CH A P T E R
4
Building the Display Shelf Assembly
Revised: September 16, 2009, OL-14521-01
Parts List
Display Shelf, Type 1
Key
Part Description
Part Number
Qty
Ctn
1
Display shelf section: left
700-23600-xx
1
58
2
Display shelf section: center
700-23599-xx
1
58
3
Display shelf section: right
700-23598-xx
1
58
4
Not used
5
Left accessory cabinet attachment bracket
700-23336-xx
1
19
6
Right accessory cabinet attachment bracket
700-23337-xx
1
19
7
Not used
8
Connecting plates
700-23345-xx
2
13
9
Speaker board brackets
6
46
10
Splines
No part number
2
58
11
Draw bolts
51-4579-xx
6
58
12
and
13
M8 x 20 mm screws
48-2273-01
Notes
Included with projector screen kit.
1
Cisco TelePresence System 3200
OL-14521-01
4-1
Chapter 4
Building the Display Shelf Assembly
Parts List
Accessory Cabinet
1
Accessory Cabinet, Right
700-29441-01
Kit # 69-1837-xx
1
47
2
Accessory Cabinet, Left
700-29442-01
Kit #69-1838-xx
1
48
3
Assembly Screen Supports
No part number
2
4
M8 x 30 mm screws
69-1706-xx
14
Located inside of assembly cabinet.
These brackets are only required if
you use a Type 1 projector screen,
part number 800-28681-01. If your
installation uses the projector
screen with a product ID of
CTS3K-SCREEN and a part
number of 74-5416-01, do not
install these brackets.
1
Caution
The shelf segments are unstable during assembly. Use caution, and support all structures as required.
Caution
Some system components have metal and plastic edges with hard angles. These edges are exposed until
you complete system assembly. Use caution when you move around the system during assembly to avoid
contact with any exposed system edges.
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Caution
Note
In order to prevent scratching the Display shelves, you should avoid putting any tools on the shelf
surfaces.
The directions left and right refer to the assembly as you face the Plasma displays.
Cisco TelePresence System 3200
4-2
OL-14521-01
Chapter 4
Building the Display Shelf Assembly
Parts List
Step 1
Figure 4-1
Attach the Display shelf hardware.
Display shelf hardware
14
14
8
8
12
9
5
12
12
9
6
3
10 11
205467
1
Note
The Right Accessory Cabinet attachment bracket (marked “6” in the illustration), has a central
rectangular hole that differentiates it from the Left Accessory Cabinet attachment bracket.
Note
This illustration describes the hardware used to attach the three Display shelves and the
hardware used to attach additional assemblies in Chapter 8, “Assembling the Remaining
Cisco TelePresence Elements.” The Display shelves should be attached individually to the
Display structures, as illustrated in Figure 4-2, Figure 4-3, and Figure 4-4.
Cisco TelePresence System 3200
OL-14521-01
4-3
Chapter 4
Building the Display Shelf Assembly
Parts List
Step 2
Figure 4-2
Attach the left Display shelf.
Left Display shelf
13
13
201148
1
Cisco TelePresence System 3200
4-4
OL-14521-01
Chapter 4
Building the Display Shelf Assembly
Parts List
Step 3
Figure 4-3
Attach the center Display shelf
Center Display shelf
13
13
Note
201149
2
Refer to Figure 4-1 to see the hardware used to attach the center Display shelf to the left Display
shelf.
Cisco TelePresence System 3200
OL-14521-01
4-5
Chapter 4
Building the Display Shelf Assembly
Parts List
Step 4
Figure 4-4
Attach the right Display shelf.
Right Display shelf
13
Note
13
201150
3
Refer to Figure 4-1 to see the hardware used to attach the right Display shelf to the center
Display shelf.
Cisco TelePresence System 3200
4-6
OL-14521-01
Chapter 4
Building the Display Shelf Assembly
Parts List
Step 5
Attach the screen supports to the accessory cabinets and position, but do not attach, the cabinets to the
left and right attachment brackets
These screen supports are only required if you use a Type 1 projector screen, part number 800-28681-01.
If your installation uses the projector screen with a product ID of CTS3K-SCREEN and a part number
of 74-5416-01, do not install these brackets.
Figure 4-5
Accessory Cabinet
12
2
1
3
4
4
3
204159
12
Note
One wall of the left Accessory cabinet was removed from this illustration for clarity.
Note
Before you attach the Accessory cabinets to the brackets, use them as supports while assembling
the table segments in Chapter 6, “Building the First Row Table Assembly.”
Cisco TelePresence System 3200
OL-14521-01
4-7
Chapter 4
Building the Display Shelf Assembly
Parts List
Cisco TelePresence System 3200
4-8
OL-14521-01