w w w. k i n e t i c s n o i s e . c o m
ABOUT KINETICS NOISE CONTROL
Kinetics Noise Control has been engineering and manufacturing vibration
isolation and noise control products and systems for over 40 years. We
pioneered the use of pre-compressed molded fiberglass for vibration isolation.
Throughout the years, we have developed and refined a complete line of noise
and vibration control products. In addition to the vibration isolation products
illustrated in the brochure, we also offer complete designed pipe riser isolation
systems, computer-assisted seismic design, engineered floating floor systems
for control of airborne and impact noise, and a complete selection of barriers,
absorbers and damping materials. Kinetics offers the engineering expertise,
laboratory, and field testing capabilities to work with you and your acoustical
consultant to develop a solution to your specific noise control problem.
United States
6300 Irelan Pl
P.O. Box 655
Dublin, Ohio 43017
800.959.1229
ph. 614.889.0480
fx. 614.889.0540
Canada
1720 Meyerside Drive
Mississauga, Ontario
L5T 1A3
ph. 905.670.4922
fx. 905.670.1698
www.kineticsnoise.com
sales@kineticsnoise.com
Vibration Products 3/04
FREE-STANDING SPRING ISOLATORS
RESTRAINED SPRING ISOLATORS
ROOFTOP ISOLATION CURBS
Kinetics Model FDS Spring
Isolators
unhoused,
are
free-standing,
large
diameter
laterally stable steel springs
Kinetics Model KSR Roof Rails are pre-engineered,
contained in an upper load
spring-supported isolation systems designed for curb-
plate/leveling assembly and
supported rooftop equipment. The KSR rails are easy-
lower load plate/noise pad
to-install vibration isolation systems that provide an
assembly, for control of high fre-
airtight and watertight seal between the rooftop
quency vibration. They are also
mechanical equipment and the roof curb. KSR rails are
available as an all-welded unit
available in 1" and 2" deflection.
spring isolators are designed for
spring deflection ranges from 0.71" to 4.00” with load
capacity up to 23,200 lbs. FDS spring isolators are
recommended for the isolation of floor-mounted refrigeration compressors, pumps, packaged air handlers, airconditioning equipment, centrifugal and axial fans, and
internal combustion engines. For equipment subject to
weight change or high wind loads, see Restrained
Spring Isolators.
HOUSED SPRING ISOLATORS
Kinetics Model FLS Restrained Spring Isolators are large
diameter, laterally stable steel springs assembled into a
welded steel housing designed to limit vertical movement of
the isolated equipment if equipment weights are reduced or
Kinetics Model KSCR
if the equipment is subjected to large external forces. The
Affordable...easy-to-install...all-in-one roof curb AND
spring elements are complete with high frequency vibration
vibration isolation for under 20-ton packaged rooftop
control noise pads and an adjustable top load plate with lev-
units! Standard features include:
eling bolts. They are available with deflections 0.71" to 4.00"
• Internal seismic restraint
for loads up to 23,200 lbs. The FLS isolators are recom-
• 100 mph wind restraint
mended for the isolation and restraint of large fluid-carrying
• 1" or 2" deflection springs
equipment such as boilers, chillers, and cooling towers, or
• Supply and return flexible connector support hardware
for equipment subjected to high wind loads.
• EPDM airtight and weather-tight seal for non-ducted
800.959.1229
w w w. k i n e t i c s n o i s e . c o m
for bolt-down applications. FDS
applications
• High profile, non-interference aluminum equipment rail
• Accessible, interchangeable springs
Kinetics Model SL and SM Spring Isolators are high
Kinetics Model ESR
deflection stable springs assembled into telescoping
Heavy-duty, complete vibration isolation curb for the
aluminum or cast iron housings,
BIG rooftop unit jobs!
complete with 1/4"
noise pads bonded to the lower load surface. Adjusting
Standard Features include:
and leveling bolts are part of the top housings. Model
• 1 g seismic restraint & 125 mph wind restraint
SM spring isolators are designed with an adjustable
snubbing feature to reduce movement during start-up
Kinetics Model FRS Spring Isolators are light capacity,
and shutdown. Model SM isolators are available with
vertically restrained isolators with rated deflections from
deflections to 1.84" in capacities from 250 to 3,000 lbs.
0.71" to 2.00" in capacities up to 3,500 lbs. FRS isolators are
Model SL isolators are available with the same deflec-
recommended for the isolation and restraint of lightweight
tion ranges and capacities from 35 to 3,500 lbs. Kinetics
mechanical equipment subject to high wind loads or equip-
Model SL and SM spring isolators are typically used to
ment subject to weight change. FRS isolators can also be
isolate mechanical equipment subject to freguent start-
used for support of vertical pipe risers where isolation is
up and shutdown such as compressors and engine
required yet vertical motion controlled. The FRS can be used
generators.
in outdoor applications.
2
• Access ports for each isolator to inspect, level, or
change springs after equipment placement
• Up to 4" deflection, powder-coated steel springs with
50% overload capacity
• High-frequency noise isolation pads
• Environmentally inert elastomeric seal for an air- and
watertight closure between the curb and isolation rail
• Supply and return duct support hardware
• Structural steel curb with wood nailer.
7
ISOLATION BASES
SESIMIC RESTRAINT ISOLATORS AND SNUBBERS
Kinetics Model CIB-H & L Inertia Base Frames are
pre-engineered welded steel pouring frames with
welded-in concrete reinforcement, equipment mounting
bolts, and vibration isolator brackets. The CIB bases are
designed to add mass to the rotating equipment in addition to rigidity and support for vibration isolation. CIB
bases are typically used with reciprocating compressors,
large chillers, compressors, fans, and pumps, and can
w w w. k i n e t i c s n o i s e . c o m
mount-type isolation.
Kinetics Model FLSS Seismic Control Restrained Spring
Kinetics Model FHS Seismic Control Restrained Spring
Vibration Isolators, in addition to the same features of our
Isolators meet specifications for Kinetics Model FDS iso-
Model FLS Restrained Spring Vibration Isolators, offer
lators and include a steel housing assembly to limit both
additional seismic restraint capabilities. The seismic
lateral and vertical movement of the supported equipment
capacity ratings for isolators are determined at Kinetics
during an earthquake without degrading the vibration iso-
Kinetics Model SFB Welded Structural Frame Bases are
by statically loading sample isolators in the vertical, both
lation of the spring during normal equipment operating
individually designed and fabricated to provide rigidity and
horizontal, and in the vertical and horizontal axis simulta-
conditions.
support to mechanical equipment.
neously until failure. The resulting maximum limits define
the restraint capacity envelope. Appropriate Model FLSS
and FHS Isolators are selected by first determining seismic force requirements computed at each isolator using
specific job specification data and local code requirements and then comparing those requirements to the
Kinetics Model SBB Structural Beam Bases are com-
capabilities as defined by the restraint capacity envelope.
posed up of two (2) structural members used to support
Standard FHS isolators incorporate a steel housing which
encloses a neoprene snubber. Depending on the load and
seismic zone, an optional steel spreader plate may be
applied to distribute the load among concrete anchors. A
neoprene pad fitted in series with the spring is provided.
Equipment attachment is by way of a bolt screwed downward through the equipment foot. Removal of the isolator
for servicing can be easily accomplished as the isolator is
equipment that does not require a unitary base, such as
not fitted with a protruding stud. In conformance with all
small close-coupled pumps, fans, and air handlers. The
current building code standards, the restraining system is
structural beams provide rigidity to the equipment and
designed to withstand a minimum 1.0 g acceleration force.
accommodate the installation of vibration isolation.
Motion is limited to approximately 0.2" in any direction.
AIR MOUNTS
Kinetics Seismic Cable Restraints are designed to pro-
6
Kinetics Model KAM and CAM Air Isolators are pneumatic, elas-
vide seismic restraint capacity in excess of the new build-
tomeric vibration mounts. The CAM is available in four (4) sizes sup-
ing codes and reduce costly field installation time. The
porting loads up to 7,500 lbs. The KAM is available in seven (7) sizes
engineered brackets and cable assemblies are multi func-
Kinetics
with capacities from 500 to 22,000 lbs. per mount.
tional to minimize the number of different parts required to
Restraint/Vibration Isolator can be used as an independ-
Model
FMS
Seismically
Rated
do the job. The dual- purpose KSCA clip attaches the
ent restraint device or as a seismically rated vibration iso-
Both models are available with automatic leveling controls and custom
cable to the structure by anchoring to concrete with con-
lator assembly. Designed for the new building codes, the
mounting to meet your specific needs.
crete anchors or bolting or welding to steel. The two
unit is comprised of a restraint module and an optional
KSCA clips at the other end of the cable are used to
vibration isolation module. This modular design allows the
Typical applications include mechanical equipment and industrial
attach the cable to the hanger rod by clamping to the
engineer to design for seismic or wind forces independent
process equipment requiring low natural frequency isolation, as well
threaded rod directly above the clevis hanger. Kinetics
of the load and deflection requirements of the vibration iso-
as protecting sensitive equipment from disturbing floor-borne vibration.
offers additional labor-saving components to suspend
lator. The vibration isolation module uses Kinetics laterally
duct work, mechanical equipment, and electrical gear.
stable springs.
3
800.959.1229
accommodate spring, fiberglass, neoprene, or air
w w w. k i n e t i c s n o i s e . c o m
Kinetics Model RQ and RD Isolation Mounts are one-
Kinetics Model NP and NG Isolation Pads are single-
piece molded neoprene, color coded for identification,
ribbed or double-ribbed high quality elastomer, used
and have non-skid ribs on the bottom load surfaces.
singularly or in multiple layers, separated with steel
Each isolator incorporates two (2) bolt-down holes on
shims. Pads are 45 to 65 durometer and are designed
the bottom load surface and a tapped steel top load plate
for 60 to 120 PSI maximum loading. NP pads are avail-
for attachment to the supported equipment. Model RQ
able with rated deflections from 0.04" to 0.09". NG pads
isolators are designed for up to 0.15" static deflection;
are available with rated deflections from 0.13" to 0.19".
Model RD is available in four (4) sizes, and eleven (11)
Pads are available in 4”, 6”, 9” and 18" squares and may
Kinetics Model FH, RH, SH, SRH, and SFH Isolation Hangers are a family of products designed to
capacities from 55 to 4,000 lbs. The RQ is available in
be easily cut or drilled to meet field conditions. Kinetics
reduce the transmission of vibration and noise from suspended equipment and systems. FH and RH
two (2) sizes and four (4) capacities from 500 to 1,300 lbs.
Model NP and NG pads can be used to isolate noise,
hangers incorporate fiberglass or elastomer inserts only. SH hangers incorporate a spring insert only.
Kinetics Model RQ and RD are used to reduce the trans-
shock, and high frequency vibration generated by
SFH and SRH hangers are combination hangers, containing a fiberglass or elastomer pad insert in
mission of vibration from small pumps, vent sets, low
mechanical, industrial, or process equipment located on
series with a spring. Hanger inserts are designed for up to 50% overload capacity and for rod mis-
pressure packaged air-handling units, etc., and are
grade or in non-critical areas.
alignment over 30-degree arc. Brackets will carry 500% overload without failure. Hangers are available
selected when first cost must be minimized.
to 4” deflection and in capacities to 3,850 lbs. in standard designs. Hangers feature a Kinetics
patented No-Short spring cap which contains indexed steps to correspond to standard washer diameters for the appropriate rod diameter. The rod and washer stay centered in the No-Short cap.
FIBERGLASS ISOLATORS
KINFLEX FLEXIBLE CONNECTORS
THRUST RESTRAINTS
Kinetics Model KIP Vibration and Noise Isolation Pads
Kinetics Model AC Fiberglass Isolators, complete with
are
fiberglass
load plate and mounting brackets are designed for bolt-
Kinetics Model HSR Thrust Restraints are installed to
individually coated with a flexible elastomeric moisture
down applications such as vent fans, vane axial fans,
and contraction, isolate against the transfer of noise and
reduce movement associated with fan thrust and are
barrier. KIP fiberglass pads offer a constant natural
high-speed motors, and similar equipment. AC fiber-
vibration, and compensate for misalignment. KINFLEX con-
installed in pairs at the fan discharge. Model HSR uses
frequency over a wide load range. KIP pads are avail-
glass isolators are available in sizes with capacities
1” and 2" deflection springs in 35 to 3,500 lbs capacities.
able in capacities from 20 to 16,000 lbs. per pad, in
from 40 to 900 lbs. and deflections of 0.18" to 0.70".
KINFLEX Connectors prevent stresses due to expansion
nectors absorb movement created in piping systems by
pre-compressed,
inorganic,
inert
ambient temperatures, differences in temperature of materi-
thickness of 1”, 2”, 3”, and 4" and deflections from 0.18”
als handled, and differences in composition. The danger of
to 1.08". KIP pads are recommended for use in the
buckling or pulling apart and the resulting maintenance costs
reduction of vibration produced by pumps, chillers, cool-
are minimized.
ing towers, etc. They are also effective in reducing
shock transmission from punch presses and other
impact-producing machinery.
4
5
800.959.1229
NEOPRENE ISOLATORS
ISOLATION HANGERS
w w w. k i n e t i c s n o i s e . c o m
Kinetics Model RQ and RD Isolation Mounts are one-
Kinetics Model NP and NG Isolation Pads are single-
piece molded neoprene, color coded for identification,
ribbed or double-ribbed high quality elastomer, used
and have non-skid ribs on the bottom load surfaces.
singularly or in multiple layers, separated with steel
Each isolator incorporates two (2) bolt-down holes on
shims. Pads are 45 to 65 durometer and are designed
the bottom load surface and a tapped steel top load plate
for 60 to 120 PSI maximum loading. NP pads are avail-
for attachment to the supported equipment. Model RQ
able with rated deflections from 0.04" to 0.09". NG pads
isolators are designed for up to 0.15" static deflection;
are available with rated deflections from 0.13" to 0.19".
Model RD is available in four (4) sizes, and eleven (11)
Pads are available in 4”, 6”, 9” and 18" squares and may
Kinetics Model FH, RH, SH, SRH, and SFH Isolation Hangers are a family of products designed to
capacities from 55 to 4,000 lbs. The RQ is available in
be easily cut or drilled to meet field conditions. Kinetics
reduce the transmission of vibration and noise from suspended equipment and systems. FH and RH
two (2) sizes and four (4) capacities from 500 to 1,300 lbs.
Model NP and NG pads can be used to isolate noise,
hangers incorporate fiberglass or elastomer inserts only. SH hangers incorporate a spring insert only.
Kinetics Model RQ and RD are used to reduce the trans-
shock, and high frequency vibration generated by
SFH and SRH hangers are combination hangers, containing a fiberglass or elastomer pad insert in
mission of vibration from small pumps, vent sets, low
mechanical, industrial, or process equipment located on
series with a spring. Hanger inserts are designed for up to 50% overload capacity and for rod mis-
pressure packaged air-handling units, etc., and are
grade or in non-critical areas.
alignment over 30-degree arc. Brackets will carry 500% overload without failure. Hangers are available
selected when first cost must be minimized.
to 4” deflection and in capacities to 3,850 lbs. in standard designs. Hangers feature a Kinetics
patented No-Short spring cap which contains indexed steps to correspond to standard washer diameters for the appropriate rod diameter. The rod and washer stay centered in the No-Short cap.
FIBERGLASS ISOLATORS
KINFLEX FLEXIBLE CONNECTORS
THRUST RESTRAINTS
Kinetics Model KIP Vibration and Noise Isolation Pads
Kinetics Model AC Fiberglass Isolators, complete with
are
fiberglass
load plate and mounting brackets are designed for bolt-
Kinetics Model HSR Thrust Restraints are installed to
individually coated with a flexible elastomeric moisture
down applications such as vent fans, vane axial fans,
and contraction, isolate against the transfer of noise and
reduce movement associated with fan thrust and are
barrier. KIP fiberglass pads offer a constant natural
high-speed motors, and similar equipment. AC fiber-
vibration, and compensate for misalignment. KINFLEX con-
installed in pairs at the fan discharge. Model HSR uses
frequency over a wide load range. KIP pads are avail-
glass isolators are available in sizes with capacities
1” and 2" deflection springs in 35 to 3,500 lbs capacities.
able in capacities from 20 to 16,000 lbs. per pad, in
from 40 to 900 lbs. and deflections of 0.18" to 0.70".
KINFLEX Connectors prevent stresses due to expansion
nectors absorb movement created in piping systems by
pre-compressed,
inorganic,
inert
ambient temperatures, differences in temperature of materi-
thickness of 1”, 2”, 3”, and 4" and deflections from 0.18”
als handled, and differences in composition. The danger of
to 1.08". KIP pads are recommended for use in the
buckling or pulling apart and the resulting maintenance costs
reduction of vibration produced by pumps, chillers, cool-
are minimized.
ing towers, etc. They are also effective in reducing
shock transmission from punch presses and other
impact-producing machinery.
4
5
800.959.1229
NEOPRENE ISOLATORS
ISOLATION HANGERS
ISOLATION BASES
SESIMIC RESTRAINT ISOLATORS AND SNUBBERS
Kinetics Model CIB-H & L Inertia Base Frames are
pre-engineered welded steel pouring frames with
welded-in concrete reinforcement, equipment mounting
bolts, and vibration isolator brackets. The CIB bases are
designed to add mass to the rotating equipment in addition to rigidity and support for vibration isolation. CIB
bases are typically used with reciprocating compressors,
large chillers, compressors, fans, and pumps, and can
w w w. k i n e t i c s n o i s e . c o m
mount-type isolation.
Kinetics Model FLSS Seismic Control Restrained Spring
Kinetics Model FHS Seismic Control Restrained Spring
Vibration Isolators, in addition to the same features of our
Isolators meet specifications for Kinetics Model FDS iso-
Model FLS Restrained Spring Vibration Isolators, offer
lators and include a steel housing assembly to limit both
additional seismic restraint capabilities. The seismic
lateral and vertical movement of the supported equipment
capacity ratings for isolators are determined at Kinetics
during an earthquake without degrading the vibration iso-
Kinetics Model SFB Welded Structural Frame Bases are
by statically loading sample isolators in the vertical, both
lation of the spring during normal equipment operating
individually designed and fabricated to provide rigidity and
horizontal, and in the vertical and horizontal axis simulta-
conditions.
support to mechanical equipment.
neously until failure. The resulting maximum limits define
the restraint capacity envelope. Appropriate Model FLSS
and FHS Isolators are selected by first determining seismic force requirements computed at each isolator using
specific job specification data and local code requirements and then comparing those requirements to the
Kinetics Model SBB Structural Beam Bases are com-
capabilities as defined by the restraint capacity envelope.
posed up of two (2) structural members used to support
Standard FHS isolators incorporate a steel housing which
encloses a neoprene snubber. Depending on the load and
seismic zone, an optional steel spreader plate may be
applied to distribute the load among concrete anchors. A
neoprene pad fitted in series with the spring is provided.
Equipment attachment is by way of a bolt screwed downward through the equipment foot. Removal of the isolator
for servicing can be easily accomplished as the isolator is
equipment that does not require a unitary base, such as
not fitted with a protruding stud. In conformance with all
small close-coupled pumps, fans, and air handlers. The
current building code standards, the restraining system is
structural beams provide rigidity to the equipment and
designed to withstand a minimum 1.0 g acceleration force.
accommodate the installation of vibration isolation.
Motion is limited to approximately 0.2" in any direction.
AIR MOUNTS
Kinetics Seismic Cable Restraints are designed to pro-
6
Kinetics Model KAM and CAM Air Isolators are pneumatic, elas-
vide seismic restraint capacity in excess of the new build-
tomeric vibration mounts. The CAM is available in four (4) sizes sup-
ing codes and reduce costly field installation time. The
porting loads up to 7,500 lbs. The KAM is available in seven (7) sizes
engineered brackets and cable assemblies are multi func-
Kinetics
with capacities from 500 to 22,000 lbs. per mount.
tional to minimize the number of different parts required to
Restraint/Vibration Isolator can be used as an independ-
Model
FMS
Seismically
Rated
do the job. The dual- purpose KSCA clip attaches the
ent restraint device or as a seismically rated vibration iso-
Both models are available with automatic leveling controls and custom
cable to the structure by anchoring to concrete with con-
lator assembly. Designed for the new building codes, the
mounting to meet your specific needs.
crete anchors or bolting or welding to steel. The two
unit is comprised of a restraint module and an optional
KSCA clips at the other end of the cable are used to
vibration isolation module. This modular design allows the
Typical applications include mechanical equipment and industrial
attach the cable to the hanger rod by clamping to the
engineer to design for seismic or wind forces independent
process equipment requiring low natural frequency isolation, as well
threaded rod directly above the clevis hanger. Kinetics
of the load and deflection requirements of the vibration iso-
as protecting sensitive equipment from disturbing floor-borne vibration.
offers additional labor-saving components to suspend
lator. The vibration isolation module uses Kinetics laterally
duct work, mechanical equipment, and electrical gear.
stable springs.
3
800.959.1229
accommodate spring, fiberglass, neoprene, or air
FREE-STANDING SPRING ISOLATORS
RESTRAINED SPRING ISOLATORS
ROOFTOP ISOLATION CURBS
Kinetics Model FDS Spring
Isolators
unhoused,
are
free-standing,
large
diameter
laterally stable steel springs
Kinetics Model KSR Roof Rails are pre-engineered,
contained in an upper load
spring-supported isolation systems designed for curb-
plate/leveling assembly and
supported rooftop equipment. The KSR rails are easy-
lower load plate/noise pad
to-install vibration isolation systems that provide an
assembly, for control of high fre-
airtight and watertight seal between the rooftop
quency vibration. They are also
mechanical equipment and the roof curb. KSR rails are
available as an all-welded unit
available in 1" and 2" deflection.
spring isolators are designed for
spring deflection ranges from 0.71" to 4.00” with load
capacity up to 23,200 lbs. FDS spring isolators are
recommended for the isolation of floor-mounted refrigeration compressors, pumps, packaged air handlers, airconditioning equipment, centrifugal and axial fans, and
internal combustion engines. For equipment subject to
weight change or high wind loads, see Restrained
Spring Isolators.
HOUSED SPRING ISOLATORS
Kinetics Model FLS Restrained Spring Isolators are large
diameter, laterally stable steel springs assembled into a
welded steel housing designed to limit vertical movement of
the isolated equipment if equipment weights are reduced or
Kinetics Model KSCR
if the equipment is subjected to large external forces. The
Affordable...easy-to-install...all-in-one roof curb AND
spring elements are complete with high frequency vibration
vibration isolation for under 20-ton packaged rooftop
control noise pads and an adjustable top load plate with lev-
units! Standard features include:
eling bolts. They are available with deflections 0.71" to 4.00"
• Internal seismic restraint
for loads up to 23,200 lbs. The FLS isolators are recom-
• 100 mph wind restraint
mended for the isolation and restraint of large fluid-carrying
• 1" or 2" deflection springs
equipment such as boilers, chillers, and cooling towers, or
• Supply and return flexible connector support hardware
for equipment subjected to high wind loads.
• EPDM airtight and weather-tight seal for non-ducted
800.959.1229
w w w. k i n e t i c s n o i s e . c o m
for bolt-down applications. FDS
applications
• High profile, non-interference aluminum equipment rail
• Accessible, interchangeable springs
Kinetics Model SL and SM Spring Isolators are high
Kinetics Model ESR
deflection stable springs assembled into telescoping
Heavy-duty, complete vibration isolation curb for the
aluminum or cast iron housings,
BIG rooftop unit jobs!
complete with 1/4"
noise pads bonded to the lower load surface. Adjusting
Standard Features include:
and leveling bolts are part of the top housings. Model
• 1 g seismic restraint & 125 mph wind restraint
SM spring isolators are designed with an adjustable
snubbing feature to reduce movement during start-up
Kinetics Model FRS Spring Isolators are light capacity,
and shutdown. Model SM isolators are available with
vertically restrained isolators with rated deflections from
deflections to 1.84" in capacities from 250 to 3,000 lbs.
0.71" to 2.00" in capacities up to 3,500 lbs. FRS isolators are
Model SL isolators are available with the same deflec-
recommended for the isolation and restraint of lightweight
tion ranges and capacities from 35 to 3,500 lbs. Kinetics
mechanical equipment subject to high wind loads or equip-
Model SL and SM spring isolators are typically used to
ment subject to weight change. FRS isolators can also be
isolate mechanical equipment subject to freguent start-
used for support of vertical pipe risers where isolation is
up and shutdown such as compressors and engine
required yet vertical motion controlled. The FRS can be used
generators.
in outdoor applications.
2
• Access ports for each isolator to inspect, level, or
change springs after equipment placement
• Up to 4" deflection, powder-coated steel springs with
50% overload capacity
• High-frequency noise isolation pads
• Environmentally inert elastomeric seal for an air- and
watertight closure between the curb and isolation rail
• Supply and return duct support hardware
• Structural steel curb with wood nailer.
7
w w w. k i n e t i c s n o i s e . c o m
ABOUT KINETICS NOISE CONTROL
Kinetics Noise Control has been engineering and manufacturing vibration
isolation and noise control products and systems for over 40 years. We
pioneered the use of pre-compressed molded fiberglass for vibration isolation.
Throughout the years, we have developed and refined a complete line of noise
and vibration control products. In addition to the vibration isolation products
illustrated in the brochure, we also offer complete designed pipe riser isolation
systems, computer-assisted seismic design, engineered floating floor systems
for control of airborne and impact noise, and a complete selection of barriers,
absorbers and damping materials. Kinetics offers the engineering expertise,
laboratory, and field testing capabilities to work with you and your acoustical
consultant to develop a solution to your specific noise control problem.
United States
6300 Irelan Pl
P.O. Box 655
Dublin, Ohio 43017
800.959.1229
ph. 614.889.0480
fx. 614.889.0540
Canada
1720 Meyerside Drive
Mississauga, Ontario
L5T 1A3
ph. 905.670.4922
fx. 905.670.1698
www.kineticsnoise.com
sales@kineticsnoise.com
Vibration Products 3/04