HID PRODUCTS DIMMING SYSTEMS HID PRODUCTS DIMMING SYSTEMS
AVAILABLE DIMMING OPTIONS
STANDARD
F
Magnetic power supply unit
Electronic power supply unit
UPON REQUEST
DA DAC PLM DB DALI D10
X
X
X
X
X
X
X
X
X
X
X
X
DR
X
STANDARD DIMMING OPTIONS
DA (DIM-AUTO) OPTION
AUTOMATIC LIGHT FLUX REGULATION The power supply unit is configured using an automatic dimming profile which allow to fully exploit
the maximum light intensity during the first and last few hours of system operation, thereby reducing
the energy consumption in the middle of the night when a lower level of illumination is enough. The
reduction profile automatically adapts to the duration of the night-time period during the year.
DAC (DIM-AUTO CUSTOM) OPTION
The power supply is configured using a custom dimming profile, fully customized by the user up to 5
levels in 4 steps.
In case of magnetic ballast only two power levels are provided: full power and low power (whose
schedules reduction can be adjusted by means of dip-switch switches).
PLM OPTION
LIGHT FLUX REGULATION BY MEANS OF POWER LINE COMMUNICATION
Light flux reduction can be associated with punctual and remote monitoring of the single device via
the power line communication remote control. This option, used in conjunction with an LCU (Light
Control Unit), makes possible to control the single lighting point, allowing the creation of customized
lighting scenarios.
AEC ILLUMINAZIONE S.r.l. - 52010 SUBBIANO (AR) - ITALY - Via Righi, 4 Zona Industriale Castelnuovo
Cap.Soc. € 1.560.000,00-REA AR 72908-C.F./P.IVA Reg.Imp.AR N° 00343170510-Iscrizione Registro AEE IT08020000000863-Società aderente al consorzio Ecolight
HID PRODUCTS DIMMING SYSTEMS More complex remote control boards can be used, by means of a wireless or GSM/GPRS network,
to remotely monitor the energy consumption of the system and provide fault alerts without on-site
maintenance procedures.
LCU The Light Control Unit offers a flexible system control. The reduction profile can be customized by
means of local or remote programming. The luminaires can be divided into sub-groups with different
dimming profiles. Possibility of using an astronomical clock interfacing with external switching
devices. Simplified installation, wiring and testing. Programming software free of charge. AEC ILLUMINAZIONE S.r.l. - 52010 SUBBIANO (AR) - ITALY - Via Righi, 4 Zona Industriale Castelnuovo
Cap.Soc. € 1.560.000,00-REA AR 72908-C.F./P.IVA Reg.Imp.AR N° 00343170510-Iscrizione Registro AEE IT08020000000863-Società aderente al consorzio Ecolight
HID PRODUCTS DIMMING SYSTEMS OPTIONS UPON REQUEST (SUBJECT TO FEASIBILITY CHECK)
D10 (DIM-10) OPTION
FLUX ADJUSTMENT VIA 1-10V ANALOGUE CONTROL
This profile allows the lighting device luminous flux adjustment via an analogue voltage signal
between 1V and 10V, corresponding to the minimum and maximum brightness levels. The device is
designed for the connection of one multicore cable featured by 4/5 poly (L-N-1/10V-PE).
DALI (Digital Addressable Lighting Interface) OPTION
FLUX ADJUSTMENT VIA DIGITAL INTERFACE
DALI is the standard digital technology for the management of luminaires; it is based on a digital
signal capable of univocally addressing up to 64 modules on the same bus. The device is designed
for the connection of one multicore cable featured by 4/5 poly (L-N-DALI-PE).
DB (DIM-BIP) OPTION
Bi-power light flux adjustment with pilot cable
Option mainly designed for underpasses or small projects where a simple and synchronized flux
reduction is required. The device is supplied with a bi-power switch which will establish an
operati¬ng regime at full or reduced power, according to the presence or absence of voltage on the
additional conductor (pilot cable).
DR (DIM-REG) OPTION
Light flux adjustment with flux controllers
This option makes it possible to use HID devices with an electronic power supply in systems with a
flow controller for traditional discharge devices: The electronic power supply follows up the voltage
adjustment carried out within the system, regulating the lamp flow as a result. Operation is only
guaranteed if amplitude modulation controllers are used instead of phase cut controllers.
AEC ILLUMINAZIONE S.r.l. - 52010 SUBBIANO (AR) - ITALY - Via Righi, 4 Zona Industriale Castelnuovo
Cap.Soc. € 1.560.000,00-REA AR 72908-C.F./P.IVA Reg.Imp.AR N° 00343170510-Iscrizione Registro AEE IT08020000000863-Società aderente al consorzio Ecolight
HID PRODUCTS DIMMING SYSTEMS ADDITIONAL OPTIONS
FLC OPTION
Light flux recovery
The natural deterioration of the light flow produced by the lamp can be offset by progressively
increasing the power supplied during operation. This option guarantees a virtually constant light flow
output. The lighting system can therefore be designed while taking account of a maintenance factor
which is higher than that usually used with the standard product, offering instant savings in terms of
the energy consumed and/or the initial cost of the system. The FLC option also means a greater
useful life can be taken into account for the system.
SYSTEM FEATURES AND DIMMING SYSTEM INSTALLATION:
DA/
DAC
Independent adjustment system
Centralized adjustment system (switch /control unit /cabinet)
Remote reduction profile change
Use of additional cables
Remote management software required
Configuration software free of charge (LED and HID electronic systems only)
Interfacing with external regulation systems (e.g. PIR sensors, traffic sensors, switches)
Commissioning by specialist personnel
PLM/
LCU
PLM
DB
DR
DALI
D10
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
AEC ILLUMINAZIONE S.r.l. - 52010 SUBBIANO (AR) - ITALY - Via Righi, 4 Zona Industriale Castelnuovo
Cap.Soc. € 1.560.000,00-REA AR 72908-C.F./P.IVA Reg.Imp.AR N° 00343170510-Iscrizione Registro AEE IT08020000000863-Società aderente al consorzio Ecolight
X