PIR CM100 - ConnectM

advertisement
M100
PIR CM100
Data sheet
V1.1
Page 2
Product overview
PIR CM100 is a Pyroelectric Infrared Ray Sensor capable of detecting Human
Movement & luminous intensity. The combined motion and light detection features
enables the sensor to offer extended savings of energy by intelligently controlling lights
based on the environmental conditions. This product comprises of an Opto sensor,
providing occupancy and light level detection.
This sensor is a microcontroller based device, and hence the following parameters can
be programmed with the help of an IR Device:
 Time delay
 Luminous Intensity Threshold
 Sensitivity Adjustment
This is a Ceiling Mounted Sensor and is accompanied by a range of Accessories such as
Mounting plate and necessary wiring connector. The produce is very sleek and
aesthetically appealing. This product will not virtually disturb the building occupants.
PIR sensors when installed in busy-offices, IT or ITES buildings has a potential to save
energy anywhere in the range of 20-50% of the lighting load. This is proved by various
studies that even during the busy office day people are often away from their desks for
various reasons. Added to that building which have abundant availability of natural
source of light can be highly benefitted and can go for additional savings by utilizing
the Luminous intensity threshold parameter.
PIR sensor is easily installable and reliable. Adequate Safety and convenience is built
into the product which aids in Occupants comfort and ease of installation.
This PIR sensor works in 2 modes:
Stand-alone mode: In this mode, lights are directly connected to PIR sensor. So sensor
controls light load based on occupancy information and light available from natural
source.
In-Network mode: PIR sensor is compatible with ConnectM Energy Gateway which
aids in central control of Lighting within a building whereby, occupancy can be checked
from outside and intruders can be detected and deterred.
Page 3
Features
 Special Fresnel lens design for wide angle detection of 1350.
 SMPS based design which gives protection against High voltage surges.
 Dual passive infrared detective technology provides high response with excellent
common mode performance (match) and decreases chances of false triggering due to
temperature changes.
High accuracy ambient light sensing technology for light control based on light
level.
Microcontroller based design for improved resolution of detection.
Adjustable motion detection sensitivity, off delay and light level.
Low power consumption.
Wall & ceiling mounting.
Easy installation.
Compatible with Energy gateway and handheld programmer.







Electrical Specification
1
Operating Voltage
180-265V
2
Operating Frequency
50HZ
3
Maximum load current
2A
4
Power consumption
<3.5 W
5
Operating temperature range
0-50 C
6
Sensor output
7
Maximum Output Load
Power Output: 230V AC 50Hz
Data output: 12V
288 Watts
Page 4
Functional Specification
1
Movement detection
Human body movements emit Infra red
radiations. These radiations are basically due to
heat variations from the body. These are sensed
using a PIR (Pyroelectric InfraRed detector)
sensor.
2
Warm up time
15 Seconds
3
Sensing Angle
< 135 deg. @ 250C temp.
4
Sensing Distance
5 meters @ 250C temp. and at an height of 2.5
Meters.
5
Sensitivity adjustment
Sensitivity can be adjusted at various levels of
sensitivity (1-10 levels) through Infrared remote
control supplied by ConnectM.
6
LUX level adjustment
0-50000 Lux
(Factory programmed LUX level is >300)
7
OFF Delay
Adjusted through Infrared remote control
supplied by ConnectM.
(10 minutes is the recommended delay)
8
Strategic Locations at
which sensors are
implemented
workstation, data centre, corridor, conference
room, cabins, etc.
9
Methods of
Communication
Infrared remote control/ P2P
Page 5
Mechanical Specification
1
International protection standard
IP44
2
Mounting surface
Ceiling mount
3
Overall dimension
100mm diameter, 65mm height
4
Weight
200 g (excluding cable)
Specifications at 240V AC @ 250C
This product is recommended for INDOOR USE ONLY
No user serviceable parts inside
Recommended Installation Height:
135
Deg
2.5 M
5.0 M
Download