QCF
Product Information
Surface Mount Gas Canopy
Installation Instructions
Project Name
Type
Catalog Number
Date
WARNINGS & SAFETY INFORMATION-PLEASE READ CAREFULLY!
•
•
•
•
•
•
Risk of fire and/or electric shock. This product is to
be installed by a qualified electrician only. Installation
requires knowledge of fluorescent lighting luminaire
electrical systems. Do not attempt if unqualified.
Do not expose wiring to sheet metal edges or
other sharp objects to prevent damage.
Fixture is suitable for damp locations.
Install in accordance with all national and local electrical
codes. Manufacturer assumes no responsibility for the
improper installation or application of this fixture.
Contact the manufacturer for any questions or
concerns regarding installation of this fixture.
Warning: This product is sensitive to Electrical Static
Discharge (ESD). Care should be taken to avoid direct
contact with the LEDs. Installers should be grounded
using a wrist strap or other suitable method of
grounding. Failure to ground the installer may cause
pre-mature failures and void the fixture warranty.
TOOLS REQUIRED
1.
2.
3.
4.
5.
6.
7.
8.
Electric drill/driver, of sufficient power/speed to cut
conduit-passage holes through the canopy.
Twist drill, 7/16”, suitable for drilling
through the material of the canopy.
Hole saw(s), of correct size/material for cutting
conduit-passage holes through the canopy.
Slotted screwdriver
Wrenches suitable for the attachment of
conduit / junction box components
Center punch
Metal deburring tool, suitable for deburring
the drilled/punched holes
Sealant gun, for application of silicone sealant (if needed)
INCLUDED MATERIALS
A. (1) Gas Canopy Lamp / Mounting Assembly
B. (2) Large Junction Box
NEEDED MATERIALS
A. (4) Fasteners, suitable for the attachment of
the included junction box to the gas canopy
B. Conduit fittings, as needed for water-proof
penetration of existing conduit through the gas canopy
C. Wire connectors of suitable size
D. Silicone sealant, squeeze-tube or cylindrical tube
E. Isopropanol
F. Clean rags
INSTALLATION INSTRUCTIONS
1. Per the hole layout diagram below, drill
installation holes into the gas canopy:
2. Install the supplied Junction Box onto the gas
canopy. The Junction Box can be mounted with either
screws or bolts, either 1/4” or 3/8” size. All canopy
penetrations must later be sealed, in order to prevent
rainwater from penetrating into the junction box.
Page 1/4 - Revised 08/06/14
© 2014 Precision-Paragon [P2], a division of Hubbell Lighting, Inc. Because of continuing product improvement programs, Precision-Paragon [P2] reserves the right to change
specifications without notice. Tel [West Coast] 714.386.5550 [Midwest] 715.381.2971 [East Coast] 352.692.5900 / Website www.P-2.com
QCF
Surface Mount Gas Canopy
Installation Instructions
INSTALLATION INSTRUCTIONS
3. (View of the installed Junction Box)
4. Prepare to install the Gas Canopy Lamp/Mounting
Assembly into the Junction Box
5. The Gas Canopy Lamp Assembly must be oriented
as shown, relative to the indicated seams in the
Junction Box
6. The Gas Canopy Lamp Assembly should NOT be
oriented this way, relative to the indicated seams in
the Junction Box.
Like THIS
7. Rotate the Lamp Assembly into the Junction Box,
such that the Lamp Assembly’s notches engage the
Junction Box’s flanges (see sequence below):
NOT Like this
8. Rotate the Lamp Assembly, such that its
notches engage the Junction Box’s flanges:
Lamp Assembly's notches engaging
the Junction Box's flanges
Page 2/4 - Revised 08/06/14
© 2014 Precision-Paragon [P2], a division of Hubbell Lighting, Inc. Because of continuing product improvement programs, Precision-Paragon reserves the right to change specifications
without notice. Tel [West Coast] 714.386.5550 [Midwest] 715.381.2971 [East Coast] 352.692.5900 / Website www.P-2.com
QCF
Surface Mount Gas Canopy
Installation Instructions
INSTALLATION INSTRUCTIONS
9. Make the wire connections to the Lamp Assembly.
10. Lift the Lamp Assembly into the Junction Box.
11. Loosen the indicated hex-head screw, and slide the
screw away fro the edge of the Lamp-Mounting Plate
Loosen this screw 5 turns...
...and slide it away from the edge of
the Lamp-Mounting Plate.
Page 3/4 - Revised 08/06/14
© 2014 Precision-Paragon [P2], a division of Hubbell Lighting, Inc. Because of continuing product improvement programs, Precision-Paragon reserves the right to change specifications
without notice. Tel [West Coast] 714.386.5550 [Midwest] 715.381.2971 [East Coast] 352.692.5900 / Website www.P-2.com
QCF
Surface Mount Gas Canopy
Installation Instructions
INSTALLATION INSTRUCTIONS
12. In order to fully engage and secure the
Lamp Assembly, follow this sequence:
10. Lift the Lamp Assembly into the Junction Box.
Slide this screw over as far
as possible, as shown:
13. While pushing the Lamp-Mounting Plate upward, slide the screw in the direction shown, such that
the Latch Clip slides over the Junction Box’s flange. (Note: The Lamp-Mounting Plate is shown transparent
in these views, in order to clarify the latching of the Assembly).
Slide the screw as far as possible in the direction shown.
The Latch Clip will slide along with it.
The Latch Clip should slide on top of the Junction Box’s
flange, as shown. Tighten the screw.
14. On the top side of the canopy, seal all fastener and
wiring penetrations. First clean with alcohol, then
seal with silicone sealant.
15. Installation Complete.
Page 4/4 - Revised 08/06/14
© 2014 Precision-Paragon [P2], a division of Hubbell Lighting, Inc. Because of continuing product improvement programs, Precision-Paragon reserves the right to change specifications
without notice. Tel [West Coast] 714.386.5550 [Midwest] 715.381.2971 [East Coast] 352.692.5900 / Website www.P-2.com