VIEW "A" VIEW "B" SIDE VIEW

advertisement
INSTALLATION
INSTRUCTIONS
P/C
FIXTURE TYPE_______
510637-00
DO NOT MODIFY OR ALTER THIS PRODUCT IN ANY WAY, OR INSTALL IN ANY FASHION
WHICH IS CONTRARY TO THE INSTRUCTIONS CONTAINED HEREIN.
IF YOU HAVE ANY QUESTIONS REGARDING THIS PRODUCT OR THE INSTALLATION OF IT,
PLEASE CALL LITECONTROL ENGINEERING AT 781-294-0100.
3L, 4L & 6L-W-D (or ID)
FIXTURE ASSEMBLY
PG.1 OF 2
1 7/8"
3 3/16" (3L) 4 3/8" (4L) and 5 3/8 (6L)
WALL REF.
WALL BRACKET
OUTLINE
7"
WALL BRACKET
OUTLINE
= 2" DIA ELECTRICAL
FEED HOLE
4 1/2"
4 1/2"
24"
= 5/16" x 1 13/32"LG MOUNTING SLOTS
1/2"
2 3/4"
1 7/8"
END CAP
1 7/8"
WALL BRACKET
CROSS SECTION 3L, 4L & 6L-W-D
8"
CROSS SECTION 3L, 4L & 6L-W-ID
36",48",60",72",96"
FIXTURE
GENERAL NOTES: (READ SHEETS COMPLETELY BEFORE STARTING)
1. Leave protective wrapping material on fixture until fixtures are mounted: This will protect finish from damage.
2. Fixtures are supplied with factory installed branch circuit wiring. Refer to supplemental instruction sheet for making connections.
3. Fixtures are attached with Wall Bracket(s) (Shipped Separately) over a finished wall surface.
Two brackets are required for 36", 48", 60",72" and 96" fixture lengths. One bracket for 24" fixture is required.
SIDE VIEW
VIEW "B"
Refer to installation instructions for mounting to wall. Approximate weight of fixture is 3 1/2 lbs per foot of length.
INSTRUCTIONS:
#6-32 X 1/2
MACHINE
SCREW
1. MOUNTING INDIVIDUAL FIXTURES:
Wall Brackets: (shipped separately)
A) Locate wall brackets along a straight line on the wall per dimensions shown in SIDE VIEW.
B) Peel back foam wrapping and remove Led Modules by removing (2) 8-32 machine screws two screws are retained
with locking nuts (See View B)
Modules have nylon tethers attached to them at the Factory which allow them to hang down while hanging the fixtures.
C) Attach End Cap mounting plates (shipped separately) to each end with # 6-32 machine screws provided. See View "A".
D) Lift fixture and mount to wall brackets with 1/4-20 hexhead nuts provided.
Bring the electrical feed into fixture wireway and make all the wiring connections.
GO TO STEP 3 ON PAGE 2.
FIXTURE
8-32 x 3/8 MACH
SCREWS
litecontrol.com
LED REFLECTOR ASSY
SNAP IN DIFFUSER
DIE CAST
END CAP
END CAP MOUNTING
PLATE
VIEW "A"
FORM B520140-4
INSTALLATION
INSTRUCTIONS
P/C
FIXTURE TYPE_______
510637-00
3L, 4L & 6L-W-D (or ID)
FIXTURE ASSEMBLY
PG. 2 OF 2
DO NOT MODIFY OR ALTER THIS PRODUCT IN ANY WAY, OR INSTALL IN ANY FASHION
WHICH IS CONTRARY TO THE INSTRUCTIONS CONTAINED HEREIN.
IF YOU HAVE ANY QUESTIONS REGARDING THIS PRODUCT OR THE INSTALLATION OF IT,
PLEASE CALL LITECONTROL ENGINEERING AT 781-294-0100.
SCREW DIRECTION
LABEL
#6-20 ROW
MOUNTING
SCREW
FIXTURE ROW JOINT
LED REFL MOD
litecontrol.com
ROW JOINT
COVER PLT
VIEW "D"
#6-20 ROW
MOUNTING
SCREW
SNAP IN
DIFFUSER
EXTRUSION
BRACKET
FIXTURE
"MALE"
FIXTURE
"FEMALE"
VIEW "C"
FORM B520140-4
Download