EF300 SERIES
SIZE B RECESSED
INSTALLATION INSTRUCTIONS
Warnings:
* Risk of fire or electric shock.
* Disconnect all power before installing or servicing.
* Installation Instructions for qualified electricians only.
* Install per National Electrical Code and local regulations.
* Read Installation Instructions completely before installation.
* Failure to follow Installation Instructions may void warranties.
®
C
US
THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
PAGE 1 OF 2
Extruded Aluminum
Housing
Suspension
Tie Down
Bracket
Fastening Screw
Ceiling
Material
Housing
Fastener Strap
Hang 1/4-20 or
Wire CableTie Down
LED Driver
LED Module
Reflector
Extruded Aluminum
Mud-in Compound Flange
Mudding
Compound
FIGURE 1
Extruded Snap-in
Acrylic Lens
ASSEMBLY NOTE: The EF300 Recessed Series primarily consist of 4 major components A,
B, C, and D. See Fig. 2 & Fig. 3. This system is designed for ease of installation. IT IS IMPORTANT TO READ INSTRUCTION SHEET COMPLETELY BEFORE INSTALLATION.
Trimless
A Recessed
Hanger Assembly
A - SUSPENDED HANGER ASSEMBLY:
1. SUSPEND HANGER ASSEMBLY IN PLACE using 1/4-20 all thread or wire cable tie downs.
Suspension tie down bracket locations vary. Typically 6” from each end on each side of
housing.
2. When SETTING HANGER ASSEMBLY be sure the top of the mud-in compound flange is flush
to the bottom of the finished ceiling height. See Fig 1
B - EF300 HOUSING INSERT:
1. SLIDE FIXTURE HOUSING INTO HANGER ASSEMBLY and fasten into place using hardware
provided. Pre-set mounting locations match housing fastener strap. See Fig 1.
2. Fasten mud-in compound flange to ceiling. PRIOR TO FASTENING MUD-IN COMPOUND
FLANGE, place lens into housing to ensure proper housing to lens width. MUST TEST LENS FIT
BEFORE MUD-IN. Secure using drywall screws (provided by others). Screw through the flange
and into the drywall. REMOVE LENS, tape and mud-in to trim edge spreading mudding compound a minimum of 6” onto finished ceiling. See Fig 1.
Aluminum
B Extruded
Fixture Housing
C - OPTICAL ASSEMBLY AND POWER SUPPLY:
Assembly
C Optical
& Power Supply
D - EXTRUDED ACRYLIC LENS:
Acrylic
D Extruded
Snap-in Lens
1. INSERT OPTICAL & POWER SUPPLY ASSEMBLY by inserting up into the housing cavity.
There is a tension clip on each side of driver housing, squeeze/compress and push up past
inner housing tabs and release. This will lock assembly into place See Fig 3.
1. SNAP-IN LENS once all housing and inner components have been set in place, wiring complete
and mud-in finished. Gently push lens into housing until formed tabs snap-in to place.
FIGURE 2
©2015 LF ILLUMINATION LLC
HEADQUARTERS
Telephone: 818-885-1335
We reserve the right to change or
9200 Deering Avenue
Toll Free: 855-885-1335
withdraw specifications without prior notice.
Chatsworth CA 91311
Fax: 818-576-1335
www.lfillumination.com
REV. 0040315
EF300 SERIES
SIZE B RECESSED
INSTALLATION INSTRUCTIONS
Warnings:
* Risk of fire or electric shock.
* Disconnect all power before installing or servicing.
* Installation Instructions for qualified electricians only.
* Install per National Electrical Code and local regulations.
* Read Installation Instructions completely before installation.
* Failure to follow Installation Instructions may void warranties.
®
C
US
THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
PAGE 2 OF 2
EXPLODED ASSEMBLY VIEW:
Housing Fastener
Strap
The EF300 Recessed Series primarily consist of 4 major
components A, B, C, and D. See Fig. 2 & Fig. 3. This system
is designed for ease of installation.
FOR ASSEMBLY SEQUENCE SEE PAGE ONE.
Wire Cable
Tie Down
Trimless
A Recessed
Hanger Assembly
Aluminum
B Extruded
Fixture Housing
Optical
Fastening
Tension Clips
Assembly
C Optical
& Power Supply
Acrylic
D Extruded
Snap-in Lens
FIGURE 3
NOTE: ALL WORK MUST BE
DONE WITH CIRCUIT OFF AND
COMPONENTS SHOULD NOT BE
INSTALLED WHEN FIXTURE IS
ENERGIZED.
CONNECTING FOR CONTINUOUS RUNS:
Loosen and extend internal connecting joiners half way and lock in position.
Slide corresponding channel onto exposed joiner and lock into place.
See Fig. 4 steps 1 & 2.
Channel
Locking
Joiners
End Cap
A
FIGURE 4
Snap in lens
B
the alignment/locking
1 Extend
joiners mid way
corresponding channels
2 Slide
together and fasten
©2015 LF ILLUMINATION LLC
HEADQUARTERS
Telephone: 818-885-1335
We reserve the right to change or
9200 Deering Avenue
Toll Free: 855-885-1335
withdraw specifications without prior notice.
Chatsworth CA 91311
Fax: 818-576-1335
www.lfillumination.com
rev: 040315