Doors
Front Door Sash Inner Trim
Replacement (cont'd)
USA-produced models
Fastener Location
t > : Clip, 1
Front Door Sash Outer Trim
Replacement NOTE:
• Take care not to scratch the door.
• 4-door is shown; 2-door is similar.
1. Remove the door outer molding (see page 20-36).
2. Pull up the door sash outer trim (A) to release the
hooks (B) from the door, and release the trim from
between the door glass outer weatherstrip (C) and the
door, then remove the trim. Take care not to damage
the door glass outer weatherstrip.
F
4. Install the trim in the reverse order of removal, and
note these items:
• If the clip is damaged or stress-whitened, replace it
with a new one.
• Push the clip, the hooks, and the hook strips into
place securely.
3. Install the trim in the reverse order of removal.
20-34
Front Door Glass Outer Weatherstrip Replacement
NOTE:
• Put on gloves to protect your hands.
• Take care not to scratch the door.
3. From the inside of the door, slide the clips (A) of the
door glass outer weatherstrip (B) to release the hooks
(C) from the flanges (D) of the door.
1. Remove
. 2-door
these
Items:
• Door panel
- 2-door (see page 20-12)
- 4-door (see page 20-17)
• Plastic cover, as needed (see step 3 on page 20-21)
• Power mirror (see page 20-62)
2. Remove the screws from the front and rear edges of
the door.
Fastener Locations
• : Screw, 2
(Engaged
position)
(Releasee
' position)
4-door
position)
position)
(cont'd)
20-35
Doors
Front Door Glass Outer
Weatherstrip Replacement (cont'd)
Front Door Outer Molding
Replacement
4. Pull up the door glass outer weatherstrip (A), then
remove it.
Special Tools Required
KTC Trim Tool Set SOJATP2014*
^Available through the Honda Tool and Equipment
Program; call 888-424-6857
NOTE:
• If you remove the door outer molding, replace it with a
new one because it will bend during removal.
• Put on gloves to protect your hands.
• Take care not to scratch the door.
© Use the appropriate tool from the KTC trim tool set to
avoid damage when removing components.
• 4-door is shown; 2-door is similar.
1 . Remove the power mirror (see page 20-62).
5. Before installing the door glass outer weatherstrip,
slide the clips to the released position as in step 3.
6. Install the door glass outer weatherstrip, and slide the
clips securely on to the flanges.
7. Reinstall all remaining removed parts and note these
items:
• Make sure the plastic cover on the door is installed
properly and sealed around its outside perimeter to
seal out water.
• Check for water leaks (see step 9 on page 20-57).
20-36
2. Detach the clip with a clip l e m o v e r , then pulf back the
door weatherstrip (A), and remove the screw securing
the door outer molding (B).
Fastener Locations
0 :Clip, 1
•
: Screw, 1
Front 12)©©? Wm±fc®v®mp
Replacement
3. Pull out the upper edge of the door outer molding (A)
from the edge of the sash, and cut the double-sided
adhesive tape (B) with a utility knife, then remove the
molding from the sash, and remove the molding from
between the door glass outer weatherstrip (C) and the
door.
NOTE:
• Put on gloves to protect your hands.
• Take care not to scratch the door.
• Take care not to damage the front upper corner clip
(black) (4-door) and the rear upper corner clips (black)
because they are not available separately.
• Use a clip remover to remove the clips.
1. Remove the door checker mounting bolt (A) at the
A-pillar.
2-door
Fastener Locations
c
4. Scrape off remaining double-sided adhesive tape
from the sash, then clean the sash surface with a shop
towel dampened in isopropyl alcohol.
5. Install the door outer molding in the reverse order of
removal, and note these items:
• Insert the front edge of the molding between the
door glass outer weatherstrip and the door
properly.
• Push adhesive areas into place securely.
• Make sure the upper and lower sides of the molding
are catching the edges of the sash properly.
• Push the clip into place securely.
8 x 1.25 m m
29 N-m
(3.0 k g f m , 22 ibfft)
(cont'd)
20-37