LV-014 INSTALLATION INSTRUCTIONS
SAFETY INSTRUCTIONS
BEFORE STARTING THE INSTALLATION OF THE NEW FIXTURE:
1) READ INSTRUCTIONS THOROUGHLY
2) DISCONNECT POWER TO FIXTURE
1. Read all instructions carefully before modifying luminaire.
2. This fixture must be wired in accordance with the national
electrical code and applicable local codes and ordinances.
3. Proper grounding is required to insure personal safety.
4. All work should be done by a qualified electrician.
PRIOR TO INSTALLATION:
1) REMOVE GLASS LENS FRAME & SET ASIDE. (FIG. 2)
2) REMOVE LED REFLECTOR ASSEMBLY & SET ASIDE. (FIG. 2)
4) REMOVE TWO HEX NUTS TO SEPERATE
BACK PLATE FROM FIXTURE HOUSING. (FIG. 2)
INST0183
PAGE: 1 OF 1
WARNING:
- RISK OF ELECTRIC SHOCK Disconnect power before starting
installation or servicing luminaire.
MOUNTING OPTION # 2
MOUNTING HARDWARE
(SUPPLIED BY ECLIPSE LIGHTING)
(4) GASKETS, (4) BRACKETS &
(4) CAPCON ANCHOR SCREWS
A1
MOUNTING OPTION # 1
"J" BOX MOUNTING STRAP
WALL MOUNT
BACK PLATE
MOUNTING OPTION 1:
TWO POINT STRAP MOUNT
1) MOUNT STRAP TO "J" BOX.
2) WIRE "FEMALE" END OF SUPPLIED 3-POLE
DISCONNECT TO LINE SIDE FEED.
3) LOCATE AND DRILL OUT TWO DRILL POINTS
IN THE SURFACE BACK BOX, (ABOVE BALLAST).
4) CONNECT MALE TO FEMALE LINE SIDE
DISCONNECT TOGETHER AND SECURE BACK
BOX TO MOUNTING STRAP USING CONTRACTOR
SUPPLIED HARDWARE.
5)
FIXTURE HOUSING
LINE SIDE
"FEMALE"
DISCONNECT
BACK PLATE
LATCH TABS
GO TO HOUSING MOUNTING STEP 1
FIG.1
BACK PLATE
HEX NUTS
MOUNTING OPTION 2:
FOUR POINT MOUNTING
(SUGGESTED FOR WET LOCATION)
LED REFLECTOR
ASSEMBLY
SECURED WITH
TWO HEX NUTS
1) POSITION PLATE ON MOUNTING SURFACE, MARK
AND PRE-DRILL (4) HOLES.
2) USE MANUFACTURER SUPPLIED GASKETS, BRACKETS AND
BLUE TAPCON SCREWS TO MOUNT BACK PLATE TO WALL.
(IF MOUNTING OVER A RECESSED JUNCTION BOX, ENSURE
PAD GASKET COVERS AND SEALS THE "J" BOX.)
IF USING SURFACE MOUNTED CONDUIT, CONTRACTOR IS
RESPONSIBLE FOR SUPPLYING AND USING APPROPRIATE
WATER TIGHT FITTINGS.
CONTRACTOR IS RESPONSIBLE FOR SUPPLYING
AND APPLYING ADDITIONAL SEALANTS
(SUCH AS CAULK OR SILICONE) TO ENSURE
WATER TIGHT SEAL.
3)
GO TO HOUSING MOUNTING STEP 1
HOUSING MOUNTING
DETAIL "A1"
1) ALIGN AND LATCH FIXTURE HOUSING ONTO
THE BACK PLATE LATCH TABS. APPLY FIRM PRESSURE
DOWNWARD TILL HOUSING RESTS OVER THE TWO
THREADED STUDS AT THE BOTTOM OF THE BACK PLATE.
SECURE FIXTURE HOUSING WITH (2) ORIGINAL 8-32
HEX NUTS SUPLPIED WITH FIXTURE.
2) RECONNECT THE TWO WIRE DISCONNECT AND REINSTALL
THE LED REFELCTOR ASSEMBLY.
3) REPLACE THE GLASS LENS FRAME WITH THE ORIGINAL
MANUFACTURER SUPPLIED SECURITY SCREWS.
GLASS LENS FRAME
ATTACHES WITH
FOUR TORX
SECURITY SCREWS
FIG.2
We reserve the right to revise the design or components of any product due to parts availability or change in UL standards, without assuming any obligation or liability to modify
any products previously manufactured and without notice. This literature depicts a product DESIGN that is the SOLE and EXCLUSIVE PROPERTY of ECLIPSE LIGHTING, INC.
--An Illinois Corporation. In compliance with U.S. COPYRIGHT and PATENT requirements, notification is hereby presented in this form that this literature, or the product it depicts,
is NOT to be copied, altered or used in any manner without the express written consent of, or contrary to the best interests of, ECLIPSE LIGHTING, INC.---05/04/1994
© 2010 Eclipse Lighting, Inc.
All Rights Reserved Designs
Protected by Copyright
REV. 7/12/10