Maintenance Tools Hydraulic Nuts ................................................................................... 684 Mounting Methods .......................................................................................................... 684 Dimensions ...................................................................................................................... 685 Hydraulic Pump ................................................................................. 687 Spanner Wrench ................................................................................ 688 Pressed Plates ................................................................................... 689 Pullers................................................................................................. 690 NSK .................................................................................................................................. 690 Sykes Pickavant .............................................................................................................. 693 TOLEDO ........................................................................................................................... 698 Workshop Tools.................................................................................. 701 Lubrication ......................................................................................... 705 Cable Ties........................................................................................... 710 Pliers ................................................................................................... 712 Screwdrivers ...................................................................................... 716 Socket and Spanner Sets .................................................................. 717 BSC Motion Technology 683 Hydraulic Nuts TOOLS Mounting Methods Below are three different ways to use Hydraulic Nuts. AFTER MOUNTING BEFORE MOUNTING 1 Axial Displacement Method Cb = Bench Clearance Cm = Mounted Clearance Cr = Clearance Reduction 1 Axial Displacement Method Ds = Starting Distance Da = Min. Axial Displacement X = Overhang after Installed Using Axial Displacement Pin: Using Axial Displacement Pin: Piston is ready to move the bearing by pushing against the inner ring. Piston has moved the bearing the minimum axial displacement. The Axial Displacement pin is flush with the back of the nut. 2 Straight Edge Method Using Straight Edge: Placing a straight edge such as a wrench will show a gap. 3 Dial Indicator Method Using Dial Indicator: Place a dial indicator on the back of the axial displacement pin. 684 BSC Motion Technology 2 Straight Edge Method Using Straight Edge: The gap has disappeared indicating the bearing has moved the minimal axial displacement. 3 Dial Indicator Method Using Dial Indicator: Watch the gauge to determine the axial displacement of the bearing. Hydraulic Nuts TOOLS Jack Out Bolt Bearing Bore Size *** Bore Bore Bore Sym bol (m m ) (inch) 10 50 1.9685 11 55 2.1654 12 60 2.3622 13 65 2.5591 14 70 2.7559 15 75 2.9528 16 80 3.1496 17 85 3.3465 18 90 3.5433 19 95 3.7402 20 100 3.937 21 105 4.1339 22 110 4.3307 n/a n/a n/a 24 120 4.7244 n/a n/a n/a 26 130 5.1181 n/a n/a n/a 28 140 5.5118 n/a n/a n/a 30 150 5.9055 n/a n/a n/a 32 160 6.2992 n/a n/a n/a 34 170 6.6929 36 180 7.0866 38 190 7.4803 40 200 708740 n/a n/a n/a n/a n/a n/a n/a n/a n/a 44 220 8.6614 n/a n/a n/a n/a n/a n/a n/a n/a n/a 48 240 9.4488 n/a n/a n/a 52 260 10.2362 Dimensions φ3.8” NPTF Plug Hydraulic Nut p/n Metric Inch Blank HMV()-1 HMV()Z-1 HMV()B-1 50 49 50 55 54 55 60 59 60 65 64 65 70 69 70 75 74 75 80 79 80 85 84 85 90 89 90 95 94 95 100 99 100 105 104 105 110 109 110 115 n/a 115 120 119 120 125 n/a 125 130 129 130 135 n/a 135 140 139 140 145 n/a 145 150 149 150 155 n/a 155 160 159 160 165 n/a 165 170 169 170 180 179 180 190 189 190 200 199 200 205 n/a 205 210 n/a 210 215 n/a 215 220 219 220 225 n/a 225 230 n/a 230 235 n/a 235 240 239 240 250 n/a 250 260 258 260 Wrench Crank Handle Dim ensions in m m d1 50.5 55.5 60.5 65.5 70.5 75.5 80.5 85.5 90.5 95.5 100.5 105.5 110.5 115.5 120.5 125.5 130.5 135.5 140.5 145.5 150.5 155.5 160.5 165.5 170.5 180.5 191 201 207 212 217 222 227 232 237 242 252 262 d2 84 89 95 101 107 112 117 122 127 133 138 143 149 154 159 164 170 175 180 186 191 198 204 209 215 227 239 251 256 262 267 273 280 285 291 296 307 319 d3 114 120 125 130 135 140 146 150 156 162 166 172 178 182 188 192 198 204 208 214 220 226 232 238 244 256 270 282 288 294 300 306 312 318 326 330 342 356 B 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 39 39 39 40 40 41 41 42 43 43 44 44 44 45 45 46 46 46 47 B1 4 4 5 5 5 5 5 5 5 5 6 6 6 6 6 6 6 6 7 7 7 7 7 7 7 7 8 8 8 8 8 8 8 8 8 9 9 9 D 72 76 81 88 95 100 106 110 116 122 126 130 136 141 146 151 156 161 166 171 176 183 190 195 200 212 230 241 247 252 258 263 269 274 281 285 296 308 E 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 C 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.5 13.5 14.0 14.5 14.5 15.0 15.5 16.5 17.0 17.0 17.5 17.5 18.0 18.5 18.5 19.0 19.0 19.5 20.0 Piston Stroke 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 6 6 6 6 7 8 8 9 9 9 9 9 10 10 10 11 Properties Piston Area 29 31 33 36 38 40 42 45 47 49 51 53 56 58 60 62 64 66 68 73 75 81 86 89 94 103 115 125 128 134 137 144 152 155 162 165 176 188 Mass (kg) 2.7 2.8 2.8 3.0 3.2 3.4 3.7 3.8 4.0 4.3 4.4 4.7 5.0 5.0 5.3 5.3 5.7 5.7 6.0 6.5 6.6 7.0 7.6 7.9 8.4 9.2 10.5 11.5 12.0 12.5 13.0 13.5 14.5 15.5 16.0 16.0 17.5 19.0 * Inch Threads for HMV49Z-1 to HMV258Z-1 are American National Form Class 3. ** Metric Threads for HMV50-1 to HMV200-1 are ISO 965/111-1980 tolerance class 6H. Metric Threads for HMV205-1 to HMV260-1 are ISO 2901-1977 tolerance class 7H. BSC Motion Technology 685 Hydraulic Nuts TOOLS Dimensions **If a seal needs replacing, the use of NSK’s jack out bolts make the task quick and easy. Bearing Bore Size *** Bore Bore Bore Sym bol (m m ) (inch) 10 50 1.9685 11 55 2.1654 12 60 2.3622 13 65 2.5591 14 70 2.7559 15 75 2.9528 16 80 3.1496 17 85 3.3465 18 90 3.5433 19 95 3.7402 20 100 3.937 21 105 4.1339 22 110 4.3307 n/a n/a n/a 24 120 4.7244 n/a n/a n/a 26 130 5.1181 n/a n/a n/a 28 140 5.5118 n/a n/a n/a 30 150 5.9055 n/a n/a n/a 32 160 6.2992 n/a n/a n/a 34 170 6.6929 36 180 7.0866 38 190 7.4803 40 200 708740 n/a n/a n/a n/a n/a n/a n/a n/a n/a 44 220 8.6614 n/a n/a n/a n/a n/a n/a n/a n/a n/a 48 240 9.4488 n/a n/a n/a 52 260 10.2362 Metric Thrad ** M 50x1.5 M55x2 M60x2 M65x2 M70x2 M75x2 M80x2 M85x2 M90x2 M95x2 M100x2 M105x2 M110x2 M 115x2 M120x2 M 125x2 M130x2 M 135x2 M140x2 M 145x2 M150x2 M 155x3 M160x3 M 165x3 M170x3 M180x3 M190x3 M200x3 Tr205x4 Tr210x4 Tr215x4 Tr220x4 Tr225x4 Tr230x4 Tr235x4 Tr240x4 Tr250x4 Tr260x4 Inch Threads * Nom inal Threads Diam eter per Inch 1.967 18 2.157 18 2.36 18 2.548 18 2.751 18 2.933 12 3.137 12 3.34 12 3.527 12 3.73 12 3.918 12 4.122 12 4.325 12 n/a n/a 4.716 12 n/a n/a 5.106 12 n/a n/a 5.497 12 n/a n/a 5.888 12 n/a n/a 6.284 8 n/a n/a 6.659 8 7.066 8 7.472 8 7.847 8 n/a n/a n/a n/a n/a n/a 8.628 8 n/a n/a n/a n/a n/a n/a 9.442 6 n/a n/a 10.192 6 Axial Displacem ent 1:12 (m m ) 1:12 (m m ) 1:30 (m m ) 1:30 (m m ) m in. m ax. m in. m ax. 0.45 0.55 0.60 0.70 0.70 0.85 1.75 2.15 0.75 0.90 1.90 2.25 0.90 1.10 2.25 2.75 1.00 1.30 2.50 3.25 1.10 1.40 2.75 3.50 1.30 1.60 3.25 4.00 1.40 1.70 3.50 4.25 1.60 1.90 4.00 4.75 *** Mounting directly on a tapered shaft or an adapter seeve. For inch sizes, if mounting on a removal sleeve, choose next smallest inch size hydraulic nut. For metric sizes, if mounting on a removal sleeve, choose next smallest metric size. n/a = ISO bearings and standard inch hydraulic nut size does not exist for mounting directly on a shaft or on an adapter sleeve. 686 BSC Motion Technology Hydraulic Pump TOOLS TYPE HSS HDS ELE AIR = = = = Hydraulic Single Stage Hydraulic Double Stage Electric Powered Pump Air Powered Pump TANK CAPACITY BASE NUMBER Small Large PUMP HSS SMALL NSK offers Hydraulic Pumps that inject oil into hydraulic nuts during bearing installation and simplify the bearing removal process by pumping oil between the inner ring and journal. NSK heavy duty pumps are offered in two sizes, are lightweight and come in a specially designed protective carrying case. Oil Displacement Max Usable Max Per Stroke Pump Working Oil Handle Piston Oil Outlet Description Pressure Capacity Effort Stroke Port Weight inch 3 1st Stage 2nd Stage lbs inch NPTF lbs psi inch 3 PUMP HSS Hand Pump LARGE Single Speed 10,000 48 0.15 24.4 0.98 3/8" - 18 16.5 PUMP HSS Hand Pump SMALL Single Speed 10,000 30.15 0.18 24.4 0.98 3/8" - 18 13.44 * All pumps include a relief valve set at 10,000 psi. ** All pumps come in kits which include a pump, hose, quick disconnect, coupler (nipple), gauge, tee, extra oil and NSK P/N** Pump Dimensions inch (mm) L W H 22.05 5.51 5.51 (560) (140) (140) 15.16 5.51 5.32 (385) (140) (135) a metal case. BSC Motion Technology 687 Spanner Wrench TOOLS SIZE BASE NUMBER 23-30 = fits AN 23-30 locknuts 30-40 = fits AN 30-40 locknuts 40-52 = fits AN 40-52 locknuts HN IMPACT 23-30 Spanner wrenches are a simple and inexpensive means of installing small size tapered bore bearings onto shafts and adapter sleeves. Because they clamp onto the slot in a locknut, they do not cause damage to the locknut which frequently occurs when using a hammer and keystock. NSK standard spanner wrenches are made from 1/4” (7mm) thick plates. The heads of impact spanner wrenches are made of forged steel, which is welded to a strong alloyed steel handle covered by easy grip rubber. LOCKNUT P/N** LOCKNUT SERIES LOCKNUT NUMBER 688 NSK impact-spanner wrenches are heavy duty and can withstand the impact force of a hammer. All wrenches come with a convenient hole for ease of storage or hanging. NSK IMPACT SPANNER WRENCH P/N KM HM..T HML..T HM30 HM31 AN-00 N-000 23-30 * * * * 24-30 026-032 HN IMPACT 23-30 30-40 * 41-42 * * 30-40 034-040 HN IMPACT 30-40 40-52 41-50 41-54 44-52 * 40-44 044-052 HN IMPACT 40-52 BSC Motion Technology Pressed Plates TOOLS Tri-Section Tri-Section Press Plates CK3-50 CK3-100 CK3-160 CK3-260 CK3-380 CK3-50 CK3-100 CK3-160 CK3-260 CK3-380 21304 22205 22211 23120 23032 61801 61805 61811 61820 61832 CK3-50 CK3-100 NN4920 CK3-160 NN4920 CK3-260 NN3020 CK3-380 NNU49323 Part Capacity Number ton A kN (imp) CK3-50 80 8 12 CK3-100 200 20 26 CK3-160 300 30 50 CK3-260 450 45 90 CK3-380 600 60 140 B 50 100 160 260 380 22310 22320 23232 23252 24176 6410 6320 6232 6252 6076 NN4120 NNU4132 NNU4152 NNU4176 WT Dimensions C D E F G kg mm 20 26 15 2 4 0.5 36 45 25 3 6 2.8 45 60 33 4 8 6.5 70 88 47 6 11 19.5 81 112 63 8 14 48.4 BSC Motion Technology 689 Pullers TOOLS NSK Series Style Type in = pump built in cylinder 4 = straightener 5 = pump separate of cylinder 6 = pusher kit blank = puller 3 = tri-section press plate 8 = pusher Special Feature blank = pump built in cylinder H = high capacity cylinder C = strong cobra jaw L = long jaw 3 = kit with tri-section press plate Base Number CK Pullers, pushers, straighteners and trisection press plates are useful in the quick, easy and safe installation and removal of bearings, rings, pulleys and gears. The use of these tools is helpful in protecting the shaft, bearings and surrounding equipment from damage. They also help reduce the potential for bodily harm to the operator. NSK’s family of pullers, pushers, straighteners and tri-section press plates come in a full range of sizes and come individually or in kits specifically matched to customer needs. NSK offers a hydraulic pusher, puller and tri-section press plate in a single heavy duty case making transportation and storage more convenient as well as reducing the possibility of lost parts. Pullers are available in noninterchangeable standard and high capacity designs. The high capacity design includes a high pressure cylinder and cobra jaw. Hydraulic pullers and pushers from NSK incorporate course threads which make it easier and quicker to assemble than competitive bearing removal products. 690 BSC Motion Technology 3 -6 in HCL Pullers TOOLS NSK PULLER PULLER/ STRAIGHTENER PUSHER CK-10in is sold separately from CK-104A BSC Motion Technology 691 692 CK-6sd CK-6in CK-6inL CK-6inHC CK-6inHCL CK-6in3 CK-6in3H CK-8in CK-8inL CK-8inHC CK-8inHCL CK-8in3 CK-8in3H CK-10in CK-10inL CK-10in3 CL-11inHC CK-11inHCL CK-11in3H CK-12inHC CK-12inHCL CK-15inHC CK-25 CK-25C CK-25CL CK-105 CK-105L CK-105HC CK-105HCL CK-135HC CK-135HCL CK-155HC CK-104 CK-104A CK-104B CK-130 CK8-270 CK8-270A CK8-270C CK8-270G Part Number Jaw** Cylinder Capacity Std. Cobra (kpsi) Case* ton (imp) Std. L S L 10 12 CB M PE W kN 60-65 6-6.5 • • • 60-65 6-6.5 • • • 60-65 6-6.5 • • • 100-105 10-10.5 • • • 100-105 10-10.5 • • • 60-65 6-6.5 • • • 100-105 10-10.5 • • • 80-85 8-8.5 • • • 80-85 8-8.5 • • • 120-125 12-12.5 • • • 120-125 12-12.5 • • • 80-85 8-8.5 • • • 120-125 12-12.5 • • • 150-155 15-15.5 • • • 150-155 15-15.5 • • • 150-155 15-15.5 • • • 200-205 20-20.5 • • • 200-205 20-20.5 • • • 200-205 20-20.5 • • • 250-255 25-25.5 • • • 250-255 25-25.5 • • • 300-305 30-30.5 • • • 400-405 40-40.5 • • • • 400-405 40-40.5 • • • 400-405 40-40.5 • • • 150-155 15-15.5 • • • 150-155 15-15.5 • • • 175-180 17.5-18 • • • 175-180 17.5-18 • • • 225-230 22.5-23 • • • 225-230 22.5-23 • • • 250-255 25-25.5 • • • 150-155 15-15.5 • 150-155 15-15.5 • 150-155 15-15.5 • • 80 8 • 120 12 • • 80 8 • • 120 12 • • • BSC Motion Technology • • • • • • • • • • • Reach Dimensions Spread Stroke A B C D E mm mm 152 30/150 55 11 6 22 32 53 152 30/200 82 11 6 22 32 83 190 30/200 82 11 10 25 51 83 182 280 82 11 6 22 32 113 220 280 82 11 10 25 51 113 152 30/200 82 11 6 22 32 83 182 280 82 11 6 22 32 113 190 30/250 82 11 10 25 51 83 229 30/250 82 14 10 29 51 83 220 305 82 11 10 25 51 113 259 305 82 14 10 29 51 113 190 30/250 82 11 10 25 51 83 220 305 82 11 10 25 51 113 229 280 82 14 10 29 51 83 300 280 82 30 28 33 75 83 229 280 82 14 10 29 51 83 259 356 82 14 10 29 51 113 300 356 82 30 28 33 75 113 259 356 82 14 10 29 51 113 300 406 110 30 28 33 75 140 375 406 110 27 36 38 78 140 375 50/540 110 27 36 38 78 170 250 165 405 800 250 30 38 28 76 635 1200 250 30 38 28 76 229 280 82 14 10 29 51 83 300 280 82 30 28 33 75 83 259 356 82 14 10 29 51 113 300 356 82 30 28 33 75 113 300 406 110 30 28 33 75 140 375 406 110 27 36 38 78 140 375 540 110 27 36 38 78 170 150 100/410 82 205 100/410 82 32 17 35 150/205 100/410 82 32/60 17 35 -450 36-130 30 188 90 230 30 -440 58-270 82 35 193 90 230 58 -440 58-270 82 -440 58-270 82 •(CK3-160) -440 58-270 82 Safety Tri-section Bag*** Pusher Puller Press Plate B M • • • • • • • • • • • • •(CK3-100) • • •(CK3-100) • • • • • • • • • • •(CK3-160) • • •(CK3-160) • • • • • • •(CK3-160) • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 160 130 60 60 60 60 70 70 74 42 42 42 42 42 42 42 50 50 50 50 50 50 60 60 60 60 60 60 70 70 74 110 F G WT kg 25 5.0 25 5.5 25 6.3 25 6.7 25 7.6 25 9.1 25 9.5 28 7.3 28 8.1 25 9.2 25 10.7 28 13.8 25 15.7 35 9.3 35 12.9 35 15.8 35 12.0 35 14.2 35 18.6 45 19.3 45 24.3 55 32.4 71 88.7 57.2 72.2 35 13.8 35 17.3 35 16.4 35 18.6 45 23.8 45 28.7 55 31.6 60 10.4 9.1 60 14.6 35 7.5 35 12.3 15.4 14.4 30.9 TOOLS Pullers NSK Pullers TOOLS Sykes Pickavant HYDRAULIC PULLERS 1500 Series Triple Leg Hydraulic Pullers Standard Leg Part No. Puller Spread Max Puller Reach Max Ram Extension 153400 100mm 100mm 50mm 153600 150mm 150mm 100mm 150mm 153700 150mm 250mm 153800 200mm 100mm 150mm 153900 250mm 250mm 150mm Each part number contains 1 x Hydraulic Ram 1 x Triple Head Assembly 1 x Ram Extension 3 x Legs 1500 Series Puller and Separator Kits • Use 1500 series hydraulic ram to deliver 8 tonnes pulling force with ease. • Strong, drop forged steel legs tighten as load is increased for safe, positive grip. • Separators have tapered edge for insertion behind close fitting bearings, gears etc. Standard Leg Part No. Puller Reach External Spread External Reach Max Max - Min Max 155200 Puller Spread Max 150mm 150mm 105 - 20mm 876mm 155208 200mm 200mm 105 - 20mm 876mm 155305 250mm 250mm 105 - 10mm 876mm 155200 Part No Hydraulic Puller / Separator Kit 155200 • Makes 4 hydraulic pullers and 1 separator. • In lockable metal case. Part No Hydraulic Puller / Separator Kit 155208 • Makes 6 hydraulic pullers and 1 separator. • In lockable metal case. Part No Hydraulic Puller / Separator Kit 155305 • Two puller panels combined - 155105 plus 193105. • Makes 8 hydraulic pullers, 1 mechanical puller, 2 separators and 7 split collet internal extractors. • Metal storage/display panel complete with hooks (also available separately - see individual panels). BSC Motion Technology 693 Pullers TOOLS Hydraulic MECHANICAL KIT BUILD Twin/Triple Leg Pullers Extractor Kit Build Part No. 082705 Part No. 082805 Part No. 082900 Part No. 082903 Part No. 095800 Part No. 095801 Part No. 084200 Part No. 095802 Multipull® Blind Housing Bearing Removers Part No. 098000 1 5.5mm 1 5.5mm 2 6mm 2 6mm Part No. 095803 3 8mm 3 8mm Part No. 098100 1 5.5mm 4 9mm 1 5.5mm 4 9mm 2 6mm 5 11mm 2 6mm 5 11mm 3 8mm 3 8mm 6 12.5mm 6 12.5mm Part No. 095803 Part No. 098200 7 16mm 10 25mm 694 BSC Motion Technology 7 16mm 10 25mm 8 19mm 8 19mm 9 22mm 11 28mm 11 28mm 12 31.75mm 9 22mm 12 31.75mm Pullers TOOLS Hydraulic HYDRAULIC KIT BUILD 1500 Series Triple Leg Hydraulic Pullers Part No. 153400 Part No. 153600 Part No. 153800 Part No. 153900 Part No. 153700 1500 Series Puller and Separator Kits Part No. 155200 Part No. 155208 BSC Motion Technology 695 Pullers TOOLS Mechanical MECHANICAL PULLERS Twin/Triple Leg Pullers • Twin and triple beams and double ended legs for a wide range of pulling options. No. of Puller Combinations Leg Style Part No. Max Puller Spread 082705 150mm 80mm 4 082805 200mm 140mm 4 084900 200mm 140mm 8 084903 200mm 140mm 8 Max Puller Reach Double Ended Reversible Double ended legs for internal and external use Double Ended Reversible & Standard Adjustable 084200 350mm 380mm 12 3 positions, adjustable legs for increased pulling options Bearing Separators • Individual separators for removing and refitting bearings, etc. Part No Part No. 095000 External Spread Max -Min 55mm 095100 105 - 20mm 095200 140 - 35mm 095300 175 - 50mm Usage 095000 Can be used with 083000 Twin Leg Puller or 094000 Twin Leg Pulling Unit. 095100 Use with 083100 Twin Leg Puller. 095200 Can be used with 083200 and 083300 Twin Leg Pullers. 095200 Can be used with Sykes-Pickavant ‘Loadstar’ Heavy Duty Pullers and also 1200 and 1600 series pullers. Internal Extractor Kits • Extract components quickly and efficiently when conventional pullers cannot be used. • Removes gears, bearings, pinions, oil seals etc. • Can be upgraded for twin/triple leg pulling. Part No. 095801 095804 095802 095803 095800 696 External Spread Max -Min 13mm 6mm 22.5mm 8mm 30mm 13mm 60mm 30mm 60mm 6mmm No. of Split Collet Extractors 3 4 3 3 9 BSC Motion Technology Pullers TOOLS Mechanical MECHANICAL PULLERS Extractors and Pulling Units Part No. 095805 Twin Beam Pulling Unit Part No. 085421 Slide Hammer Assembly - 1kg • Twin beam mechanical puller for use with Sykes-Pickavant split collet type internal extractors. • For use with Sykes-Pickavant split collet type internal extractors. • Hammer displacement 220mm. • Hammer weight 1kg. Split Collet Internal Extractors Part No. 095809 095810 095811 095812 095813 Internal Spread Max -Min 8.5mm 6mm 11mm 8mm 13mm 10.5mm 18mm 13mm 22.5mm 18mm Part No. 095814 095815 095816 095817 Internal Spread Max -Min 30mm 22.5mm 38mm 30mm 50mm 38mm 60mm 50mm Multipull® Blind Housing Bearing Removers These special pullers will remove blind housing bearings without the need to dismantle machinery or remove the running shaft. • Positive seating allows even tension on inner and outer bearing rings, reducing resistance. • Stabilisers reduce sideways movement and self-centre the puller. • 3 kits cover a wide range of ISO bearings. (To identify kit for bearings without an ISO reference, refer to puller spread and adapter diameter). 098100 098000 Part No. Max Spread Min Spread Adaptor Dia. Puller Reach mm mm mm mm 098000 95 20 5.5 - 8 125 098100 117 20 5.5 - 12.5 415 098200 210 56 16 - 31.75 490 ISO Bearing Designation 098000 6004 - 6010 6299 - 6205 6300 - 6302 098100 6004 - 6015 6200 - 6211 6300 - 6307 6403 - 6404 098200 6212 - 6222 6308 - 6319 6405 - 6414 098200 BSC Motion Technology 697 Pullers TOOLS TOLEDO MECHANICAL PULLERS Toledo Mechanical Pullers are manufactured from drop forged Chrome Vanadium alloy steel. Designed for easy removal of bearings, pulleys, gears and sprockets. All Toledo Mechanical Pullers are double ended and available in two or three leg. Suitable for internal and external applications. Twin Leg Pullers Triple Leg Pullers Part No. Spread Reach Part No. Spread Reach 222030 75mm 60mm 223030 75mm 60mm 222040 100mm 70mm 223040 100mm 70mm 222060 150mm 120mm 223060 150mm 120mm 222080 200mm 175mm 223080 200mm 175mm 222100 250mm 190mm 223100 250mm 190mm 222120 300mm 215mm 223120 300mm 215mm Adjustable Twin Leg Sliding Beam Pullers • Drop forged Chrome Vandium alloy steel. • Reversable legs suitable for internal and external applications. Part No. 245460 Long Jaw Bearing Puller • Designed for internal/external applications requiring reach up to 300mm and spread capacity 10-15mm. • Drop forged hardened alloy steel. Part No. Spread Reach 232080 80mm 90mm 232120 120mm 90mm 232160 160mm 140mm Part No. Spread Reach 232200 200mm 140mm 245460 10-50mm 300mm Part No. 221000 Mechanical Bearing Separator Puller Set • Complete with two bearing separators (30-50mm, 50-75mm). • Designed for access behind bearing for easy bearing removal. Part No. 222000 Mechanical Bearing Puller Set • Complete wit bearing separator, main rods, extension rods and beam designed for access behind bearings utilising a mechanical forcing screw (Separator Capacity 75-105mm). • Suitable for large bearing removal. Contents Contents 1 x Forcing Screw 1 x Forcing Screw 4 x Extension Rods 2 x Extension Rods 1 x Beam 1 x Beam 4 x Main Rods 2 x Main Rods 2 x Separators 1 x Separators 1 x Thread Reducer 698 BSC Motion Technology Pullers TOOLS Part No. 224000 Mechanical Bearing Separator Puller Set • Designed for small bearing removal. • Mini puller designed for small bearing removal, electric motors etc. Contents 1 x Forcing Screw TOLEDO Part No. 225000 Mechanical Twin Pull Puller Set • Enables removal of bearing where access is limited. • Designed for small bearing removal, electric motors etc. • Spread: 20-95mm Reach: 125mm 2 x Extension Rods Contents 1 x Beam 1 x Forcing Screw 2 x Main Rods 2 x Extension Rods (small) 2 x Legs 1 x Beam 1 x Bearing Separator 2 x Main Rods 2 x Extension Rods (large) 6 x Insert Adaptors Part No. 246600 Micro Adjustable Bearing Puller • External puller designed for rapid bearing removal of a wide range of applications, including electrical motors, starter motors, alternator bearings, pumps, domestic appliances and power tools. • Self centres under load. • Spread: 19-45mm Reach: 73mm Part No. 246300 Collet Puller Set (8 Collets) • Split collet slide hammer internal bearing puller where access exists in centre of bearing. • Expanding split collet tightens to grip on underside of bearing (complete with 8 sizes of collets). Bearing Separators • Designed for removing gears and bearings where access is available behind the item. Two knife edges ensure a secure pulling surface. • Drop forged hardened alloy steel, used in conjunction with 2 leg mechanical pullers, hydraulic pullers or sliding beam applications. Part No. Capacity 245040 20-40mm 245050 30-50mm 245075 50-75mm 245105 75-105mm 245150 105-150mm BSC Motion Technology 699 Pullers TOOLS TOLEDO HYDRAULIC PULLERS Toledo Hydraulic Pullers are manufactured from the highest quality materials. All legs and bearing separators are drop forged Chrome Vanadium alloy steel. Designed for easy removal of bearings, pulleys, gears and sprockets. Part No. 266000 Heavy Duty Hydraulic Bearing Puller Set Combination Twin / Triple Leg Pullers • Toledo hydraulic pullers combination 2/3 leg puller offer the versitility of either a twin or triple puller. • The hydraulic ram ensures maximum force with minimal effort. Part No. Spread Reach 265040 50-100mm 100mm 265060 75-150mm 150mm 265080 100-200mm 200mm • Heavy duty set complete with bearing separator, main rods, extension rods and beam. • Designed for access behind bearing utilising the 10 tonne hydraulic ram (separator capacity 105-150mm). • Suits large bearing removal.. Contents 1 x Ram 2 x Main Rods 5/8” 2 x Extension Rods 5/8” 1 x Beam 1 x Separator 1 x Nose Piece Set (3 pce) 1 x Adaptor Part No. 267000 Hydraulic Bearing Puller Set • Toledo hydraulic puller set complete with bearing separator, main rods, extension rods and beam. • Designed for access behind bearing utilising the 10 tonne hydraulic ram. (Separator capacity 75-105mm). • Ideal for general maintenance. Contents 1 x Ram 2 x Main Rods 1/2” 2 x Extension Rods 1/2” 1 x Beam 1 x Separator 1 x Nose Piece Set (3 pce) Part No. 265000 Hydraulic Bearing Puller Set • Toledo hydraulic bearing puller set complete with bearing separator, main rods, extension rods, twin/triple head, beam and legs to build 4”, 6”, 8” two and three leg hydraulic pullers. • Ideally suitable for Industrial, Automotive, Agricultural and Marine applications and for general maintenance. • Separator capacity 75-105mm. Contents 1 x Ram 2 x Main Rods 1/2” 2 x Extension Rods 1/2” 1 x Beam 1 x Center Nut 1 x Separator 1 x Twin Head 1 x Triple Head 1 x Nose Piece Set (3 pce) 9 x Legs 700 BSC Motion Technology Workshop Tools TOOLS Spare Parts Cleaning Brush Part No. 301004 Part No. 301019 Pocket Magnetic Pick-up Tool • Extends from 125mm to 635mm. • Magnet capable of picking up 2.5kg. • Ideal for cleaning engine and transmission spares, brake parts and bearings. • 260mm x 25mm. Air Blow Gun Part No. 301005 • High impact plastic body, built-in hanger slot. • Angle tip 100mm. • Improved valve and comfortable lever control. • Inlet thread size 1/4” NPT. • Stainless steel body, 150mm long. • Lever actuated in conjunction with a ratchet type collar . to 5mm. Magnetic Stainless Steel Tray • 150mm x 38mm deep with strong in-built magnet. • Stow small parts, nuts, bolts and screws neatly and securely during dismantle and Part No. 301033 Tube Cutter • Hardened SK2 cutting wheel. • Wide dual rollers provide neat, square cuts. • Suitable for plastic, brass, copper, aluminium, and mild steel tubing between 3-30mm. reassembly . Gasket Scraper Part No. 301007 • Removes gasket residue, carbon Oil Seal Remover Scraper and Hook Set Part No. 301008 • Useful trade quality set. • Two sizes of scraper for scraping jobs in Description Part No. 301157 Feeler Gauge • 26 Blade Cranked Metric/Imperial. • Cranked blade 45o angle allows open or confined spaces. • Pick it, prod it, scratch it! Length 1 Multi Purpose Scraper 285mm 1 Multi Purpose Scraper 210mm 1 Scratch Awl 200mm 1 Cotter Pin Puller 225mm 1 Radiator Hose Remover 175mm Part No. 301009 Part No. 301042 • Removes oil and grease seals. • Complete with two removal hooks. • Length 310mm. and ingrained dirt. • Ideal scraping tool. • Size: 280 x 25mm Qty Hose Crimping Tool 150mm • Can accomodate hose from 12mm Fast, safe and easy to use. Part No. 301006 Part No. 301026 Stethoscope • Economical sonic diagnostic unit, locates access to restricted areas. • Size range (metric) 0.127mm-0.762mm and (imperial) 0.003”-0.030” Part No. 301160 Feeler Gauge • 16 Blade Metric/Imperial. • Size range (Metric) 0.05mm-0.38mm and (Imperial) 0.002” - 0.015” noise in machinery, engines, compressors, transmissions and drive trains etc. • 740mm long, 220mm probe extension. Thread Files Part No. 301011 Pocket Telescopic Mirror • Restoration tool for damaged or corroded threads. • Repairs almost any diameter bolt or stud. • Handles left or right handed threads. • 230mm long, ideal for working in confined areas. • Telescopic body extends from a pocket size 184mm to 500mm. • 25mm x 50mm oval swivel mirror head. Part No Description 301065 Metric 0.80, 1.00, 1.25, 1.5, 1.75, 2.00 and 3.00 Pitch sizes 301066 SAE 24-20-18-16-14-12-11-10 BSC Motion Technology 701 Workshop Tools TOOLS Part No. 301075 Stud Extractor Set • Six piece set. • Quick and easy way to remove broken studs. • SAE/Metric. Aviation Snips • Manufactured with drop forged, Chrome Moly steel. • Blades are scientifically heat treated for strength, toughness and durability. • Cuts up to 18 gauge, cold rolled sheet steel. • Double serrated blades. Part No. Description Colour Left Cut Red 301121 Straight Cut Yellow 301122 Right Cut Green 301120 Part No. 301083 Pry Bar Set 4 piece • Manufactured from top quality alloy steel for strength and durability. • Four piece set containing lengths: 200mm, 300mm, 450mm and 600mm. Adjustable Wrenches • Fully hardened and tempered. • Chrome Vanadium steel. Scribers • Double ended with knurled nurled body. • For marking and scoring. ring. Part No. Description Length MS7 Standard Scriber 190mm Heavy Duty Scriber 230mm MSH8 Torque Wrenches • • • • Slim head, reversible, click stop type. Heavy duty cam. Locking handle mechanism. Ideal for automatic transmission service. Part No. Dual Scale 301097 20-200 ins/lbs 2.5-25 Nm 1/4” Dr 301098 10-80 ft/lbs 12-108 Nm 3/8” Dr 301099 10-150 ft/lbs 12-203 Nm 1/2” Dr Part No. 301107 Size Part No. Length 88100 100mm Jaw Opening 88150 150mm 21mm 88200 200mm 25mm 13.5mm 88250 250mm 29mm 88300 300mm 34.5mm 45mm 88375 375mm 88450 450mm 55mm 88600 600mm 64mm Part No. MG10 Multi Grip Plier • Drop forged alloy steel. • Length 250mm. Socket Rail Holder • Colour coded socket organiser. • Easy identification Locking Grip Pliers of missing tools. • Drop forged alloy steel. Part No. Length VG180 180mm VG250 250mm Part No. 301108 Spanner Rack Organiser • High impact plastic. • Ideal for wall, shadow board or tool chest. • Suitable for open end, ring or combination spanners. • 300mm overall length. Part No. 301141 Circlip Plier Set Replacement Tips • Designed to exchange jaws easily. • Internal and external use. • Complete with 90 o, 45o and two Hex Key Ball Point Setss • Long style with ball points. • Available in Metric and AF. Part No. HKM HKAF 702 Description 7 piece metric 7 piece AF straight tips (1.2mm & 1.5mm) Part No. Size 2.5mm - 10mm 3/32” - 3/8” BSC Motion Technology Description 301144 Tips straight 1.2mm 301145 Tips straight 1.5mm 301146 Tips Angle 90 1.5mm 301147 o o Tips Angle 45 1.2mm Workshop Tools TOOLS Circlip Pliers Bearing & Oil Seal Installation Kit Part No. 301350 • Professional quality. • Heat-treated, drop forged steel. • Easily removes and installs circlips. • Eliminates damage to bearings and seals. • Cones may be used either side. • Comprising nine tapered driving 301125 cones between 40 and 80mm plus Part No. Decription Length 301125 Internal Straight tips 127mm 301126 Internal 90 o tips 127mm 301127 External Straight tips 127mm a screw attachable driver shaft of 140mm in length. • Compact, fully functional kit. 301126 301128 External 90 tips 127mm Code 301129 Internal Straight tips 177mm 1 301351 40mm 301130 o Internal 90 tips 177mm 2 301352 44mm 301131 External Straight tips 177mm 3 301353 50mm 301354 60mm o 301127 Part No Size 301132 External 90 tips 177mm 4 301133 Internal Straight tips 228mm 5 301355 63mm 301134 o Internal 90 tips 228mm 6 301356 65mm 301135 External Straight tips 228mm 7 301357 72mm 8 301358 76mm 9 301359 80mm 10 301360 140mm 301136 o o External 90 tips 301128 228mm Heavy Duty Circlip Pliers Straight Tips 301137 Part No. Decription Length 301137 10-25mm range 152mm 301138 18-48mm range 203mm Heavy Duty Circlip Plier Set Part No. 301800 • Manufactured from heavy gauge tempered steel. • Converts to internal and external. • Set contains one Internal and one External Circlip Plier. • Replaceable tip set features 16 different arrangements for the safe and easy removal and replacement 301138 of circlips, internal and external. • Spread of 75mm, length of 270mm. Heavy Duty Circlip Pliers 90o Tips • Manufactured from heavy gauge tempered steel. • Converts to internal and external. Part No. Decription 301139 Length 301139 10-25mm range 127mm 301140 18-48mm range 177mm 301140 Part No. Tip Size Tip Angle Qty Part No. Tip Size Tip Angle 301801 2.8mm Straight 2 301805 3.0mm Straight 2 Qty 301802 2.8mm 15 o 2 301806 3.0mm 15 o 2 301803 2.8mm 45 o 2 301807 3.0mm 45 o 2 301804 2.8mm 90 o 2 301808 3.0mm 90 o 2 Stainless Steel Rules • Highest Precision, hardened stainless steel. • Accurate to JIS B 7516 - Grade one specifications. Satin chromed for rapid reading. • Markings photographically etched. Each rule supplied in protective pouch. Metric and Imperial Stainless Steel - Single Sided Part No. 150A6 Metric and Imperial Stainless Steel - Double Sided Part No. Length Width 150B6 150mm 15mm Description Length 150mm Width 15mm Description One Square and one rounded end with hanging hole Metric Stainless Steel - Single Sided Part No. Length Width 150BM 150mm 15mm 30012 300mm 25mm 300M 300mm 25mm 60024 600mm 30mm 600M 600mm 30mm 100036 1000mm 35mm 1000M 1000mm 35mm One Square and one rounded end with hanging hole Description One Square and one rounded end with hanging hole BSC Motion Technology 703 Workshop Tools TOOLS Part No. 301181 Heavy Duty Pin Punch Set • Made from high quality carbon steel. • Heavy duty tool roll. • Set of seven. Part No. 301183 Heavy Duty Chisel Set Part No. 301184 Chisel and Punch Set • Made from high quality carbon steel. • Heavy duty • Set of seven. Punch and Chisel Set • High quality alloy steel chisels and carbon steel punches. • Heavy duty tool roll. • Set of 13. 704 Extra Long Pin Punch Set • Made from high quality carbon steel. • Heavy duty tool roll. • Set of five. • Made from high quality carbon steel. • Heavy duty tool roll. • Set of six. Part No. 301185 Part No. 301182 BSC Motion Technology C Hook Wrenches • Designed for use with slotted retaining rings • The hinge facility allows use on a range of diameters • Use on castellated nuts on hydraulic equipment or othe rmachinery with slots around the circumference. Part No. Decription 315150 Standard Size 315151 Standard 1 1/ 4” - 3” 315152 Standard 2” - 4 3/ 4” 315153 Standard 4 1/ 2” - 6 1/ 4” 315154 Pin Style 315155 Pin Style 1 / 4” - 3” 315156 Pin Style 2” - 4 3/ 4” 3 3 / 4” - 2” / 4” - 2” 1 Lubrication TOOLS TOLEDO GREASE GUNS AND ACCESSORIES Part No. 305221 Heavy Duty Pistol Grease Gun • • • • Part No. 305222 Deluxe Mini Pistol Grease Gun For use in confined or restricted spaces Release air by a half turn of the head assembly Extra port for adding bulk loader fitting Heavy duty aluminium die cast head with non-slip textured powder coated finish and plated pistol handle • Single hand operated pistol grip grease gun with convenient pull type operating mechanism • Textured powder coated finish for non-slip grip Outputs: Delivers 0.4g per stroke (0.6oz per 40 strokes) Output: Delivers 0.4g per stroke 0.6oz per 40 strokes) Pressure: 3,500 PSI (240 Bar) Pressure: 5,000 PSI (345 Bar) Multiple Loading Aluminium die cast head has 2 output parts. Front part generally used for regular greasing applications. Multiple Loading Cartridge Suction Cartridge Suction PartNo. Description Cartridge Capacity Bulk Capacity Thread PartNo. Description Cartridge Capacity Bulk Capacity Thread 305221 With 100mm(4”) Steel Extension, 300mm(12”) Flexible Hose and 4 Jaw Coupler 450g 650cm3 1/8” BSPT 305222 With 100mm (4”) Steel Extension and 4 Jaw Hydraulic Coupler 85g 120cm3 1/8” BSPT Part No. 305219 Heavy Duty Lever Action Grease Gun Part No. 305227 Suction Gun Single piece aluminium die cast head for leak proof operation • Heavy duty grease guns designed for continuous and demanding industrial applications • Texture powder coated finish for non-slip grip Output: Delivers 1g per stroke (1oz per 28 strokes) Pressure: 10,000 PSI (690 Bar) • Designed to transfer gear oils in and out of gear boxes, transfer cases and differentials • • • • Multiple Loading Cartridge PartNo. 305219 Suction Bulk Description With Steel Extension, Flexible Hose and Coupler Lip seal provides maximum suction Powder coated, textured steel barrel for firm grip No priming required Suitable for use with non-corrosive liquids Cartridge Capacity Bulk Capacity Thread PartNo. 450g 650cm 3 1/8” BSPT 305227 Description With 300mm (12”) Flexible Vinyl Hose Push Type Mini Grease Gun Hydraulic Couplers - 4 Jaw (General and Marine) For Hand Operated Grease Guns Only • Acrylic barrel withstands temperature variations 450g • Heat treated, fully hardened spring steel jaws for longer service life. • See-through barrel provides a clear view of grease volume General • Fitted with universal connector that adapts to most grease fittings • Handy disposable grease gun ideal for DIY use PartNo. Capacity • Incorporates a spring loaded ball check mechanism which helps retain pressure. • 4 Jaw allows greater working angle. Marine Capacity PartNo. 305225 With Ball Bearing Grease (NLG1-Grade 2) Description General 56g(2oz) 305226 With Calcium Complex Water Repellent Grease Marine 56g(2oz) Description Thread Pressure 305231 4 Jaw Hydraulic Coupler 1/8” BSPT 6,000 PSI (423 Bar) 305232 4 Jaw Hydraulic Coupler HD 1/8” BSPT 10,000 PSI (690 Bar) BSC Motion Technology 705 Lubrication TOOLS TOLEDO GREASE GUNS AND ACCESSORIES TOLEDO TOOLS, ACCESSORIES & OIL CANS Heavy Duty Flexible Grease Hoses Part No. 305381 Oil Drain Pan (6.6 litres) Acc DIN 1283 For Hand Operated Grease Guns Only • Superior construction - inner tubing is polyamide with polyurethane sheathing, reinforced diagonally in highly tear resistant polyester • Suitable for use with fuel oils, mineral oils, synthetic, antifreeze, etc • Heavy duty zinc plated end connections hydraulically crimped to the hose • Resistant to most chemicals, solvents and even hot oil • Rolled threads for extra strength Diameters: Inner-4.1mm (0.16”) Outer-10.8mm (0.425”) • Made of durable high density polyethylene with UV stabilizer • Dimensions: 35.5cm (dia.) x 10cm (depth) Pressures: Working pressure 5,800 PSI (400 Bar) Burst pressure 13,775 PSI (950 Bar) PartNo. Description Part No. 305248 Drum Lid Opening Wrench (Non Sparking) Length End to End 305234 Heavy Duty Grease Hose 300mm (12”) 305235 Heavy Duty Grease Hose 450mm (18”) 305236 Heavy Duty Grease Hose 500mm (20”) Grease Injector Needles • Manufactured from cast aluminium (LM25) • Designed to fit into most 2” and 3/4” drum plugs For Hand Operated Grease Guns Only Stainless Steel - Needle Length 38mm (11/2”) • Wrench is hardened and tempered for increased strength • Compact design for easy storage Drum Dollies • Lubricates in very tight spaces such as universal joints and sealed bearings • With standard grease fitting (without ball check) and protective plastic holder PartNo. Description • Extra heavy-duty design, wide steel in premium powder coated finish • H.D.Steel construction, phenolic casters on p/n 305383 • H.D.Steel construction, steel cross brace, cast iron casters on p/n 305265 Needle Thickness 305237 Grease Injector Needle 18 gauge 305238 Grease Injector Needle 21 gauge Part No. 305230 Bearing Packer • For use with grease guns, the design incorporates grease nipple at one end which easily adapts to the grease gun coupler 305265 • For bearings in cars, boats, trailers, 4WD’s etc. • Rugged bearings in cars, boats, trailers, 4WD’s etc. • May be used for regular greasing applications as well or in conjunction with a flexible hose 305383 PartNo. Warning: Always use recommended grade of grease. Some grades of grease cannot handle temperatures of wheel bearing applications. Do not use compressed air for cleaning the bearing prior to use with the bearing packer. This is unsafe and could damage the race. 706 BSC Motion Technology Description Capacity 305383 60 Litre Drum Dolly Holds drums of diameter 380mm (15”) 305265 205 Litre Drum Dolly Holds drums of diameter 584mm (23”) Lubrication TOOLS TOLEDO TOOLS, ACCESSORIES AND OIL CANS • Seamless and made from heavy gauge tin coated sheet with a powder coated finish • Deluxe brass suction pumps with two ball valves for large volume delivery per stroke • The suction valve at the bottom of the pump has no spring to prevent sticking valve due to resinous oil • Available with rigid shaft or combination flexible and rigid shaft PartNo. Description Capacity Rigid Spout Size Flexi Spout Size 125mm (5”) 150mm (6”) 305258 Lever Type, Rigid and Flexible Spout 300ml/10 oz 305259 Lever Type, Rigid and Flexible Spout 500ml/16 oz/1 Pint 305260 Lever Type, Rigid and Flexible Spout 700ml/23 oz 150mm (6”) 175mm (7”) 175mm (7”) 200mm (8”) TOLEDO PUMPS Part No. 305251 Rotary Drum Pump Part No. 305252 Lever Action Drum Pump • Suitable for use with oil based fluids, heating oils, motor oils, heavy and light oils • Specifically designed for heavy duty applications • Fits 50 litre to 205 litre drums • With a curved metal spout and telescopic suction tube, 1 1/2” and 2” bung adaptor. • Not recommended for use with water based fluids, solvents, acids and anti-freeze Output: 300ml (10 oz) per stroke • Suitable for transfer of diesel and non-corrosive petroleum based fluids of light to medium viscosity • Sturdy cast iron pump housing with two heavy duty cast iron vanes for better draw and smoother delivery • Hi Nitrile rubber seals • With telescopic Suction Tube. • Fits 50 litre to 205 litre drums Dual Directional Operation: Pumps in either direction by reverse turning the handle Output: 5 Litres per 20 turns (Note: as measured with diesel) “Ezee Flo” Pumps Description Drum Capacity Pump Length Rigid Steel Spout 20 litres 325mm 305255 Rigid & Flexible Hose & Spout 20 litres 325mm The Rieke adaptor conveniently screws on the plastic pull out Rieke spout BSC Motion Technology 305255 PartNo. 305254 305254 • Suitable for transferring engine oils, gear oils, diesel, 100% antifreeze and light fuels • A versatile hand lift pump engineered for use on 20 litre containers with Rieke or regular openings • Heavy duty steel suction tube with the pump head made from high density polyethylene • Interchangeable Bung Adaptors: The standard bung can be slid over the pump, when using on containers with external threading. Alternatively when using the pump on containers with plastic pull out Rieke spout, the other bung adaptor for Rieke spout can be used • Pump length can be extended by 19mm (3/4”) for use on high depth containers by conveniently sliding on a special plastic extension at the suction end. This makes the pump suitable for larger drum sizes • Designed for use on 20 litre containers. Available with rigid steel spout or with 1220mm (48”)discharge hose fitted with curved metal spout at discharge end • Not recommended for use with water based and other corrosive materials • Pump head has provision for draining back excess oil into the container when using the pump with standard bung adaptor Output: 1 litre (1 quart) per 15 strokes 707 Lubrication TOOLS TOLEDO GREASE NIPPLES • Made from – EN-1A steel with yellow zinc coating and 303 Stainless steel • Manufactured to the most stringent quality standards – QS9000 approved manufacturing • Nipple profile and dimensions are accurately controlled and conform to the SAE, DIN, BS, JIS and IS standards • Nipples with ball check use heat treated springs for increased life • Stainless steel nipples have stainless steel ball • Grease nipples are heat treated to SAE J534 specification Description Hex Size Steel Part No. Qty Steel Part No. Qty Stainless Steel Part No. Qty 305375 305376 10 10 305377 10 1/4” – 28 SAE-LT Taper Thread 5/16” 3/8” 3/8” 3/8” 305319* 305320* 305321* 305322* 10 5 5 5 305268 305269 305270 305271 20 20 20 20 7/16” 7/16” 7/16” 305323* 305324* 305325* 5 5 4 305272 305273 305274 20 20 20 0.60” 0.60” 0.60” 305326* 305327 305328 2 2 2 305275 305276 305277 20 20 20 5/16” 7/16” 7/16” 305329* 305330* 305331* 10 6 6 305278 305279 305280 20 20 20 7mm 9mm 11mm 305332 305333 305334 8 5 3 305281 305282 305283 20 20 20 7/16” 7/16” 7/16” 7/16” 7/16” 305335* 305336 305337 305338* 305339* 7 5 5 4 4 305284 305285 305286 305287 305288 20 20 20 20 20 305370 305371 305372 305373 305374 10 10 10 10 10 7mm 9mm 9mm 305340* 305341* 305342* 10 5 5 305289 305290 305291 20 20 20 305361 305362 305363 10 10 10 9mm 9mm 9mm 305343* 305344 305345* 8 5 5 305292 305293 305294 20 20 20 305364 305365 305366 10 10 10 11mm 11mm 11mm 305346* 305347* 305348* 6 5 5 305295 305296 305297 20 20 20 305367 305368 305369 10 10 10 Dia 5/16” Dia 3/8” Dia 11/32” 305349* 305350 305351* 10 8 10 305298 305299 305313 20 20 20 305352* 305353 3 3 305314 305315 20 20 305354 305355 305356 3 1 2 305316 305317 305318 20 20 20 Short Straight Short– 45° Short– 65° Short– 90° R 1/8” x 19 BSPT Taper Thread Straight 45° 90° R 1/4” x 19 BSPT Taper Thread Straight 45° 90° UNF Parallel Thread Straight Straight Straight 1/4” -28 5/6” – 24 3/8” - 24 BSF Parallel Thread Straight Straight Straight 1/4” – 26 5/16” – 22 3/8” – 20 1/8” – 27 Pipe Threads PTF – Special Short Short Straight Short – 30° Short – 45° Short – 65° Short – 90° 6.0mm x 1.0mm Taper Thread Short Straight Short – 45° Short 90° 8.0mm x 1.0mm Taper Thread Short Straight Short– 45° Short– 90° 10.0mm x 1.0mm Taper Thread Short Straight Short – 45° Short – 90° Drive Fittings For For For 3/16” Drill 5/16” Drill 1/4” Drill Button Head Grease Fittings Parallel Thread 1/4” x 19 BSP 1/8” x 28 BSP 0.6” 0.6” Button Head Grease Fittings Taper Thread 1/8”-27 PTF SAE spl Short 3/8”-18 NPTF 1/4”-18 NPTF 708 5/8” 3/4” 5/8” BSC Motion Technology Lubrication TOOLS TOLEDO GREASE NIPPLES Part No. 305212 Assorted SAE Grease Nipples • Handy pack of1/4”SAE steel nipples. Qty 4 pcs Description Straight Nipples Part No. 305213 Assorted Metric Grease Nipples • Handy pack of 6mm steel nipples. Quantity Description 4 pcs Straight Nipples 2 pcs 45 Angle Nippies 2 pcs 45o Angle Nippies 2 pcs 90o Angle Nippies 2 pcs 90o Angle Nippies o Part No. 305266 Assorted SAE Grease Nipple Set • Made from EN-1A steel (plated yellow zinc), heat treated • Manufactured to QS9000 Quality Standards Qty Description Part No. 305267 Assorted Metric Grease Nipple Set • Made from EN-1A steel (plated yellow zinc), heat treated • Manufactured to QS9000 Quality Standards Qty Description 30 pcs 1/8” 27 NPT Straight 30 pcs 6mm x 1 Straight 15 pcs 1/8” 27 NPT 45° Angle 20 pcs 6mm x 90° Angle 15 pcs 1/8” 27 NPT 90° Angle 20 pcs 8mm x 1 Straight 20 pcs 1/4” 28 SAE LT Straight 20 pcs 8mm x 90° Angle 15 pcs 1/4” 28 SAE LT 45° Angle 20 pcs 10mm x 1 Straight 15 pcs 1/4” 28 SAE LT 90° Angle 10 pcs 10mm x 90° Angle Part No. 305378 Stainless Steel Metric Grease Nipple Set • Made from 303 Stainless steel with stainless steel ball. • Manufactured to QS9000 Quality Standards Qty Description 30 pcs 6mm x 1 Straight 15 pcs 6mm x 45° Angle 15 pcs 6mm x 90° Angle 20 pcs 8mm x 1 Straight 15 pcs 8mm x 45° Angle 15 pcs 8mm x 90° Angle BSC Motion Technology 709 Cable Ties TOOLS CABLE TIE RETAIL PACKS • Nylon cable ties are manufactured from virgin nylon 6/6 and are UL94V-2 flammable rated. • Black cable ties have been U.V. stabilised to resist material breakdown and increase service life. NATURAL CABLE TIES Width Length mm mm Retail Packs Part No. Bulk Quantities Qty Part No. Qty CTB603NT 500 3 60 CT603NTCD 100 3 100 CT103NTCD 100 3 100 CTB103NT 500 CTW103NT 1000 4 150 CT154NTCD 100 CTB154NT 500 4 200 CT204NTCD 100 CTB204NT 500 4 250 CT254NTCD 100 4 300 CT304NTCD 100 5 200 CT205NTCD 100 CTB205NT 500 5 250 CT255NTCD 100 CTB255NT 500 5 300 CT305NTCD 100 CTB305NT 500 5 400 CT405NTCD 25 CTB1009NT 250 5 450 CT455NTCD 25 8 200 CT208NTCD 25 8 250 CT258NTCD 25 8 300 CT308NTCD 25 8 350 CT358NTCD 25 8 400 CT408NTCD 25 9 550 CT559NTCD 25 25 9 750 CT759NTCD 9 1000 CT1009NTCD 25 12 650 CT6512NTCD 25 BLACK CABLE TIES (U.V STABILISED) Width mm 710 BSC Motion Technology Length mm Retail Packs Qty Part No. Qty CT603BKCD 100 CTB603BK 500 100 CT103BKCD 100 CTB103BK 500 150 CT154BKCD 100 CTB154BK 500 4 200 CT204BKCD 100 CTB204BK 500 4 250 CT254BKCD 100 4 300 CT304BKCD 100 5 200 CT205BKCD 100 CTB205BK 500 5 250 CT255BKCD 100 CTB255BK 500 5 300 CT305BKCD 100 CTB305BK 500 5 400 CT405BKCD 25 CTB405BK 500 5 400 CT405BKCD-100 100 5 450 CT455BKCD 25 CTB455BK 500 5 450 CT455BKCD-100 100 8 200 CT208BKCD 25 8 250 CT258BKCD 25 8 300 CT308BKCD 25 8 350 CT358BKCD 25 8 400 CT408BKCD 25 CTB408BK 500 8 400 CT408BKCD-100 100 9 550 CT559BKCD 25 9 750 CT759BKCD 25 9 1000 CT1009BKCD 25 12 650 CT6512BKCD 25 3 60 3 4 Part No. Bulk Quantities Cable Ties TOOLS CABLE TIE PACKS Part No: CTP03 Part No: CTP07 Part No: CTP08 Width Total Length Qty Pack Qty Width Total Length Qty Pack Qty Width 3mm 100mm 3mm 100mm 300 3mm 100mm 300 3mm 150mm 200 3mm 200mm 200 100 1000 Part No: CTP21 Part No: CTP23 Width 3mm 500 Total Length Qty Pack Qty 500 Part No: CTP24 Part No: CTP22 Total Length Qty Pack Qty Width Total Length Qty Pack Qty Width Total Length Qty Pack Qty 200mm 3mm 100mm 3mm 200mm 200 200 300 300 200 200 Width 3mm Total Length Qty Pack Qty 100mm 300 300 CABLE TIE COMBO PACK • Contains popular sizes of black (U.V. Stabilised) cable ties in one handy carry pack • 1000 cable ties in total Part No: CTCP10 Width Length Part No Total Pack Qty 3mm 100mm CT103BKCD 4mm 150mm CT154BKCD 2 x Packs of 100 2 x Packs of 100 5mm 200mm CT205BKCD 4 x Packs of 100 5mm 300mm CT305BKCD 2 x Packs of 100 BSC Motion Technology 711 Pliers TOOLS KNIPEX KNIPEX Combination Pliers • with gripping zones for flat and round material, suitable for versatile use • with cutting edges for soft and hard wire • long cutting edges for thicker cables • cutting edges additionally induction hardened, cutting edge hardness approx. 60 HRC • special tool steel, oil-hardened and tempered Cutting Capacities Part No Length Head Handles 9.0ømm 2 03 01 140 140mm polished plastic coated 2.8 ømm 1.8 ømm 10.0mm 03 01 160 160mm polished plastic coated 3.1 ømm 2.0 ømm 10.0ømm 2 16.0mm 03 01 180 180mm polished plastic coated 3.4 ømm 2.2 ømm 12.0ømm 2 16.0mm 03 01 200 200mm polished plastic coated 3.8 ømm 2.5 ømm 13.0ømm 2 16.0mm 03 01 250 250mm polished plastic coated 3.8 ømm 2.5 ømm 15.0ømm 2 25.0mm KNIPEX Snipe Nose Side Cutting Pliers, Cutting edges for wire and cable Gripping zone for flat material Gripping zone for round material Stork Beak Pliers • • • • Part No Length Style Head Handles 26 11 200 200mm Straight Tips polished plastic coated high loadable, elastic precision points half-round, long jaws serrated gripping surfaces with cutting edges for medium hard wire max. dia. 3.2 mm and hard wire max. dia. 2.2 mm • cutting edges additionally induction hardened, cutting edge hardness approx. 61 HRC • Vanadium steel, oil-hardened and tempered REQUIRES KNIPEX ‘Cobolt’, Compact Bolt Cutters (Lever Action Centre Cutters) • with precision blades for soft, hard and piano wire • cuts material like bolts, nails, rivets, etc. up to 5.2mm dia. • exceptional cutting performance with minimum effort because of new lever action design • cutting edges additionally induction hardened, cutting edge hardness approx. 64 HRC • Forged, Chrome Vanadium electric steel, oil-hardened and tempered Cutting Capacities Part No 71 01 200 Length 200mm Head Handles polished plastic coated 6.0 ømm 5.2 ømm 4.0 ømm 61% LESS EFFORT 3.6 ømm REQUIRES KNIPEX High Leverage Diagonal Cutters 21% LESS EFFORT • • • • Cutting Capacities Part No Length Head Handles 74 01 140 140mm polished plastic coated 3.1 ømm 2.0 ømm 1.5ømm 74 01 160 160mm polished plastic coated 3.4 ømm 2.5 ømm 2.0ømm 74 01 180 180mm polished plastic coated 3.8 ømm 2.7 ømm 2.2ømm 74 01 200 200mm polished plastic coated 4.2 ømm 3.0 ømm 2.5ømm 74 01 250 250mm polished plastic coated 4.6 ømm 3.5 ømm 3.0ømm 712 BSC Motion Technology with forged-on axle for heaviest duty suitable for all types of wire including piano wire high cutting performance with minimum effort. precision cutting edes additionally induction hardened, cutting edge hardness approx. 64 HRC • Chrome Vanadium electric steel, oil-hardened and tempered Pliers TOOLS KNIPEX KNIPEX ‘Cobra’, the HiTech Water Pump Plier • fast and comfortable handling directly on the workpiece • One adjustment: ensures optimum adjustment to differently sized workpieces and user-friendly handle position; • box-joint design: high stability because of double guide • self-locking on pipes and nuts: no slipping on the workpiece and low handforce required • gripping surfaces with special hardened teeth, teeth hardness approx. 61 HRC: low wear and secure gripping • one-hand adjustment guard, prevents operators’ fingers being pinched • Chrome Vanadium electric steel, oil-hardened and tempered 87 01 150 87 01 250 87 01 400 Capacities For pipes For nuts Part No Length Head Handles 87 01 150 150mm polished plastic coated 1 1/4” 30mm 87 01 180 180mm polished plastic coated 1 1/4” 30mm 87 01 250 250mm polished plastic coated 1 1/2” 36mm 87 01 300 300mm polished plastic coated 2 46mm 87 01 400 400mm polished plastic coated 3 1/2” 95mm 87 01 560 560mm polished plastic coated 4 1/2” 120mm Fast and firm adjustment directly on the workpiece 87 01 150: Is small enough to fit into a shirt breast pocket. KNIPEX Internal Circlip Pliers (bore holes) Part No Length 44 11 JO Style Head Handles Size of bore 140mm polished plastic coated 8-13 ømm 44 11 J1 140mm polished plastic coated 12-25 ømm 44 11 J2 180mm polished plastic coated 19-60 ømm 44 11 J3 225mm polished plastic coated 40-100 ømm 44 11 J4 320mm polished plastic coated 85-140 ømm Part No Length Head Handles Size of bore 44 21 JO1 130mm polished plastic coated 8-13 ømm 44 21 J11 130mm polished plastic coated 12-25 ømm 44 21 J21 170mm polished plastic coated 19-60 ømm 44 21 J31 215mm polished plastic coated 40-100 ømm 44 21 J41 300mm polished plastic coated 85-140 ømm Straight Style 90o Bend • • • • for fitting internal circlips in bore holes from 8 - 400 mm dia. solid style, forged non-slip, solid tips Chrome Vanadium electric steel, oil-hardened and tempered BSC Motion Technology 713 Pliers TOOLS KNIPEX KNIPEX External Circlip Pliers (shafts) Part No Length 46 11 AO Style Head Handles Size of shaft 140mm polished plastic coated 3-10 ømm 46 11 A1 140mm polished plastic coated 10-25 ømm 46 11 A2 180mm polished plastic coated 19-60 ømm 46 11 A3 210mm polished plastic coated 40-100 ømm polished plastic coated 85-140 ømm Head Handles Size of bore • • • • for fitting external circlips on shafts from 3 - 400 mm dia. solid style, forged non-slip, solid tips Chrome Vanadium electric steel, oil-hardened and tempered Straight 46 11 A4 320mm Part No Length 46 21 AO1 125mm polished plastic coated 3-10 ømm 46 21 A11 125mm polished plastic coated 10-25 ømm 46 21 A21 170mm polished plastic coated 19-60 ømm 46 21 A31 200mm polished plastic coated 40-100 ømm polished plastic coated 85-140 ømm Style 90 o Bend 46 21 A41 300mm Special Retaining Ring Pliers (shafts) • for fitting horseshoe-shaped spring retaining rings and circlips without grip holes • for retaining rings with a minimum ring split gap of 3.6 mm • for shaft retaining devices • forged with opening spring • Chrome Vanadium steel, oil-hardened and tempered Part No Length 45 10 170 170mm 714 Style Head burnished Handles burnished BSC Motion Technology Pliers TOOLS KNIPEX KNIPEX TOOL SETS Part No: 00 19 56 KNIPEX Circlip Plier Set • tool roll equipped with four popular Circlip Pliers for internal and external circlips • with practical, adjustable quick-release fastener • transparent protective cap Circlip Plier Set Part No: 00 19 56 Part No Length Style Head Handles Bore/Shaft Size 44 11 J2 180mm Straight polished plastic coated 19-60 ømm polished plastic coated 19-60 ømm polished plastic coated 19-60 ømm polished plastic coated 19-60 ømm o 44 21 J21 170mm 90 Bend 46 11 A2 180mm Straight 46 21 A21 170mm 90 o Bend Part No: 00 19 57 CirclipPlier KNIPEX Precision CirclipSet Plier Set Part no: 0 19 56 • tool roll equipped with four popular Precision Circlip Pliers for internal and external circlips • Precision Circlip pliers have inserted tips of high density drawn spring wire. • Ten times longer service life. Precision Circlip Plier Set Part No: 00 19 57 KNIPEX Plier / Cutter Tool Set Part No: 0035 Part No Length Style Head Handles Bore/Shaft Size 48 11 J1 140mm Straight polished plastic coated 12-25 ømm 48 11 J2 180mm Straight polished plastic coated 19-60 ømm 49 11 A1 140mm Straight polished plastic coated 10-25 ømm 49 11 A2 180mm Straight polished plastic coated 19-60 ømm Part No: 002011S KNIPEX Assembly Pack • Tool roll containing four popular plier/cutter tools. • Premium quality and long service life. • Handy tool pack containing popular pliers. • Made in Germany. Plier Tool Roll Part No: 0035 Assembly Pack Part No: 002011S Part No Description Length Head 87 01 250 Cobra Water Pump Pliers 250mm polished plastic coated 87 02 250 26 11 200 Snipe Nose Cutting Pliers 200mm polished plastic coated 02 02 200 High Leverage Combination Plier 03 01 200 Combination Pliers 74 01 200 High Leverage Diagonal Pliers 200mm 200mm polished polished Handles plastic coated Part No 74 02 200 Description Length Cobra Water Pump Pliers Diagonal Cutters 250mm Head Handles polished plastic coated 200mm polished plastic coated 200mm polished plastic coated plastic coated BSC Motion Technology 715 Screwdrivers TOOLS WERA WERA KRAFTFORM® PLUS SERIES 300 SCREWDRIVER SET Part No: 05 105650 001 Slotted and Phillips Screws • Six piece screwdriver set for slotted and Phillips screws. • Each Kraftform® Plus 300 Series Screwdriver feature the ergonomically designed Kraftform® handle. • The Kraftform® handle shape is perfectly adapted to the palm and sits firmly in the hand. • Includes Lasertip® treated tip - prevents slipping out of the screw head. • Includes display carton and rack. • German quality. Type Head Size Shaft Length Lasertip® Qty 3mm 80mm 1 4mm 100mm 1 5.5mm 125mm 1 6.5mm 150mm 1 PH1 80mm 1 PH2 100mm 1 WERA KRAFTFORM® CHISELDRIVER SCREWDRIVER SET Part No: 05 018282 001 Slotted and Phillips Screws • Six piece chiseldriver screwdriver set for slotted and Phillips screws. Type • For fastening, chiselling and loosening seized screws. • With integrated impact cap and ‘pound-thru’ hexagonal blade. • Each Kraftform® Plus 900 Series Chiseldriver feature the ergonomically designed Kraftform® handle. Head Size Shaft Length Qty 3.5mm 80mm 1 4.5mm 90mm 1 5.5mm 1200mm 1 7mm 125mm 1 PH1 80mm 1 PH2 100mm 1 • The Kraftform® handle shape is perfectly adapted to the palm and sits firmly in the hand. • Includes display carton. • German quality. WERA KRAFTFORM® CLASSIC SCREWDRIVER SET Part No: 05 031280 001 Slotted and Phillips Screws • Six piece economical screwdriver set for slotted and Phillips screws. Type • Each Kraftform® Classic Screwdriver feature the ergonomically designed Kraftform® handle. • The Kraftform® handle shape is perfectly adapted to the palm and sits firmly in the hand. • Features Wera Black Point Tip, which reduces wear and extends the service life of screws and tools. Head Size Shaft Length Qty 3mm 80mm 1 4mm 100mm 1 5.5mm 125mm 1 6.5mm 150mm 1 PH1 80mm 1 PH2 100mm 1 Head Size Shaft Length Qty 3mm 80mm 1 4mm 100mm 1 5.5mm 125mm 1 6.5mm 150mm 1 PZ1 80mm 1 PZ2 100mm 1 • Includes display carton. • German quality. WERA KRAFTFORM® C Part No: 05 031281 001 Slotted and Pozidriv Screws • Six piece economical screwdriver set for slotted and Pozidriv screws. • Each Kraftform® Classic Screwdriver feature the ergonomically designed Kraftform® handle. • The Kraftform® handle shape is perfectly adapted to the palm and sits firmly in the hand. • Features Wera Black Point Tip, which reduces wear and extends the service life of screws and tools. • Includes display carton. • German quality. 716 BSC Motion Technology Type FOR TOUGH JO BS! Socket and Spanner Sets z z z z z z zz z z z z z z zz zz z zz z z z z z z Unique Patented Design Metrinch’s patented wall drive allows the wrench to grip a much larger wall surface of the bolt or nut. The 4-point grip design enables Metrinch sockets and spanners to ?t multiple sizes and damaged or rounded nuts. Traditional sockets and spanners only have a 2-point grip and depend on a precise fit at the bolt or nut’s corners. z zzzz z zz zz z zz zz zz z zz Get More Use Out of Fewer Tools Metrinch means fewer tools and easier selection as each tool can be used for both metric and inch, plus damaged nuts and bolts. This eliminates switching back and forth from imperial to metric, one tool set is all you need. Fewer tools also means less cost and a lighter toolbox. z zz z z z Metrinch means fewer tools z z z z z TOOLS z z z z z z zz zz zz zz z zzz zz zzzz Non Slip Hold No slipping means greater safety. No more cut hands, banged up knuckles and elbows due to wrench slippage. Lifetime Guarantee All Metrinch tools are forged from high grade chrome vanadium steel for lifetime use. This provides improved safety, particularly in conditions involving extreme stress. Metrinch tools are chrome plated or polished to provide the most effective protection against rust. Spare Parts Spare parts are available for Metrinch kits so tools are easily replaced if lost. Patented Wall Drive Profile Unique 6 Wall Drive System Certi?ed Professional Quality All Metrinch tools meet DIN, BS and US Federal standards for torque and hardness. Metrinch tools come complete with a lifetime guarantee. More Torque, Less Wear By exerting pressure through the walls, Metrinch grips more securely than conventional sockets. Since torque pressure is spread more evenly through the wall, there is less distortion in both the tool and the fastener. The Metrinch 6 wall drive system means that one tool set is all you need to service your equipment, whether it’s made in Germany, the USA or Australia. The patented Metrinch wall drive profile works from the flats on a nut or bolt, not the corners. METRINCH IMPACT SOCKET SETS Part No. MET-2400 15 Piece Standard Impact Socket Set 1/2” Drive Part No. MET-2450 15 Piece Deep Wall Impact Socket Set 1/2” Drive 15=42 15=42 This 15 piece set equals a 42 piece conventional set Fits Metric mm 11 12 13 14 15 16 17 18 Cont. SAE/AF Inch 7/ 16 15/ 32 1/ 2 9/ 16 19/ 32 5/ 8 11/ 16 23/ 32 1/2” Drive Socket Fits Metric mm Fits Cont. SAE/AF Inch 1/2” Drive Socket Metric mm 19 3/ 20 25/ 32 12 21 13 24 13/ 16 7/ 8 29/ 32 15/ 16 16 25 1 17 22 23 4 This 15 piece set equals a 42 piece conventional set 11 14 15 18 Cont. SAE/AF Inch 7/ 16 15/ 32 1/ 2 9/ 16 19/ 32 5/ 8 11/ 16 23/ 32 Fits 1/2” Drive Deep Socket Metric mm Cont. SAE/AF Inch 19 3/ 20 25/ 4 24 32 13/ 16 7/ 8 29/ 32 15/ 16 25 1 21 22 23 BSC Motion Technology 1/2” Drive Deep Socket 717 Socket and Spanner Sets TOOLS METRINCH SPANNER SETS Part No: MET-0110 Part No. MET-0110 10 Piece Spanner Set 10=28 Contents Metric mm This 10 piece set equals a 28 piece conventional set SAE/AF Inch Part No: MET-0125 Part No. MET-0125 14 Piece Spanner Set 14=45 Contents This 14 piece set equals a 45 piece conventional set Metric mm SAE/AF Inch 8 8 5/ 16 9 11/ 32 10 3/ 2 11 7/ 10 3/ 11 7/ 12 15/ 13 1/ 16 32 8 16 12 15/ 32 32 13 1/ 2 8 14 9/ 16 15 19/ 32 8 14 9/ 15 19/ 16 5/ 16 16 17 11/ 18 23/ 32 16 5/ 19 3/ 4 17 11/ 18 23/ 32 19 3/ 4 20 25/ 32 21 13/ 16 16 22 7/ 8 23 29/ 32 METRINCH SOCKET SETS Part No. MET-0420 17 Piece Standard Socket Set 1/2” Drive Part No. MET-0210 24 Piece Standard Socket Set 1/4” Drive 17=58 24=50 This 17 piece set equals a 58 piece conventional set Fits Metric mm 10 11 12 13 14 15 16 17 18 19 718 Cont. SAE/AF Inch 3/ 8 7/ 16 15/ 32 1/ 2 9/ 16 19/ 32 5/ 8 11/ 16 23/ 32 3/ 4 1/2” Drive Socket Fits Metric mm 20 21 Cont. SAE/AF Inch 25/ 24 32 13/ 16 7/ 8 15/ 16 25 1 26 27 11/16 13/ 32 29 30 15/ 32 13/16 31 32 17/ 32 11/4 22 BSC Motion Technology 1/2” Drive Socket This 24 piece set equals a 50 piece conventional set Fits Contents Metric SAE/AF 1/4” Drive 1/4” Drive mm Inch Socket Deep Socket 4 5 6 7 8 9 10 11 12 13 5/ 32 3/ 16 1/ 4 9/ 32 5/ 16 11/ 32 3/ 8 7/ 16 15/ 32 1/ 2 Accessories: •Quick Release Reversible Ratchet • 150mm (6”) Extension Bar • Fingertip Ratchet • Universal Joint Socket and Spanner Sets TOOLS METRINCH SOCKET AND SPANNER SETS Part No. MET-0450 30 Piece Socket and Spanner Set 1/2” Drive 30=88 This 30 piece set equals a 88 piece conventional set Accessories : • 125mm (5”) Extension Wobble Bar • Disc Type Quick Release Ratchet Handle Fits • 21mm & 13/16” Spark Plug Socket • Flexible Handle • Universal Joint Contents Fits 1/2” Metric SAE/AF Drive Spanner mm Inch Socket 3/ 8 7/ 16 15/ 32 1/ 2 9/ 16 19/ 32 5/ 8 11/ 16 23/ 32 3/ 4 10 11 12 13 14 15 16 17 18 19 Part No. MET-0650 50 Piece Socket and Spanner Set 1/4”, 3/8” & 1/2” Drive 50=124 This 50 piece set equals a 124 piece conventional set 24 32 13/ 16 7/ 8 29/ 32 15/ 16 25 1 26 27 11/16 13/32 28 11/8 29 30 15/32 13/16 31 32 17/32 11/4 2” Drive Accessories: •75mm (3”) Wobble Extension Bar • 125mm (5”) Extension Bar • 250mm (10”) Extension Bar • Sliding T-Piece • Flexible Handle Ratchet •Quick Release Ratchet – 32 Teeth Fits 5 6 7 8 9 10 11 12 13 14 16 17 19 20 21 22 24 26 27 29 30 • Square Driver - Plastic Handle 22 23 25/ • 125mm (5”) Extension Bar • Quick Release Ratchet – 25 Teeth • 75mm (3”) Extension Bar • Universal Joint • 16mm & 5/8” Spark Plug Socket • 21mm & 13/16” Spark Plug Socket • 38mm & 1/2” Wobble Ex. Bar Metric mm • 3/8” F & 1/4” M Adaptor 20 21 3/8” Drive Accessories: 1/ 1/4” Drive Accessories: Contents 1/2” Metric SAE/AF Drive Spanner mm Inch Socket 31 32 Contents SAE/AF Inch 1/4” Drive Socket 3/8” Drive Socket 1/2” Drive Socket 3/8” Drive Deep Socket Spanner 3/ 16 1/ 4 9/ 32 5/ 16 11/ 32 3/ 8 7/ 16 15/ 32 1/ 2 9/ 16 5/ 8 11/ 16 3/ 4 25/ 32 13/ 16 7/ 8 15/ 16 11/16 13/ 32 15/ 32 13/16 17/ 32 11/4 BSC Motion Technology 719 TOOLS 720 BSC Motion Technology