Low Cost, Non-isolated Type POL DC-DC Converter RoHS Minimal derating in this size ! 10A/16A/25A BST-L (SIP) Series Compliance Low Cost, DOSA Compatible, POL DC-DC Converter Input: +2.4V to +5.5V Output: +0.7525V (+0.7525V to +3.63V) Input: +6.0V to +14.0V Output: +0.7525V (+0.7525V to +5.5V) - Remote ON/OFF Control Voltage can be set with external resistors (ex. 1V, 1.2V, 1.5V, 1.8V, 2.5V, 3.3V, 5V) Models - Negative and Positive Input V Output V Output I Line Reg. Load Reg. Ripple Noise Efficiency BST-L (SIP) Series ON/OFF logic Vdc Vdc A %(typ.) %(typ.) mVpp(typ.) %(typ.) 0.7525 BST04L-0.7S10xDS 2.4 to 5.5 - Industry Standard Package 0 to 10 25 95.5 0.6 1.0 DOSA Compatible (0.7525 to BST04L-0.7S16xDS 0 to 16 20 95.5 3.0 to 5.5 - High Efficiency 3.63) BST04L-0.7S25xDS 0 to 25 20 94.0 - Adjustable Output Voltage BST12L-0.7S10xDS 0 to 10 25 95.2 0.7525 0.2 0.8 - Over Current Protection BST12L-0.7S16xDS 6.0 to 14.0 0 to 16 40 94.0 (0.7525 to 5.5) - Under Voltage Lock Out BST12L-0.7S25xDS 0 to 25 25 95.0 *Note 4: Ripple noise and efficiency values are when -Operating Temp -40°C to +85°C *Note 1: Specify the type of the ON/OFF logic as below for X column to complete the model type when placing orders. *Note 4: they are under the following conditions. (Temp Derating Required.) e.g. Positive type:BST04L-0.7S10PDS BST04L : Input voltage 5V, output voltage 3.3V, the rated load. - Non-Isolated Converter Negative type:BST04L-0.7S10NDS BST12L : Input voltage 12V, output voltage 5V, the rated load. - RoHS Compliance *Note 2: Output voltage inside the ( ) indicates the *Note 5: Ripple noise is measured by 20MHz bandwidth, - Halogen free *Note 5: with the following ceramic capacitors. *Note 2: adjustable range. - Output voltage set *Note 3: Input/output voltage requires voltage difference. BST04L-10A, BST12L-25A : 47µF×4 at input - accuracy ±1.5% BST04L-10A, BST12L-25A : 47µF×2+1µF at output BST04L : Vout≦1.8V, Vin=2.4 to 5.5V TRIM pin open BST04L-16A/25A, BST12L-16A : 47µF×4 at input BST04L : 1.8V<Vout≦2.5V, Vin=3.3 to 5.5V Vo=0.7525V, BST04L-16A/25A, BST12L-16A : 47µF×4+1µF at output BST04L : Vout>2.5V, Vin=4.5 to 5.5V Io=0A, Ta=25℃ BST12L-10A : 47µF×2 at input BST12L : Vout≦3.8V, Vin=6 to 14V BST12L-10A : 47µF×2+1µF at output BST12L : Vout>3.8V, Vin=8 to 14V *Note 6: Depending on the ambient temp condition, <Derating Curve> <Outline> 50.80±0.5 2 1 2 3 4 5 6 7 8 910 DOSA Compatible (1.0m/s) BST12L-0.7S10PDS 0.64 P2.54x3=7.62 P2.54 P2.54x4=10.16 1.27 7.62 max. 35.56 Weight : 8.0g typ. Units : mm (Side View) <Standard Connection Diagram> ON/OFF logic type:Positive Vin Vout ON/OFF logic type:Negative 1, 2, 4 SENSE 7, 8 +Vin C1 TRIM 10 ON/OFF GND SW Vout SENSE SW 9 C2 C3 Load +Vin C1 RTrim BST-L(SIP) Series TRIM 10 ON/OFF GND 1, 2, 4 3 9 C2 C3 Load RTrim 5, 6 5, 6 RTrim:Vout setting resistor RTrim:Vout setting resistor BST04L-10A, BST12L-25A C1 : 47μF×4 (Ceramic Capacitor) C2 : 1μF (Ceramic Capacitor) C3 : 47μF×2 (Ceramic Capacitor) Vin 3 BST-L(SIP) Series 30 40 50 60 70 80 90 Ambient Temp [℃] BST12L-0.7S16PDS (Vin=12V, Vo=5.0V) Function Vout Vout SENSE Vout GND GND Vin Vin TRIM ON/OFF 45.72 7, 8 DOSA Compatible (1.0m/s) BST12L-0.7S16PDS Pin 1 2 3 4 5 6 7 8 9 10 13.6±0.5 4 30 40 50 60 70 80 90 Ambient Temp [℃] BST12L-0.7S10PDS (Vin=12V, Vo=5.0V) Output Current [A] 6.2max. 6 0 16 14 12 10 8 6 4 2 0 8.7max. 8 3.2±0.5 Output Current [A] 10 *Note 6: cooling air flow may be required. BST04L-16A/25A, BST12L-16A C1 : 47μF×4 (Ceramic Capacitor) C2 : 1μF (Ceramic Capacitor) C3 : 47μF×4 (Ceramic Capacitor) BST12L-10A C1 : 47μF×2 (Ceramic Capacitor) C2 : 1μF (Ceramic Capacitor) C3 : 47μF×2 (Ceramic Capacitor) - SW : When short, the output is off. - Trim: When open, the output voltage is 0.7525V. - When adjusting the output voltage, connect RTrim between Trim pin and GND. - Note! This catalogue is an outline of the products. When designing, be sure to refer to the data sheets. DC-DC CONVERTERS BDD2010.07A