COOPER LIGHTING - SURE-LITES ®
DESCRIPTION
The All Pro Series emergency light (AP2SQ) is the ideal choice when an
affordable unit is required for general purpose applications. Its styling
and designer finish enables it to blend with any decor. The housing and
mounting plate employ snap- fit construction to further improve the
installation time. Both lighting heads are fully adjustable, insuring that
light can be put where it is needed.
Type
Catalog #
Project
Date
Comments
Prepared by
S P E C I F I C AT I O N F E AT U R E S
E l e c t ri c a l
- Dual Voltage Input 120/277
VAC, 60 Hz
- Line-latching
- Brownout circuit
- Low Voltage Disconnect
- Overload/Short Circuit
Protection
- Test Switch/Power connector
facilitates installation
H o u s i n g C o n s t ru c t i o n
- All components are injectionmolded, color stable, high
impact thermoplastic material
- Designer textured finish
standard
- Components are of snap-fit
construction to facilitate under
5-minute installation
- NEC/OSHA
- Most State and Local Codes
- Reinforcing ribs throughout to
provide maximum strength
- Suitable for wall or ceiling
mount applications
- Universal J-box mounting
pattern
- Keyhole mounting slots
Wa rra n t y
- Exit: 1 year
- Battery: 5 year, pro-rata
H e a d / L a m p Da t a
- Two heads standard
- Square Head Type Design
- Glare-free Lens
- Fully adjustable lamp
housing
- High impact thermoplastic
- Matches housing finish
B a tte r y
- Sealed Lead Calcium,
recombination
- Maintenance-free, long-life
- Full recharge time: 24 hrs
(max.)
- Polarized battery terminals
AP2SQ
SERIES
Code Compliance
- UL 924 Listed
- ETL Damp Location
- Life Safety NFPA 101
6”
[152mm]
when
extended
12 1/2”
[308mm]
SEALED LEAD
C A L C I U M B AT T E RY
4”
[102mm]
5”
[127mm]
E M E R G E N CY L I G H T I N G
5”
[127mm]
16”
[440mm]
2 3/8”
[60mm]
E L E C T R I C A L R AT I N G S
R a t e d W a t t a g e to 87 1/2% of Rated D.C. Voltage
Model
DC Voltage
1 1/2 Hours
AP2SQ
6
10.8
2 Hours
7.2
L a m p I n fo r m a t i o n
Type
Wattage
Number
Incandescent
5.4
29-121
ORDERING INFORMATION
Family
AP2SQ
Housing Finish
__=White
Accessories
1
Protective Housing
WG1=Wire Guard
VS1=Polycarbonate Vandal Shield
VS1WP=Polycarbonate Vandal Shield - Weather Resistant
E N E R G Y D ATA
Model AP2SQ
Input Current (Max.):
Notes:
1 Order separately.
120V = .04A
277V = .02A
Specifications and dimensions subject to change without notice.
Consult your representative for additional options and finishes.
ADX061689 pc
2011-05-10 14:50:05
A P 2 S Q SERIES
T E C H N I C A L DATA
economical. A labor efficient AC-activated load
switch prevents the lamps from turning on
during installation to a non-energized AC circuit.
Linelatching eliminates the need for a
contractor’s return to a job site to connect the
batteries when the building’s main power is
permanently turned on.
L ow Vo l t a ge D i s c o n n e c t
Designed specifically for emergency lighting
applications the square head type design
ensures optimum glare free trapezoidal light
distribution along with horizontal and vertical
adjustment by rotating the lens within the
housing.
H o u s i n g C o n s t ru c t i o n
S o l i d - S t a te C h a rge r
Te s t Sw i t ch / Powe r I n d i c a to r L i g h t
Rugged, durable, injection molded
thermoplastic materials are used throughout the
All Pro Series Emergency Lighting Units. All
structural components are designed with
reinforcing ribs to add additional rigidity and to
maximize structural integrity. These materials
are impact and scratch resistant, and they have
been UV stabilized to resist discoloration due to
age and ultraviolet radiation. All components
are designed to be of snap-fit construction - no
mechanical fasteners - to facilitate installation in
under 5-minutes. The mounting plate has
keyhole mounting slots and a universal
mounting pattern for quick, efficient installation.
Any components required for installation
(wirenuts, wire leads, etc.) are all included with
each unit. All AP2SQ Series Units are suitable
for wall or ceiling mount applications.
Supplied with a 120/277 VAC, voltage regulated
solid-state charger. Immediately upon
restoration of AC current after a power failure,
the charger provides a high charge rate. The
charge circuit reacts to the condition of the
battery and alters the rate of charge in order to
maintain peak battery capacity and maximize
battery life. Solidstate construction recharges
the battery following a power failure in
accordance with UL 924.
A test switch permits the activation of the
emergency circuit for a complete operational
system check. The Power Indicator Light
provides assurance that the AC power is on.
Lamps
L i n e - L a t ch e d
When the battery’s terminal voltage falls below
80% of the rated voltage, the low voltage
circuitry disconnects the lighting load. The
disconnect remains in effect until normal utility
power is restored, preventing deep battery
discharge.
S e a l e d L e a d C a l c i u m B a tte r y
The fully sealed, long life, maintenance free lead
calcium battery is ideal for emergency lighting
applications. These recombinant cycle batteries
typically provide 5 years of life and may be
operated in any position.
B row n o u t C i rc u i t
The brownout circuit in All Pro Emergency units
monitor the flow of AC current to the unit and
activates the emergency lighting system when a
predetermined reduction of AC power occurs.
This dip in voltage will cause most ballasted
fixtures to extinguish causing loss of normal
lighting even though a total power failure has
not occurred.
Wa rra n t y
All Pro Emergency units are backed by a firm
one year warranty against defect in material and
workmanship (excluding lamps). Maintenance
free, long life, sealed lead calcium batteries
carry a five-year pro-rata warranty.
All Pro Emergency’s line-latched electronic
circuitry makes installation easy and
Specifications and dimensions subject to change without notice.
Sure-Lites • Customer First Center • 1121 Highway 74 South • Peachtree City, GA 30269 • TEL 770.486.4800 • FAX 770.486.4801
ADX061689 pc
2011-05-10 14:50:05
2011-05-10 14:05:38