Overview
Lighting Control Overview
RTC
• Inbuilt real time clock
• Automatic daylight savings adjustment
• Atomic clock synchronisation (NTS).
Triggers
Inputs
Schedules
Network
Conigurable inputs with dynamic modes and
multistaged override timers for:
• Automatic time based events
• Touch screen
• Sunrise and sunset with offset
• Computer with building monitor
• Push buttons and switches
• Repeat timers
• Linked controllers
• Daylight sensors
• Linked timers with offset
• PDAs/smartphones
• Occupancy sensors
• Holidays and holiday schedules.
• SMS (text messages).
Direct Arc Level
DALI Commands
Extended Commands
• Direct ARC power control
• Dimming commands: Min, Max, etc.
• Conditional commands: Min_If_On, etc
• Logarithmic dimming curve with an arc power level
of 0.1% to 100%.
• Scenes with individual light levels
• Controller commands
• Status reporting
• Timed sequences.
• RF receivers, etc.
Actions
• Coniguration.
Control
Targets
CLIPCOM 21240 May 2010 3001
Ballasts
Groups
Broadcast
Outputs
Up to 64 ballasts (1 loop) or up to 128
ballasts (2 loops).
Up to 16 DALI Groups per loop
+ 48 extended Groups per loop.
Single loop or all loops.
8 onboard outputs to drive relays.
© Copyright Clipsal Australia Pty Ltd. The identified trademarks and copyrights are the property of Clipsal Australia Pty Ltd unless otherwise noted.
www.dalicontrol.com
Schematic
Simple DALI Room Control Schematic
64 Addresses (max.) per DALI Loop (max. 300m)
DALI-01
DALI Power Supply
250mA max.
DALI Light Fittings
00
01
02
03
04
05
06
07
Optional Ethernet Controller/Gateway
with RTC and I/O
DALI Wallplate
DALI Light Sensor
DALI Occupancy Sensor
DALI Wallplate
Notes:
• DALI is an international standard lighting control system. The
schematic diagram shows a DALI network (DALI-01) powered
by a DALI power supply.
• DALI ECGs are available for FL and CFL lamps, discharge
lamps, low voltage halogen lamps, incandescent lamps, LEDs,
emergency lights, etc.
• The eight light fittings (addressed from 00 to 07) can be any light
fitting from any manufacturer fitted with DALI ECG (electronic
control gear).
• The light fittings are controlled by DALI ECDs (electronic control
devices) such as DALI wallplates and DALI sensors from any
manufacturer, including DALI control’s DC100 Series of DALI
control devices.
CLIPCOM 21240 May 2010 1011
• DALI can also control legacy light fittings including fixed output,
analogue 1 to 10V and DSI dimmable fittings.
© Copyright Clipsal Australia Pty Ltd. The identified trademarks and copyrights are the property of Clipsal Australia Pty Ltd unless otherwise noted.
www.dalicontrol.com
Schematic
Floor Control Schematic
64 Addresses (max.) per DALI Loop (max. 300m)
DALI
Power
Supply
250mA
max.
DALI-01
EXIT
DCDALxx-xx
DCDALCI
00
01
02
03
04
05
DALI EMG
(06)
63
DCBM DALI
Line Controller
Occupancy and/or
Light Sensor
Ethernet
Wallplate and Sensors
Wallplate
To Riser or Hub for Optional
Computer Monitoring and Control
To Security or Access Control Panel
DCDALCI
DALI
Power
Supply
250mA
max.
DALI-02
EXIT
00
DALI EMG
(60)
01
02
03
04
63
DALI EMG
(61)
DALI Sensor
DALI Wallplate
Notes:
• The controller manages up to two DALI networks. The controller
includes scheduling, digital inputs, digital outputs and an RJ45
Ethernet network socket for computer monitoring and control.
CLIPCOM 21240 May 2010 1012
• Inputs on the controller can be used for wallplates, sensors and
interfacing to security and access control panels, etc.
• The controller manages a DALI group based on inputs from
standard switches and sensors.
• Each DALI network requires a DALI power supply and a DALI
interface.
© Copyright Clipsal Australia Pty Ltd. The identified trademarks and copyrights are the property of Clipsal Australia Pty Ltd unless otherwise noted.
www.dalicontrol.com
Schematic
Building Control Schematic
Riser to Higher Floors
64 Addresses (max.) per DALI Loop, 00 to 63
64 Addresses (max.) per DALI Loop, 00 to 63
DALI-11
DALI-13
EXIT 03
00
01
02
EXIT 03
00
63
01
Wallplate and Sensors
02
63
Wallplate and Sensors
To Master Override Switch
Switchboard
To Security/Access Control Panel
DALI-14
DALI-12
EXIT 03
EXIT 03
00
01
02
00
63
01
02
DCDALxx-xx
63
DALI EMG
(61)
DALI Sensor
DALI Wallplate
Ethernet
DALI Area Controller with
Wallplate and Sensors
Riser to Lower Floors
Notes:
• The controller manages up to two DALI networks and includes
scheduling, digital inputs, digital outputs and an RJ45 Ethernet
socket for computer monitoring and control.
CLIPCOM 21240 May 2010 1013
• The switchboard contains controller/gateways, DALI power
supplies and DALI interfaces.
© Copyright Clipsal Australia Pty Ltd. The identified trademarks and copyrights are the property of Clipsal Australia Pty Ltd unless otherwise noted.
www.dalicontrol.com
Schematic
Typical Switchboard Schematic
Switchboard
Riser to
Control Room
DALI Networks
DALI-01
DCDALPSxxx
EXIT
DCDALCI
DCDALCI
00
01
02
63
Wallplate
DALI-02
DCDALPSxxx
EXIT
00
01
02
63
Ethernet Switch
Wallplate
DALI-03
DCDALPSxxx
EXIT
DCDALCI
DCDALCI
00
01
02
63
Wallplate
DALI-04
DCDALPSxxx
EXIT
00
01
02
63
Wallplate
Notes:
DALI-05
DCDALPSxxx
• The controller manages up to two DALI
networks. Each controller includes
scheduling, inputs, outputs and an RJ45
Ethernet socket for computer monitoring
and control.
EXIT
DCDALCI
DCDALCI
00
01
02
63
Wallplate
DALI-06
DCDALPSxxx
EXIT
00
Wallplate
CLIPCOM 21240 May 2010 1015
01
02
63
• Each DALI network requires a power
supply and an interface.
• Power supplies for the controller and
Ethernet switch are not shown in the
schematic diagram. Refer to wiring
diagrams for full details.
© Copyright Clipsal Australia Pty Ltd. The identified trademarks and copyrights are the property of Clipsal Australia Pty Ltd unless otherwise noted.
www.dalicontrol.com
Wiring
BM-DALI Controller Wiring Overview
To CCT Breaker
Starter Socket
Socket or T-Piece
LL
N
N
DA
DALI-A
DA
DALI ECG
(Addr 0)
DCDAL10-0402
DCDAL0-02
DALI EMG
(Addr 4)
+V
DALI Controllers Including:
DALI Wallplates, Occupancy
Sensors, Light Sensors, Group
Controllers, Scene Controllers
Touch Screens, etc.
To DALI-B
DCDALCI
DC IN
GND
Notes:
DCDALCI
BMxxxx-DALI
LINE
CONTROLLER
INPUTS 0..15
-V
DALI ECG
(Addr 63)
DALI EMG
(Addr 2)
DCDALP250
or
DCDALP200
DCDALP250
or
DCDALP200
DALI ECG
(Addr 3)
EXIT
SWITCHBOARD
DCPxx/xx
DALI ECG
(Addr 1)
• The diagram depicts a typical wiring layout for a DALI line.
To Switches and Push Buttons,
Occupancy and Light Sensors,
Security and Access Control
Panels, etc.
• The DCPxx/xx power supply provides d.c. power for BM-DALI line controllers and for
sensors connected to BM-DALI inputs.
• The DCDALP200 or DCDALP250 are current limited, DIN rail mount DALI power supplies.
• One DCDALP200 or DCDALP250 is required per DALI line.
DC IN
-
• The DCDALCI is the DALI communications interface for the BM-DALI line controller.
CAT5e or CAT6
+
BUILDING
MONITOR
Ethernet
Switch
• One DCDALCI is required per DALI line.
• Each DALI line can support up to 64 DALI ECG’s addressed from 0 to 63.
• DALI ECGs are available for FL and CFL lamps, LV halogen, HID, LEDs, emergency
fittings, fixed output, DSI and 1 to 10V analogue fittings, etc.
• The computer and other Ethernet equipment is optional and can be used to monitor and
control the system.
DCLCD35 Control Panel
or DCLCD70 Touch Panel
CLIPCOM 21240 May 2010 2001
Ethernet Network to Computers, Touch Screens, LCD
Control Panels and BM-DALI Network Controllers
• DALI lines must be wired to the DALI standard and to local regulations.
© Copyright Clipsal Australia Pty Ltd. The identified trademarks and copyrights are the property of Clipsal Australia Pty Ltd unless otherwise noted.
www.dalicontrol.com
Wiring
BM-DALI Controller Digital Outputs
+
2
1
2
1
4
3
4
3
6
5
6
5
7
8
7
8
12V DC Power Supply
DCBM DALI Line Controller
Plug Relay and Base
(typical H72 x W28 x D67mm each base)
Notes:
Output Circuit
• The DCBM DALI line controller has eight internal digital outputs;
OUT 0 to OUT 7. Each output can sink 200mA.
+K
Load
OUT/AUX
+
-
External
Power
Suppy
• When using the digital outputs to switch inductive loads it may
be necessary to power K with a separate power supply.
• Relay base terminals (arrangement shown is for PTF08A):
1.
Contact 1 Normally Closed
2. Contact 1 Normally Open
3. Contact 1 Common
4. Contact 2 Normally Closed
5. Contact 2 Normally Open
GND
Internal Circuit
External Components
6. Contact 2 Common
7.
Coil
8. Coil
CLIPCOM 21240 May 2010 2003
© Copyright Clipsal Australia Pty Ltd. The identified trademarks and copyrights are the property of Clipsal Australia Pty Ltd unless otherwise noted.
www.dalicontrol.com
Wiring
DCBM-DALI Line Controller Ethernet Overview
Administration Computer (optional)
Ethernet Switch
Level xyz Distribution Board
Ethernet Switch
BUILDING
MONITOR
DCBM-DALI Line Controller
CAT5e Cable
DCDALCI
DALI-01
DCDALCI
DALI-02
DCDALCI
DALI-03
DCDALCI
DALI-04
DCDALCI
DALI-05
DCDALCI
DALI-06
DCBM-DALI Line Controller
DCBM-DALI Line Controller
Ethernet Cabling
to Other Levels
DCLCD35 Control Panel
or DCLCD70 Touch Panel
Notes:
• Ethernet network cabling must be completed to Ethernet
standards.
• The Ethernet switch in the distribution board is not required if a
separate Cat5. cable is run from the main switch to each DCBM
DALI line controller.
CLIPCOM 21240 May 2010 2004
© Copyright Clipsal Australia Pty Ltd. The identified trademarks and copyrights are the property of Clipsal Australia Pty Ltd unless otherwise noted.
www.dalicontrol.com
Wiring
Typical Switchboard Layout
a.c. Supply
N
L
+V
B
-V
Notes:
Height
Width
93
78
93
78
Depth
Height
Width
Depth
56
Part Number
DCBM1-1608
92
216
63
36
DCBM2-1608
92
216
63
120
140
54
120
140
54
DCP24/30
93
78
56
DCBM2-0808
DCP24/60
93
78
36
DCBM2-1602
DCDALP200
90
17
58
DCDALP250
90
34
57
DCDALCI
100
50
30
CLIPCOM 21240 May 2010 2015
DCDALCI
BMxxxx-DALI Line Controller Ethernet Gateway
Dimensions (shown in mm)
DCP12/60
DCDALCI
A
DCDALPxxxxx
Part Number
DCP12/30
DALI-B
To Switches and Push Buttons, Occupancy and Light
Sensors, Security and Access Control Panels, etc.
RJ45 Ethernet
DCPxx/xx Power Supply
DALI-A
• DCDALPxxxxx should be separated by spacers to allow air flow
and avoid overheating.
• DCPxx/xx power supplies can power multiple BM-DALI line
controllers and sensors, according to the accumulated load.
© Copyright Clipsal Australia Pty Ltd. The identified trademarks and copyrights are the property of Clipsal Australia Pty Ltd unless otherwise noted.
www.dalicontrol.com
Wiring
DALI DCDALxxxxx Wiring Overview
To CCT Breaker
Starter Socket
Socket or T-Piece
L
L
N
N
DA
DA
DA
DA
12VDC
IN0
IN1
IN2
IN3
OUT0
OUT1
GND
L
N
DCDALxxxxx
(1 Address)
DA
DA
DALI Control DCDAL Series
DCDALIO-0402 Room Controller
DCDALO-02 2-Channel Output Module
Input Circuit using 12V Relay
Input Circuit
Output Circuit
12V d.c.
12V d.c.
12V d.c.
R1
R2
Load
(12V Relay Coil)
R1
INx
Relay (12V Coil)
R2
INx
OUTx
C
C
GND
Internal Circuit
CLIPCOM 21240 May 2010 2006
GND
External Components
Internal Circuit
External Components
GND
Internal Circuit
© Copyright Clipsal Australia Pty Ltd. The identified trademarks and copyrights are the property of Clipsal Australia Pty Ltd unless otherwise noted.
External Components
www.dalicontrol.com