LED-Airport Lighting LED Taxiway Edge Light 795 – Low Intensity APPLICATION FEATURES The low-intensity fitting type 795 is intended to be used in all weather conditions, designed for operation under CAT I, II and III conditions. It is also suitable as stopbar and obstruction light. ➔➔ The design is based on FAA Advisory circular AC 150 / 5345-46A ➔➔ Heat resistant, one lens system ➔➔ The lens surface is smooth and easy to clean ➔➔ Can be supplied with prefocused 10 W / 6,6 A LED with an average lifetime of 50.000 hours at 100 % intensity ➔➔ Aviation colour lenses available ➔➔ Fully corrosion proof components ➔➔ Finished in stove enamel aviation yellow ➔➔ Suitable for use with a daylight marker cone DESCRIPTION The fitting type 795 is a fixed-focus, low-intensity, omnidirectional, lightweight, elevated taxiway edge light constructed to meet the ­demands for easy mounting, levelling and service, capability to resist jet blast from today’s aircrafts, and last but not least to give sufficient light intensity, in the right angles with the use of a standard halogen lamp or low power LED with belonging electronics. HELLA KGaA Hueck & Co. Airport Lighting Rixbecker Straße 75 | 59552 Lippstadt /Germany | Tel. + 49 2941 38 - 1175 | airportlighting@hella.com | www.hella.com /airportlighting Mounting devices Ø50 +0/-0,2 Ø34,6 +/-0,1 ø 35 2 5 15 Ø55,5 28.5 2"RG (Ø60) Type A Type No. Code 0.3 62.0 +- 0.0 Type C Technical Drawing Total Type No: 795.LED-LI-b.0.A - LI: Low Intensity 10W LED - MIRE: Medium Intensity 20W LED Application - b: blue (available for LI and MIRE) - r: red (for LI) - g: green (for LI) - cl: clear (for LI) - c/c: clear/clear (for MIRE) - c/y: clear/yellow (for MIRE) - r/g: red/green (for MIRE) Secondary Lead - 0: No secondary lead, except for standard lamp terminals AMP 6.3 x 0.8 mm - 4: With 0.4 m lead with 2-pole FAA plug Mounting Device - A: Breakable coupling A - C: Breakable coupling C Light Distributions cd 350 300 250 200 150 Light transmission White ≈ 1,000 Blue ≈ 0,025 Red ≈ 0,220 Yellow ≈ 0,450 100 50 +2 4 6 8 10 12 14 16 18° vertical Development as of May 2014. Subject to technical modifications. All rights reserved by HELLA KGaA Hueck & Co. - 795.LED 0 30 Fig. 1 7 20 25 HELLA Induperm breakable coupling is ­calculated and tested to break at: 64 Kgm ± 4 Kgm which is in according FAA AC 150 / 5345-46B, sect 3.4.2.1. -2 0.1 3.0 -+ 0.0 3 67 Ø28,5 Ø45 Basis Type ± 0.1 13 45° 33 +0/-0,2 ➔➔ Type A: With 2˝ thread (European standard thread or 11,5 NPT or NPS) ➔➔ Type C: For 2˝ pole mounting ➔➔ Customer designed couplings 37.05 ± 0.05 33,2 +0,2/-0 13 HELLA Induperm elevated light fixtures can be ­delivered with various types of breakable ­couplings: 2 x M6 Ø36,4 +/- 0,1