsch connectors.
Socket housing: alignment tabs and/or external latch, secondary locking wedge, internal seal, wire seal, seal pin.
NOTE
Seal pins or plugs are installed in the wire seals of unused pin
and socket locations. If removed, seal pins must be replaced
to maintain the integrity of the environmental seal.
Pin housing: alignment grooves and/or external latch cover,
attachment clip, secondary locking wedge, wire seal, seal pin.
REMOVING/DISASSEMBLING
Figure B-6. Remove Secondary Locking Wedge
s0545x8x
Attachment clips are attached to the pin housings of most
connectors. The clips are then attached to T-studs on the
motorcycle frame. T-studs give positive location to electrical
connectors and wire harness. Consistent location reduces
electrical problems and improves serviceability.
1.
Push the connector to disengage small end of slot on
attachment clip from T-stud. Lift connector off T-stud.
2.
Depress the external latch(es) on the socket housing
side and use a rocking motion to separate the pin and
socket halves. Two-, three-, four- and six-pin Deutsch
connectors have one external latch, while eight- and
twelve-pin connectors have two, both of which must be
pressed simultaneously to separate the connector
halves.
NOTE
With few exceptions, the socket housing can always be found
on the accessory side, while the pin side of the connector is
connected to the wiring harness.
REMOVING/INSTALLING SOCKETS
1.
2.
See Figure B-7. Remove the secondary locking wedge.
Insert the blade of a small screwdriver between the
socket housing and locking wedge inline with the groove
(inline with the pin holes if the groove is absent). Turn the
screwdriver 90 degrees to pop the wedge up.
See Figure B-8. Gently depress terminal latches inside
socket housing and back out sockets through holes in
rear wire seal.
Figure B-7. Depress Terminal Latches/Back Out Pins
NOTE
An ELECTRICAL TERMINAL CRIMP TOOL (Part No. HD39965) is used to install Deutsch pin and socket terminals on
wires. If new terminals must be installed, follow the instructions included with the crimping tool or see Crimping Instructions in this section.
Fit rear wire seal into back of socket housing, if removed.
Grasp socket approximately 1.0 in. (25.4 mm) behind the
contact barrel. Gently push sockets through holes in wire seal
into their respective chambers. Feed socket into chamber
until it “clicks” in place. Verify that socket will not back out of
chamber; a slight tug on the wire will confirm that it is properly
locked in place.
2007 Buell Firebolt: Appendix B
B-5
HOME
d0248x8x
Wire seal
Pin housing
Pin
terminal
Locking wedge
Locking wedge
Internal seal
Latch cover
Alignment grooves
Socket housing
Wire seal
Seal pin
Alignment tabs
External latch
Socket terminal
Figure B-8. 12-pin Deutsch Connector (Exploded View)
3.
●
●
Install internal seal on lip of socket housing, if removed.
Insert tapered end of secondary locking wedge into
socket housing and press down until it snaps in place.
The wedge fits into the center groove within the socket
housing and holds the terminal latches tightly closed.
NOTES
While rectangular wedges do not require a special orientation, the conical secondary locking wedge of the 3-pin
connector must be installed with the arrow pointing
toward the external latch. See Figure B-9.
Pin
housing
Arrow points to
external latch
If the secondary locking wedge does not slide into the
installed position easily, verify that all terminals are fully
installed in the socket housing. The lock indicates when
terminals are not properly installed by not entering its
fully installed position.
REMOVING/INSTALLING PINS
1.
Remove the secondary locking wedge. Use the hooked
end of a stiff piece of mechanics wire a needle nose pliers, or a suitable pick tool (Part No. HD-41475-100). See
Figure B-10.
2.
Gently depress terminal latches inside pin housing and
back out pins through holes in wire seal.
B-6
d0249x3x
2007 Buell Firebolt: Appendix B
Socket
housing
Figure B-9. Depress Terminal Latches/Back Out Pins
HOME
NOTE
An ELECTRICAL TERMINAL CRIMP TOOL (Part No. HD39965) is used to install Deutsch pin and socket terminals on
wires. If new terminals must be installed, see Crimping
Instructions in this section.
3.
4.
●
●
h41475
Fit wire seal into back of pin housing. Grasp crimped pin
approximately 1.0 in. (25.4 mm) behind the contact barrel. Gently push pins through holes in wire seal into their
respective numbered locations. Feed pin into chamber
until it “clicks” in place. Verify that pin will not back out of
chamber; a slight tug on the wire will confirm that it is
properly locked in place.
Figure B-10. Deutsch Connector Pick Tool
(Part No. HD-41475-100)
Insert tapered end of secondary locking wedge into pin
housing and press down until it snaps in place. The
wedge fits in the center groove within the pin housing
and holds the terminal latches tightly closed.
5893
Lock tab
NOTES
While rectangular wedges do not require a special orientation, the conical secondary locking wedge of the 3-pin
connector must be installed with the arrow pointing
toward the external latch. See Figure B-9.
Lock bar
If the secondary locking wedge does not slide into the
installed position easily, verify that all terminals are fully
installed in the pin housing. The lock indicates when terminals are not properly installed by not entering its fully
installed position.
5892
Pin housing
ASSEMBLING/INSTALLING
1.
Insert socket housing into pin housing until it snaps in
place. Two-, three-, four- and six-pin Deutsch connectors
have one external latch on the socket half of the connector. To fit the halves of the connector together, the latch
on the socket side must be aligned with the latch cover
on the pin side.
Attachment clip
For those connectors with two external latches (8-pin
and 12-pin), a different system is used to prevent
improper assembly. Align the tabs on the socket housing
with the grooves on the pin housing. Push the connector
halves together until the latches “click.” If latches do not
click (latch), press on one side of the connector until that
latch engages, then press on the opposite side to
engage the other latch.
●
●
5891
NOTES
Deutsch connectors are color coded for location purposes. Those connectors associated with left side
accessories, such as the front and rear left turn signals,
are gray. All other connectors, including those associated with right side accessories, are black.
If it should become necessary to replace a plug or receptacle, please note that the 8-pin and 12-pin gray and
black connectors are not interchangeable. Since location
of the alignment tabs differ between the black and gray
connectors, plugs or receptacles must be replaced by
those of the same color. If replacing both the socket and
pin halves, then the black may be substituted for the gray,
and vice versa. The socket and pin halves of all other
connectors are interchangeable, that is, the black may be
mated with the gray, since the alignment tabs are absent
and the orientation of the external latch is the same.
Attachment clip installed
Figure B-11. Attachment Clip Installation
2.
See Figure B-11. Fit the attachment clip to the pin housing, if removed. Place large end of slot on attachment
clip over T-stud on frame. Push assembly forward to
engage small end of slot.
2007 Buell Firebolt: Appendix B
B-7
HOME
d0250x8x
Locking bar
1.
Insert contact through middle
hole in locking bar.
2.
Insert stripped lead until it
contacts locking bar.
3.
Close and squeeze crimp tool
4.
Raise locking bar and remove
contact.
Insulation crimp
Core crimp
Figure B-12. Deutsch Crimping Procedure
CRIMPING INSTRUCTIONS
1.
See Figure B-12. Squeeze the handles to cycle the crimp
tool to the fully open position.
2.
Raise locking bar by pushing up on bottom flange. With
the crimp tails facing upward and the rounded side of the
contact barrel resting on the concave split level area of
the crimp tool, insert contact (socket/pin) through middle
hole of locking bar.
3.
B-8
Release locking bar to lock position of contact. If the
crimp tails are slightly out of vertical alignment, the crimp
tool automatically rotates the contact so that the tails
face straight upward. When correctly positioned, the
locking bar fits snugly in the space between the contact
band and the core crimp tails.
2007 Buell Firebolt: Appendix B
4.
Strip lead removing 5/32 in. (4 mm) of insulation. Insert
wires between crimp tails until ends make contact with
locking bar. Verify that wire is positioned so that short
pair of crimp tails squeeze bare wire strands, while long
pair folds over insulation material.
5.
Squeeze handle of crimp tool until tightly closed. Tool
automatically opens when the crimping sequence is
complete. Raise up locking bar and remove contact.
6.
Inspect the quality of the core and insulation crimps. Distortion should be minimal.
HOME
d0251x3x
11
10
9
8
7
6
2-pin connector
5
4
2
1
3
11
10
9
8
7
6
3-pin connector
5
4
2
1
11
3
10
9
8
7
6
5
4-pin connector
4
2
1.
2.
3.
4.
5.
6.
SOCKET SIDE
Socket terminal
Wire seal
Socket housing
External latch
Internal seal
Locking wedge
PIN SIDE
7. Locking wedge
8. Latch cover
9. Pin housing
10. Wire seal
11. Pin terminal
1
3
Figure B-13. 2-Pin, 3-pin and 4-pin Deutsch Connectors
2007 Buell Firebolt: Appendix B
B-9
HOME
PACKARD ELECTRICAL CONNECTORS
GENERAL
From a servicing standpoint, there are two basic types of
Packard electrical connectors, those with pull-to-seat terminals and those with push-to-seat terminals.
Look into the mating end of the connector. If it appears that
the terminal can be extracted from this side, then it is probably the pull-to-seat type.
At least one Packard pull-to-seat terminal can be easily recognized by the presence of a locking ear. The ear engages a
slot in the connector housing and prevents the terminal from
being removed from the wire end side of the connector. The
ear also acts as a strain relief in the event that the wires are
pulled and further inhibits movement of the terminal inside
the chamber. For an example of this type of connector, note
the MAP sensor connector [80].
Unlike most connectors, where the terminals are pulled out
the wire end of the connector, to remove the terminals from
the pull-to-seat connectors, the terminal is pushed out the
mating end of the connector. Once a new terminal is crimped
onto the end of the wire, the wire is pulled to draw the terminal back inside the chamber of the connector housing.
Two types of Packard pull-to-seat electrical connectors are
used. One type has an external latch to lock the pin and
socket halves together, while the other makes use of a wireform. See Figure B-14. The manner in which the terminals
are picked differs between these two types of connectors, as
further described below.
d0258x8x
A
C
Locate tang on latch side of chamber.
B
Push on wire end of lead to
remove terminal.
D
Pivot end of pin to depress tang.
Raise tang and re-install terminal.
Figure B-14. Packard Connectors
B-10
2007 Buell Firebolt: Appendix B
B.3
HOME
PULL-TO-SEAT TERMINALS
Removing External Latch Type
To remove a pull-to-seat terminal from connectors with external latches, proceed as follows:
1.
Remove the connector from the retaining device, if
present.
2.
Bend back the external latch(es) slightly and separate
the pin and socket halves of the connector.
3.
To free a pull-to-seat terminal from the connector housing, first look into the mating end of the connector to find
the locking tang. See A in Figure B-14. The tangs are
always positioned in the middle of the chamber and are
on the same side as the external latch. On those connectors with locking ears, the tang is on the side opposite
the ear.
4.
●
Installing External Latch Type
NOTE
For wire location purposes, alpha characters are stamped
into the socket housings.
1.
To install a terminal back into the chamber of the connector housing, use a thin flat blade, like that on an X-Acto
knife, and carefully bend the tang outward away from the
terminal body. See D in Figure B-14.
2.
Gently pull on the lead at the wire end of the connector to
draw the terminal back into the chamber. A click is heard
when the terminal is properly seated.
3.
Push on the lead to verify that the terminal is locked in
place.
4.
Push the pin and socket halves of the connector together
until the latches “click.”
At a slight angle, gently insert the point of a one inch
safety pin down the middle of the chamber (about 1/8
inch) and pivot the end of the pin toward the terminal
body. When a click is heard, remove the pin and repeat
the procedure. See B in Figure B-14. The click is the
sound of the tang returning to the locked position as it
slips from the point of the pin. Pick at the tang in this
manner until the clicking stops and the pin seems to slide
in at a slightly greater depth than it had previously. This is
an indication that the tang has been depressed.
NOTES
On those terminals that have been extracted on a previous occasion, no clicking sound may be heard when the
pin is pivoted to depress the tang, but proceed as if the
clicking is audible and then push on the wire end of the
lead to check if the terminal is free.
●
When picking multiple terminals, the end of the pin may
become malleable. For best results, continue the procedure with a new safety pin.
5.
Remove the pin and push on the wire end of the lead to
extract the terminal from the mating end of the connector. See C in Figure B-14. If necessary, pull back the conduit and remove the wire seal at the back of the
connector to introduce some slack in the wires.
NOTE
A series of Packard Electrical Terminal Crimp Tools are available to install Packard pin and socket terminals on wires. If
new terminals must be installed, see Crimping Instructions.
2007 Buell Firebolt: Appendix B
B-11
HOME
PUSH-TO-SEAT TERMINALS
Installing Push-to-Seat Terminals
The Packard push-to-seat terminal connectors are Buell Firebolts.
NOTE
For wire location purposes, alpha characters are stamped
onto the secondary locks or onto the wire end of the connector housing.
Removing Push-to-Seat Terminals
Like most connectors, Packard push-to-seat terminals are
pulled out the wire end of the connector. To remove a pushto-seat terminal, proceed as follows:
1.
Remove the connector from the retaining device, if
present.
2.
Bend back the external latch(es) slightly and separate
the pin and socket halves of the connector.
NOTE
Both the Ignition Light/Key Switch and the Main Power connectors are provided with secondary locks. The secondary
lock, which may be molded onto the connector or exist as a
separate piece, aids in terminal retention. Secondary locks
must be opened (or removed) before the terminals can be
extracted from the connector housing.
3.
Open or remove the secondary lock. Bend back the latch
slightly and free one side of the secondary lock, then
repeat the step to release the other side. Rotate the secondary lock outward on hinge to access the terminals in
the chambers of the connector housing.
4.
Looking in the mating end or terminal side of the connector (opposite the secondary lock), take note of the larger
cavity next to each terminal.
5.
Insert the pick (Snap-On TT600-3) into the cavity until it
stops. Pivot the end of the pick toward the terminal to
depress the locking tang. Remove the pick and gently
tug on the wire to pull the terminal from the wire end of
the connector. Repeat the step if the terminal is still
locked in place.
NOTE
A series of Packard Electrical Terminal Crimp Tools are available to install Packard pin and socket terminals on wires. If
new terminals must be installed, see Crimping Instructions.
B-12
2007 Buell Firebolt: Appendix B
1.
To install a terminal back into the chamber of the connector housing, use a thin flat blade, like that on an X-Acto
knife, and carefully bend the tang outward away from the
terminal body.
2.
Push the lead into the chamber at the wire end of the
connector. A click is heard when the terminal is properly
seated.
3.
Gently tug on the wire end to verify that the terminal is
locked in place and will not back out of the chamber.
4.
Close or install the secondary lock. Rotate the hinged
secondary lock inward until tabs fully engage latches on
both sides of connector.
5.
Push the pin and socket halves of the connector together
until the latches “click.”
6.
Install connector on retaining device, if present.
HOME
CRIMPING INSTRUCTIONS
1.
Strip wire lead removing 5/32 in. (4 mm) of insulation.
2.
Compress handles until ratchet automatically opens.
d0259x8x
Tool tip
NOTE
Always perform core crimp before insulation/seal crimp.
3.
See Table B-1. Determine the correct dye or nest for the
core crimp.
NOTE
When the word “TIP” appears in the Crimp Table, use the tip
of the tool specified to perform the core crimp procedure. See
Figure B-15.
4.
Lay the back of the core crimp tails on the appropriate
nest. Be sure the core crimp tails are pointing towards
the forming jaws.
5.
Gently apply pressure to handles of tool until crimpers
slightly secure the core crimp tails.
6.
Insert stripped wire between crimp tails. Verify that wire
is positioned so that short pair of crimp tails squeeze
bare wire strands, while long pair folds over insulation or
seal material.
7.
Squeeze handle of crimp tool until tightly closed. Tool
automatically opens when the crimping sequence is
complete.
8.
Table B-1. Determine the correct dye or nest for the insulation/seal crimp.
9.
Lay the back of the insulation/seal crimp tails on the
appropriate nest. Be sure the insulation/seal crimp tails
are pointing towards the forming jaws.
10. Squeeze handle of crimp tool until tightly closed. Tool
automatically opens when the crimping sequence is
complete.
Packard 115
Packard 271
Figure B-15. Packard Terminal Crimp Tools
Table B-1. Packard Terminal Crimp Tools
PACKARD 115
PACKARD 271
Part No.
SPECIFICATION
HD-38125-8
HD-38125-7
Type of Crimp
Non-sealed
terminals,
butt splices
Non-sealed
terminals
F-G
A-E
Dye/nests
d0260x8x
1
2
3
11. See Figure B-16. Inspect the quality of the core (3) and
insulation/seal (2) crimps. Distortion should be minimal.
1.
2.
3.
Insulation
Insulation crimp
Core crimp
Figure B-16. Inspect Core and Insulation/Seal Crimps
2007 Buell Firebolt: Appendix B
B-13
HOME
ELECTRICAL CONNECTORS
GENERAL
B.4
Connector numbers are listed in [brackets] in this manual.
The following table provides a brief description of the connectors found on the Firebolt XB9R.
Table B-2. Electrical Connector and Location Table
CONNECTOR
COMPONENT(S)
DESCRIPTION
LOCATION
[5]
main fuse
spade terminals
under seat
[7]
tail lamp harness
8-place Multilock
left side under tail section
[10]
ECM (black)
12-place Deutsch
in fairing
[11]
ECM (gray)
12-place Deutsch
in fairing
[14]
cam position sensor
3-place Deutsch
under sprocket cover
[18]
right rear turn signal
2 1-place bullet
under tail section
[19]
left rear turn signal
2 1-place bullet
under tail section
[22]
right hand controls
4-place Multilock
beneath right side of fairing
[24]
left hand controls
8-place Multilock
beneath left side of fairing
[30]
flasher
5-place Amp
in fairing
[31]
right front turn signal
2 1-place bullet
beneath right side of fairing
[31]
left front turn signal
2 1-place bullet
beneath left side of fairing
[33]
ignition switch
4-place Augat
beneath right side of fairing
[38]
headlamp connector
4-place Amp
beneath fairing
[39]
instrument module
20-place Multilock
in fairing
[46]
stator
4-place Deutsch
under sprocket cover
[61]
fuse and diode assembly
spade terminals
right side of fairing
[62]
relay assembly
spade terminals
left side of fairing
[65]
vehicle speed sensor
3-place Deutsch
under sprocket cover
[77]
voltage regulator
2-place Packard
under sprocket cover
[83]
ignition coil
3-place Packard
beneath air cleaner baseplate
[84]
front fuel injector
2-place Packard
beneath air cleaner baseplate
[85]
rear fuel injector
2-place Packard
beneath air cleaner baseplate
[86]
fuel pump
4-place Multilock
left side of rear shock absorber
[88]
throttle position sensor
3-place Packard
beneath air cleaner baseplate
[89]
intake air temperature sensor
2-place Amp
in air cleaner baseplate
[90]
engine temperature sensor
1-place bullet
beneath air cleaner baseplate
[91A]
data link
4-place Deutsch
beneath left side fairing
[93]
tail light
2-place spade
B-14
2007 Buell Firebolt: Appendix B
1-place spade
(ground)
back of tail light
HOME
Table B-2. Electrical Connector and Location Table
CONNECTOR
COMPONENT(S)
DESCRIPTION
LOCATION
[95]
clutch switch
2-place Multilock
underside of clutch lever assembly
[97]
cooling fan
2-place Multilock
behind rear cylinder, under seat
[120]
oil pressure switch
post terminal
crankcase above oil filter
[121]
front brake switch
2-place Multilock
underside of front master cylinder
assembly
[121]
rear brake switch
2-place Multilock
under seat
[122]
horn
2-spade terminals
in fairing
[128]
starter solenoid
spade terminal
top of starter
[131]
neutral switch
1-place bullet
under sprocket cover
[134]
bank angle sensor
6-place Sumitomo
in fairing
[137]
oxygen sensor
1-place Packard
behind rear cylinder head
[161]
Interactive exhaust to actuator
4-place Amp
under air cleaner cover
[164]
Interactive exhaust circuit to ECM
spade terminal
under seat
[165]
Interactive exhaust subharness to
main harness
3-place Deutsch
under seat
[178]
Active intake system to solenoid
2-place Deutsch
under air cleaner cover
[179]
Active intake system to ECM
2-place Deutsch
in fairing
2007 Buell Firebolt: Appendix B
B-15
HOME
INDEX TO WIRING DIAGRAMS
B.5
Table B-3. Wiring Diagrams
DIAGRAM
PAGE
Main harness
B-17
Engine management circuit
B-19
Lighting circuit
B-21
Horn and instruments circuit
B-23
Starting circuit
B-25
Starting and charging circuits
B-27
Component circuits
B-29
B-16
2007 Buell Firebolt: Appendix B
HOME
bd0024af
BRAKE SW
1
2
IGNITION SWITCH WIRING DIAGRAM
KEY POSITION
1
PARK
0
4
3
[121B]
2
RH TURN SIGNAL
O
R/Y
[31B]
1
BN
2
BK
THROTTLE
POSITION
SENSOR
[88B]
1
2
3
[83B]
[88A]
BK/W
V/Y
R/W
1
2
3
[83A]
Y/BE 1
GY 2
BE/O 3
0
1
2
3
ENGINE TEMP SENSOR
IGN.
COIL
[90B]
[90A]
1
PK/Y
LOCK
OFF
1
[137B]
0
0
0
WIRE COLOR
R
R/BK
R
R/GY
WIRE SECT mm
1
1
1
1
+
V/GY
+
IGN
RH CONTROLS
IGN
SW
GY
1 Y
2 BK
GY
W/Y
1 2
[85B]
[33B]
R
R/GY
R/BK
R
BK/R
W/BK
W/BK
GY/O
1 2 3 4 5
STARTER
SOLENOID
BK
[89B]
1 GN
[GRD2]
ECM
(GY)
[11B]
[164B]
(BK)
[10B]
[128A]
BK
IAT
LT.GN/Y 1
BK/W 2
BK
V/BN
O/W
1 2 3 4
1 2 3 4
1
COOLING FAN
[97B]
[97A]
REAR INJECTOR
FRONT INJECTOR
1 2
[84B]
[33A]
1 2 3 4
[22A]
[30B]
1
2
Y/BN
BK/O
BATTERY USER + BATTERY USER +
FLASHER
1
GY
GN/GY
CONNECTING
[137A]
OXYGEN SENSOR
0
LOCK
ON
GROUND
5V SENSOR POWER
THROTTLE POS SENSOR
CAMSHAFT POS SENSOR
OXYGEN SENSOR
KEEP ALIVE
FAN CONTROL
SENSOR GROUND
VEHICLE SPEED SENSOR
ENGINE TEMP INPUT
AIR TEMP INPUT
SERIAL DATA RECEIVE
SERIAL DATA TRANSMIT
1
2
3
4
5
6
7
8
9
10
11
12
R/W
V/Y
GN/W
V/GY
Y
BK/O
BK/W
W
PK/Y
LT.GN/Y
LT.GN/R
V/R
ACTIVE MUFFLER CONTROL
1
W
SWITCHED IGNITION
SYSTEM GROUND A
FUEL PUMP OUTPUT
CHECK ENGINE LAMP
INJECTOR FRONT OUTPUT
FRONT COIL PRIMARY
REAR COIL PRIMARY
INJECTOR REAR OUTPUT
ACTIVE MUFFLER FEEDBACK
BANK ANGLE SENSOR
SYSTEM GROUND B
TACHOMETER OUTPUT
1
2
3
4
5
6
7
8
9
10
11
12
BATTERY
R/Y
R
O 1
W 2
TN/V 3
ACTIVE MUFFLER
CONTROL SUB HARNESS
[165A]
DYNO
LOOP
Y/BE
FUSE & DIODE ASSY
GY
BK
BN/Y
BK/Y
W/Y
Y/BE
BE/O
GN/GY
TN/V
LT.GN/GY
BK
PK
BK
8
2
10
GY/O
11
R/GY
12
BK
19
Y/BN
15 AMP.
10 AMP.
6
O/W
15 AMP.
SPARE
13
R
22
R/BK
R
R
[122B]
15 AMP.
23
17
KEY SWITCH
24
BK
Y
BE
BE
Y/R
BK
BN/Y
GY
15 AMP.
18
1
2
3 TAIL HARNESS
4 [7A]
5
6
7
8
FUEL PUMP
10 AMP.
16
LIGHTS
BK
10 AMP.
14
ECM
BK
BN
O/W
V
R/Y
R/BK
5
20
R/Y
O
[121B]
10 AMP.
4
ACCESSORY
BK
Y/BK
1
2
[121A]
R/BK
COOLING FAN
IGNITION
BK
[122A]
R/Y 1
O 2
TN/LT.GN
3
9
O
O
R
[GRD3]
HORN
1
2
FOOT BRAKE SW
BRAKE/HORN/MUFFLER 10 AMP.
[GRD1]
BK
[61B]
DIODE
TN/Y
TN/Y
SPARE
1
2
[128B]
J-FUSE ASSY
[5A]
1
2
R
A
B
C
D
MTR
A Y/R
B BK
C BN/Y
D GY
[86B]
[86A]
LOW
FUEL
SENSOR
NEUTRAL SW
1
TN/Y
1
[131B]
[131A]
[39B]
IGNITION
86 1
85 9
30 5
87A 3
87 4
START
RELAY CENTER
86 10
85 2
30 6
87A 8
87 7
KEY SW
SPEEDOMETER
[39A]
1
2
3
R/W 4
LT.GN/GY 5
BK/W 6
[62B]
86
85
30
87A
87
11
19
15
13
14
W/BK
W/BK
BK
GY/O
GY/O
GY
BK/R
TN/LT.GN
R/BK
R/BK
GN
R/BK
R/BK
BK
R
[65B]
BE
W
Y/BK
V/BN
V
BN
O
IGNITION
GROUND
TACH IN
LFW
VSS IN
BATTERY
NEUTRAL
LEFT TURN
RIGHT TURN
HIGH BEAM
CHECK ENGINE
OIL PRESSURE
7
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
[24A]
1 2 3 4 5 6 7 8
BANK ANGLE SENSOR
LH CONTROLS
[134B]
HEADLAMP
O/W
W
BE
BK
[65A]
CMP
1
2
3
4
R/W A
GN/W B
BK/W C
[14B]
A R/W
B GN/W
C BK/W
[14A]
[38A]
V
1
BK 2
LH TURN SIGNAL
[31B]
LT.GN/R
BK
V/R
GY
1 2
CLUTCH SW
VOLTAGE REGULATOR
DATA LINK
TN/LT.GN
BK
O/W
BK
PK
Y/R
W
R
TN/Y
V
BN
W
BK/Y
GN/Y
VSS
R/W A A R
W B B W
BK/W C C BK
[95B]
BK 1
R 2
1
2 [91A]
3
4
1
1
GN/Y
OIL PRESSURE SW
[77B]
[120B]
GN/Y
[120A]
R/BK
A=
MALE
B=
FEMALE
2007 XB Firebolt Main Harness
2007 Buell Firebolt: Electrical
B-17
HOME
2007 XB Firebolt Main Harness
B-18
2007 Buell Firebolt: Electrical
2007 XB Firebolt Main Harness
HOME
bd0022af
[83B]
IGNITION SWITCH WIRING DIAGRAM
KEY POSITION
1
PARK
0
3
[88B]
2
4
THROTTLE
POSITION
SENSOR
0
LOCK
1
2
3
Y/BE 1
GY 2
BE/O 3
[88A]
BK/W
V/Y
R/W
1
2
3
OFF
[83A]
1
2
3
ENGINE TEMP SENSOR
IGN.
COIL
[90B]
PK/Y 1
[137B]
ON
0
0
0
0
WIRE COLOR
R
R/BK
R
R/GY
WIRE SECT mm
1
1
1
1
OXYGEN SENSOR
V/GY 1
Y/BN 1
BK/O 2
+
IGN
RH CONTROLS
IGN
SW
FRONT INJECTOR
[33A]
R
[85B]
[84B]
[97A]
BK
IAT
LT.GN/Y 1
BK/W 2
[33B]
1 Y
2 BK
[97B]
1 2
GY
W/Y
1 2 3 4
1 2 3 4
R/BK
R
[22A]
W/BK
W/BK
GY/O
1 2 3 4
[137A]
1 GY
COOLING FAN
REAR INJECTOR
1 2
GY
GN/GY
BATTERY USER + BATTERY USER +
LOCK
CONNECTING
+
[90A]
1
[GRD2]
[89B]
ECM
ACTIVE MUFFLER CONTROL
1
W
SWITCHED IGNITION
SYSTEM GROUND A
FUEL PUMP OUTPUT
(BK)
CHECK ENGINE LAMP
[10B]
INJECTOR FRONT OUTPUT
FRONT COIL PRIMARY
REAR COIL PRIMARY
INJECTOR REAR OUTPUT
ACTIVE MUFFLER FEEDBACK
BANK ANGLE SENSOR
SYSTEM GROUND B
TACHOMETER OUTPUT
1
2
3
4
5
6
7
8
9
10
11
12
GY
BK
BN/Y
BK/Y
W/Y
Y/BE
BE/O
GN/GY
TN/V
LT.GN/GY
BK
(GY)
[11B]
[164B]
J-FUSE ASSY
R/Y 1
R 2
[5A]
O 1
W 2
TN/V 3
O
W
TN/V
1
2
3
[165A]
DYNO
LOOP
Y/BE
FUSE & DIODE ASSY
[61B]
MUFFLER VALVE
ACTUATOR
1
2
3
DC
4
MOTOR
DIODE
8
2
TN/LT.GN
BRAKE/HORN/MUFFLER 10 AMP
3
9
R/BK
O
COOLING FAN 10 AMP
4
Y/BN
R 10
IGNITION 15 AMP
5
R/BK
GY/O 11
TN/Y
TN/Y
BK
[GRD1]
BK
[GRD3]
[165B]
ACTIVE MUFFLER SUB HARNESS
V bat
1 O
2 BK
3 W
4 TN/V
POSITION
SENSOR
CONTROL SIGNAL
R/W
V/Y
GN/W
V/GY
Y
BK/O
BK/W
W
PK/Y
LT.GN/Y
LT.GN/R
V/R
HALL SENSOR
1
2
3
4
5
6
7
8
9
10
11
12
CONTROL ELECTRONICS
5V SENSOR POWER
THROTTLE POS SENSOR
CAMSHAFT POS SENSOR
OXYGEN SENSOR
KEEP ALIVE
FAN CONTROL
SENSOR GROUND
VEHICLE SPEED SENSOR
ENGINE TEMP INPUT
AIR TEMP INPUT
SERIAL DATA RECEIVE
SERIAL DATA TRANSMIT
GROUND
[161A]
[161B]
XB9 models do not have
the circuitry for the active
muffler.
ECM
R
R
R
22
10 AMP
16
FUEL PUMP
Y
A
BK B
BN/Y C
GY D
KEY SWITCH 15 AMP
24
18 R
MTR
A
B BK
C BN/Y
D GY
LOW
FUEL
SENSOR
[86B]
[86A]
NEUTRAL SW
TN/Y 1
1
[131B]
[131A]
VSS
W
[39B]
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
1
2
3
R/W 4
LT.GN/GY 5
BK/W 6
RELAY CENTER
IGNITION
GROUND
TACH IN
LFW
VSS IN
[62B]
86
85
30
87A
87
1
9
5
3
4
W/BK
W/BK
BK
GY/O
GY/O
GY
1
2
3
BK 4
BANK ANGLE SENSOR
[134B]
[39A]
KEY SW
CLUTCH SW
11
19
15
13
14
R/W A
GN/W B
BK/W C
[14B]
A R/W
B GN/W
C BK/W
[14A]
[38A]
SPEEDOMETER
86
85
30
87A
87
[65A]
CMP
HEADLAMP
TN/LT.GN
BK
IGNITION
BATTERY
NEUTRAL
LEFT TURN
RIGHT TURN
HIGH BEAM
CHECK ENGINE
OIL PRESSURE
A R
B W
C BK
[65B]
BK
BK/Y
R
TN/Y
R/W A
W B
BK/W C
DATA LINK
[95B]
1 2
R/BK
R/BK
BK
R
R/BK
LT.GN/R 1
BK 2
V/R 3
GY 4
[91A]
A=
MALE
B=
FEMALE
2007 XB Firebolt Engine Management Circuit
2007 Buell Firebolt: Electrical
B-19
HOME
2007 XB Firebolt Engine Management Circuit
B-20
2007 Buell Firebolt: Electrical
2007 XB Firebolt Engine Management Circuit
HOME
bd0021af
BRAKE SW
IGNITION SWITCH WIRING DIAGRAM
KEY POSITION
1
3
4
2
PARK
0
0
[121B]
1
2
RH TURN SIGNAL
O
R/Y
[31B]
1
BN
2
BK
LOCK
OFF
0
0
0
0
WIRE COLOR
R
R/BK
R
R/GY
1
1
1
1
WIRE SECT mm
CONNECTING
+
+
IGN
SW
BATTERY USER + BATTERY USER +
IGN
LOCK
ON
[33A]
FLASHER
BK
[33B]
BK
[30B]
V/BN
O/W
1 2 3 4 5
R
R
R/GY
1 2 3 4
1 2 3 4
[GRD2]
R/Y
R
J-FUSE ASSY
1
2
[5A]
FOOT BRAKE SW
FUSE & DIODE ASSY
R/Y
O
[61B]
BRAKE/HORN/MUFFLER 10 AMP
9
3
R/BK
O
BK
1
2
1
2
[121B]
[121A]
[GRD3]
R/GY
LIGHTS
O/W
BK
R
V
BN
W
R/BK
R
R
23
15 AMP
17
1
2
3
4
5
6
7
8
TAIL HARNESS
[7A]
BE
BE
24
18 R
KEY SWITCH 15 AMP
[39B]
V/BN
V
BN
O
BE
W
IGNITION
GROUND
TACH IN
LFW
VSS IN
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
BATTERY
NEUTRAL
LEFT TURN
RIGHT TURN
HIGH BEAM
CHECK ENGINE
OIL PRESSURE
BK
BN
O/W
V
R/Y
ACCESSORY 10 AMP
12
6
O/W
R/Y
O
1 2 3 4 5 6 7 8
LH CONTROLS
[62B]
START
10
2
6
8
7
KEY SW
[39A]
86
85
30
87A
87
86
85
30
87A
87
11
19
15
13
14
HEADLAMP
O/W
W
BE
BK
1
2
3
4
[38A]
RELAY CENTER
SPEEDOMETER
[24A]
V
1
LH TURN SIGNAL
BK 2
R/BK
[31B]
R/BK
2007 XB Firebolt Lighting Circuit
2007 Buell Firebolt: Electrical
B-21
HOME
2007 XB Firebolt Lighting Circuit
B-22
2007 Buell Firebolt: Electrical
2007 XB Firebolt Lighting Circuit
HOME
bd0020af
IGNITION SWITCH WIRING DIAGRAM
IGN
SW
1
PARK
0
3
2
4
0
LOCK
IGN
LOCK
OFF
[33A]
R
1 2 3 4
1 2 3 4
R
R/GY
KEY POSITION
ON
0
0
0
0
WIRE COLOR
R
R/BK
R
R/GY
WIRE SECT mm
1
1
1
1
[33B]
CONNECTING
+
BATTERY USER +
BK
+
BATTERY USER +
[GRD2]
ECM
1
5V SENSOR POWER
2
THROTTLE POS SENSOR
CAMSHAFT POS SENSOR 3
OXYGEN SENSOR 4
KEEP ALIVE 5
FAN CONTROL 6
SENSOR GROUND 7
VEHICLE SPEED SENSOR 8
ENGINE TEMP INPUT 9
AIR TEMP INPUT 10
SERIAL DATA RECEIVE 11
SERIAL DATA TRANSMIT 12
(GY)
[11B]
R/W
R/Y
R
(BK)
[10B]
[5A]
BK/W
W
[61B]
FUSE & DIODE ASSY
SWITCHED IGNITION 1
SYSTEM GROUND A 2
FUEL PUMP OUTPUT 3
CHECK ENGINE LAMP 4
INJECTOR FRONT OUTPUT 5
FRONT COIL PRIMARY 6
REAR COIL PRIMARY 7
INJECTOR REAR OUTPUT 8
ACTIVE MUFFLER FEEDBACK 9
BANK ANGLE SENSOR 10
SYSTEM GROUND B 11
TACHOMETER OUTPUT 12
J-FUSE ASSY
1
2
DIODE
TN/Y
TN/Y
GY
BK
BK
8
2
TN/LT.GN
9
3
R/BK
[GRD1]
BK
O
BRAKE/HORN/MUFFLER
10AMP
[GRD3]
ACCESSORY 10AMP
12
6
O/W
R/GY
BK
PK
HORN
1
2
[122A]
1
2
BK
Y/BK
FUEL PUMP
[122B]
Y/R A
BK B
C
GY D
KEY SWITCH 15AMP
24
18
R
R
R
A
B
C
D
MTR
Y/R
BK
LOW
FUEL
SENSOR
GY
[86A]
[86B]
NEUTRAL SW
1
TN/Y
1
[131A]
[131B]
VSS
A
B
C
A
B
C
R
W
BK
[65B]
O/W
BK
PK
Y/R
W
GN/Y
R
TN/Y
R/W
W
BK/W
[65A]
[39B]
RELAY CENTER
O
Y/BK
IGNITION
GROUND
TACH IN
LFW
VSS IN
BATTERY
NEUTRAL
LEFT TURN
RIGHT TURN
HIGH BEAM
CHECK ENGINE
OIL PRESSURE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
[24A]
1 2 3 4 5 6 7 8
[62B]
LH CONTROLS
START
[39A]
86 10
2
85
6
30
87A 8
7
87
KEY SW
SPEEDOMETER
86
85
30
87A
87
11
19
15
13
14
TN/LT.GN
1
1
GN/Y
[120B]
R/BK
GN/Y
OIL PRESSURE SW
[120A]
A=
MALE
B=
FEMALE
2007 XB Firebolt Horn & Instruments Circuit
2007 Buell Firebolt: Electrical
B-23
HOME
2007 XB Firebolt Horn & Instruments Circuit
B-24
2007 Buell Firebolt: Electrical
2007 XB Firebolt Horn & Instruments Circuit
HOME
bd0023af
IGNITION SWITCH WIRING DIAGRAM
IGN
SW
IGN
LOCK
RH CONTROLS
[33A]
R/BK
R
1 2 3 4
1 2 3 4
R
BK/R
W/BK
W/BK
GY/O
1
PARK
0
3
4
2
0
LOCK
1 2 3 4
[22A]
KEY POSITION
OFF
ON
0
0
0
0
WIRE COLOR
R
R/BK
R
R/GY
WIRE SECT mm
1
[33B]
1
+
CONNECTING
BATTERY USER +
1
STARTER
SOLENOID
BK
1
[128A]
BK
+
BATTERY USER +
1 GN
[GRD2]
J-FUSE ASSY
[5A]
DIODE
TN/Y
8
R
[128B]
[61B]
FUSE & DIODE ASSY
GY/O
GROUND
1
2
R/Y
R
2
11
TN/LT.GN
IGNITION 15AMP
5
R/BK
KEY SWITCH 15AMP
24
18
R
NEUTRAL SW
TN/Y
1
[131B]
1
[131A]
[62B]
IGNITION
86 10
2
85
6
30
87A 8
7
87
KEY SW
START
1
9
5
3
4
86
85
30
87A
87
86
85
30
87A
87
11
19
15
13
14
W/BK
W/BK
BK
GY/O
GY/O
TN/LT.GN
BK
RELAY CENTER
BK/R
TN/LT.GN
R/BK
GN
R/BK
[95B]
1 2
CLUTCH SW
BK
R
R/BK
A=
MALE
B=
FEMALE
2007 XB Firebolt Starting Circuit
2007 Buell Firebolt: Electrical
B-25
HOME
2007 XB Firebolt Starting Circuit
B-26
2007 Buell Firebolt: Electrical
2007 XB Firebolt Starting Circuit
HOME
bd0018xx
BKBK
Battery Cable
[128A]
Battery
Starter Motor
BK
BK
[GRD2]
To J-Fuse Assembly
R/Y
R/Y
1
R
R
Maxifuse
30A
2
[5A]
To Voltage Regulator
BK
BK
1
1
R
BK
2
2
[77B]
[77A]
Voltage
Regulator
BK
BK
BK
A=
B=
Male
Female
Stator
H-D 3-Phase
1
2
3
4
[46A]
1
2
3
4
[46B]
2007 XB Firebolt Starting & Charging Circuit
2007 Buell Firebolt: Electrical
B-27
HOME
2007 XB Firebolt Starting & Charging Circuit
B-28
2007 Buell Firebolt: Electrical
2007 XB Firebolt Starting & Charging Circuit
HOME
bd0019af
BATTERY CABLE
[7B]
BK
TO MAIN HARNESS
[128A]
FRONT TURN SIGNALS
BATTERY
LH TURN SIGNALS
BE 1
BK 2
[31A]
1
2
BRAKE SW.
V
BK
[121A]
1 2
MAIN HARNESS
RH TURN SIGNALS
BK 2
BE 1
[31A]
2
1
YH350.02A8
STARTER
MOTOR
BK
[31B]
TAIL LAMP/REAR TURNING LIGHTS
[GRD2]
LH TURN SIGNAL
RH CONTROLS
BK
BN
BK/R
W/BK
W/BK
GY
[31B]
1
2
3
4
[19A]
[22B]
1
2
R/Y
R
30A MAXIFUSE
O/W
W
Y
BK
1
2
1
2
[77B]
1
V
BK
2
2
BK
1
2
1
2
O/W
R/Y
1
1
BK
BN
1
1
BN
BK
2
2
BK
[93B]
TAIL LIGHT
[77A]
HORN
RH TURN SIGNAL
HEADLIGHT
SUB-HARNESS(ES)
H3-55W
HI AND LO
BEAMS
1
2
Y
BK
1
2
W
BK
Y
BE
W
Y/BK
BE/W
V
BN
O
CLUTCH SW.
[95A] 1 2
[38HA]
[24B]
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
VOLTAGE
REGULATOR
1 2
LH CONTROLS
[38LA]
POSITION
LAMPS
1
[93A]
TO VOLTAGE REGULATOR
BK
R
TO MAIN HARNESS
[19B]
V
TO J-FUSE ASSY
[5A]
1
2
3
4
BK
BN
O/W
V
R/Y
1
2
3
4
5
6
7
8
STARTER
SOLENOID
BK
[122B]
Y/BK
Y/BK
VEHICLE SPEED SENSOR
STATOR
1
2
3
4
(HD 3-PHASE)
[24A]
1 O/W
2 BK
(HDI ONLY)
[29A]
[18B]
[18A]
[46A]
[65A]
1
2
3
4
[46B]
[29B]
R A
W B
BK C
1 O/W
2 BK
MUFFLER VALVE ACTUATOR
POSITION
SENSOR
MTR
[161A]
CONTROL ELECTRONICS
1 2 3 4
FRONT INJECTOR
REAR INJECTOR
MUFFLER ACTUATOR
1 2 3 4
O
BK
W
TN/V
SUB-HARNESS
Y0206.1AA
FLASHER
[30A]
[161B]
[165B]
OIL PRESSURE SWITCH
[84A]
GN/Y 1
[85A]
BK
[84B]
1 2
1 2
[85B]
GY
GN/GY
1 2
1 2
1 2 3 4 5
V/BN
O/W
[30B]
4
GY
W/Y
1 2
GN/Y
1
[120B]
TO MAIN HARNESS
[120A]
1
2
3
O
W
TN/V
FUEL PUMP
ENGINE TEMP SENSOR
PK/Y 1
1
[90B]
[90A]
MAIN HARNESS
MTR
A
B
C
D
Y/R
BK
BN/Y
GY
[86B]
[134B]
LOW
FUEL
SENSOR
[89A]
1 2
1 2
[89B]
INTAKE AIR TEMP
LT.GN/Y
BK/W
BANK ANGLE SENSOR
1 1
2 2
3 3
UP
R/W 4 4
LT.GN/GY 5 5
BK/W 6 6
[134A]
A=
MALE
B=
FEMALE
2007 XB Firebolt Component Circuits
2007 Buell Firebolt: Electrical
B-29
HOME
2007 XB Firebolt Component Circuits
B-30
2007 Buell Firebolt: Electrical
2007 XB Firebolt Component Circuits